Data Sheet

Version 1
Total pages 20
Date 2003.04.07
Product Specification
7〞 color TFT-LCD module
MODEL NAME: A070FW03
( ◆ ) Preliminary Specification
( … .. ) Final Specification
Note: The content of this © 2002 AU Optronics

specification is subject to All Rights Reserved,
change. Do Not Copy.
Record of Revision
Version Revise Date P a g e Content
0 07/Apr./2003 0 First draft.

Version : 1
Page : 1 /20
Contents:
A. Physical specification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P3
B. Electrical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P4
1. Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P4
a.TFT-LCD panel driving section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P4
b.Backlight driving section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P5
2.Absolute maximum ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P5
3. Electrical characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6
a. Typical operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6
b. Current consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6
c. Backlight driving conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6
4. AC Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P7
a. Timing conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P7
b. Timing diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P7
C. Optical specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P8
D. Reliability test items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P10
E. Packing form. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P11
ALL RIGHTS STRICTLY RESERVED. ANY PORTION OF THIS PAPER SHALL NOT BE REPRODUCED, COPIED, OR
TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM AU OPTRONICS CORP.
Version : 1
Page : 2 /20
Appendix:
Fig.1 Outline dimension of TFT-LCD module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P12
Fig.2 Sampling clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P14
Fig.3 Horizontal display timing range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P15
Fig.4-(a) Horizontal timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P16
Fig.4- (b) Detail horizontal timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P17
Fig.5 Vertical shift clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P18
Fig.6- (a) Vertical timing (From up to down). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P19
Fig.6-(b) Vertical timing (From down to up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P20
Version : 1
Page : 3 /20
A. Physical specifications
NO. Item Specification Remark
1 Display resolution(dot) 1440(W)×234(H)
2 Active area(mm) 154.08(W)×86.58(H)
3 Screen size(inch) 7.0(Diagonal)

4 Dot pitch(mm) 0.107(W)×0.370(H)
5 Color configuration R. G. B. stripe

6 Overall dimension(mm) 164.9(W)×100.0(H)×5.7(D) Note 1
7 Weight(g) 162 ±10
8 Surface treatment AG(5.5%) with WV film

9 Backlight unit CCFL
Note 1: Refer to Fig. 1
Version : 1
Page : 4 /20
B. Electrical specifications
1.Pin assignment
a. TFT-LCD panel driving section
Pin no Symbol I/O Description Remark
1 GND - Ground for logic circuit
2 VCC I Supply voltage of logic control circuit for scan driver
3 VGL I Negative power for scan driver
4 VGH I Positive power for scan driver
5 STVR I/O Vertical start pulse Note 1
6 STVL I/O Vertical start pulse Note 1
7 CKV I Shift clock input for scan driver
8 U/D I UP/DOWN scan control input Note 1,2
9 OEV I Output enable input for scan driver
10 VCOM I Common electrode driving signal
11 VCOM I Common electrode driving signal
12 L/R I LEFT/RIGHT scan control input Note 1,2
13 MOD I Sequential sampling and simultaneous sampling setting Note 3
14 OEH I Output enable input for data driver
15 STHL I/O Start pulse for horizontal scan line Note 1
16 STHR I/O Start pulse for horizontal scan line Note 1
17 CPH3 I Sampling and shifting clock pulse for data driver
20 VCC I Supply voltage of logic control circuit for data driver
21 GND - Ground for logic circuit
22 VR I Alternated video signal input(Red)
23 VG I Alternated video signal input(Green)
24 VB I Alternated video signal input(Blue)
25 AVDD I Supply voltage for analog circuit
26 AVSS - Ground for analog circuit
Note 1: Selection of scanning mode (please refer to the following table)

Setting of scan IN/OUT state
control input for start pulse Scanning direction
U/D L/R STVR STVL STHR STHL
GND VCC OUT IN OUT IN From up to down, and from left to right.
VCC GND IN OUT IN OUT From down to up, and from right to left.
GND GND OUT IN IN OUT From up to down, and from right to left.
VCC VCC IN OUT OUT IN From down to up, and from left to right.
IN: Input; OUT: Output.
Version : 1
Page : 5 /20
Note 2: Definition of scanning direction.
Refer to figure as below:
Note 3: MOD = H: Simultaneous sampling.

