Worm Gear Boxes PDF

Products | Solutions | Service
Worm Gear Boxes Chapter 7

We hereby reserve the right to change content of data in this catalogue at any time without notice.
Our company shall not be held responsible for neither possible discrepancies in catalogue content nor any
damage caused by wrong use of products or information. Lönne Scandinavia AS reserves the prohibition to
publish pages or whole parts of this catalogue without authorization. All product names occurring or referred to
in this catalogue are or may be registered trademarks belonging to their respective producers or trademark owners.
The dimensions are in mm.
Illustrations are not binding.
Index
Page
General Product Overview 5

Single Worm Gear Boxes 030 - 110 12
Single Worm Gear Boxes with Spur Gear P45 - P10 26
Combined Worm Gear Unit 303 - 115 38
Product News, Square Worm Gear Boxes 56
Product News High Tech Worm Gear Boxes 57
Product News Stainlessteel Worm and Coaxial Gear Boxes 58
Appendix
Important addresses and phone numbers. General info. 59
3
Worm Gear Boxes Product Spectre
WORM Size 030 - 110 Single stage worm gearboxes. A simple

and economical solution for most
GEARBOX industrial application. Size 30 - 85
Torque : 20 - 620 Nm delivered with aluminium housing and oil.
Size 110 delivered in cast iron and without
oil. Stainless steel hubs are availible for all
Output hollow shaft : 14 - 42 mm sizes.
Ratio : 5 - 102
Single stage unit with helical primary

Size : P45 - P10 reduction at input.
WORM
Torque : 50 - 730 Nm
GEARBOX
Output hollow shaft : 18 - 42 mm
PRIMARY
Ratio : 29.9 - 624
REDUCTION
Two single stage units combined together.

COMBINED Size : 303 - 115
WORM Torque : 30 - 850 Nm
Output hollow shaft : 14 - 42 mm

GEARBOX
Ratio : 140 - 3000
5
Construction Description
A modular and compact product
Single piece alloy steel

input shaft and worm shaft.
Single- piece aluminum alloy housing High helix angle worm is
Is vacuum impregnated (MIL- STD 276) case- hardened (Rc 58-60),
for protection and sealing. ground, teeth are profiled
No secondary finish required but readily and radiused, for noise
accepts paint. Combines light weight with reduction and enhanced
high tensile strength. Precision machined efficiency.
for alignment of bearings and gearing.
Flange
Fully modular to IEC
and compact integrated Oversized bearings
motor. Support positively- retained,
NEMA C flange. high speed shaft for higher
shock load capacity - ideal
for frequent starting and
reversing application.
Premium, Nitrile® high
temperature seals each end.
Premium, high
temperature Bronze alloy worm gears.
Nitrile® output seals Is centrifugally cast onto an
iron hub for maximum
strenght and superior life.
Oversize bearing
For radial load capability
and maximum hollow
Standard hollow output shaft mounting output shaft diameter.
Reduces total drive envelope size,
weight and cost. Impregnated and
Single and double solid output shaft machined bearing caps
is available. With exterior machined
surfaces enable a variety
of mounting accessories.
Extra- deep thread
engagement provided for
greater support strength.
Zinc plated hardware.
Vent Free Design.

No breather or vents to leak! Factory
lubricated for life with synthetic, semi-
fluid gear lubricant with an operating
range of -15ºC to 130ºC.
6
Worm Gear Sizes and Torques
Types 030 045 050 063 63A 085 110

20Nm 39Nm 69Nm 140Nm 180Nm 330Nm 620Nm
Types
P45 P50 P63 P6A P85 P10
50Nm 80Nm 170Nm 198Nm 400Nm 730Nm
Types
303 453 503 633 634 6A3 6A4 854 115
30Nm 60Nm 95Nm 200Nm 230Nm 252Nm 264Nm 450Nm 850Nm
Use our web database

or contact us to get
latest updates on
each type/ size
Features
Selection
7
Worm Gear Boxes Codification
HOW TO ORDER
Type Size Mounting
P 045 PA
Worm gearboxes
030
045
050
063
63A
085
110
Worm gearboxes with primary reduction
P45
P50
P63
P6A
P85
P10
Combined worm gearboxes
303
503
633
634
6A3
6A4
854
115
On request can deliver our products according to the ATEX
8
Worm Gear Boxes Codification
HOW TO ORDER
Motor Terminal box Mounting Reduced input Mounting

Ratio Hub Output shaft
size position position bore position
10 C Ø Q B B3 - ---
Only for
See technical combined units
data table See technical
data table
9
Useful formulas
REQUIRED POWER
Lifting P [kW] = M [Kg] •g [9.81] • v [m/ s]

1000
Rotation P [kW] = M [Nm] •n [rpm]

9550
Linear movement P [kW] = F [N] •v [m/ s]

1000
TORQUE
M [Nm] = 9550 •P[KW]

n [rpm]
M [lb in] = 63030 • P[HP]

n [rpm]
RADIAL LOADS
- Radial load generated by external transmissions keyed onto input and/ or output shafts.
FR [N] = M [Nm] •2000 •fk FR [N] = M [lb in] • 8.9 •fk

d [mm] d [in]
M Output torque
d Diam. of driving element
Factor / Coefficiente di trasformazione / Faktor / Coefficiente de transmisión

1.15 Gearwheels
fK 1.25 Chain sprochets
1.75 Narrow v- belt pulley
2.50 Flat- belt pulley
—If your application requires higher radial loads, contact our technical office. Higher load may be possible.
10
How to select a Worm Gear Box
Gear size
045 Rightangle - Gear

