[Keyboard] Add Budget96 by Donut Cables (qmk#5550)

* initial commit of budget96 * non logic changes * add my name to readme * update matrix.c * make the matrix representation of the layout macro * fix up LAYOUT macro * add missing character * initial keymap commit * put KC_NO where they belong * basic keymap * fix matrix row and col definition * The diagram I was sent and the pins used I was sent were in opposite order from each other. This should fix the issues * update the readme * change up manufacturer for budget96 * update copyright date * fix up the switch matrix and provide a keymap * forgot the keymap * other matrix fixes * missing a few keys in the switch matrix * messed up the row tracing * tweak keymap a bit * use a lower case k * fix spacing for markdown rendering * put in the reset key documentation * clean up the file a little * use LAYOUT_96_ansi * add a second layer for lighting controls * add in lighting support * add QMK Configurator support * use pragma once * remove un needed matrix.c * convert to GPIO methods * turn on rgblight_enable and get rid of custom matrix * set bootloadhid_bootloader to 1 * set bootmagic to lite and set it to k50 * add reset information to readme * use i2c_master instead of custom i2c * restore the custom i2c code * introduce reset key and eep_rst in function layer 1 * fix up pip3 install commands * fix up device and manufacturer names * remove un needed comments * add an ALL layout macro along with QMK Configurator support * move budget96 into donutcables directory since he actually has different boards * add a short donut cables blurb taken from his website * update readme for make instructions to point to the new path * Update keyboards/donutcables/budget96/config.h Co-Authored-By: mechmerlin <[email protected]> * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <[email protected]> * Update keyboards/donutcables/budget96/info.json Co-Authored-By: mechmerlin <[email protected]> * turn on backlight * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <[email protected]> * remove extra UART and BOOTLOADER settings that are not needed
foosinn · Apr 4, 2019 · f698f1e · f698f1e
1 parent 852d125
commit f698f1e
Show file tree

Hide file tree

Showing 13 changed files with 883 additions and 0 deletions.
diff --git a/keyboards/donutcables/budget96/budget96.c b/keyboards/donutcables/budget96/budget96.c
@@ -0,0 +1,80 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+ */
+#include "budget96.h"
+
+#ifdef BACKLIGHT_ENABLE
+#include "backlight.h"
+#endif
+#ifdef RGBLIGHT_ENABLE
+#include "rgblight.h"
+#endif
+
+#include <avr/pgmspace.h>
+
+#include "action_layer.h"
+#include "i2c.h"
+#include "quantum.h"
+
+__attribute__ ((weak))
+void matrix_scan_user(void) {
+}
+
+#ifdef RGBLIGHT_ENABLE
+extern rgblight_config_t rgblight_config;
+
+void rgblight_set(void) {
+ if (!rgblight_config.enable) {
+ for (uint8_t i = 0; i < RGBLED_NUM; i++) {
+ led[i].r = 0;
+ led[i].g = 0;
+ led[i].b = 0;
+ }
+ }
+
+ i2c_init();
+ i2c_send(0xb0, (uint8_t*)led, 3 * RGBLED_NUM);
+}
+#endif
+
+void backlight_init_ports(void) {
+ // initialize pins D0, D1, D4 and D6 as output
+ setPinOutput(D0);
+ setPinOutput(D1);
+ setPinOutput(D4);
+ setPinOutput(D6);
+
+ // turn RGB LEDs on
+ writePinHigh(D0);
+ writePinHigh(D1);
+ writePinHigh(D4);
+ writePinHigh(D6);
+}
+
+ void backlight_set(uint8_t level) {
+ if (level == 0) {
+ // turn RGB LEDs off
+ writePinLow(D0);
+ writePinLow(D1);
+ writePinLow(D4);
+ writePinLow(D6);
+ } else {
+ // turn RGB LEDs on
+ writePinHigh(D0);
+ writePinHigh(D1);
+ writePinHigh(D4);
