Skip to content

alexmaul/AFD

 
 

Repository files navigation

--enable-maintainer_log              - This allows the maintainer to write
                                       additional large amount of debug
                                       log data to a log file. So this
                                       is only useful for the maintainer.
                                       [Default: disabled]
--enable-confirmation_log            - If you want to log all files names
                                       which need confirmation you have to
                                       enable this feature.
                                       [Default: disabled]
--enable-transfer_rate_log           - This writes the transfer rate into a
                                       separate log file TRANSFER_RATE_LOG.
                                       [Default: disabled]
--enable-systemd                     - Enables managing AFD via systemd.
                                       [Default: disabled]
--disable-input_log                  - If you want to log all files names
                                       on input you have to enable these
                                       features. But note that enabling this
                                       will pose a performance penalty,
                                       especially if the log files are
                                       very large.
                                       [Default: enabled]
--disable-distribution_log           - If you want to log all files
                                       distributed you have to enable
                                       these features. Note without this
                                       alda (AFD Log Data Analyzer) will
                                       not function properly.
                                       [Default: enabled]
--disable-production_log             - When enabled, this will make AFD log
                                       all files it renamed or where it
                                       changed its content.
                                       [Default: enabled]
--disable-output_log                 - If you want to log all files names on
                                       output you have to enable this
                                       feature. But note that enabling this
                                       will pose a performance penalty,
                                       especially if the log files are
                                       very large.
                                       [Default: enabled]
--disable-delete_log                 - If enabled, all files names that are
                                       deleted by the AFD get logged. They
                                       can then be viewed with show_dlog. But
                                       note that enabling this will pose a
                                       performance penalty, especially if
                                       lots of files get
                                       deleted.
                                       [Default: enabled]
--disable-ncurses_ui                 - Disables ncurses interface to AFD.
                                       [Default: enabled]
--disable-error_queue                - If enabled, AFD will queue error jobs
                                       so that this will not block jobs that
                                       work fine to another host.
                                       [Default: enabled]
--disable-loc_support                - Support for sending files locally.
                                       [Default: enabled]
--disable-ftp_support                - Support for the FTP protocol.
                                       [Default: enabled]
--disable-sftp_support               - Support for the SFTP protocol.
                                       [Default: enabled]
--disable-smtp_support               - Support for the SMTP protocol.
                                       [Default: enabled]
--disable-http_support               - Support for the HTTP protocol.
                                       [Default: enabled]
--disable-wmo_support                - Support for the special protocol used
                                       by the WMO to transport data via TCP.
                                       [Default: enabled]
--disable-fd_exec_support            - Support for using an external program
                                       to transmit the data.
                                       [Default: enabled]
--disable-ssl                        - Disable TLS/SSL support for the FTP and
                                       HTTP protocol.
                                       [Default: enabled]
--enable-atpd_support                - Enable support for the ATP daemon.
                                       ATP is AFD's own transfer protocol.
                                       [Default: disabled]
--disable-dupcheck_support           - When enabled AFD will be able to check
                                       the input and output for duplicates.
                                       [Default: enabled]
--disable-largefile                  - Large file support does not work
                                       properly on some older systems (linux
                                       2.2.x and earlier) and cause severe
                                       problems. So disable this when AFD
                                       does not start or you have very
                                       strange problems.
                                       [Default: enabled]
--disable-verify_fsa                 - When enabled, every time something is
                                       written to the FSA, it is checked
                                       whether it is correct. If not enabled
                                       you might see some incorrect numbers
                                       in the 'afd_ctrl' dialog. Though this
                                       is very seldom and if it does happen
                                       can be corrected with fsa_edit.
                                       [Default: enabled]
--disable-ignore_duplicate_jobs      - Duplicate jobs are ignored by AFD when
                                       this job is set. I cannot think of a
                                       good reason why one wants to disable
                                       this.
                                       [Default: enabled]
--disable-auto_create_config         - When during start AFD does not find a
                                       configuration it creates some default,
                                       so AFD does start.
                                       [Default: enabled]
--disable-afd_ctrl_proc_check        - By default the afd_ctrl dialog
                                       periodically checks if the process amg,
                                       fd, archive_watch and afdd are running.
                                       This check should be disabled on
                                       systems with shared filesystems
                                       and afd_ctrl being called from a node
                                       where AFD is not active.
                                       [Default: enabled]
--disable-fifo_rw_support            - Some systems do not support opening a
                                       FIFO for reading and writing. With
                                       this option set AFD will use two file
                                       descriptors one for reading and one
                                       for writing.
--disable-sse42                      - Disables SSE4.2 optimizations ie.
