NOTE: This Design is still a Work in Progress. Schematic, PCB, and other stuff might change!
- Update
- Important
- Background
- Design
- Code Repositories
- Configuration of JDY-67
- Related Efforts
- Contributing
- Maintainers
- License
Important: The 20230608 version‘s symbols and footprints of Q1, Q2 are wrong. Please use updated in 20230609.
- Update LDO LM1117-3.3V to 5V, to provide a constant power for the Bluetooth module;
- Removed the Zener, and updated R6 to 150Ω, which is close to the ideal value;
- Added power off circuit.
- Replace VR with fixed resistor and optimize the circuit.
- Updated some symbols and footprints.
The version 20230522‘s MD6 and MD8 sockets footprints were forgot to be grounded, if you has printed the PCB, you can scrape the green oil next to the shell's big pin, and then solder them together. It will as good as this version 20230527.
20230527's update includes:
- Modified the symbols and footprints design of MD-6 and MD8 sockets, added pin 9, and grounded. Ensure that will not lost ground when updating from schematic.
- The power divider resistor R6 is updated to 270Ω, which is close to the ideal value;
- Added project's kicad symbols and footprints library sharing.
- Add 6.2V zener for pre-conditioning before LM1117-3.3
- Add attenuation network for Line->Mic
- Add EMI inductor on TXD/RXD pins.
- Removed TXD's LED.
- The FT-817/818's ACC jack always has a constant voltage of 13.8V, even you switched off the rig. We should BE VERY CAREFUL to avoid short-circuit the PCB and ACC jack accidentally.
- Meanwhile, aftering installing this adaptor, it will ALWAYS consume FT-817/818's battery energy. So, A battery with a power switch is recommended. For example, The WindCamp's FT-817/818 lithium battery.
- If you would purchase a JDY-67 Bluetooth moudle, make sure the firmware version is Above 1.3.
My friend BG6JJI designed a Bluetooth DIGI adaptor working for many old style TRXs with a Bluetooth, DIGI and CAT ability. He was using a Bluetooth module named JDY-67. I am not sure which manufacturer made the JDY-67. But it's really inexpensive and really works for Bluetooth Audio, and SPP in same time.
So, I pick up an old PCB design for my FT-818. It was design for FT8 cable connecting at very beginning. However, with JDY-67, It should works for Bluetooh/DIGI/CAT. I'd measured the DATA and ACC jacks on FT-818's rear panel, And refering to the FT-817ND's Service Manual, I think the Yaesu's PCB maybe design in a 0.635mm/0.025inch grid. Under this assumption, I'd drawn a PCB that could cover most of the FT-817 rear panel, and perfectly matched all the screw holes, jacks....precisely!!! It looks like a underwear(under-bottom-hardware), right?
Although FT-817/818 has been discontinued, I still love this twenty years selling product. Now, I would like to share this PCB desgin to all HAM communities, If you wanna make your design, you can make any modify from it.
This PCB was design by KiCad 7.0 In the Layer User.Drawings and User.Comments, there are some information of measurement. In the Layer User.1~4, there are approximate FT-817/818's panel sketch for comparison.
- Github https://github.com/BG6LH/FT-81x-BT-DIGI-Adaptor
- Gitee https://gitee.com/bg6lh/FT-81x-BT-DIGI-Adaptor
Please note, the JDY-67's default BAUD is 9600bps.
Before connect the adaptor to phone or computer, there are three bluetooth configuration need to be changed. please use those serial port AT instructions:
AT+SING1\r\n
# Turn on single-ended output
AT+ROLE0\r\n
# Turn off BLE bluetooth
AT+CALEN1\r\n
# Turn on the phone function
AT+RST\r\n
# Restart the moudule
Jdy-67 module serial command must be plus \r\n .
- FT8CN for Android - Run FT8 natively on Android. This app works well with our Bluetooth DIGI Adaptor.
With special thanks to BG6JJI, BI1EIH*. They give me many generous advice.
Let's enjoy the FT-817's last lucky underware together!!
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0).