+ writePinHigh(D6);
+ }
+ }
diff --git a/keyboards/donutcables/budget96/budget96.h b/keyboards/donutcables/budget96/budget96.h
@@ -0,0 +1,56 @@
+/* Copyright 2019 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+ */
+#pragma once
+
+#include "quantum.h"
+
+#define LAYOUT_all( \
+ k50, k52, k53, k54, k55, k60, k6A, k7A, k70, k5B, k5C, k5D, k5E, k1D, k2E, k0D, k76, k79, k78, \
+ k40, k41, k42, k43, k44, k45, k61, k6B, k7B, k71, k4A, k4B, k4C, k4D, k4E, k46, k47, k48, k49, \
+ k30, k31, k32, k33, k34, k35, k62, k6C, k7C, k72, k3A, k3B, k3C, k3D, k36, k37, k38, k39, \
+ k20, k21, k22, k23, k24, k25, k63, k6D, k7D, k73, k2A, k2B, k2C, k2D, k26, k27, k28, k29, \
+ k10, k03, k11, k12, k13, k14, k15, k64, k6E, k7E, k74, k1A, k1B, k68, k16, k17, k18, k19, \
+ k00, k01, k02, k65, k75, k0A, k0B, k66, k67, k69, k06, k08, k09 \
+) \
+{ \
+ { k00, k01, k02, k03, KC_NO, KC_NO, k06, KC_NO, k08, k09, k0A, k0B, KC_NO, k0D, KC_NO }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, k19, k1A, k1B, KC_NO, k1D, KC_NO }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, k2C, k2D, k2E }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k3D, KC_NO }, \
+ { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, k4D, k4E }, \
+ { k50, KC_NO, k52, k53, k54, k55, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, k5B, k5C, k5D, k5E }, \
+ { k60, k61, k62, k63, k64, k65, k66, k67, k68, k69, k6A, k6B, k6C, k6D, k6E }, \
+ { k70, k71, k72, k73, k74, k75, k76, KC_NO, k78, k79, k7A, k7B, k7C, k7D, k7E }, \
+}
+
+#define LAYOUT_96_ansi( \
+ k50, k52, k53, k54, k55, k60, k6A, k7A, k70, k5B, k5C, k5D, k5E, k1D, k2E, k0D, k76, k79, k78, \
+ k40, k41, k42, k43, k44, k45, k61, k6B, k7B, k71, k4A, k4B, k4C, k4E, k46, k47, k48, k49, \
+ k30, k31, k32, k33, k34, k35, k62, k6C, k7C, k72, k3A, k3B, k3C, k3D, k36, k37, k38, k39, \
+ k20, k21, k22, k23, k24, k25, k63, k6D, k7D, k73, k2A, k2B, k2D, k26, k27, k28, k29, \
+ k10, k11, k12, k13, k14, k15, k64, k6E, k7E, k74, k1A, k1B, k68, k16, k17, k18, \
+ k00, k01, k02, k65, k75, k0B, k66, k67, k69, k06, k08, k09 \
+) \
+{ \
+ { k00, k01, k02, KC_NO, KC_NO, KC_NO, k06, KC_NO, k08, k09, KC_NO, k0B, KC_NO, k0D, KC_NO }, \
+ { k10, k11, k12, k13, k14, k15, k16, k17, k18, KC_NO, k1A, k1B, KC_NO, k1D, KC_NO }, \
+ { k20, k21, k22, k23, k24, k25, k26, k27, k28, k29, k2A, k2B, KC_NO, k2D, k2E }, \
+ { k30, k31, k32, k33, k34, k35, k36, k37, k38, k39, k3A, k3B, k3C, k3D, KC_NO }, \
+ { k40, k41, k42, k43, k44, k45, k46, k47, k48, k49, k4A, k4B, k4C, KC_NO, k4E }, \
+ { k50, KC_NO, k52, k53, k54, k55, KC_NO, KC_NO, KC_NO, KC_NO, KC_NO, k5B, k5C, k5D, k5E }, \
+ { k60, k61, k62, k63, k64, k65, k66, k67, k68, k69, k6A, k6B, k6C, k6D, k6E }, \
+ { k70, k71, k72, k73, k74, k75, k76, KC_NO, k78, k79, k7A, k7B, k7C, k7D, k7E }, \
+}
diff --git a/keyboards/donutcables/budget96/config.h b/keyboards/donutcables/budget96/config.h
@@ -0,0 +1,47 @@
+/*
+Copyright 2017 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+*/
+
+#pragma once
+
+#include "config_common.h"
+
+#define VENDOR_ID 0x20A0
+#define PRODUCT_ID 0x422D
+#define MANUFACTURER DonutCables
+#define PRODUCT budget96
+
+#define RGBLED_NUM 16
+
+#define MATRIX_ROWS 8
+#define MATRIX_COLS 15
+
+#define MATRIX_COL_PINS { A0, A1, A2, A3, A4, A5, A6, A7, C7, C6, C5, C4, C3, C2, D7 }
+#define MATRIX_ROW_PINS { B0, B1, B2, B3, B4, B5, B6, B7 }
+#define UNUSED_PINS
+
+#define DIODE_DIRECTION COL2ROW
+#define DEBOUNCING_DELAY 5
+
+#define NO_BACKLIGHT_CLOCK
+#define BACKLIGHT_LEVELS 1
+#define RGBLIGHT_ANIMATIONS
+
+// Set bootmagic lite key to the key commonly programmed as Esc. 
