See "scripts" folder for Network Connection configuration

ROS1 (melodic/noetic) | ROS2 (rolling/humble/iron) | ROS2 (galactic/foxy)

ROS Version	Build Status (Linux)
ROS1 (melodic/noetic)
ROS2 (rolling/humble/iron)
ROS2 (galactic/foxy)

• Official ROS driver for Ouster sensors
  • Overview
  • Supported Devices
  • Requirements
    • Linux
    • Windows
    • Mac
  • Getting Started
  • Usage
    • Launching Nodes
      • Sensor Mode
      • Recording Mode
      • Replay Mode
      • Multicast Mode (experimental)
    • Invoking Services
      • GetMetadata
      • GetConfig
      • SetConfig
      • Reset
    • Driver Parameters
  • License

This ROS package provide support for all Ouster sensors with FW v2.0 or later targeting ros2 distros. Upon launch the driver will configure and connect to the selected sensor device, once connected the driver will handle incoming IMU and lidar packets, decode lidar frames and publish corresponding ROS messages on the topics of /ouster/imu and /ouster/points. In the case the used sensor supports dual return and it was configured to use this capability, then another topic will published under the name /ouster/points2 which corresponds to the second point cloud.

The driver supports the following list of Ouster sensors:

• OS0
• OS1
• OS2
• OSDome

You can obtain detailed specs sheet about the sensors and obtain updated FW through the website downloads section.

This branch is only intended for use with Rolling, Humble and Iron ROS 2 distros. Please refer to ROS 2 online documentation on how to setup ROS on your machine before proceeding with the remainder of this guide.

Note
If you have rosdep tool installed on your system you can then use the following command to get all required dependencies:
rosdep install --from-paths $OUSTER_ROS_PATH -y --ignore-src

In addition to the base ROS installation, the following ROS packages are required:

sudo apt install -y             \
    ros-$ROS_DISTRO-pcl-ros     \
    ros-$ROS_DISTRO-tf2-eigen   \
    ros-$ROS_DISTRO-rviz2

where $ROS_DISTRO can be either rolling, humble or iron.

Note
Installing ros-$ROS_DISTRO-rviz package is optional in case you didn't need to visualize the point cloud using rviz but remember to always set viz launch arg to false.

The following packages are also required

sudo apt install -y         \
    build-essential         \
    libeigen3-dev           \
    libjsoncpp-dev          \
    libspdlog-dev           \
    libcurl4-openssl-dev    \
    cmake                   \
    python3-colcon-common-extensions

Note
You may choose a different ssl backend for the curl library such as libcurl4-gnutls-dev or libcurl4-nss-dev

TBD

TBD

To build the driver using ROS2 you need to clone the project into the src folder of a ros2 workspace as shown below:

mkdir -p ros2_ws/src && cd ros2_ws/src
git clone -b ros2 --recurse-submodules https://github.com/ouster-lidar/ouster-ros.git

Next to compile the driver you need to source the ROS environemt into the active termainl:

source /opt/ros/<ros-distro>/setup.bash # replace ros-distro with 'rolling', 'humble', or 'iron'

Finally, invoke colcon build command from within the catkin workspace as shown below:

cd ros2_ws
colcon build --symlink-install --cmake-args -DCMAKE_BUILD_TYPE=Release

Note
Specifying Release as the build type is important to have a reasonable performance of the driver.

Once the build succeeds, you must source the install folder of your ros2 workspace to add launch commands to your environment:

source ros2_ws/install/setup.bash

The package supports three modes of interaction, you can connect to a live sensor, replay a recorded bag or record a new bag file using the corresponding launch files. Recently, we have added a new mode that supports multicast. The commands are listed below, for convenience we do provide both launch file formats (xml and python) but the python format is the preferred method:

To connect to a live sensor you use the following launch file

ros2 launch ouster_ros sensor.launch.xml    \
    sensor_hostname:=<sensor host name>

The equivalent python launch file is:

ros2 launch ouster_ros driver.launch.py    \
    params_file:=<path to params yaml file>

If you don't pass a params_file then the file located at ouster/config/driver_params.yaml will be used. Note that in the params you can start with default options for everything except the sensor_hostname param which you should adjust to match the hostname or ip address of the Ouster sensor you are trying to connect to.

comptability mode If you are migrating from https://github.com/ros-drivers/ros2_ouster_drivers to the official ouster drivers we supply you with a file driver_launch.py which provides users with same topic name and accepts the same parameter file community_driver_config.yaml. Please note that this is provided for backward compatibilty it may not be maintained in the future, so it would be better to update to the new format driver_params.yaml which offers the same options and more.

