Acid-Base Indicators For Use in Titration

Acid-Base Indicators
Certain organic substances change colour in dilute solution when the hydronium ion
concentration reaches a particular value. For example, phenolphthalein is a colourless
substance in any aqueous solution with a hydronium ion concentration greater than
5.0 × 10−9 M (pH < 8.3). In more basic solutions where the hydronium ion concentration
is less than 5.0 × 10−9 M (pH > 8.3), it is red or pink. Substances such as
phenolphthalein, which can be used to determine the pH of a solution, are called
acid-base indicators. Acid-base indicators are either weak organic acids or weak
organic bases.
The equilibrium in a solution of the acid-base indicator methyl orange, a weak acid, can
be represented by an equation in which we use HIn as a simple representation for the
complex methyl orange molecule:
HIn(aq) +H2O(l) ⇌ H3O+(aq) +In−(aq) (17.3.1
red )
yellow
[H3O+][In−] −4
Ka = = 4.0×10 (17.3.2
[HIn] )
−
The anion of methyl orange, In , is yellow, and the non ionized form, HIn, is red. When
we add acid to a solution of methyl orange, the increased hydronium ion concentration
shifts the equilibrium toward the non ionized red form, in accordance with Le
Chatelier’s principle. If we add base, we shift the equilibrium towards the yellow form.
This behaviour is completely analogous to the action of buffers.
An indicator’s colour is the visible result of the ratio of the concentrations of the two
species In− and HIn. If most of the indicator (typically about 60−90% or more) is
present as In−, then we see the colour of the In− ion, which would be yellow for methyl
orange. If most is present as HIn, then we see the colour of the HIn molecule: red for
methyl orange. For methyl orange, we can rearrange the equation for Ka and write:
[In−] [substance with yellow colour] Ka [HIn] [substance with red colour]
[H3O+]
= =
(17.3.3)
This shows us how the ratio of varies with the concentration of hydronium ion.
The above expression describing the indicator equilibrium can be rearranged:
[H3O+]
[HIn]
(17.3.4)
=
Ka [In−]
log [H3O+]) = log( [HIn]) (17.3.5) Ka
[In−]
[In−]
log([H3O+])−log(Ka) = −log( ) (17.3.6)
[HIn]
−
[In ]
−pH+pKa = −log( ) (17.3.7)
[HIn]
(
[In−] [base] [HIn] [acid]