+#define BOOTMAGIC_LITE_ROW 5
+#define BOOTMAGIC_LITE_COLUMN 0 
+
+/* key combination for command */
diff --git a/keyboards/donutcables/budget96/i2c.c b/keyboards/donutcables/budget96/i2c.c
@@ -0,0 +1,106 @@
+/*
+Copyright 2016 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+*/
+
+// Please do not modify this file
+
+#include <avr/io.h>
+#include <util/twi.h>
+
+#include "i2c.h"
+
+void i2c_set_bitrate(uint16_t bitrate_khz) {
+ uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
+ if (bitrate_div >= 16) {
+ bitrate_div = (bitrate_div - 16) / 2;
+ }
+ TWBR = bitrate_div;
+}
+
+void i2c_init(void) {
+ // set pull-up resistors on I2C bus pins
+ PORTC |= 0b11;
+
+ i2c_set_bitrate(400);
+
+ // enable TWI (two-wire interface)
+ TWCR |= (1 << TWEN);
+
+ // enable TWI interrupt and slave address ACK
+ TWCR |= (1 << TWIE);
+ TWCR |= (1 << TWEA);
+}
+
+uint8_t i2c_start(uint8_t address) {
+ // reset TWI control register
+ TWCR = 0;
+
+ // begin transmission and wait for it to end
+ TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ // check if the start condition was successfully transmitted
+ if ((TWSR & 0xF8) != TW_START) {
+ return 1;
+ }
+
+ // transmit address and wait
+ TWDR = address;
+ TWCR = (1<<TWINT) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ // check if the device has acknowledged the READ / WRITE mode
+ uint8_t twst = TW_STATUS & 0xF8;
+ if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
+ return 1;
+ }
+
+ return 0;
+}
+
+void i2c_stop(void) {
+ TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
+}
+
+uint8_t i2c_write(uint8_t data) {
+ TWDR = data;
+
+ // transmit data and wait
+ TWCR = (1<<TWINT) | (1<<TWEN);
+ while (!(TWCR & (1<<TWINT)));
+
+ if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
+ return 1;
+ }
+
+ return 0;
+}
+
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
+ if (i2c_start(address)) {
+ return 1;
+ }
+
+ for (uint16_t i = 0; i < length; i++) {
+ if (i2c_write(data[i])) {
+ return 1;
+ }
+ }
+
+ i2c_stop();
+
+ return 0;
+}
diff --git a/keyboards/donutcables/budget96/i2c.h b/keyboards/donutcables/budget96/i2c.h
@@ -0,0 +1,24 @@
+/*
+Copyright 2016 Luiz Ribeiro <[email protected]>
+
+This program is free software: you can redistribute it and/or modify
+it under the terms of the GNU General Public License as published by
+the Free Software Foundation, either version 2 of the License, or
+(at your option) any later version.
+
+This program is distributed in the hope that it will be useful,
+but WITHOUT ANY WARRANTY; without even the implied warranty of
+MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+GNU General Public License for more details.