39Nm
Rating Alluminium
Output Nominal Nominal Dynamic

B speed
Motor power
power A torque
Flange code
efficiency
Input speed
• QUICK SELECTION
-1
Input speed (n 1) = 1400 min
Output Motor Output Service Nominal Nominal Available Available Dynamic Tooth
Ratio
Speed power torque factor power torque B5 motor flanges B14 motor flanges efficiency Module
n2 P1M M2M P1R M2R B C O P Q Mn[mm] Ratios
-1 i f.s. RD
[min ] [kW] [Nm] [kW] [Nm] 63 71 56 63 71 code
200 7 0.37 14 2.1 0.75 29 B B- C B- C 80 2.2 01
140 10 0.37 20 1.5 0.54 29 B B- C B- C 79 2.2 02
100 14 0.37 27 1.1 0.39 29 B B- C B- C 77 2.4 03
C Ratio Nominal module Notes
Transmitted torque Service factor
fs
D Motor flange available
Type of load and starts per hour Oper. hours per day
<2 h 2- 8h 8 - 16 h
Continuous or B) Mounting with reduction ring
intermittent
Uniform 0.9 1 1.25
appl. with start / hour
≤ 10
C) Motor flangeholes position/ terminal box position
Moderate 1 1.25 1.5
Heavy 1.25 1.5 1.75
B) Available without reduction bushes
Intermittent application
Uniform 1.25 1.5 1.75
with start / hour > 10
Moderate 1.5 1.75 2
Heavy 1.75 2 2.25
A Select required torque (according to service factor)
B Select ouput speed
C On the same line of selected geared motor, you can find the gear ratio
D Select motor flange available (if requested)
11
Single Worm Gear Boxes 030

20Nm
Rating Alluminium
• QUICK SELECTION
-1
input speed (n 1)=1400 min
Ratio
speed power torque factor power torque B5 motor flanges B14 motor flanges effiency Module
n2 P1M M2M P1R M2R A B O P Ratios

-1 i f.s RD Mn [mm]
[min ] [kW] [Nm] [kW] [Nm] 56 63 56 63 code
280 5 0.18 5 3.2 0.57 16 B B- C 82 1.26 01

200 7 0.18 7 2.3 0.42 16 B B- C 80 1.44 02
140 10 0.18 10 1.7 0.30 16 B B- C 78 1.44 03
93 15 0.18 13 1.3 0.24 18 B B- C 73 1.44 04
70 20 0.18 17 1.0 0.19 18 B B- C 70 1.09 05
47 30 0.12 15 1.3 0.16 20 B B- C 62 1.44 06
35 40 0.12 19 1.0 0.12 19 B B- C 57 1.09 07
23 61 0.09 19 1.0 0.09 19 B B- C 50 0.72 08
17.5 80 0.09 16 1.0 0.06 15 B B- C 48 0.56 09
Motor Flanges Available B) Supplied with Reduction Bushing B) Available on Request without reduction bushing C) Motor Flange Holes Position
Unit 030 is supplied with synthetic oil, providing

“long life” lubrication. For mounting position V5- V6 LUBRICATION 030 OIL
please contact us. Quantity 0.03 Lt
See table 1 for lubrication and recommended quantity.
AGIP KLUBER SHELL MOBIL
In table 2 please see possible radial loads and axial
loads on the gearbox. Telium VSF 320 Syntheso D220 EP Tivela Oil WB Glygoyl 30 SHC 630
Tab 1
RADIAL AND AXIAL LOADS
Output Shaft n2 FA FR
[min-1] [N] [N]
200 120 600
150 140 700
100 160 800
75 180 900
50 200 1000
25 250 1250
Input Shaft 15 280 1400
n2 FA FR
[min-1] [N] [N]
1400 20 100
*Strong axial loads in the DX direction are not allowed.
Tab 2
12
Single Worm Gear Boxes 030

3D dimensions on the web
Rightangle - Gear
20Nm 030
P030FB... Basic wormbox Wormbox
weight 1.05 kg
M. flanges Kit code øF A

56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5
56B14 K030.4.046 80 61.5

63B14 K030.4.045 90 62.5
P030PA... Feet P030PB... Feet P030PV... Feet
H R S T U V Y W øZ kit code
type B 55 66 3 87 50 78 94 107 ø6.5 K030.9.022
type S 52 66 3 87 52 90 91 104 ø6.5 KS030.9.023
P030FC... Output flange P030BR... Reaction arm
Type B øD E G L N O P Q Kit code

FC
+0,15
50 +0,05 6 6 50.5 23 68 80 7
1) K030.9.010
2) -
P030..S... Single Shaft P030..D... Double Shaft
+0,15 1) K045.9.010
FL 60 +0,05 6 6 55.5 28 87 110 8.5
2) -
Type S øD E G L N O P Q Kit code
+0,15 1) KS030.9.012
F1 40 +0,10 3.5 5.5 49 21.5 56 80 6.5
2) -
R030FB... Input shaft
kit cod. K030.5.028 type B kit cod. K030.5.029 type B
ød e g l m x kit code b1 c1 d1 e1 f1 l1 m1 n1 t2 o1
type B 9 h6 10.2 3 20 58 - K030.5.006 PAM63 -0,005
type B 5 25 14 35.5 55 126 59 94.5 15.8 M5x14
type S - - - - - - - -0,020
type S - - - - - - - - - -
13
Worm Gear Boxes 045

39Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C O P Q Ratios

-1 i f.s RD Mn [mm]
200 7 0.37 14 2.1 0.76 29 B B- C B- C 80 2.2 01

140 10 0.37 20 1.5 0.54 29 B B- C B- C 79 2.2 02
100 14 0.37 27 1.1 0.39 29 B B- C B- C 77 2.4 03
67 21 0.37 36 1.1 0.41 39 B B- C B- C 67 1.6 04
50 28 0.25 31 1.3 0.31 39 B B- C B- C 65 2.5 05
38 37 0.25 40 1.0 0.25 39 B B- C B- C 63 1.8 06
30 46 0.25 46 0.8 0.21 39 B B- C B- C 59 1.5 07
23 60 0.18 41 0.9 0.17 39 B B- C B- C 56 1.2 08
20 70 0.12 31 0.9 0.11 29 B B- C B- C 54 1.0 09
13.7 102 0.09* 28 <0.8 0.08 28 B B- C B- C 49 0.72 10
* Power higher than the maximum one which can be supported by the gearbox. Select according to the torque M2R.
Unit 045 is supplied with synthetic oil, providing “long LUBRICATION 045 Oil
life” lubrication. For mounting position V5- V6 please
contact us.
Quantity 0.09 Lt.
See table 1 for lubrication and recommended

quantity. AGIP KLUBER SHELL MOBIL
Telium VSF 320 Syntheso D220 EP Tivela Oil WB Glygoyl 30 SHC 630
loads on the gearbox. Tab 1
n2 FA FR
Output Shaft [min-1] [N] [N]
200 180 900
150 200 1000
100 220 1100
75 240 1200
50 260 1400
25 300 1800
15 400 2000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 42 210
Tab 2
14
Worm Gear Boxes 045

