Merge remote-tracking branch 'origin/master' into develop

keyboards/handwired/tractyl_manuform/5x6_right/config.h

@@ -41,8 +41,6 @@ along with this program. If not, see <http:https://www.gnu.org/licenses/>.
 #define DYNAMIC_KEYMAP_LAYER_COUNT 16
 #define LAYER_STATE_16BIT
 
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCE 5
 
 /* disable action features */
 //#define NO_ACTION_LAYER

keyboards/handwired/tractyl_manuform/5x6_right/f411/config.h

@@ -44,11 +44,11 @@ along with this program. If not, see <http:https://www.gnu.org/licenses/>.
 #define WS2812_DMA_STREAM STM32_DMA1_STREAM7 // DMA Stream for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
 #define WS2812_DMA_CHANNEL 3 // DMA Channel for TIMx_UP, see the respective reference manual for the appropriate values for your MCU.
 
-#define RGBLED_NUM 20
+#define RGBLED_NUM 52
 #define RGBLIGHT_SPLIT
 #define RGBLED_SPLIT \
- { 10, 10 }
-#define RGBLIGHT_LMIT_VAL 80
+ { 26, 26 }
+#define RGBLIGHT_LIMIT_VAL 150
 
 #define DEBUG_LED_PIN C13
 

keyboards/handwired/tractyl_manuform/5x6_right/f411/readme.md

@@ -1,16 +1,21 @@
 # Drashna's Blackpill Tractyl Manuform (5x6) with a right side trackball
 
-* VBUS mod, using PB10
+* System Timer on TIM5
+* ~~VBUS mod, using PB10~~ (*doesn't seem to work for me*)
 * Split Hand Pin, using PC14
-* Full Duplex Serial/USART using PA3 and PA4 on USART2
+* Full Duplex Serial/USART using PA2 and PA3 on USART2
 * PWM Audio using PB1 and TIM3 and GPT on TIM4
-* PWM RGB using PA1 TIM2
-* pmw3360 sensor sharing PA5-PA7 on SPI1, with B0 as CS pin
+* PWM WS2812 RGB using PA1 TIM2
 * 8KB SPI EEPROM chip sharing PA5-PA7 on SPI1 with PA4 as CS pin
+* pmw3360 sensor sharing PA5-PA7 on SPI1, with B0 as CS pin
 * Encoder using PA13 and PA14
 * SSD1306 OLED display (128x64) using PB8-PB9 on I2C1
 * Pull-up resistor (22k) on PA10 to fix reset issue.
 * Pull-up resistor (5.1k) on PA1 for WS2812 LED support, and wire it's VCC to the 5V pin.
+* Pins PA9, PA11, A12 are not useable because they're used for USB connection, and can't be shared. 
+* Pin PB2 is used by BOOT1, and is unusable
+
+## Keyboard Info
 
 * Keyboard Maintainer: [Drashna Jael're](https://github.com/drashna)
 * Hardware Supported: [Design files](https://gitlab.com/keyboards1/dm_r_track/-/tree/master/boolean), [WeAct BlackPill (F411)](https://github.com/WeActTC/MiniSTM32F4x1), [PMW3360 Optical Sensor](https://www.tindie.com/products/jkicklighter/pmw3360-motion-sensor/)
@@ -24,3 +29,9 @@ Flashing example for this keyboard:
  make handwired/tractyl_manuform/5x6_right/f411:default:flash
 
 See the [build environment setup](https://docs.qmk.fm/#/getting_started_build_tools) and the [make instructions](https://docs.qmk.fm/#/getting_started_make_guide) for more information. Brand new to QMK? Start with our [Complete Newbs Guide](https://docs.qmk.fm/#/newbs).
+
+## Bootloader 
+
+* **Bootmagic reset**: Hold down the top right key on the right side, or the top left key on the left side while plugging in.
+* **Physical reset button**: Briefly press the "USER" button on the BlackPill
+* **Keycode in layout**: Press the key mapped to `RESET`.

keyboards/handwired/tractyl_manuform/5x6_right/f411/rules.mk

@@ -6,8 +6,11 @@ BOOTLOADER = stm32-dfu
 
 KEYBOARD_SHARED_EP = yes
 CONSOLE_ENABLE = yes
+MOUSE_SHARED_EP = no
 
 EEPROM_DRIVER = spi
 WS2812_DRIVER = pwm
 SERIAL_DRIVER = usart
 AUDIO_DRIVER = pwm_hardware
+
+DEBOUNCE_TYPE = asym_eager_defer_pk

keyboards/handwired/tractyl_manuform/5x6_right/keymaps/drashna/config.h

@@ -16,16 +16,7 @@
 
 #pragma once
 
-// #define USE_I2C
-// #define SELECT_SOFT_SERIAL_SPEED 1
-// #define SERIAL_USE_MULTI_TRANSACTION
-#define SPLIT_MODS_ENABLE
-#define EE_HANDS
-
 #define TRACKBALL_DPI_OPTIONS { 1200, 1800, 2600, 3400 }
 