+
+You should have received a copy of the GNU General Public License
+along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+*/
+
+// Please do not modify this file
+
+#pragma once
+
+void i2c_init(void);
+void i2c_set_bitrate(uint16_t bitrate_khz);
+uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length);
diff --git a/keyboards/donutcables/budget96/info.json b/keyboards/donutcables/budget96/info.json
@@ -0,0 +1,16 @@
+{
+ "keyboard_name": "budget96", 
+ "url": "", 
+ "maintainer": "qmk", 
+ "width": 19, 
+ "height": 6, 
+ "layouts": {
+ "LAYOUT_all": {
+ "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":16, "y":0}, {"x":17, "y":0}, {"x":18, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":12, "y":1}, {"x":13, "y":1}, {"x":14, "y":1}, {"x":15, "y":1}, {"x":16, "y":1}, {"x":17, "y":1}, {"x":18, "y":1}, {"x":0, "y":2, "w":1.5}, {"x":1.5, "y":2}, {"x":2.5, "y":2}, {"x":3.5, "y":2}, {"x":4.5, "y":2}, {"x":5.5, "y":2}, {"x":6.5, "y":2}, {"x":7.5, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2, "w":1.5}, {"x":15, "y":2}, {"x":16, "y":2}, {"x":17, "y":2}, {"x":18, "y":2}, {"x":0, "y":3, "w":1.75}, {"x":1.75, "y":3}, {"x":2.75, "y":3}, {"x":3.75, "y":3}, {"x":4.75, "y":3}, {"x":5.75, "y":3}, {"x":6.75, "y":3}, {"x":7.75, "y":3}, {"x":8.75, "y":3}, {"x":9.75, "y":3}, {"x":10.75, "y":3}, {"x":11.75, "y":3}, {"x":12.75, "y":3}, {"x":13.75, "y":3, "w":1.25}, {"x":15, "y":3}, {"x":16, "y":3}, {"x":17, "y":3}, {"x":18, "y":3}, {"x":0, "y":4, "w":1.25}, {"x":1.25, "y":4}, {"x":2.25, "y":4}, {"x":3.25, "y":4}, {"x":4.25, "y":4}, {"x":5.25, "y":4}, {"x":6.25, "y":4}, {"x":7.25, "y":4}, {"x":8.25, "y":4}, {"x":9.25, "y":4}, {"x":10.25, "y":4}, {"x":11.25, "y":4}, {"x":12.25, "y":4, "w":1.75}, {"x":14, "y":4}, {"x":15, "y":4}, {"x":16, "y":4}, {"x":17, "y":4}, {"x":18, "y":4}, {"x":0, "y":5, "w":1.25}, {"x":1.25, "y":5, "w":1.25}, {"x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"x":10, "y":5}, {"x":11, "y":5}, {"x":12, "y":5}, {"x":13, "y":5}, {"x":14, "y":5}, {"x":15, "y":5}, {"x":16, "y":5}, {"x":17, "y":5}, {"x":18, "y":5}]
+ },
+
+ "LAYOUT_96_ansi": {
+ "layout": [{"x":0, "y":0}, {"x":1, "y":0}, {"x":2, "y":0}, {"x":3, "y":0}, {"x":4, "y":0}, {"x":5, "y":0}, {"x":6, "y":0}, {"x":7, "y":0}, {"x":8, "y":0}, {"x":9, "y":0}, {"x":10, "y":0}, {"x":11, "y":0}, {"x":12, "y":0}, {"x":13, "y":0}, {"x":14, "y":0}, {"x":15, "y":0}, {"x":16, "y":0}, {"x":17, "y":0}, {"x":18, "y":0}, {"x":0, "y":1}, {"x":1, "y":1}, {"x":2, "y":1}, {"x":3, "y":1}, {"x":4, "y":1}, {"x":5, "y":1}, {"x":6, "y":1}, {"x":7, "y":1}, {"x":8, "y":1}, {"x":9, "y":1}, {"x":10, "y":1}, {"x":11, "y":1}, {"x":12, "y":1}, {"x":13, "y":1, "w":2}, {"x":15, "y":1}, {"x":16, "y":1}, {"x":17, "y":1}, {"x":18, "y":1}, {"x":0, "y":2, "w":1.5}, {"x":1.5, "y":2}, {"x":2.5, "y":2}, {"x":3.5, "y":2}, {"x":4.5, "y":2}, {"x":5.5, "y":2}, {"x":6.5, "y":2}, {"x":7.5, "y":2}, {"x":8.5, "y":2}, {"x":9.5, "y":2}, {"x":10.5, "y":2}, {"x":11.5, "y":2}, {"x":12.5, "y":2}, {"x":13.5, "