This software uses Hi-C sequencing data to assemble contigs/scaffolds into complete chromosomes. The assembly process consists of the following steps:
- creation of corrected Hi-C contact matrix
- detection of mis-assemblies (automatic and/or manual)
- creation of initial path graph
- iterative joining of high-confidence scaffold paths
- addition of scaffolds that were not used yet
- saving of scaffolds fasta file and liftover chain file
HiCAssembler automatically visualizes the assembly process to inform the user on the assembly status
HiCAssembler works with python 2.7 and requires that HiCExplorer is installed
To install HiCAssembler use pip.
$ pip install HiCAssembler
If you want to install the latest version use:
$ pip install git+https://github.com/maxplanck-ie/HiCAssembler.git
Before running HiCAssembler, creation of a corrected Hi-C matrix in h5 format is required. This file format is the output created by HiCExporer (https://hicexplorer.readthedocs.io/). Hi-C reads need to be mapped to your pre-assembled contigs/scaffolds and then the Hi-C matrix needs to be created and corrected. An example usage of HiCExporer for these steps can be found at https://hicexplorer.readthedocs.io/en/latest/content/example_usage.html.
Afterwards, you can start to assemble your pre-assembled contigs/scaffolds into chromosomes using HiCAssembler.
$ assemble -m Hi_C_matrix_corrected.h5 -o ./assembly_output \
--min_scaffold_length 100000 --bin_size 5000 --misassembly_zscore_threshold -1.0 \
--num_iterations 3 --num_processors 16
--min_scaffold_length 100000
sets the minimal length of pre-assembled scaffolds
to 100 kb. Scaffolds smaller than 100 kb are added after the iterative correction.
--bin_size 5000
sets the Hi-C bin size to 5 kb. This would be the size of
high-resolution bins referred to in the algorithm description.
--misassembly_zscore_threshold -1.0
sets the threshold deciding if a
TAD-separation score is strong enough to be considered a mis-assembly.
--num_iterations 3
sets the number of assembly iterations to 3.
In case your final result contains assembly errors, you can manually correct them.
The position of assembly errors can be specified and added as a position to
cut your pre-assembled contigs/scaffolds before the assembly using the
--split_positions_file split.bed
parameter. The exact position of the error
in the pre-assembled contigs/scaffolds can be identified by using the tool
plotScaffoldInteractive
.
$ plotScaffoldInteractive scaffold_123
The position of the assembly error is displayed by moving your cursor over it.
Gina Renschler, Gautier Richard, Claudia Isabelle Keller Valsecchi, Sarah Toscano, Laura Arrigoni, Fidel Ramirez, Asifa Akhtar. "Hi-C guided assemblies reveal conserved regulatory topologies on X and autosomes despite extensive genome shuffling", Genes & Development (2019), doi: https://doi.org/10.1101/gad.328971.119
(A small corrected Hi-C matrix can be found in the data/
folder)
A minimal example of the assembly of several scaffolds:
$ assemble -m /data/hic_small.h5 -o ./assembly_output \
--min_scaffold_length 100000 --bin_size 5000 --misassembly_zscore_threshold -1.0 \
--num_iterations 3 --num_processors 16
Each step of the assembly is automatically visualized.
Now, let's see how scaffolds with and without mis-assemblies look like:
Assembly errors can easily be detected as an abrupt change in the Hi-C signal. HiCAssembler automatically splits scaffolds at minima of the Hi-C score as shown here:
Strong TAD boundaries with a low TAD-separation score can wrongly be considered as
mis-assemblies. The threshold of the score where scaffolds get split needs to
be chosen using the --misassembly_zscore_threshold
parameter.
A balance between too many splits and thus very small scaffolds after splitting
and too many left-over mis-assemblies needs to be found. We identified a score
of -1 as a good starting point for assemblies but we recommend to test several
settings. Some scaffolds will be split at TAD boundaries. This is no problem
because they will be connected again by the assembly process afterwards.
If not all mis-assemblies are split automatically, splits can be added manually
using the --split_positions_file split.bed
parameter. The exact position of
the error in the pre-assembled contigs/scaffolds can be identified by using the tool
plotScaffoldInteractive
.
$ plotScaffoldInteractive scaffold_123
The position of the assembly error is displayed by moving your cursor over it.