Note As of package version 8.1, specifiying metadata file is optional since the introduction of the metadata topic

ros2 launch ouster_ros record.launch.xml    \
    sensor_hostname:=<sensor host name>     \
    bag_file:=<optional bag file name>      \
    metadata:=<json file name>              # optional

Note As of package version 8.1, specifiying metadata file is optional if the bag file being replayed already contains the metadata topic

ros2 launch ouster_ros replay.launch.xml    \
    bag_file:=<path to rosbag file>         \
    metadata:=<json file name>              # optional if bag file has /metadata topic

The multicast launch mode supports configuring the sensor to broadcast lidar packets from the same sensor (live) to multiple active clients. You initiate this mode by using sensor_mtp.launch.xml file to start the node. You will need to specify a valid multicast group for the udp_dest argument which the sensor is going to broadcast data to it. You will also need to set mtp_main argument to true, this is need to configure the sensor with the specified udp_dest and any other sensor settings. You can control on which ip (IP4 only) you wish to receive the data on this machine from the multicast group using the mtp_dest argument as follows:

roslaunch ouster_ros sensor_mtp.launch.xml  \
    sensor_hostname:=<sensor host name>     \
    udp_dest:=<multicast group ip (ipv4)>   \
    mtp_main:=true                          \
    mtp_dest:=<client ip to receive data>   # mtp_dest is optional

Using a different machine that belongs to the same netwok subnet, you can start another instance of the client to start receiving sensor messages through the multicast group as shown below (note that mtp_main is set to false):

roslaunch ouster_ros sensor_mtp.launch.xml  \
    sensor_hostname:=<sensor host name>     \
    udp_dest:=<multicast group ip (ipv4)>   \
    mtp_main:=false                         \
    mtp_dest:=<client ip to receive data>   # mtp_dest is optional

Note: In both cases the mtp_dest is optional and if left unset the client will utilize the first available interface.

To execute any of the following service, first you need to open a new terminal and source the ros2 workspace again by running the command source ros2_ws/install/setup.bash

To get metadata while connected to a live sensor or during a replay session invoke the following command:

ros2 service call /ouster/get_metadata ouster_srvs/srv/GetMetadata

To get the current config of a live sensor, invoke the command:

ros2 service call /ouster/get_config ouster_srvs/srv/GetConfig

To change config via a file while connected to a live sensor, invoke the command:

ros2 service call /ouster/set_config ouster_srvs/srv/SetConfig \
    "{config_file: 'some_config.json'}"

To reset the new reset service, execute the following commnad:

ros2 service call /ouster/reset std_srvs/srv/Empty

When this service is invoked the client should stop streaming, dispose current connection, reset the sensor and reconnect again.

Note Changing settings is not yet fully support during a reset operation (more on this)

The driver has several parameters that allow you to customize its behavior, all of these parameters are defined with the driver_params.yaml file found under config folder. The only required parameter is sensor_hostname which sets the sensor hostname or ip that you want to connect to through ouster-ros driver.

Other notable parameters include:

• point_type: This parameter allows to customize the point cloud that the driver produces through its /ouster/points topics. Choose one of the following values:
  • original: This uses the original point representation ouster_ros::Point of the ouster-ros driver.
  • native: directly maps all fields as published by the sensor to an equivalent point cloud representation with the additon of ring and timestamp fields.
  • xyz: the simplest point type, only has {x, y, z}
  • xyzi: same as xyz point type but adds intensity (signal) field. this type is not compatible with the low data profile.
  • xyzir: same as xyzi type but adds ring (channel) field. this type is same as Velodyne point cloud type this type is not compatible with the low data profile.

This is not a comprehenisve list of all the parameters that the driver supports for more detailed list please refer to the config/driver_params.yaml file.

For further detailed instructions about the driver refer to the main guide

License File