 #undef DEBOUNCE
-#define DEBOUNCE 10
-
-#define SOLENOID_PIN F1
-#define SOLENOID_DEFAULT_DWELL 8
+#define DEBOUNCE 15

keyboards/handwired/tractyl_manuform/5x6_right/keymaps/drashna/keymap.c

@@ -348,16 +348,8 @@ void render_kitty(void) {
  0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x01, 0x01, 0x01, 0x06, 0x04, 0x04, 0x04, 0x04, 0x05, 0x04, 0x04, 0x04, 0x07, 0x07, 0x07, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00}};
 
  // assumes 1 frame prep stage
-#ifdef SWAP_HANDS_ENABLE
- extern bool swap_hands;
-#endif
  void animation_phase(void) {
-# ifdef SWAP_HANDS_ENABLE
- if (swap_hands)
-#else
- if (tap_toggling)
-#endif
- {
+ if (tap_toggling) {
  anim_frame_duration = 300;
  current_rtogi_frame = (current_rtogi_frame + 1) % RTOGI_FRAMES;
  oled_write_raw_P(rtogi[abs((RTOGI_FRAMES - 1) - current_rtogi_frame)], ANIM_SIZE);

keyboards/handwired/tractyl_manuform/config.h

@@ -24,9 +24,6 @@ along with this program. If not, see <http:https://www.gnu.org/licenses/>.
 #define VENDOR_ID 0x44DD
 #define MANUFACTURER Drashna
 
-/* Set 0 if debouncing isn't needed */
-#define DEBOUNCE 5
-
 #define USB_POLLING_INTERVAL_MS 1
 
 /* disable debug print */

users/drashna/config.h

@@ -147,6 +147,9 @@
 // # define OLED_FONT_5X5
 // # define OLED_FONT_AZTECH
 // # define OLED_FONT_BMPLAIN
+// # define OLED_FONT_CRACKERS
+// # define OLED_FONT_HISKYF21
+# define OLED_FONT_DEAD_MEAL
 // # define OLED_FONT_SUPER_DIGG
 // # define OLED_LOGO_GMK_BAD
 // # define OLED_LOGO_HUE_MANITEE
@@ -163,17 +166,12 @@
 # define ONESHOT_TIMEOUT 3000
 #endif // !ONESHOT_TIMEOUT
 
-// this makes it possible to do rolling combos (zx) with keys that
-// convert to other keys on hold (z becomes ctrl when you hold it,
-// and when this option isn't enabled, z rapidly followed by x
-// actually sends Ctrl-x. That's bad.)
-#define IGNORE_MOD_TAP_INTERRUPT
-#undef PERMISSIVE_HOLD
-//#define TAPPING_FORCE_HOLD_PER_KEY
-//#define RETRO_TAPPING_PER_KEY
-#if !defined(KEYBOARD_kyria) && !defined(KEYBOARD_splitkb_kyria)
-# define TAPPING_TERM_PER_KEY
-#endif
+#define IGNORE_MOD_TAP_INTERRUPT_PER_KEY
+#define PERMISSIVE_HOLD_PER_KEY
+#define TAPPING_FORCE_HOLD_PER_KEY
+#define RETRO_TAPPING_PER_KEY
+#define TAPPING_TERM_PER_KEY
+
 
 #ifndef TAPPING_TOGGLE
 # define TAPPING_TOGGLE 1

users/drashna/drashna.c

@@ -259,3 +259,61 @@ void matrix_slave_scan_user(void) {
  matrix_slave_scan_keymap();
 }
 #endif
+
+__attribute__((weak)) uint16_t get_tapping_term(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ default:
+ return TAPPING_TERM;
+ }
+}
+
+__attribute__((weak)) bool get_permissive_hold(uint16_t keycode, keyrecord_t *record) {
+ // Immediately select the hold action when another key is tapped:
+ // return true;
+ // Do not select the hold action when another key is tapped.
+ // return false;
+ switch (keycode) {
+ default:
+ return false;
+ }
+}
+
+__attribute__((weak)) bool get_hold_on_other_key_press(uint16_t keycode, keyrecord_t *record) {
+ // Immediately select the hold action when another key is pressed.
+ // return true;
+ // Do not select the hold action when another key is pressed.
+ // return false;
+ switch (keycode) {
+ case QK_LAYER_TAP ... QK_LAYER_TAP_MAX:
+ return true;
+ default:
+ return false;
+ }
+}
+
+__attribute__((weak)) bool get_ignore_mod_tap_interrupt(uint16_t keycode, keyrecord_t *record) {
+ // Do not force the mod-tap key press to be handled as a modifier
+ // if any other key was pressed while the mod-tap key is held down.
+ // return true;
+ // Force the mod-tap key press to be handled as a modifier if any
+ // other key was pressed while the mod-tap key is held down.
+ // return false;
+ switch (keycode) {
+ default:
+ return true;
+ }
+}
+
+__attribute__((weak)) bool get_tapping_force_hold(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ default:
+ return false;
+ }
+}
+
+__attribute__((weak)) bool get_retro_tapping(uint16_t keycode, keyrecord_t *record) {
+ switch (keycode) {
+ default:
+ return false;
+ }
+}