MOD = L: Sequential sampling.
Please set CPH2 and CPH3 to GND when MOD = H.
b. Backlight driving section (Refer to Figure 1)

No. Symbol I/O Description Remark
1 HI I Power supply for backlight unit (High voltage) --
2 GND - Ground for backlight unit --
2. Absolute maximum ratings

Item Symbol Condition Min. Max. Unit Remark
VCC GND=0 -0.3 7 V
AVDD AVSS=0 -0.3 7 V
Power voltage VGH -0.3 18 V
GND=0
VGL -15 0.3 V
VGH －VGL - 33 V
Vi -0.3 AVDD +0.3 V Note 1
Input signal voltage
VI -0.3 VCC +0.3 V Note 2
VCOM -2.9 5.2 V
Note 1: VR, VG, VB.
Note 2: STHL, STHR, OEH, L/R, CPH1~CPH3, STVR, STVL, OEV, CKV, U/D.
Version : 1
Page : 6 /20
3. Electrical characteristics
a. Typical operating conditions (GND=AVss=0V, Note 4 )
Item Symbol Min. Typ. Max. Unit Remark
VCC 3 5 5.2 V
AVDD 4.8 5 5.2 V
Power supply VGH 14.3 15 15.7 V
VGL -10.5 -10 -9.5 V
Video signal ViA 0.4 - AVDD -0.4 V Note 1
amplitude ViAC - 3 - V AC component
(VR,VG,VB)
ViDC - AVDD /2 - V DC component
VCAC 3.5 5.6 6.5 Vp-p AC component, Note 2
VCOM
VCDC 1.4 1.7 2.0 V DC component
Input H Level VIH 0.8 VCC - VCC V
signal Note 3
voltage L Level VIL 0 - 0.2 VCC V
Note 1: Refer to Fig.4- (a).
Note 2: The brightness of LCD panel could be changed by adjusting the AC component of
VCOM.
Note 3: STHL, STHR, OEH, L/R, CPH1~CPH3, STVR, STVL, OEV, CKV, U/D.
Note 4: Be sure to apply GND, VCC and VGL to the LCD first, and then apply VGH .
b. Current consumption (GND=AVss=0V)
Parameter Symbol Condition Min. Typ. Max. Unit Remark
Current IGH VGH =15V - 0.20 0.5 mA
for IGL VGL=-10V - 0.80 1.5 mA
driver
ICC VCC =5V - 3.0 6.0 mA
IDD AVDD =5V - 17.0 30 mA
c. Backlight driving conditions

Parameter Symbol Min. Typ. Max. Unit Remark
Lamp voltage VL - 560 620 Vrms
Lamp current IL - 6 7 mArms
Frequency FL - 60 80 kHz Note 4
- - 900 Vrms Note 1,5
Lamp starting voltage VS
- - - Vrms Note 2,5
- - 1,100 Vrms Note 3,5
Lamp life time 10,000 - - Hr Note 6
Note 1: Ta = 25℃ .
Note 2: Ta = 0℃ .
Note 3: Ta = -30℃ .
Note 4: The lamp frequency should be selected as different as possible from display
horizontal synchronous signal to avoid interference.
Note 5: For starting the backlight unit, the output voltage of DC/AC’s transformer should be larger
than the maximum lamp starting voltage.
Note 6: The” Lamp life time” is defined as the module brightness decrease to 50% original
brightness at Ta=25℃ , IL =6mA.
Version : 1
Page : 7 /20
5. AC Timing
a. Timing conditions
Parameter Symbol Min. Typ. Max. Unit. Remark
Rising time tr - - 10 ns Note 1
Falling time tf - - 10 ns Note 1
High and low level pulse width
tCPH 99 103 107 ns CPH1~CPH3
CPH pulse duty tCWH 40 50 60 % CPH1~CPH3

tC12
CPH pulse delay tC23 30 tCPH /3 tCPH /2 ns CPH1~CPH3
tC31
STH setup time tSUH 20 - - ns STHR,STHL
STH hold time tHDH 20 - - Ns STHR,STHL
STH pulse width tSTH - 1 - tCPH STHR,STHL
STH period tH 61.5 63.5 65.5 μs STHR,STHL
OEH pulse width tOEH - 1.22 - μs OEH
Sample and hold disable time tDIS1 - 8.28 - μs
OEV pulse width tOEV - 5.40 - μs OEV
CKV pulse width tCKV - 4.18 - μs CKV
Clean enable time tDIS2 - 3.74 - μs
Horizontal display start tSH - 0 - TCPH /3
Horizontal display
tDH - 1440 - TCPH /3
timing range
STV setup time tSUV 400 - - ns STVL,STVR
STV hold time tHDV 400 - - ns STVL,STVR
STV pulse width tSTV - - 1 tH STVL,STVR
Horizontal lines per field tV 256 262 268 tH Note 2
Vertical display start tSV 3 - tH
Vertical display timing range tDV 234 - tH
VCOM rising time trCOM - 5 μs
VCOM falling time tf COM - 5 μs
VCOM delay time tDCOM - 3 μs
RGB delay time tDRGB - 1 μs
Note 1: For all of the logic signals.
Note 2: Please don’t use odd horizontal lines to drive LCD panel for both odd and even field
simultaneously.
b. Timing diagram
Please refer to the attached drawing, from Fig.2 to Fig.6.
Version : 1
Page : 8 /20
5. Power Sequence
Sequence for power on/off and Signal on/off
Power on Power off