y":2, "w":1.5}, {"x":15, "y":2}, {"x":16, "y":2}, {"x":17, "y":2}, {"x":18, "y":2}, {"x":0, "y":3, "w":1.75}, {"x":1.75, "y":3}, {"x":2.75, "y":3}, {"x":3.75, "y":3}, {"x":4.75, "y":3}, {"x":5.75, "y":3}, {"x":6.75, "y":3}, {"x":7.75, "y":3}, {"x":8.75, "y":3}, {"x":9.75, "y":3}, {"x":10.75, "y":3}, {"x":11.75, "y":3}, {"x":12.75, "y":3, "w":2.25}, {"x":15, "y":3}, {"x":16, "y":3}, {"x":17, "y":3}, {"x":18, "y":3}, {"x":0, "y":4, "w":2.25}, {"x":2.25, "y":4}, {"x":3.25, "y":4}, {"x":4.25, "y":4}, {"x":5.25, "y":4}, {"x":6.25, "y":4}, {"x":7.25, "y":4}, {"x":8.25, "y":4}, {"x":9.25, "y":4}, {"x":10.25, "y":4}, {"x":11.25, "y":4}, {"x":12.25, "y":4, "w":1.75}, {"x":14, "y":4}, {"x":15, "y":4}, {"x":16, "y":4}, {"x":17, "y":4}, {"x":0, "y":5, "w":1.25}, {"x":1.25, "y":5, "w":1.25}, {"x":2.5, "y":5, "w":1.25}, {"x":3.75, "y":5, "w":6.25}, {"x":10, "y":5, "w":1.5}, {"x":11.5, "y":5, "w":1.5}, {"x":13, "y":5}, {"x":14, "y":5}, {"x":15, "y":5}, {"x":16, "y":5}, {"x":17, "y":5}, {"x":18, "y":4, "h":2}]
+ }
+ }
+}
diff --git a/keyboards/donutcables/budget96/keymaps/default/config.h b/keyboards/donutcables/budget96/keymaps/default/config.h
@@ -0,0 +1,19 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+ */
+
+#pragma once
+
+// place overrides here
diff --git a/keyboards/donutcables/budget96/keymaps/default/keymap.c b/keyboards/donutcables/budget96/keymaps/default/keymap.c
@@ -0,0 +1,35 @@
+/* Copyright 2018 MechMerlin
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation, either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http:https://www.gnu.org/licenses/>.
+ */
+#include QMK_KEYBOARD_H
+
+const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = {
+[0] = LAYOUT_96_ansi(\
+ KC_ESC, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_PSCR, KC_NLCK, KC_INS, KC_HOME, KC_PGUP, KC_PSLS, \
+ KC_GRV, KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, KC_BSPC, KC_END, KC_PGDN, KC_PSLS, KC_PAST, \
+ KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, KC_P7, KC_P8, KC_P9, KC_PMNS, \
+ KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_ENT, KC_P4, KC_P5, KC_P6, KC_PPLS, \
+ KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSFT, KC_UP, KC_P1, KC_P2, KC_P3, \
+ KC_LCTL, KC_LGUI, KC_LALT, KC_SPC, KC_RALT, MO(1), KC_LEFT, KC_DOWN, KC_RIGHT, KC_P0, KC_PDOT, KC_PENT), \
+
+[1] = LAYOUT_96_ansi(\
+ RESET, EEP_RST, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ BL_TOGG, BL_STEP, BL_ON, BL_OFF, BL_INC, BL_DEC, BL_BRTG, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ RGB_TOG, RGB_MOD, RGB_HUI, RGB_SAI, RGB_VAI, RGB_SPI, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, RGB_RMOD, RGB_HUD, RGB_SAD, RGB_VAD, RGB_SPD, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, \
+ KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS, KC_TRNS), \
+};
+
diff --git a/keyboards/donutcables/budget96/keymaps/default/readme.md b/keyboards/donutcables/budget96/keymaps/default/readme.md
@@ -0,0 +1 @@
+# The default keymap for budget96