                                       support for hardware CRC-32 checksum
                                       calculation.
--disable-inotify                    - Disables inotify support.
--disable-new_motif_name             - Openmotif has been renamed to motif.
                                       To solve problems on distributions
                                       that still use openmotif provide
                                       this option to use the old name.
--enable-html_gui                    - Enable HTML GUI.
--enable-ip_database                 - Enable AFD's own internal IP database.
                                       This is only used when it fails lookup
                                       the IP from DNS.
--enable-ascii_only_subject          - Up to version 1.4.8-0.9.beta AFD
                                       accepted only 7 bit ASCII subjects
                                       for mail. Newer versions of AFD will
                                       encode the subject to base64 if it
                                       encounters a non 7 bit ASCII in the
                                       mail subject. So, setting this option
                                       will disable the automatic conversion
                                       and restore the original behaviour.
--enable-dfax_support                - Enable support for Divas Fax API
                                       for sending Fax. With the option
                                       --with-dfax-libraries=DIR one can
                                       specify the path and libraries.
--enable-map_support                 - Enable support for DWD's MAP weather
                                       visualisation tool. With the option
                                       --with-map-libraries=DIR one can
                                       specify the path and libraries.
--enable-de_mail_support             - Enables the special DE-mail support
                                       that is used in Germany.
--enable-report_empty_dir_scan       - Enables reporting of empty directory
                                       scans.
                                       [Default: disabled]
--enable-with_afdbench_settings      - Enables settings for running afdbench.
                                       [Default: disabled]
--enable-expand_path_in_message      - Enables expanding local relative path
                                       in message. Advantage of this option is
                                       that it will make AFD faster when it
                                       distributes files locally. Disadvantage
                                       is if a users home directory is changed
                                       it is not noticed by AFD, you then need
                                       to restart it.
                                       [Default: disabled]
--enable-statistics_in_fifodir       - Statistics are stored in fifodir.
                                       [Default: log directory]
--enable-with_archive_copy_info      - Inform when files are being copied
                                       instead of being moved in TRANSFER_LOG.
                                       [Default: disabled]
--enable-error_offline_for_new_host  - New host will have the flag
                                       'error + warnings offline' set.
--enable-setuid_progs                - Enables setting setuid flag for the
                                       programs afdcmd, afd, init_afd, mafd,
                                       afd_ctrl, dir_ctrl, mon_ctrl and
                                       show_olog.  The setuid flag is required
                                       if other users want to monitor or
                                       control the AFD, other then the user
                                       starting it. See also
                                       --enable-group_can_write.
                                       [Default: disabled]
--enable-with_unlink_delay           - Enable delay when unlinking a file and
                                       we get the error that the file is still
                                       busy. With this enabled it will make a
                                       short delay and then retry. This can be
                                       set when AFD is running on an NFS file-
                                       system.
                                       [Default: disabled]
--enable-multi_dir_scans             - Enable scanning of directories multiple
                                       times. This is needed on some systems
                                       where the modification time of
                                       directories scanned by AFD is not
                                       updated correctly. Normally it is not
                                       needed to set this.
                                       [Default: disabled]
--enable-multi_fs_support            - Enable AFD scanning multiple local
                                       filesystems without internal copying
                                       of data.
                                       [Default: disabled]
--enable-ftp_reuse_data_port         - Reuse the FTP data port when sending
                                       multiple files. This reduces the
                                       number of sockets in TIME_WAIT
                                       considerably. However it is dangerous
                                       to enable this since it can lead
                                       to data being lost on systems with
                                       broken TCP-stack. Note on some
                                       systems (darwin) it can slowdown the
                                       system considerably.
                                       [Default: disabled]
--enable-ms_error_workaround         - Enables workaround for a bug in M$
                                       Internet Information Server (IIS) FTP
                                       server when renaming files.
                                       [Default: disabled]
--enable-no_auto_basic_auth          - Since HTTPS digest authentication
                                       is hardly used by servers, AFD does
                                       by default do a preemptive basic
                                       authentication which saves a
                                       request/challenge cycle. With
                                       this option the user can disable
                                       this.
--enable-group_can_write             - The permissions of the fifos will have
                                       write access to the fifos. This can be
                                       used to allow users of the same group
                                       have access to the AFD of another user.
                                       See also --enable-setuid_progs.
                                       [Default: disabled]
--enable-lockdebug                   - All locks are logged to SYSTEM_LOG.
                                       This is only for debugging, so do not
                                       enable this.
                                       [Default: disabled]
--enable-show_exec_times             - Show exec times after rereading
                                       DIR_CONFIG.
                                       [Default: disabled]
--enable-sendfile_support            - Enables sendfile() support. This is
                                       more efficient then the usual
                                       combination of read() and write(),
                                       since copying is done within the