VGH VGH
VCC VCC VCC
GND GND
VGL VGL
T1
T5 T5
T1 T2
T7
T4 T6
T3
Video Signal, Logic Signal
OFF OFF
ON
T1 ≦ 15ms (From 10%*VCC to 90%*VCC，when VCC is Low to High)；

T2 ≦ 10ms (From 90%*VCC to 10%*VGH，when VCC is Low to High)；
T3 ≦ 10ms (From 90%*VGH to Video signal，when VGH is Low to High)；
T4 ≦ 10ms (From Video signal to 90%*VGH，when VGH is High to Low)；
T5 ≦ 20ms (From 90%*VCC to 10%*VCC，when VCC is High to Low)；
T6 ≦ 10ms (From 10%*VGH to 90%*VCC，when VCC is Low to High)；
T7 ≧ 0.4s (From 10%*VCC is H→L to 10%*VCC is L→H)。
Version : 1
Page : 9 /20
C. Optical specification (Note 1, Note 2)
Item Symbol Condition Min. Typ. Max. Unit Remark
Rise Tr θ=0° - 12 24 ms Note 3,5

Response time
Fall Tf - 18 36 ms
At optimized 200 300 - Note 4, 5

Contrast ratio CR
Viewing angle
Viewing angle Top 30 40 - Note 5, 6

Bottom 50 60 -
CR≧10 deg.
Left 50 60 -
Right 50 60 -
Viewing angle Top 30 50 - Note 5, 6

Bottom 60 70 -
CR≧5 deg.
Left 60 70 -
Right 60 70 -
2
Brightness YL IL=6mA, 25℃ 400 500 - cd/m Note 7
2
IL=6mA, -10℃, TBD TBD cd/m
after turn-on 1min
X θ=0° 0.26 0.31 0.36 Note 7

White chromaticity
Y θ=0° 0.28 0.33 0.38
Note 1 : Ambient temperature =25℃, and lamp current IL = 6 mArms. To be measured in the dark
room.
Note 2 :To be measured on the center area of panel with a viewing cone of 1° by Topcon
luminance meter BM-5, after 10 minutes operation.
Note 3. Definition of response time:
The output signals of photo detector are measured when the input signals are changed
from “black” to “white”(falling time) and from “white” to “black”(rising time), respectively.
The response time is defined as the time interval between the 10% and 90% of
amplitudes. Refer to figure as below.
"Black"
"White" "White"
100%
Signal(Relative value)
90%
10%
0% Tr Tf
Version : 1
Page : 10 /20
Note 4. Definition of contrast ratio:
Contrast ratio is calculated with the following formula.
Photo detector output when LCD is at “White” state

Contrast ratio (CR)=
Photo detector output when LCD is at “Black” state
Note 5. White Vi=Vi50 ＋ 1.5V

Black Vi=Vi50 ±2.0V
“±” means that the analog input signal swings in phase with VCOM signal.
“ ” means that the analog input signal swings out of phase with VCOM signal.
Vi50 : The analog input voltage when transmission is 50%
The 100% transmission is defined as the transmission of LCD panel when all the input
terminals of module are electrically opened.
Note 6. Definition of viewing angle, Refer to figure as below.
Note 7. Measured at the center area of the panel when all the input terminals of LCD panel are
electrically opened.
Version : 1
Page : 11 /20
D. Reliability test items(Note 2):
No. Test items Conditions Remark
1 High temperature storage Ta= 95℃ 240Hrs
2 Low temperature storage Ta= -40℃ 240Hrs
3 High temperature operation Ta= 85℃ 240Hrs
4 Low temperature operation Ta= -30℃ 240Hrs
5 High temperature and high humidity Ta= 60℃, 90% RH 240Hrs Operation
6 Heat shock -30℃~85℃/200 cycles 1Hrs/cycle Non-operation
±200V,200pF(0Ω), once for each terminal

7 Electrostatic discharge Non-operation
Frequency range : 8~33.3Hz

Stoke : 1.3mm JIS C7021,
8 Vibration Sweep : 2.9G, 33.3 ~ 400Hz A-10
Cycle : 15 minutes Condition A
2 hours for each direction of X,Z

