PedalTuner is a simple application that allows users of pedals from manufacturers like Fanatec whose software does not support fine tuning the pedal output via curves.

While it has been primarily designed for iRacing and Fanatec V3 brake pedals it may (but also may not) work on other devices and input signal.

PedalTuner grabs the signal coming from a pedal, transforms it, and emits the transformed signal via an emulated device.

Using this software is at your own risk.

It is far from being exhaustively tested and is still a prototype. The way in which this tool works inherently introduces lag while consuming additional resources.

Additionally, given that the emulated device uses an emulated XBOX360 trigger controller, the output pedal only has a resolution of 255 values, as opposed to the 65535 possible values of the original.

The best solution is always for the manufacturer to implement this functionality in their software, but this is intended to provide a potential interim solution.

Before using this application you must install and setup the ViGEmBus. ViGEmBus helps us emulate game controllers that we can use to output the transformed signal through.

1. Download and install from https://github.com/ViGEm/ViGEmBus/releases

PedalTuner has been tested with v1.21.442.

You may download PedalTuner from the releases page: https://github.com/scermat/MSS.PedalTuner/releases

PedalTuner is a portable application, simply extract the contents of the zip file and run the MSS.PedalTuner.exe executable.

Preferably make sure to swtich on all your controller devices before launching PedalTuner, and launch PedalTuner before launching the sim.

1. Open PedalTuner by running the MSS.PedalTuner.exe executable
2. Click Settings > InputDevice to open up the config screen
3. Click Load Input Devices to scan your PC for connected steering wheel devices. This may take a while. Note that if your device is not recognised, you may untick Scan for wheel devices only to load up all HID devices. This will be a cluttered list but should include all devices.
4. Select the Input Device from the drop down. Note: you may have to reselect if it was selected automatically
5. Click Calibrate and follow the prompts
6. Click Test and modulate pressure on the pedal to make sure input is detected ok.
7. Click Save

If the calibration wizard fails you may set it up manually by populating the:

• Input Device: The device the original pedal is connected from
• Controller Property: The controller property which exposes the pedal input value (you may refer to the Controller Parameters window while modulating the pedal to identify the appropriate property)
• Min Value: The minimum value reported by the pedal
• Max Value: The maximum value reported by the pedal
• Invert Value: Check this when the pedal is at Max Value when it is released, and when it is at MinValue when it is fully pressed (Fanatec V3s require this checked. Probably so do other pedals but I have no way to test)

To reset configuration at any time and restart, please remove the pedaltuner.settings.json file from the folder in which PedalTuner is installed.

To use PedalTuner, define the filter, factor and interval and click Monitor.

To confirm PedalTuner is working, refer to the In and Out trackbars. If both are moving to the pedal input then you should be set.

The filter and factor may be updated at any time (even in-game) by clicking Set Params to confirm new values.

From personal testing, I found an interval of 25 to be sufficient. Feel free to tweak this value to suit your needs and specs.

Settings are Saved automatically so setup is only required once.

To setup in iRacing we must tell the iRacing controller setup screen that we want the pedal signal to be captured from the emulated device.

To do so, go through the pedal setup wizard as normal, but when setting the PedalTuner pedal, go to Settings > Game Setup and click the Set Maximum and Set Minimum buttons in line with wizard request. You should see the signal coming from a new device and the maximum value being 255.

You may need to click the buttons repeatedly for the signal to be detected.

Special thanks to zaid92 for testing with Thrustmaster LC pedals, and the TDi99 community for the help, inspiration and entertainment.