Preliminary 30wer firmware. Not tested on real board yet.

keyboards/30wer/30wer.c

@@ -0,0 +1 @@
+#include "30wer.h"

keyboards/30wer/30wer.h

@@ -0,0 +1,14 @@
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT( \
+ k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c, \
+ k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c, \
+ k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b \
+) \
+{ \
+ { k00, k01, k02, k03, k04, k05, k06, k07, k08, k09, k0a, k0b, k0c }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1a, k1b, k1c }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2a, k2b } \
+}

keyboards/30wer/config.h

@@ -0,0 +1,31 @@
+#pragma once
+
+#include "config_common.h"
+
+/* USB Device descriptor parameter */
+#define VENDOR_ID 0x1234
+#define PRODUCT_ID 0x5678
+#define DEVICE_VER 0x0000
+#define MANUFACTURER 8o7wer
+#define PRODUCT 30wer
+#define DESCRIPTION Gherkin style construction 30% staggered pcb kit
+
+/* key matrix size */
+#define MATRIX_ROWS 3
+#define MATRIX_COLS 13
+
+/* pcb default pin-out */
+#define MATRIX_ROW_PINS { E6, B4, B5 }
+#define MATRIX_COL_PINS { F4, F5, F6, F7, B1, B3, B2, B6, D1, D0, D4, C6, D7 }
+#define UNUSED_PINS
+
+/* COL2ROW or ROW2COL */
+#define DIODE_DIRECTION COL2ROW
+
+/* key combination for command */
+#define IS_COMMAND() ( \
+ keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \
+)
+
+/* prevent stuck modifiers */
+#define PREVENT_STUCK_MODIFIERS

keyboards/30wer/keymaps/default/keymap.c

@@ -0,0 +1,21 @@
+#include QMK_KEYBOARD_H
+
+enum wer_layers {
+ _QWERTY,
+ _LOWER,
+ _RAISE,
+};
+
+
+#define LOWER MO(_LOWER)
+#define RAISE MO(_RAISE)
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+
+[_QWERTY] = LAYOUT( \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_BSPC, KC_DEL, \
+ KC_LCTL, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_SPC \
+),
+
+};

keyboards/30wer/readme.md

@@ -0,0 +1,4 @@
+30wer by 8o7wer
+===
+
+Should put some text here.

keyboards/30wer/rules.mk

@@ -0,0 +1,60 @@
+# MCU name
+MCU = atmega32u4
+
+# Processor frequency.
+# This will define a symbol, F_CPU, in all source code files equal to the
+# processor frequency in Hz. You can then use this symbol in your source code to
+# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
+# automatically to create a 32-bit value in your source code.
+#
+# This will be an integer division of F_USB below, as it is sourced by
+# F_USB after it has run through any CPU prescalers. Note that this value
+# does not *change* the processor frequency - it should merely be updated to
+# reflect the processor speed set externally so that the code can use accurate
+# software delays.
+F_CPU = 16000000
+
+#
+# LUFA specific
+#
+# Target architecture (see library "Board Types" documentation).
+ARCH = AVR8
+
+# Input clock frequency.
+# This will define a symbol, F_USB, in all source code files equal to the
+# input clock frequency (before any prescaling is performed) in Hz. This value may
+# differ from F_CPU if prescaling is used on the latter, and is required as the
+# raw input clock is fed directly to the PLL sections of the AVR for high speed
+# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
+# at the end, this will be done automatically to create a 32-bit value in your
+# source code.
+#
+# If no clock division is performed on the input clock inside the AVR (via the
+# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
+F_USB = $(F_CPU)
+
+# Interrupt driven control endpoint task(+60)
+OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
+
+# Bootloader
+# This definition is optional, and if your keyboard supports multiple bootloaders of
+# different sizes, comment this out, and the correct address will be loaded
+# automatically (+60). See bootloader.mk for all options.
+BOOTLOADER = caterina
+
+# Build Options
+# change to "no" to disable the options, or define them in the Makefile in
+# the appropriate keymap folder that will get included automatically
+#
+BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
+MOUSEKEY_ENABLE = no # Mouse keys(+4700)
+EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
+CONSOLE_ENABLE = yes # Console for debug(+400)
+COMMAND_ENABLE = no # Commands for debug and configuration
+NKRO_ENABLE = yes # Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
+BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality
+MIDI_ENABLE = no # MIDI controls
+AUDIO_ENABLE = no # Audio output
+UNICODE_ENABLE = no # Unicode
+BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
+RGBLIGHT_ENABLE = no # Enable WS2812 RGB underlight.