Rightangle - Gear
39Nm 045
weight 2.40 kg

63B5 K050.4.041 138 72
71B4 K050.4.042 160 70
56B14 KC40.4.049 80 71.5

63B14 K050.4.047 90 74
71B14 K050.4.045 105 71.5
type B 72 81 3 100 52 98 121 144 ø10.5 K045.9.022
type S 71 84 8 100 70 90 120 143 ø8 KS045.9.023
kit cod. K045.9.027

+0,15 1) K045.9.010
P045..S... P045..D... Double Shaft
FC 60 +0,05 9 9 60.5 28 87 110 8.5
2) - Single Shaft
+0,15 1) K045.9.010
FL 60 +0,05 9 9 90.5 58 87 110 8.5
2) K045.0.200
+0,20 1) KS045.9.013
F1 95 +0,15 4 11 73.5 41 115 140 9
2) -
+0,15 1) KS045.9.010
F2 60 +0,05 9 9 60.5 19 87 110 8.5
3) S045.0.204
+0,15 1) KS045.9.014
F3 80 +0,10 3 8 51.5 19 100 120 9
2) -

kit cod. KS045.5.030 type S kit cod. KS045.5.031 type S
1) K045.5.006 PAM71 -0,005
type B 11 h6 12.5 4 30 68 - type B 6 32 18 43 65 151 70 113 20.5 M6x18
2) - -0,020
1) - -0,005
type S - - - - - - type S 6 40 19 58.8 65 182 70 128.5 21.5 M8x20
2) - -0,020
15
Worm Gear Boxes 050

69Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C D O P Q R Ratios

-1 i f.s RD Mn [mm]
[min ] [kW] [Nm] [kW] [Nm] 63 71 80 56 63 71 80 code
200 7 0.75 29 1.8 1.4 54 B B B- C B 82 2.5 01

140 10 0.75 41 1.4 1.1 59 B B B- C B 80 2.4 02
100 14 0.75 57 1.1 0.86 65 B B B- C B 79 2.6 03
78 18 0.55 51 1.2 0.64 59 B B B- C B 75 2.0 04
54 26 0.55 67 0.9 0.51 63 B B B- C B 69 2.7 05
39 36 0.37 63 1.1 0.41 69 B B- C B- C 69 2.1 06
33 43 0.37 72 0.9 0.34 65 B B- C B- C 66 1.8 07
23 60 0.25 59 1.0 0.25 59 B B- C B- C 58 1.3 08
21 68 0.25 66 0.8 0.21 55 B B- C B- C 57 1.2 09
17.5 80 0.18 53 1.0 0.18 54 B B- C B- C 54 1.0 10
14 100 0.12 41 1.2 0.14 49 B B- C B- C 50 0.8 11
Unit 050 is supplied with synthetic oil, providing “long

contact us.
LUBRICATION 050 OIL
Quantity 0.14 Lt

loads on the gearbox. AGIP KLUBER SHELL MOBIL
Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
200 240 1200
150 280 1400
100 300 1500
75 340 1700
50 380 1900
25 480 2500
15 560 2800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 76 380
Tab 2
16
Worm Gear Boxes 050

Rightangle - Gear
69Nm 050
weight 3.00 kg
M. flanges Kit.code øF A
63B5 K050.4.041 138 76.5
71B5 K050.4.042 160 74.5
80B5 K050.4.043 200 76.5

56B14 KC40.4.049 80 76
63B14 K050.4.047 90 78.5
71B14 K050.4.045 105 76
80B14 K050.4.046 120 76.5
type B 82 98.5 3.5 123 63 113 138.5 163 ø10.5 K050.9.022
type S 85 96 10 114 85 110 139.5 166 ø10 KS050.9.023
kit cod. K050.9.027

+0,20 1) K050.9.010
FC 70 +0,15 9 12 85 44.5 90 123 10.5
2) - Single Shaft
+0,20 1) K050.9.010
FL 70 +0,15 9 12 114.5 74 90 123 10.5
2) K050.0.200
+0,20 1) KS050.9.012
F1 110 +0,15 4 11 83.5 43 130 160 10
2) -
+0,20 1) KS050.9.014
F2 70 +0,15 9 12 76.5 36 90 123 10.5
2) -
+0,20 1) KS050.9.013
F3 95 +0,15 4 10 66.5 26 115 140 10
2) -

b1 c1 d1 e1 f1 l1 m1 n1 t2 o1
ød e g l m x kit code
-0,005
1) K050.5.006 PAM71 type B 8 52 25 59.5 81 200 86.5 146 28 M8x20
type B 16 h6 18 5 30 74.5 M6x16 -0,020
2) K050.5.007 PAM80
-0,005
1) KS050.5.008 PAM71 type S 8 50 24 68.8 81 218 86.5 155 27 M8x20
type S 14 h6 16 5 30 74.5 M5x10 -0,020
2) KS050.5.009 PAM80
17
Worm Gear Boxes 063

140Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C D E Q R T Ratios

-1 i f.s RD Mn [mm]
200 7 1.8 71 1.7 3.0 119 B B B- C B- C 83 3.1 01

140 10 1.8 99 1.3 2.3 128 B B B- C B- C 81 3.1 02
93 15 1.5 121 1.1 1.6 131 B B B- C B- C 79 3.1 03
74 19 1.1 111 1.2 1.3 131 B B B- C B- C 78 2.6 04
58 24 1.1 135 1.0 1.1 135 B B B- C B- C 75 2.0 05
47 30 1.1 167 0.8 0.92 139 B B B- C B- C 74 3.2 06
39 36 0.75 125 1.1 0.84 140 B B B- C B- C 68 2.7 07
31 45 0.55 111 1.2 0.64 129 B B B- C C 66 2.1 08
21 67 0.55 151 0.8 0.43 118 B B B- C C 60 1.5 09
17.5 80 0.37 115 1.0 0.36 113 B B B- C C 57 1.3 10
14.9 94 0.37 123 0.9 0.34 113 B B B- C C 52 1.1 11

contact us. LUBRICATION 063 OIL
Quantity 0.40 Lt
In table 2 please see possible radial loads and axial AGIP KLUBER SHELL MOBIL
loads on the gearbox.

Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
200 360 1800
150 400 2000
100 460 2300
75 500 2500
50 600 3000
25 700 3800
15 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 90 450
Tab 2
18
Worm Gear Boxes 063

Rightangle - Gear
140Nm 063
weight 6.00 kg

63B5 K063.4.041 140 99.5
71B5 K063.4.042 160 97.5
80/90B5 K063.4.043 200 99.5
71B14 K063.4.047 105 97.5

80B14 K063.4.046 120 98.5
90B14 K063.4.041 140 99.5
type B 100 111 4 144 95 133 170 200 ø10.5 1) K063.9.022
type S - - - - - - - - - -
kit cod. K063.9.027

+0,20 1) K063.9.010
FC 115 +0,15 7 13 86 26 150 175 11
2) - Single Shaft
+0,20 1) K063.9.010
FL 115 +0,15 7 13 116 56 150 175 11
2) K063.0.200
+0,20 1) KS070.9.013
F1 130 +0,15 7 13 102 42 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS063.9.011
F3 110 5 11 82 22 130 160 10
0 2) -
1) K063.5.006 PAM80 -0,005
type B 18 h6 20.5 6 45 93 M6x16 type B 8 60 25 63.2 120 246.4 126.8 190 28 M8x20
2) K063.5.007 PAM90 -0,020
1) K063.5.008 PAM80 type S - - - - - - - - - -
type S 19 h6 21.5 6 40 93 M8x20
2) K063.5.009 PAM90
19
Worm Gear Boxes 63A
63A Rightangle - Gear

180Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C D E Q R T Ratios

-1 i f.s RD Mn [mm]
200 7 1.8 71 2.2 3.9 155 B B B- C B- C 83 3.1 01

140 10 1.8 99 1.7 3.0 165 B B B- C B- C 81 3.1 02
93 15 1.5 121 1.4 2.1 169 B B B- C B- C 79 3.1 03
74 19 1.5 152 1.1 1.7 169 B B B- C B- C 78 2.6 04
58 24 1.5 184 1.0 1.4 176 B B B- C B- C 75 2 05
47 30 1.5 227 0.8 1.2 180 B B B- C B- C 74 3.2 06
39 36 1.1 184 1.0 1.1 181 B B B- C B- C 68 2.7 07
31 45 0.75 152 1.1 0.82 167 B B B- C C 66 2.1 08
21 67 0.55 151 1.0 0.55 151 B B B- C C 60 1.5 09
17.5 80 0.37 115 1.3 0.47 146 B B B- C C 57 1.3 10
14.9 94 0.37 123 1.0 0.37 124 B B B- C C 52 1.1 11
Unit 63A is supplied with synthetic oil, providing “long

contact us.
LUBRICATION 63A OIL
See table 1 for lubrication and recommended quantity. Quantity 0.40 Lt
Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
200 360 1800
150 400 2000
100 460 2300
75 500 2500
50 600 3000
25 700 38000
15 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 90 450
Tab 2
20
Worm Gear Boxes 63A

Rightangle - Gear
180Nm 63A
P63AFB... Basic wormbox Wormbox
weight 6.00 kg
63B5 K063.4.041 140 99.5
71B5 K063.4.042 160 97.5
80/90B5 K063.4.043 200 99.5

71B14 K063.4.047 105 97.5
80B14 K063.4.046 120 98.5
90B14 K063.4.041 140 99.5
P63APA... Feet P63APB... Feet P63APV... Feet
type B 115 115 12 142 120 156 185 215 ø11 K070.9.022
type S - - - - - - - - - -
P63AFC... Output flange P63ABR... Reaction arm
kit cod. K063.9.027

P63A..S... P63A..D... Double Shaft
+0,20 1) K070.9.010
FC 130 +0,15 7 13 85 25 165 200 13
2) - Single Shaft
+0,20 1) K070.9.010
FL 130 +0,15 7 13 111 51 165 200 13
2) K070.0.200
+0,20 1) KS070.9.014
F1 130 +0,15 7 13 111 51 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS070.9.011
F3 110 5 13.5 84.5 24.5 130 160 11
0 2) -
R63AFB... Input shaft
1) K063.5.006 PAM80 -0,005
type B 18 h6 20.5 6 45 93 M6x16 type B 8 60 28 63.5 120 247 127.5 191 31 M8x20
2) K063.5.007 PAM90 -0,020
1) KS063.5.008 PAM80 type S - - - - - - - - - -
type S 19 h6 21.5 6 40 93 M8X20
2) KS063.5.009 PAM90
21
Worm Gear Boxes 085

330Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R F U

C D E R T Ratios
-1 i f.s 100 100 RD Mn [mm]
112 112
200 7 4.0 168 1.5 5.8 245 B B B B 88 4.23 01

