Skip to content
/ catalyst Public
forked from livepeer/catalyst

Livepeer's Decentralized Media Server

License

Notifications You must be signed in to change notification settings

omahs/catalyst

 
 

Repository files navigation

Catalyst

The entire bundle needed for booting up Livepeer's decentralised media server in place is termed as Catalyst.

Getting Started

Make sure you have the following installed on the machine before proceeding.

Note: Compiling Mistserver/go-livpeeer etc have another set of requirements, not listed here (but covered under compile from source section below).

Mandatory requirements

  • go1.17± or newer
  • GNU make
  • about 2-3 GB of free disk space

Optional

  • ffmpeg v5 or newer (can be compiled from go-livepeer, by running make ffmpeg)

  • Docker version 19 or newer

  • cloning this repository alongside go-livepeer, MistServer and other dependent projects of Catalyst in the same directory. Directories would look like:

    /path/to/projects
                |- catalyst/
                |- go-livepeer/
                |- mistserver/
    

±: go1.17 is recommended because building with < 1.17 (specifically 1.16) can result in issues on arm64 architectures.

Setting up Catalyst system

First run (or reset workflow)

Run make full-reset which cleans out any older config files, and local copies of binaries. It also shuts down docker-compose system which aren't needed for base Catalyst usage.

Using prebuilt binaries (download-and-run)

This section covers using prebuilt binaries for setting up and booting Catalyst system. This is done through using the configuration present in manifest.yaml (section below covers its structure).

Run the following commands from the root of this repository directory:

go build -o ./bin/livepeer-log ./cmd/livepeer-log/livepeer-log.go
go run cmd/downloader/downloader.go

# or, single command:
make all

Other options available for downloader script can be checked with using --help.

The above should download all prebuilt binaries to the bin/ directory.

Compile from source (build-and-run)

This section covers building the dependent projects before booting up Catalyst. There are quite a few applications needed for Catalyst as listed below (but not limited to):

A few of these can be compiled using Makefile recipes, but others need to be compiled as described in their respective project docs and the compiled binary would need to be ported to bin/ afterwards (can be symlinked instead).

Requirements for compiling MistServer

  • git
  • gcc or clang
  • CMake
  • about 4 GB of free disk space

Requirements for compiling go-livepeer

  • go1.17 (for arm64 build support)
  • git
  • GNU make
  • CMake
  • gcc-multilib
  • autoconf
  • pkg-config
make mistserver
make go-livepeer
make livepeer-log

Running Catalyst

The command does some memory allocation on macOS too, but for linux it is as simple as launching MistController with path to configuration file.

Next is just booting up the Catalyst system:

make dev

Which will create a copy of developer config file to ~/.config/livepeer/catalyst.json (default path) and use that to boot up MistController; which controls and monitors setting up other required sub-systems. An example of MistController starting up Livepeer broadcaster is shown in logs as follows:

[2022-09-22 15:32:30] MistController (2244175) CONF: Starting connector: {"broadcaster":true,"connector":"livepeer","metricsClientIP":true,"metricsPerStream":true,"monitor":true,"orchAddr":"localhost:8936","rtmpAddr":"127.0.0.1:1936"}
[2022-09-22 15:32:30] MistController (2244175) INFO: added logger for livepeer
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.537623 2244406 starter.go:333] ***Livepeer is running on the offchain network***
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539038 2244406 census.go:323] Compiler: gc Arch amd64 OS linux Go version go1.17.13
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539078 2244406 census.go:324] Livepeer version: 0.5.34-80e70628
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539101 2244406 census.go:325] Node type bctr node ID livepeer.system
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539449 2244406 starter.go:491] ***Livepeer is in off-chain mode***
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539595 2244406 starter.go:1156] ***Livepeer Running in Broadcaster Mode***
[2022-09-22 15:32:30] livepeer (2244394) INFO: I0922 15:32:30.539667 2244406 starter.go:1157] Video Ingest Endpoint - rtmp:https://127.0.0.1:1936

You should then have a Mist interface accessible at http:https://localhost:4242.

Credentials/secrets

MistServer credentials:

username: test
password: test

Hot reloading

If a binary is replaced in the bin/ directory, no need to shutdown the whole catalyst process, and simply running for eg. killall livepeer for restarting livepeer binary works. MistController keeps track of all sub-systems and boots them back up in case they exit.

Streaming

This section will cover stream and playback using HLS to local Catalyst system.

Using ffmpeg

The RTMP stream endpoint is accessible at rtmp:https://localhost/live/video+<PLAYBACK_ID>, so an example stream could be started (using ffmpeg) as follows:

ffmpeg -re -stream_loop -1 \
  -i "/path/to/video/file.mp4" \
  -c:v copy -c:a copy -strict -2 \
  -f flv \
  rtmp:https://localhost/live/video+foo

where the PLAYBACK_ID is foo.

Using OBS Studio

Under OBS Studio streaming settings, select "Serive" as "Custom..." which should display text input options asking for "Server" and "Stream Key" (ref. screenshot below). Use following values for the same:

Server: rtmp:https://localhost/live
Stream Key: video+<PLAYBACK_ID>

Deselect the option to "Use authentication". The example (as shown in screenshot) uses video+foo as the "Stream Key".

obs-studio

Playback

Playback over HLS is available through m3u8 playlist file accessible at http:https://localhost:8080/hls/video+<PLAYBACK_ID>/index.m3u8. For the example stream above, playback can be started with:

ffplay http:https://localhost:8080/hls/video+foo/index.m3u8

Manifest

The manifest.yaml file specifies which services are needed for the system to bootup. The fields (with some description) are shown below:

# Manifest versioning, should be a fixed value
version: 3.0

# Default release/tag for projects. Keeping it latest
# will have the script search for most recent tag using
# the github API
release: latest

# Services inside the box
box:
    # array of each service element
    - name: name

      # custom release value (if working on specific tag)
      # Can be the branch name for `bucket` strategy (see below)
      release: v99.99.99

      # override artifact name generation pattern. default pattern is:
      # <name>-<platform>-<arch>.tar.gz for linux/macos
      # <name>-<platform>-<arch>.zip for windows
      # overrides to using `<binary>-<platform>-<arch>.<ext>`
      binary: livepeer-www

      # path inside the archive zip/tar which is needed for the service
      archivePath: victoria-metrics-prod

      # output name of the binary located at `archivePath`
      outputPath: livepeer-victoria-metrics

      # Strategy to use for downloading artifacts: github or bucket
      # `bucket` - Uses `build.livepeer.live` bucket; works for branches of some projects
      # `github` - Uses github releases and tags (default value)
      strategy:
          download: github
          # `project` => github project/repo or bucket key for artifacts
          project: livepeer/project-name
          # `commit` => repository commit SHA (useful for bucket strategy)
          commit: 0000000000000000000000000000000000000000

      # key-value for mapping platform to custom artifact on github release page
      # this bypasses default name generation pattern entirely
      srcFilenames:
          linux-amd64: victoria-metrics-amd64-v1.74.0.tar.gz
          linux-arm64: victoria-metrics-arm64-v1.74.0.tar.gz
          darwin-amd64: victoria-metrics-darwin-amd64-v1.74.0.tar.gz
          darwin-arm64: victoria-metrics-darwin-arm64-v1.74.0.tar.gz

      # Skip gpg signature verification step
      skipGpg: true

      # Skip sha digest check for artifact
      skipChecksum: true

      # Skip checking for newer releases (default is false)
      skipManifestUpdate: true

About

Livepeer's Decentralized Media Server

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • Go 77.7%
  • Makefile 9.0%
  • Shell 8.9%
  • Dockerfile 4.4%