This library is meant for Arduino application using the Athena bootloader and storing data in the Arduino EEPROM.

The Athena bootloader requires space in the EEPROM. Devices which are also using the EEPROM can use the AthenaEEPROM library instead of the built-in EEPROM library. AthenaEEPROM will automatically handle offsets for Athena data, meaning that you do not need to adjust EEPROM offsets in your program.

If you are using the default EEPROM library for our own purposes, you must start writing after NETEEPROM_END, available in AthenaEEPROM_defs.h:

Note that use of the Athena bootloader does reduce the maximum available EEPROM capacity for the application by NETEEPROM_END-1 bytes.

In addition to reading and writing data from the EEPROM, this library also enables you to read/write network settings using the Arduino EEPROM. These network settings are used by the Athena bootloader and AthenaEthernetReset library.

You must program the device with the proper network settings in order for the Athena bootloader and AthenaEthernetReset library to properly function.

To use the library, include AthenaEEPROM.h instead of EEPROM.h:

#include <AthenaEEPROM.h>

The library provides a global instance called EEPROM that serves as a drop-in replacement for the standard EEPROM object provided by EEPROM.h.

The standard interfaces still work. You can write a byte with the write API:

EEPROM.write(addr, val);

And read a byte using the read API:

byte value = EEPROM.read(address);

This library automatically handles the offset that protects Athena-specific EEPROM data. The actual size of the EEPROM available to your program is reduced by NETEEPROM_OFFSET bytes, defined in AthenaEEPROM.h.

For more information on migrating an existing application that uses the EEPROM, see the migration guide.

This library uses the Arduino EEPROM to store values needed by the bootloader and AthenaEthernetReset server. If you are using the default EEPROM library for our own purposes, please make sure to start writing after NETEEPROM_END, available in AthenaEEPROM_defs.h.

If you use the AthenaEEPROM library included with the Athena bootloader, then offsets will be handled for you automatically.

A global instance is declared by the library and should be referenced within your application:

AthenaEEPROMClass AthenaEEPROM;

The current settings can be printed out to serial:

AthenaEEPROM.printAll(&Serial);

To update network settings, use the writeNet function:

byte  mac[] = {0x12, 0x34, 0x56, 0x78, 0x9A, 0xBC};
IPAddress  ip(192, 168, 1, 120);
IPAddress  gateway(192, 168, 1, 1);
IPAddress  subnet(255, 255, 255, 0);

/* Write the new settings values to EEPROM */
AthenaEEPROM.writeNet(mac, ip, gateway, subnet);

You can change the TFTP data transfer port from the default setting, if needed, by using writePort:

word port = 46969;

/* Set the TFTP data transfer port in EEPROM. Change it only if you need to. */
AthenaEEPROM.writePort(port);

You can change the AthenaEthernetReset URL "password" using the writePass function:

/* 
 * This is the "password" for the reset server in case you want to reset your Arduino
 * remotely. This setting has no effect on the bootloader itself. Password can be 36 characters
 * long, at maximum. Any string longer than 36 characters will be truncated.
 * Spaces should not be used 
 */
String password = "athena";

/* Write Reset Server password in EEPROM */
AthenaEEPROM.writePass(password);

You can manually set the programmed application image marker as "bad". In this case, the bootloader will think that there is no active application and will remain in bootloader mode until a new sketch is received:

/* Set image status to bad, so upon reboot the bootloader won't load the previous sketch */
AthenaEEPROM.writeImgBad();

Example sketches are provided:

1. ReadNetworkSettings
2. WriteNetworkSettings
3. eeprom_clear - demonstrates erasing all data from the EEPROM, except for Athena data
4. eeprom_read - demonstrates reading from the EEPROM
5. eeprom_write - demonstrates writing to the EEPROM

The ReadNetworkSettings sketch uses the AthenaEEPROM library to print out the currently configured network settings:

--- Network Settings ---
    MAC: 0xDE.0xAD.0xBE.0xEF.0xFE.0xED
Address: 10.0.1.199
Gateway: 10.0.1.1
 Subnet: 255.255.255.0
--- Tftp Settings ---
Data Port: 46969
(Default)
--- Reset Server Settings ---
Password: athena
  Length: 7
Settings read, you can now upload another sketch.

The WriteNetworkSettings sketch can be used to update the network settings for a device. Note that you must write network settings to the device before it can be properly used to update devices over Ethernet.