#This a library to be used in firmware for the ESP8266. This fork is change to work with Arduino xmasLED project. some changes to structure rgb

This library is a I2S Interface to drive WS2811/WS2812 and SK6812 LED strips. The code is lifted out of the esp-open-rtos project and has been modified to work with SK6812 LEDs and compile with the original Espressif RTOS SDK.

The communication with the LEDs is over I2S and uses DMA to offload timing critical stuff off the CPU. You will need a framebuffer (8bit per color) for each of your LEDs and the library internally needs DMA buffers which are 4 bytes per LED per color.

The I2S pin is shared with UART0 RxD so you will not be able to send anything to the ESP over serial anymore.

To select which type of LED you want to connect to your ESP module you may have to edit the Makefile:

CFLAGS      += -DLED_TYPE=LED_TYPE_WS2812 -DLED_MODE=LED_MODE_RGB

There are two possible values for LED_TYPE:

• LED_TYPE_WS2812 use this one for WS2811 or WS2812 LEDs
• LED_TYPE_SK6812 use this one for the SK6812 types (mostly used by RGBW strips)

This setting defines how many color components are in your LEDs

• LED_MODE_RGB this is the usual default, 3 colors. They are sent in GRB order.
• LED_MODE_RGBW use this if your LEDs have 4 color components, like the RGBW strips with a dedicated white LED in addition to the red, green and blue ones.

void ws2812_i2s_init(uint32_t pixels_number);

Call this one with the pixel count before starting to send out data. This will initalize all needed buffers and set the IOMUX for GPIO 3 from the default UART0 RxD to I2S.

void ws2812_i2s_update(ws2812_pixel_t *pixels);

Update the LED strip with new pixel data. The library assumes the number of pixels in this array are the same as with the init call.

One pixel looks like this:

typedef struct {
    uint8_t red;
    uint8_t green;
    uint8_t blue;
#if LED_MODE == LED_MODE_RGBW
    uint8_t white;
#endif
} ws2812_pixel_t;

so as you can see the white component is only available when configured for a RGBW strip.

This library is built with the esp8266-setup tool in mind.

If you are already using the esp8266-setup build system just issue the following command in your project dir:

esp8266-setup add-library git+https://github.com/esp8266-setup/ws2812_i2s.git@master

If you do not want to use the esp8266-setup build system just grab the files from the src and include directories and add them to your project.

Be aware that most libraries built with this build system use the C99 standard, so you may have to add --std=c99 to your CFLAGS.

• Install the ESP8266 Toolchain
• Download the ESP8266 RTOS SDK
• Compile the library:

    make \
      XTENSA_TOOLS_ROOT=/path/to/compiler/bin \
      SDK_PATH=/path/to/ESP8266_RTOS_SDK

• The finished library will be placed in the current directory under the name of libws2812-i2s.a
• Corresponding include files are in include/

If you installed the ESP SDK and toolchain to a default location (see below) you may just type make to build.

• XTENSA_TOOLS_ROOT: c:\ESP8266\xtensa-lx106-elf\bin
• SDK_PATH: c:\ESP8266\ESP8266_RTOS_SDK

We assume that your default file system is not case sensitive so you will have created a sparse bundle with a case sensitive filesystem which is named ESP8266:

• XTENSA_TOOLS_ROOT: /Volumes/ESP8266/esp-open-sdk/xtensa-lx106-elf/bin
• SDK_PATH: /Volumes/ESP8266/ESP8266_RTOS_SDK

• XTENSA_TOOLS_ROOT: /opt/Espressif/crosstool-NG/builds/xtensa-lx106-elf/bin
• SDK_PATH: /opt/Espressif/ESP8266_RTOS_SDK