4 hours for Y direction
100G, 6ms, ±X,±Y,±Z JIS C7021,
A-7
9 Mechanical shock 3 times for each direction Condition C
Random vibration:
2
10 Vibration (with carton) 0.015G /Hz from 5~200Hz IEC 68-34
–6dB/octave from 200~500Hz
Height: 60cm
11 Drop (with carton) JIS Z0202
1 corner, 3 edges, 6 surfaces
Note1: Ta: Ambient temperature.
Note 2: In the standard conditions, there is not display function NG issue occurred. All the
cosmetic specification is judged before the reliability stress.
Version : 1
Page : 12 /20
E. Packing form
TBD
Version : 1
Page : 13 /20
Fig.1-(a) Outline dimension of TFT-LCD module(Front side)
Version : 1
Page : 14 /20
Fig.2 Sampling clock timing

t C31
t C23
t HDH
t C12
t STH
t SUH
10%
tf
90% 90%
t CPH
50%
tr
t CWH
10%
50%
CPH2
STHL(R)
CPH1
CPH3
Version : 1
Page : 15 /20
Fig.3 Horizontal display timing range

t DH
Output(STHR/STHL)
Input(STHL/STHR)
CPH1
Version : 1
Page : 16 /20
Fig.4-(a) Horizontal timing

White
CAC
V
Black
Blank
White
V iAC
H
t
ViA
1H
Black
Blank
CDC
ViDC
V
V R(GB)
OEH
(HSY)
VCOM
CKV
STHL(R)
OEV
1H
(HSY)
OEH
t OEH t DIS1 t STH
STHL(R)
t OEV
OEV
t DIS2 t CKV
CKV
t DCOM
90% 90%
50%
10% 10%
VCOM
t rCOM t fCOM
Page
V R(GB)
Version
t DRGB

: 1
Note: The falling edge of OEV should be synchronized with the falling edge of OEH
: 17 /20
Fig.4-(b) Detail horizontal timing
Version : 1
Page : 18 /20
50%
Fig.5 Vertical shift clock timing

t CKV
t HDV
t SUV
50%
STVL(R)
CKV
Version : 1
Page : 19 /20
Fig.6-(a) Vertical timing (From up to down)

t SV
Display on panel first line
VR(GB)
(VSY)
(HSY)
STVL
VCOM(Even field)
VCOM(Odd field)
Version : 1
Page : 20 /20
Fig.6-(b) Horizontal timing (From down to up)

t SV
Display on panel first line
(HSY)
VCOM(Odd field)
VCOM(Even field)
V R(GB)
STVL
(VSY)

Data Sheet

Uploaded by

Copyright:

Available Formats

Data Sheet

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Data Sheet

Uploaded by

Copyright:

Available Formats

Version 1

Note: The content of this © 2002 AU Optronics

0 07/Apr./2003 0 First draft.

a.TFT-LCD panel driving section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P4

b.Backlight driving section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P5

2.Absolute maximum ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P5

a. Typical operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6

c. Backlight driving conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P6

D. Reliability test items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P10

E. Packing form. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P11

2 Active area(mm) 154.08(W)×86.58(H)

3 Screen size(inch) 7.0(Diagonal)

5 Color configuration R. G. B. stripe

7 Weight(g) 162 ±10

8 Surface treatment AG(5.5%) with WV film

Note 1: Selection of scanning mode (please refer to the following table)

Note 3: MOD = H: Simultaneous sampling.

b. Backlight driving section (Refer to Figure 1)

2. Absolute maximum ratings

c. Backlight driving conditions

CPH pulse duty tCWH 40 50 60 % CPH1~CPH3

Power on Power off

VCC VCC VCC

T1 ≦ 15ms (From 10%*VCC to 90%*VCC，when VCC is Low to High)；

Rise Tr θ=0° - 12 24 ms Note 3,5

At optimized 200 300 - Note 4, 5

Viewing angle Top 30 40 - Note 5, 6

Viewing angle Top 30 50 - Note 5, 6

X θ=0° 0.26 0.31 0.36 Note 7

Photo detector output when LCD is at “White” state

Note 5. White Vi=Vi50 ＋ 1.5V

Note 6. Definition of viewing angle, Refer to figure as below.

1 High temperature storage Ta= 95℃ 240Hrs

2 Low temperature storage Ta= -40℃ 240Hrs

3 High temperature operation Ta= 85℃ 240Hrs

4 Low temperature operation Ta= -30℃ 240Hrs

6 Heat shock -30℃~85℃/200 cycles 1Hrs/cycle Non-operation

±200V,200pF(0Ω), once for each terminal

Frequency range : 8~33.3Hz

2 hours for each direction of X,Z

Fig.1-(a) Outline dimension of TFT-LCD module(Front side)

Fig.2 Sampling clock timing

Fig.3 Horizontal display timing range

Fig.4-(a) Horizontal timing

t OEH t DIS1 t STH

TRANSFORMED TO ANY OTHER FORMS WITHOUT PERMISSION FROM AU OPTRONICS CORP.

Fig.5 Vertical shift clock timing

Fig.6-(a) Vertical timing (From up to down)

Fig.6-(b) Horizontal timing (From down to up)

You might also like

T1 ≦ 15ms (From 10%VCC to 90%VCC，when VCC is Low to High)；