pH = pKa +log ) or pH = pKa +log( ) (17.3.8)
The last formula is the same as the Henderson-Hassel Balch equation, which can be
used to describe the equilibrium of indicators.
When [H3O+] has the same numerical value as Ka, the ratio of [In−] to [HIn] is equal to 1,
meaning that 50% of the indicator is present in the red form (HIn) and 50% is in the
yellow ionic form (In−), and the solution appears orange in colour . When the
hydronium ion concentration increases to 8 × 10−4 M (a pH of 3.1), the solution turns
red. No change in colour is visible for any further increase in the hydronium ion
concentration (decrease in pH). At a hydronium ion concentration of 4 × 10−5 M (a pH of
4.4), most of the indicator is in the yellow ionic form, and a further decrease in the
hydronium ion concentration (increase in pH) does not produce a visible colour
change. The pH range between 3.1 (red) and 4.4 (yellow) is the colour -change interval
of methyl orange; the pronounced colour change takes place between these pH
values.
Many different substances can be used as indicators, depending on the particular
reaction to be monitored. For example, red cabbage juice contains a mixture of
coloured substances that change from deep red at low pH to light blue at intermediate
pH to yellow at high pH (Figure 17.3.1). In all cases, though, a good indicator must have
the following properties:
The colour change must be easily detected.
The colour change must be rapid.
The indicator molecule must not react with the substance being titrated.
To minimize errors, the indicator should have a pKin that is within one pH unit of the
expected pH at the equivalence point of the titration.
Figure 17.3.1: Naturally Occurring pH Indicators in Red Cabbage Juice. Image courtesy
of Wikipedia.
Red cabbage juice contains a mixture of substances whose colour depends on the pH.
Each test tube contains a solution of red cabbage juice in water, but the pH of the
solutions varies from pH = 2.0 (far left) to pH = 11.0 (far right). At pH = 7.0, the solution
is blue.
Synthetic indicators have been developed that meet these criteria and cover virtually
the entire pH range. Figure 17.3.2 shows the approximate pH range over which some
common indicators change colour and their change in colour . In addition, some
indicators (such as thymol blue) are polyprotic acids or bases, which change colour
twice at widely separated pH values.
Figure 17.3.2: Some Common Acid–Base Indicators. Approximate colour s are
shown, along with pKin values and the pH range over which the colour changes.
It is important to be aware that an indicator does not change colour abruptly at a
particular pH value; instead, it actually undergoes a pH titration just like any other acid
or base. As the concentration of HIn decreases and the concentration of In− increases,
the colour of the solution slowly changes from the characteristic colour of HIn to that
of In−. As we will see in Section 16, the [In−]/[HIn] ratio changes from 0.1 at a pH one
unit below pKin to 10 at a pH one unit above pKin. Thus most indicators change colour
over a pH range of about two pH units.
We have stated that a good indicator should have a pKin value that is close to the
expected pH at the equivalence point. For a strong acid–strong base titration, the
choice of the indicator is not especially critical due to the very large change in pH that
occurs around the equivalence point. In contrast, using the wrong indicator for a
titration of a weak acid or a weak base can result in relatively large errors, as illustrated
in Figure 17.3.3. This figure shows plots of pH versus volume of base added for the
titration of 50.0 mL of a 0.100 M solution of a strong acid (HCl) and a weak acid (acetic
acid) with 0.100 M NaOH. The pH ranges over which two common indicators (methyl
red, pKin = 5.0, and phenolphthalein, pKin = 9.5) change colour are also shown. The
horizontal bars indicate the pH ranges over which both indicators change colour cross
the HCl titration curve, where it is almost vertical. Hence both indicators change colour
when essentially the same volume of NaOH has been added (about 50 mL), which
corresponds to the equivalence point. In contrast, the titration of acetic acid will give
very different results depending on whether methyl red or phenolphthalein is used as
the indicator. Although the pH range over which phenolphthalein changes colour is
slightly greater than the pH at the equivalence point of the strong acid titration, the
error will be negligible due to the slope of this portion of the titration curve. Just as
with the HCl titration, the phenolphthalein indicator will turn pink when about 50 mL
of NaOH has been added to the acetic acid solution. In contrast, methyl red begins to
change from red to yellow around pH 5, which is near the midpoint of the acetic acid
titration, not the equivalence point. Adding only about 25–30 mL of NaOH will
therefore cause the methyl red indicator to change colour , resulting in a huge error.
In general, for titrations of strong acids with strong bases (and vice versa), any
indicator with a pK in between about 4.0 and 10.0 will do. For the titration of a weak
acid, however, the pH at the equivalence point is greater than 7.0, so an indicator such
as phenolphthalein or thymol blue, with pKin > 7.0, should be used. Conversely, for the
titration of a weak base, where the pH at the equivalence point is less than 7.0, an
indicator such as methyl red or bromocresol blue, with pKin < 7.0, should be used.
orange and bromocresol green change colour in an acidic pH range, while

phenolphthalein changes in a basic pH.
The existence of many different indicators with different colour s and pKin values also
provides a convenient way to estimate the pH of a solution without using an expensive
electronic pH meter and a fragile pH electrode. Paper or plastic strips impregnated with
combinations of indicators are used as “pH paper,” which allows you to estimate the
pH of a solution by simply dipping a piece of pH paper into it and comparing the
resulting colour with the standards printed on the container
Summary
Acid–base indicators are compounds that change colour at a particular pH. They are
typically weak acids or bases whose changes in colour correspond to deprotonation or
protonation of the indicator itself.
J&K Sainik School Manasbal
Chemistry Project
Topic: To study the uses of indicators in

acid-base titration
Submitted by: Sharik Naseer

Submitted to: Abdul Hamid Bhat
(PGT Chemistry)

Acid-Base Indicators For Use in Titration

Uploaded by

Copyright:

Available Formats

Acid-Base Indicators For Use in Titration

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Acid-Base Indicators For Use in Titration

Uploaded by

Copyright:

Available Formats

Acid-Base Indicators

[In−] [base] [HIn] [acid]

orange and bromocresol green change colour in an acidic pH range, while

Topic: To study the uses of indicators in

Submitted by: Sharik Naseer

You might also like