                                       kernel and no data needs to be
                                       copied from/to user space (zero copy).
                                       It has currently only been tested for
                                       linux.
                                       [Default: disabled]
--enable-splice_support              - Enables splice() support. When copying
                                       files the splice() system call is being
                                       used. splice() moves data between two
                                       file descriptors without copying
                                       between kernel address space and user
                                       address space.  splice() is only
                                       available for linux as of kernel 2.6.17
                                       (tested it only as of 2.6.23).
                                       [Default: disabled]
--enable-readyfile                   - Enables support for FSS ready files.
                                       Only used within the German Weather
                                       Service (DWD).
                                       [Default: disabled]
--enable-passwd_in_msg               - Write password in message file. This
                                       makes it a bit faster when you have
                                       to make lots of connections, since it
                                       does not need to always look into the
                                       password database.
                                       [Default: disabled]
--enable-eumetsat                    - Support to write EUMETSAT headers into
                                       each file send via FTP.
                                       [Default: disabled]
--enable-editres                     - This enables the dynamic resource editor
                                       for X Toolkit applications. This can be
                                       used to edit X resources if you do not
                                       like the defaults.
                                       [Default: disabled]
--enable-efence                      - Enables the electric fence debugger to
                                       debug AFD. Do not enable, it will make
                                       AFD very slow and eat lots of memory.
                                       [Default: disabled]
--enable-compile_afd_mon_only        - This will compile the AFD monitor only.
--enable-onetime_support             - Enables support for onetime jobs.
--enable-afd_mon                     - If set this will also compile all
                                       programms to monitor other AFD´s too.
                                       [Default: disabled]
--enable-compiler-debug              - Turns on debugging to debug AFD.
                                       [Default: disabled]
--enable-compiler-warn               - Turns on lots of warning when compiling.
                                       [Default: disabled]
--enable-compiler-analyzer           - Turns on gcc static analyzer.
--enable-compiler-optimizations      - Enables some compiler optimizations.
                                       [Default: disabled]
--enable-compiler-profiling          - Turns on compiler profiling support.
                                       [Default: disabled]
--enable-use_fortify                 - Turns on fortify option of glibc/gcc.
                                       Note this does not work with
                                       --enable-compiler-debug
                                       [Default: disabled]
--enable-compiler-security           - On gcc this will turn on the compiler
                                       option -pie (position independent
                                       executables) and -fstack-protector
                                       (check for buffer overflows).
                                       [Default: disabled]
--enable-compiler-address-sanitizer  - On gcc this will turn on the address
                                       sanitizer. Notice this will increase
                                       memory usage considerably.
                                       [Default: disabled]
--enable-compile-64-bit              - This forces AFD be compiled as 64 bit
                                       application on system that support both
                                       32 and 64 bit applications. On most 64
                                       bit systems it is not necessary to set
                                       this. This should only be used on
                                       systems that have both 32 and 64 bit
                                       and defaults to 32 bit.
                                       [Default: disabled]
--enable-with_ctrl_accelerator       - Use Ctrl key as accelerator key for X
                                       application.
--with-gui=motif|none                - Compile AFD with a certain graphical
                                       user interface.
                                       [Default: motif]
--enable-distro-rpm                  - Enables distribution style RPMS.
                                       [Default: disabled]
--with-initdir=INITDIR               - Directory where to put init/rc script
                                       to start/stop AFD. It is strongly
                                       recommended to NOT change this when
                                       using RPMS, since here we use
                                       chkconfig.
--with-sysconfigdir=SYSCONFIGDIR     - Directory where to put sysconfig files
                                       for AFD and AFDMON.
--with-rpm-binary-owner=OWNER        - Owner name of binaries in RPM.
                                       [Default: root]
--with-rpm-binary-group=GROUP        - Group name of binaries in RPM.
                                       [Default: OWNER]
--with-max-no-of-parallel-jobs=N     - Maximum number of parallel transfer per
                                       host alias. [Default: 9]
--with-default-no-of-parallel-jobs=N - Default number of parallel transfers
                                       per host alias. [Default: 3]
--with-default-archive-unit=N        - The default archive unit in seconds.
                                       [Default: 86400]
--with-max-hostname-length=N         - The maximum length that the host
                                       alias name may have in afd_ctrl
                                       dialog. [Default: 8]
--with-max-dir-alias-length=N        - The maximum length that the directory
                                       alias name may have. [Default: 10]
--with-max-afdname-length=N          - The maximum length that the AFD
                                       alias name may have in mon_ctrl
                                       dialog. [Default: 12]
--with-max-real-hostname-length=N    - The maximum length that the real
                                       hostname or IP may have. [Default: 70]
--with-max-recipient-length=N        - The maximum length that one recipient
                                       may have, including the directory
                                       entry. [Default 256]
--with-xor-key=KEY                   - With compiled in xor key KEY. Where
                                       KEY can be any ASCII string. If this
                                       is not set one needs to set the key
                                       in $AFD_WORK_DIR/etc/.xor.key.
                                       [Default: not set]

About

A tool to distribute data

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • C 98.1%
  • M4 1.2%
  • Other 0.7%