140 10 4.0 218 1.2 4.9 270 B B B B 80 4.2 02
100 14 3.0 223 1.3 3.9 290 B B B B 78 4.5 03
70 20 2.2 237 1.2 2.6 280 B B B B 79 3.4 04
64 22 2.2 258 1.1 2.4 280 B B B B 78 3.1 05
50 28 2.2 315 1.0 2.3 330 B B B B 75 4.7 06
37 38 1.5 276 1.2 1.7 320 B B B 71 3.5 07
30 46 1.5 320 1.0 1.4 310 B B B 68 3.1 08
27 52 1.1 258 1.1 1.2 275 B B B 66 2.7 09
21 67 1.1 327 0.8 0.93 275 B B B 65 2.1 10
18.9 74 0.75 220 1.2 0.87 255 B B B 58 1.9 11
14.6 96 0.55 191 1.2 0.66 230 B B B 53 1.5 12

contact us.
LUBRICATION 085 Oil Quantity 1.20 Lt
Tab 1
[min-1] [N] [N]
200 500 2500
150 580 2900
100 600 3000
75 700 3500
50 800 4000
25 1000 5000
15 1160 5800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 160 809
Tab 2
22
Worm Gear Boxes 085

Rightangle - Gear
330Nm 085
weight 11.00 kg
71B5 K023.4.041 160 116
80/90B5 K023.4.042 200 118
100/112B5 K023.4.043 250 124

80B14 K085.4.046 120 116
90B14 K085.4.045 140 116
100/112B14 k023.4.041 160 116
type B 142 145 5 182 140 180 236,5 280 ø10,5 K085.9.022
type S - - - - - - - - - -

+0,06 1) K085.9.010
FC 152 +0,00 5 16 108 40.5 176 205 13
2) - Single Shaft
+0,06 1) K085.9.010
FL 152 +0,00 5 16 148.5 81 176 205 13
2) K085.0.201
1) KS085.9.012
F1 130 H7 5 13 117.5 50 165 200 11.5
2) -
+0,06 1) KS085.9.013
F2 152 +0,00 5 15 147.5 80 180 205 12.5
2) -
1) KS085.9.015
F3 130 H7 5 13 106.5 39 165 200 13
2) -
K085.5.007PAM90 -0,005
type B 25h6 28 8 50 112 M8X20 type B 10 60 35 73.5 135 282 141 214.5 38 M10x23
K085.5.008PAM100 -0,020
KS085.5.009PAM90 type S - - - - - - - - - -
type S 24h6 27 8 50 112 M8X20
KS085.5.011PAM100
23
Worm Gear Boxes 110

620Nm
Rating - Cast Iron
• QUICK SELECTION
-1
Ratio

C D E R T Ratios
-1 i f.s 100 100 RD Mn [mm]
112 112
200 7 4.0 168 2,7 10,9 460 B B B B 88 5,5 01

140 10 4.0 235 2,1 8,5 500 B B B B 86 5,4 02
88 16 4.0 358 1,4 5,7 510 B B B B 82 5,3 03
70 20 4.0 447 1,2 4,6 520 B B B B 82 4,5 04
61 23 3.0 377 1,3 3,9 490 B B B B 80 3,9 05
47 30 3.0 467 1,3 4 620 B B B B 76 5,6 06
37 38 3.0 583 1,0 3,1 610 B B B B 75 4,7 07
31 45 2,2 493 1,2 2,5 570 B B B B 73 4 08
26 53 2,2 557 1,1 2,3 590 B B B B 70 3,5 09
22 64 1,5 452 1,1 1,7 510 B B B 69 2,9 10
16,7 84 1,1 410 1,1 1,3 470 B B B 65 2,2 11
14,1 99 1,1 446 1,0 1,1 460 B B B 60 1,9 12
Unit 110 is supplied without lubricant and equipped

with a breather, level and drain plugs. User can add
mineral oil keeping existing plugs. Should the user
wish to fill it with synthetic oil, it is recommended to
replace the existing plugs with a closed plug.
See table 1 for lubrication and recommended

quantity. 2.00 LT 1.50 LT 1.50 LT 2.00 LT 2.00 LT 2.00 LT

Tab 1

n2 FA FR
200 600 2900
150 700 3300
100 750 3600
75 800 4000
50 920 4600
25 1200 6000
15 1400 7000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 228 1140
Tab 2
24
Worm Gear Boxes 110

Rightangle - Gear
620Nm 110
weight 35.00 kg
71B5 K023.4.041 160 135,5
80/90B5 K023.4.042 200 137,5
100/112B5 K023.4.043 250 143,5

80B14 K085.4.046 120 135,5
90B14 K085.4.045 140 135,5
100/112B14 k023.4.041 160 135,5
Type B 170 180 22 224 200 240 286 333 Ø13 K110.9.022
Type S 172 160 18 190 200 240 288 335 Ø14 KS110.9.023

+0,083 1) K110.9.010
FC 170 +0,043 11 16.5 131.5 54 230 270 13
2) - Single Shaft
+0,083 1) K110.9.011
FL 170 +0,043 11 16.5 179.5 102 230 270 13
2) -
+0,040 1) KS110.9.014
F1 180 5 18 150 172.5 215 250 15
0 2) -
+0,083 1) KS110.9.012
F2 170 +0,043 9.5 15 178 100.5 230 270 13
2) -
+0,040 1) KS110.9.013
F3 180 5 18 130 52.5 215 250 15
0 2) -
1) K085.5.007PAM90 -0,005
type B 25h6 28 8 50 131,5 M8X20 type B 12 75 42 96.5 155 348 163.5 260 45 M12x32
2) K085.5.008PAM100 -0,020
1) KS085.5.009PAM90 type S - - - - - - - - - -
type S 24h6 27 8 50 131,5 M8X20
2) KS085.5.011PAM100
25
Single Worm Gear Boxes with Spur Gear P45
P45 Rightangle - Gear

50Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C P Q Ratios

-1 i f.s RD Mn [mm]
47 30.1 0.25 38 1.3 0.33 50 C 74 2.2 01

33 43.0 0.25 53 0.9 0.24 50 C 72 2.4 02
23 60.2 0.12 30 1.7 0.20 50 C 60 1.6 03
15.5 90.3 0.12 42 1.2 0.14 50 C 57 2.5 04
11.6 120 0.12 52 1.0 0.11 50 C 53 1.8 05
8.8 159 0.12 64 0.8 0.09 50 C 49 1.5 06
7.1 198 0.12* 50 <0.8 0.08 50 C 47 1.5 07
5.4 258 0.12* 50 <0.8 0.06 50 C 45 1.0 08
4.7 301 0.12* 35 <0.8 0.04 35 C 40 0.72 09
3.2 439 0.12* 35 <0.8 0.03 35 C 36 0.72 10
* Power higher than the maximum one which can be supported by the gearbox. Select according to the torque M2R
Unit P45 is supplied with synthetic oil, providing “long

contact us.
LUBRICATION P45 OIL
See table 1 for lubrication and recommended quantity. Quantity 0.09/0.04 Lt


Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
75 240 1200
50 260 1400
25 300 1800
15-6 400 2000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 44 220
Tab 2
26

Rightangle - Gear
50Nm P45
PP45FB... Basic wormbox Wormbox
3.20 kg
weight
63B5 K050.4.041 138 137.5
71B5 K050.4.042 160 135.5

63B14 K050.4.047 90 139.5
71B14 K050.4.045 105 137
PP45PA... Feet PP45PB... Feet PP45PV... Feet
H R t u S V Y W øZ Kit code
Type B 72 81 100 52 3 98 121 144 ø10.5 K045.9.022
Type S 71 84 100 70 8 90 120 143 ø8 KS045.9.023
PP45FC... Output flange PP45BR... Reaction arm
kit cod. K045.9.027

FC
+0,15
60 +0,05 9 9 60.5 28 87 110 8.5
1) K045.9.010
2) -
PP45..S... Single Shaft PP45..D... Double Shaft
+0,15 1) K045.9.010
FL 60 +0,05 9 9 90.5 58 87 110 8.5
2) K045.0.200
+0,20 1) KS045.9.013
F1 95 +0,15 4 11 73.5 41 115 140 9
2) -
+0,15 1) KS045.9.010
F2 60 +0,05 9 9 60.5 19 87 110 8.5
3) S045.0.204
+0,03 1) KS045.9.014
F3 80 +0,00 3 8 51.5 19 100 120 9
2) -
RP45FB... Input shaft

b1 c1 d1 e1 f1 l1 m1 n1 t2 o1
ød e g l m x -0,005
type B 6 32 18 43 65 151 70 113 20.5 M6x18
type B 14 j6 16 5 25 131 M5x13 C35.5.061 -0,020
type S - - - - - - -0,005
type S 6 40 19 58.8 65 182 70 128.5 21.5 M8x20
-0,020
27

80Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C P Q Ratios
-1 i f.s RD Mn [mm]
47 30.1 0.37 58 1.2 0.45 70 C 76 2.4 01

33 43.0 0.25 55 1.3 0.32 70 C 75 2.6 02
23 60.2 0.25 71 1.0 0.25 70 C 69 2.0 03
18.1 77.4 0.18 58 1.4 0.25 80 C 61 2.7 04
12.5 112 0.18 84 1.0 0.17 80 C 61 2.1 05
9.0 155 0.12 71 1.1 0.14 80 C 56 1.8 06
7.6 185 0.12 74 0.9 0.11 70 C 49 1.3 07
5.4 258 0.12* 70 <0.8 0.08 70 C 47 1.2 08
4.8 292 0.12* 60 <0.8 0.07 60 C 44 1.0 09
4.1 344 0.12* 40 <0.8 0.04 40 C 40 0.8 10
3.3 430 0.12* 40 <0.8 0.04 40 C 36 0.8 11
* Power higher than the maximum one which can be supported by the gearbox. Select according to the torque M2R.

life” lubrication. For mounting position V5- V6 please LUBRICATION P50 Oil
contact us. Quantity 0.14/0.04 Lt.

Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
75 340 1700
50 380 1900
25 480 2500
15-6 560 2800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 44 220
Tab 2
28

Rightangle - Gear
80Nm P50
weight 3.80 kg
63B5 K050.4.041 138 142
71B5 K050.4.042 160 140

63B14 K050.4.047 90 144
71B14 K050.4.045 105 141.5
type B 82 98.5 3.5 123 63 113 138.5 163 ø10.5 K050.9.022
type S 85 96 10 114 85 110 139.5 166 ø10 KS050.9.023
kit cod. K050.9.027

+0,20 1) K050.9.010
PP50..S... PP50..D... Double Shaft
FC 70 +0,15 9 12 85 44.5 90 123 10.5
2) - Single Shaft
+0,20 1) K050.9.010
FL 70 +0,15 9 12 114.5 74 90 123 10.5
2) K050.0.200
+0,20 1) KS050.9.012
F1 110 +0,15 4 11 83.5 43 130 160 10
2) -
+0,20 1) KS050.9.014
F2 70 9 12 76.5 36 90 123 10.5
+0,15 2) -
+0,035 1) KS050.9.013
F3 95 4 10 66.5 26 115 140 10
0 2) -

ød e g l m x b1 c1 d1 e1 f1 l1 m1 n1 t2 o1
type B 14 j6 16 5 25 135.5 M5x13 C35.5.061 -0,005
type B 8 52 25 59.5 81 200 86.5 146 28 M8x20
type S - - - - - - -0,020
-0,005
type S 8 50 24 68.8 81 218 86.5 155 27 M8x20
-0,020
29

170Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C D E P Q R T Mn Ratios
-1 i f.s. RD
[min ] [kW] [Nm] [kW] [Nm] 63 71 80 90 63 71 80 90 [mm] code
IEC 47 29.9 0.75 113 1.3 0.99 150 C C 74 2.6 01
90-80-71 37 37.7 0.75 141 1.1 0.80 150 C C 73 2.0 02
30 47.1 0.75 169 1.0 0.76 170 C C 70 3.2 03
25 56.6 0.55 136 1.3 0.69 170 C C 64 2.7 04
19.8 70.7 0.37 111 1.5 0.57 170 C C 62 2.1 05
15.9 87.8 0.37 162 1.1 0.39 170 C C 73 2.6 06
12.6 111.0 0.37 199 0.9 0.32 170 C C 71 2.0 07
IEC 10.1 139 0.37 234 0.7 0.27 170 C 67 3.2 08
71-63 8.4 166 0.25 173 1.0 0.25 170 C 61 2.7 09
6.7 208 0.18 151 1.0 0.18 150 C 59 2.1 10
4.5 310 0.12 129 1.2 0.14 150 C 51 1.5 11
3.8 370 0.12 145 1.0 0.12 150 C 48 1.3 12
3.2 434 0.12 149 0.8 0.10 125 C 42 1.1 13

contact us.
LUBRICATION P63 Oil
See table 1 for lubrication and recommended quantity. Quantity 0.40/0.08 Lt.

