Configs for ARM corelink SSE-200 target and Musca A board

This patch adds configuration files for ARM CoreLink SSE-200 SoCs. Also
adds configuration file for SSE-200 based Musca A board. Flash programming
support for Musca A QSPI flash is still not functional. This configuration
will be updated once that support lands into OpenOCD.

Please refer to ARM documentation for more information about SSE-200 and
Musca A.

Change-Id: Id3783c34d6e2609d659ef91c0bf7252c39439874
Signed-off-by: Omair Javaid <[email protected]>
Reviewed-on: http:https://openocd.zylin.com/5006
Tested-by: jenkins
Reviewed-by: Matthias Welwarsky <[email protected]>

tcl/board/arm_musca_a.cfg

@@ -0,0 +1,44 @@
+#
+# Configuration script for ARM Musca-A development board
+#
+# For now we do not support Musca A flash programming using OpenOCD. However, a
+# work area is configured for flash programming speed up.
+#
+# GDB considers all memory as RAM unless target supplies a memory map.
+# OpenOCD will only send memory map if flash banks are configured. Otherwise,
+# configure GDB after connection by issuing following commands:
+# (gdb) mem 0x10200000 0x109FFFFF ro
+# (gdb) mem 0x00200000 0x009FFFFF ro
+# (gdb) set mem inaccessible-by-default off
+
+# ARM Musca A board supports both JTAG and SWD transports.
+source [find target/swj-dp.tcl]
+
+# set a safe JTAG clock speed, can be overridden
+adapter_khz 1000
+
+global _CHIPNAME
+if { [info exists CHIPNAME] } {
+ set _CHIPNAME $CHIPNAME
+} else {
+ set _CHIPNAME MUSCA_A
+}
+
+if { [info exists CPUTAPID] } {
+ set _CPUTAPID $CPUTAPID
+} else {
+ set _CPUTAPID 0x6ba00477
+}
+
+# Enable CPU1 debugging as a separate GDB target
+set _ENABLE_CPU1 1
+
+# Musca A1 has 32KB SRAM banks. Override default work-area-size to 8KB per CPU
+set WORKAREASIZE_CPU0 0x2000
+set WORKAREASIZE_CPU1 0x2000
+
+# Set SRAM bank 1 to be used for work area. Override here if needed.
+set WORKAREAADDR_CPU0 0x30008000
+set WORKAREAADDR_CPU1 0x3000A000
+
+source [find target/arm_corelink_sse200.cfg]

tcl/target/arm_corelink_sse200.cfg

@@ -0,0 +1,71 @@
+#
+# Configuration script for Arm CoreLink SSE-200 Subsystem based IoT SoCs.
+#
+
+global TARGET
+set TARGET $_CHIPNAME
+
+swj_newdap $_CHIPNAME cpu -irlen 4 -expected-id $_CPUTAPID
+dap create $_CHIPNAME.dap -chain-position $_CHIPNAME.cpu
+
+#
+# SRAM on ARM CoreLink SSE-200 can be 4 banks of 8/16/32/64 KB
+# We will configure work area assuming 8-KB bank size in SRAM bank 1.
+# Also SRAM start addresses defaults to secure mode alias.
+# These values can be overridden as per board configuration
+#
+
+global _WORKAREASIZE_CPU0
+if { [info exists WORKAREASIZE_CPU0] } {
+ set _WORKAREASIZE_CPU0 $WORKAREASIZE_CPU0
+} else {
+ set _WORKAREASIZE_CPU0 0x1000
+}
+
+global _WORKAREAADDR_CPU0
+if { [info exists WORKAREAADDR_CPU0] } {
+ set _WORKAREAADDR_CPU0 $WORKAREAADDR_CPU0
+} else {
+ set _WORKAREAADDR_CPU0 0x30008000
+}
+
+#
+# Target configuration for Cortex M33 Core 0 on ARM CoreLink SSE-200
+# Core 0 is the boot core and will always be configured.
+#
+
+target create ${TARGET}.CPU0 cortex_m -dap $_CHIPNAME.dap -ap-num 1 -coreid 0
+
+${TARGET}.CPU0 configure -work-area-phys $_WORKAREAADDR_CPU0 -work-area-size $_WORKAREASIZE_CPU0 -work-area-backup 0
+
+${TARGET}.CPU0 cortex_m reset_config sysresetreq
+
+#
+# Target configuration for Cortex M33 Core 1 on ARM CoreLink SSE-200
+# Core 1 is optional and locked at boot until core 0 unlocks it.
+#
+
+if { $_ENABLE_CPU1 } {
+ global _WORKAREASIZE_CPU1
+ if { [info exists WORKAREASIZE_CPU1] } {
+ set _WORKAREASIZE_CPU1 $WORKAREASIZE_CPU1
+ } else {
+ set _WORKAREASIZE_CPU1 0x1000
+ }
+
+ global _WORKAREAADDR_CPU1
+ if { [info exists WORKAREAADDR_CPU1] } {
+ set _WORKAREAADDR_CPU1 $WORKAREAADDR_CPU1
+ } else {
+ set _WORKAREAADDR_CPU1 0x30009000
+ }
+
+ target create ${TARGET}.CPU1 cortex_m -dap $_CHIPNAME.dap -ap-num 2 -coreid 1
+
+ ${TARGET}.CPU1 configure -work-area-phys $_WORKAREAADDR_CPU1 -work-area-size $_WORKAREASIZE_CPU1 -work-area-backup 0
+
+ ${TARGET}.CPU1 cortex_m reset_config vectreset
+}
+
+# Make sure the default target is the boot core
+targets ${TARGET}.CPU0