Leer en Inglés, Español. Read in English, Spanish.
- WebSDR node based on a Raspberry PI
This WebSDR setup covers a dual band receiver (80/40 meters bands) time-based switched. It uses a relay to switch between antennas who is managed by one GPiO pin on the Raspberry PI (using a driver transistor).
Very special thanks to Pieter PA3FWM, Mark G4FPH and Jarek SQ9NFI for the helpful hand on configuring the progfreq setting.
- Raspberry PI 3 or greater.
- Raspberry Pi OS (Legacy) installed and working.
- Internet access setup and working
- RTL-SDR USB Dongle
sudo apt update && sudo apt upgrade
sudo apt install -y \
g++ \
make \
libsigc++-2.0-dev \
libgsm1-dev \
libpopt-dev \
tcl8.6-dev \
libgcrypt-dev \
libspeex-dev \
libasound2-dev \
alsa-utils \
libsigc++-2.0-0v5 \
cmake \
groff \
rtl-sdr \
libusb-1.0-0-dev \
unzip \
git \
rsync
cd /home/pi/
git clone https://github.com/reynico/raspberry-websdr.git
cd raspberry-websdr/
Over the time, some required libraries were deprecated in favor of newer and incompatible versions.
tar xf libpng-1.2.59.tar.xz
cd libpng-1.2.59/
./configure
make
sudo make install
cd ..
tar xf openssl-1.0.0k.tar.gz
cd openssl-1.0.0k/
cat << EOF > openssl.ld
OPENSSL_1.0.0 {
global:
*;
};
EOF
./config shared --prefix=$HOME/libssl/openssl --openssldir=$HOME/libssl/ssl -Wl,--version-script=openssl.ld -Wl,-Bsymbolic-functions
make
sudo make install_sw
sudo ldconfig
ldd $HOME/libssl/openssl/bin/openssl
sudo cp $HOME/libssl/openssl/lib/libcrypto.so /usr/local/lib
sudo chmod 0755 /usr/local/lib/libcrypto.so
sudo ldconfig
cd ..
If your SDR dongle supports direct sampling (such as RTL-SDR.com V3 receiver), there's a way to receive 500khz-28.8mhz without an external upconverter hardware, easing the node build.
unzip rtl-sdr-driver-patched.zip
cd pkg-rtl-sdr/
mkdir -p build/
cd build/
cmake ../ -DINSTALL_UDEV_RULES=ON -DDETACH_KERNEL_DRIVER=ON
make
sudo make install
sudo ldconfig
cd ../../
cp -r pkg-rtl-sdr/ /home/pi/
cd ..
Don't forget to remove the progfreq
line from the websdr configuration file(s).
Use the following systemd unit for direct sampling:
sudo cp etc/systemd/system/rtl_tcp_direct_sampling.service /etc/systemd/system/[email protected]
- This is a good time to reboot your Raspberry PI, do a
sudo reboot
. - Ask Pieter to get a copy of WebSDR.
- Copy the websdr-rpi binary and files to your home directory (/home/pi/)
- Edit websdr.cfg (for single band use), or websdr-80m.cfg and websdr-40m.cfg (for dual band use) to fulfill your configuration
- Create Systemd units to manage websdr and rtl_tcp
sudo cp etc/systemd/system/[email protected] /etc/systemd/system/[email protected]
Copy this systemd unit only if you're NOT using the RTL SDR direct sampling method
sudo cp etc/systemd/system/[email protected] /etc/systemd/system/[email protected]
The setup described in this section is the most usual: a single band SDR receiver (say, 40m band).
- Create systemd units to manage
websdr
andrtl_tcp
:
sudo cp etc/systemd/system/websdr.service /etc/systemd/system/websdr.service
- Enable the
rtl_tcp
systemd unit:
sudo systemctl enable [email protected]
- Enable the
websdr
unit:
sudo systemctl enable websdr.service
The setup described in this section is a more powerful one, where the Raspberry PI switches the WebSDR bands according to the time you define in crontab
.
This WebSDR setup uses one RTL-SDR dongle for two bands (40/80 meters), crontab takes control of which band is working. As wave length isn't the same on both two bands, I'm using a GPiO port to switch between them using a DPDT relay. GPIO3 is controlled by the check_band.sh cron script.
- Enable just the
rtl_tcp
systemd unit. Websdr is managed by crontab
sudo systemctl enable [email protected]
- I built a crontab configuration to switch between 40m and 80m bands time-based. Just import the crontab lines into your crontab.
You can always control band changes manual way. Disable cron lines to avoid automatic setup changes. Then you can use
sudo systemctl stop [email protected]
sudo systemctl start [email protected]
Where 40 is the band you want to receive. You can use and setup almost any band you want, as long as you had setup your websdr-{{band}}m.cfg
- Copy the etc/rc.local file to your /etc/rc.local
sudo cp etc/rc.local /etc/rc.local
- Check and match GPIO ports for relay control to switch antennas and a button to soft reset the Raspberry pi.
- There is a Python script that handles Raspberry PI reboots from a hardware switch without killing power.
- Check the /etc/rc.local file and match the desired GPIO port for this task.
- Copy etc/systemd/system/reset.service to /etc/systemd/system/reset.service
sudo cp opt/reset.py /opt/reset.py
sudo cp etc/systemd/system/reset.service /etc/systemd/system/reset.service
sudo chmod 644 /etc/systemd/system/reset.service
sudo systemctl enable reset.service
sudo systemctl start reset.service
This is the software reset schematic. It has a 5v pull-up signal between a 10k resistor.
You'll need to blacklist some modules in order to get rtl_tcp working. Edit or create the file /etc/modprobe.d/blacklist.conf
with the following content:
blacklist dvb_usb_rtl28xxu
To reduce the SD Card wear due to writes from logs, I recommend you to install log2ram, a tool which creates a ramdisk mountpoint for /var/log
.
echo "deb [signed-by=/usr/share/keyrings/azlux-archive-keyring.gpg] http:https://packages.azlux.fr/debian/ bookworm main" | sudo tee /etc/apt/sources.list.d/azlux.list
sudo wget -O /usr/share/keyrings/azlux-archive-keyring.gpg https://azlux.fr/repo.gpg
sudo apt update
sudo apt install log2ram
sudo systemctl enable log2ram
You may want to increase the ramdisk partition size up to 200M, edit the file /etc/log2ram.conf
and set SIZE=200M
.
While Websdr has an option to prevent logs to be written to the card (logfileinterval 0
), there are two log files that are written anyway: log-cpuload.txt
and userslog.txt
. Create a logs folder inside /var/log
and link both files in a symbolic fashion.
sudo rm /home/pi/dist11/userslog.txt
sudo rm /home/pi/dist11/log-cpuload.txt
sudo mkdir -p /var/log/websdr
ln -s /var/log/websdr/userslog.txt /home/pi/dist11/userslog.txt
ln -s /var/log/websdr/log-cpuload.txt /home/pi/dist11/log-cpuload.txt