Tab 1
Output Shaft
n2 FA FR
[min-1] [N] [N]
75 500 2500
50 600 3000
25 700 3800
15-6 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 61 305
Tab 2
30

Rightangle - Gear
170Nm P63
PP63FB...
29.9÷111 139÷434
Basic wormbox
Wormbox 7.30 7.80
weight Kg Kg
M.flanges Kit code øF A
71B5 K063.4.042 160 176,5
80/90B5 K063.4.043 200 178,5
29.9÷111 71B14 K063.4.047 105 176,5
80B14 K063.4.046 120 177,5
90B14 K063.4.041 140 178,5
63B5 K050.4.041 138 160,5

139÷434 71B5 K050.4.042 160 158,5
63B14 K050.4.047 90 160,5
71B14 K050.4.045 105 160
Type B 100 111 4 144 95 133 170 200 ø10.5 K063.9.022
Type S - - - - - - - - - -
kit cod. K063.9.027

+0,20 1) K063.9.010
FC 115 +0,15 7 13 86 26 150 175 11
2) - Single Shaft
+0,20 1) K063.9.010
FL 115 +0,15 7 13 116 56 150 175 11
2) K063.0.200
+0,20 1) KS070.9.013
F1 130 +0,15 7 13 102 42 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS063.9.011
F3 110 5 11 85 22 130 160 10
0 2) -
29.9÷111 19 j5 21.5 6 35 169.4 M6x16 C40.5.062 -0,005
type B 8 60 25 63.2 120 246.4 126.8 190 28 M8x20
139÷434 14 j5 16 5 25 154.2 M5x13 C35.5.061 -0,020
type S - - - - - - - - - -
31
Single Worm Gear Boxes with Spur Gear P6A
P6A Rightangle - Gear

198Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
n2 P1M M2M P1R M2R B C D E P Q R T Mn Ratios
-1 i f.s. RD
[min ] [kW] [Nm] [kW] [Nm] 63 71 80 90 63 71 80 90 [mm] code
IEC 47 29.9 0.75 113 1.5 1.09 165 C C 74 2.6 01
90-80-71 37 37.7 0.75 141 1.2 0.88 165 C C 73 2.0 02
30 47.1 0.75 169 1.1 0.83 187 C C 70 3.2 03
25 56.6 0.55 136 1.4 0.76 187 C C 64 2.7 04
19.8 70.7 0.37 109 1.7 0.64 187 C C 61 2.1 05
15.9 87.8 0.37 160 1.2 0.46 198 C C 72 2.6 06
12.6 111.0 0.37 196 1.0 0.37 198 C C 70 2.0 07
IEC 10.1 139 0.37 231 0.9 0.32 198 C 66 3.2 08
71-63 8.4 166 0.25 170 1.2 0.29 198 C 60 2.7 09
6.7 208 0.25 195 0.9 0.23 176 C 55 2.1 10
4.5 310 0.18 194 0.9 0.16 176 C 51 1.5 11
3.8 370 0.18 213 0.8 0.15 176 C 47 1.3 12
3.2 434 0.18* 130 <0.8 0.10 130 C 42 1.1 13
Unit P6A is supplied with synthetic oil, providing “long

contact us. LUBRICATION P63 Oil
Quantity 0.40/0.08 Lt
Tab 1
[min-1] [N] [N]
75 500 2500
50 600 3000
25 700 3800
15-6 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 61 305
Tab 2
32
Single Worm Gear Boxes with Spur Gear P6A

Rightangle - Gear
198Nm P6A
PP6AFB...
29.9÷111 139÷434
Basic wormbox
Wormbox 7.30 7.80
weight Kg Kg
M.flanges Kit code øF A
71B5 K063.4.042 160 176,5
80/90B5 K063.4.043 200 178,5
29.9÷111 71B14 K063.4.047 105 176,5
80B14 K063.4.046 120 177,5
90B14 K063.4.041 140 178,5
63B5 K050.4.041 138 160,5

139÷434 71B5 K050.4.042 160 158,5
63B14 K050.4.047 90 160,5
71B14 K050.4.045 105 160
PP6APA... Feet PP6APB... Feet PP6APV... Feet
Type B 115 115 12 142 120 156 185 215 ø11 K070.9.022
Type S - - - - - - - - - -
PP6AFC... Output flange PP6ABR... Reaction arm
kit cod. K063.9.027

+0,20 1) K070.9.010
PP6A..S... PP6A..D... Double Shaft
FC 130 +0,15 7 13 85 25 165 200 13
2) - Single Shaft
+0,20 1) K070.9.010
FL 130 +0,15 7 13 111 51 165 200 13
2) K070.0.200
+0,20 1) KS070.9.014
F1 130 +0,15 7 13 111 51 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS070.9.011
F3 110 5 13.5 84.5 24.5 130 160 11
0 2) -
RP6AFB... Input shaft
29.9÷111 19 j5 21.5 6 35 169.4 M6x16 C40.5.062 -0,005
type B 8 60 28 63.5 120 247 127.5 191 31 M8x20
139÷434 14 j5 16 5 25 154.2 M5x13 C35.5.061 -0,020
type S - - - - - - - - - -
33

400Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
C D E R T Mn[mm] Ratios
-1 i f.s 100 100 RD
112 112
23.5 59.7 1.1 300 1.3 1.39 380 C C 67 3.5 01
19.4 72.3 1.1 347 1.1 1.17 370 C C 64 3.1 02
17.1 81.7 1.1 374 1.0 1.12 380 C C 61 2.7 03
13.3 105 0.75 323 1.1 0.81 350 C C 60 2.1 04
8.0 176 0.55 415 1.0 0.53 400 B C C 63 3.5 05
6.6 213 0.37 322 1.1 0.43 370 B C C 60 3.1 06
5.8 240 0.37 321 1.2 0.44 380 B C C 53 2.7 07
4.3 328 0.37 438 0.9 0.32 380 B C C 53 2.7 08
3.3 422 0.25 374 0.9 0.23 350 B C C 52 2.1 09
3.0 466 0.25 358 0.8 0.21 300 B C C 45 1.9 10
2.3 605 0.18 297 1.0 0.18 300 B C C 40 1.5 11

life” lubrication. For mounting position V5- V6 please •LUBRICATION P85 Oil
contact us. Quantity 1.20/0.14 Lt.
Tab 1
[min-1] [N] [N]
75 700 3500
50 800 4000
25 1000 5000
15-6 1160 5800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 108 540
Tab 2
34

Rightangle - Gear
400Nm P85
weight 19.30 kg
63B5 K063.4.041 140 195.2
71B5 K063.4.042 160 193.2
80/90B5 K063.4.043 200 195.2

71B14 K063.4.047 105 193.2
80B14 K063.4.046 120 194.2
90B14 K063.4.041 140 195.2
Type B 142 145 5 182 140 180 236.5 280 ø10.5 K085.9.022
Type S - - - - - - - - - -
kit cod. K085.9.027

1) K085.9.010
+0,06
FC 152 +0,00 5 16 108 40.5 176 205 13 Single Shaft
2) -
+0,06 1) K085.9.010
FL 152 +0,00 5 16 148.5 81 176 205 13
2) K085.0.201
+0,04 1) KS085.9.012
F1 130 +0,00 5 13 117.5 50 165 200 11.5
2) -
+0,06 1) KS085.9.013
F2 152 +0,00 5 15 147.5 80 180 205 12.5
2) -
+0,04 1) KS085.9.015
F3 130 +0,00 5 13 106.5 39 165 200 13
2) -
type B 19 j5 21.5 6 35 187.5 M6x16 C40.5.062 -0,005
type B 10 60 35 73.5 135 282 141 214.5 38 M10x23
type S - - - - - - -0,020
type S - - - - - - - - - -
35

730Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s 100 100 RD
112 112
16,8 83,2 1,5 562 1,1 1,6 600 C 69 3,5 01
13,9 100,5 1,5 651 0,8 1,2 540 C 68 2,9 02
10,6 132 1,1 574 0,9 1,0 500 C 64 2,2 03
8 176 0,75 594 1,2 0,92 730 B C 74 4,7 04
6,7 208 0,75 670 0,9 0,67 600 B C 72 4,0 05
5,7 245 0,55 570 1,1 0,58 600 B C 69 3,5 06
4,7 296 0,55 611 0,9 0,49 540 B C 68 2,9 07
4,2 334 0,55 689 0,9 0,48 600 B C 69 3,5 08
3,5 403 0,37 519 1,0 0,39 540 B C 68 2,9 09
2,6 529 0,25 424 1,2 0,29 500 B C 64 2,2 10
2,2 624 0,25 479 1,0 0,25 480 B C 59 1,9 11
Unit P10 is supplied without lubricant and equipped with

a breather, level and drain plugs. User can add mineral
oil keeping existing plugs. Should the user wish to fill it
with synthetic oil, it is recommended to replace the
existing plugs with a closed plug. Primary reduction unit
is supplied with closed plugs and lubricated for life with
synthetic oil.

In table 2 please see possible radial loads and axial Tab 1
[min-1] [N] [N]
75 800 4000
50 920 4600
25 1200 6000
15-6 1400 7000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 150 760
Tab 2
36

Rightangle - Gear
730Nm P10
weight 41.00 kg
63B5 K063.4.041 140 214.7
71B5 K063.4.042 160 212.7
80/90B5 K063.4.043 200 214.7

71B14 K063.4.047 105 212.7
80B14 K063.4.046 120 213.7
90B14 K063.4.041 140 214.7
Type B 170 180 22 224 200 240 286 333 ø13 K110.9.022
Type S 172 160 18 190 200 240 288 335 ø14 K110.9.023
kit cod. K110.9.027

+0,083 1) K110.9.010
FC 170 +0,043 11 16.5 131.5 54 230 270 13 Single Shaft
2) -
+0,083 1) K110.9.011
FL 170 +0,043 11 16.5 179.5 102 230 270 13
2) -
+0,040 1) KS110.9.014
F1 180 5 18 150 72.5 215 250 15
0 2) -
+0,083 1) KS110.9.012
F2 170 +0,043 9.5 15 178 100.5 230 270 13
2) -
+0,040 1) KS110.9.013
F3 180 5 18 130 52.5 215 250 15
0 2) -
type B 19 j5 21.5 6 35 205 M6x16 C40.5.062 -0,005
type B 12 75 42 96.5 155 348 163.5 260 45 M12x32
type S - - - - - - -0,020
type S - - - - - - - - - -
37
Combined Worm Gear Unit
303 Rightangle - Gear 030+030

30Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s RD Mn [mm]
9.3 150 0.06 29 1.0 0.06 30 B B- C 48 1.44 01

6.7 210 0.06 39 0.8 0.05 30 B B- C 45 1.44 02
4.7 300 0.06* 30 <0.8 0.04 30 B B- C 36 1.44 03
3.1 450 0.06* 30 <0.8 0.03 30 B B- C 33 1.44 04
2.3 600 0.06* 30 <0.8 0.02 30 B B- C 30 1.44 05
1.6 900 0.06* 30 <0.8 0.02 30 B B- C 27 1.44 06
1.2 1200 0.06* 30 <0.8 0.01 30 B B- C 26 1.44 07
0.8 1830 0.06* 30 <0.8 0.01 30 B B- C 24 1.44 08
0.6 2400 0.06* 30 <0.8 0.01 30 B B- C 22 1.44 09
* Power higher than the maximum one which can be supported by the gearbox. Select according to the torque
M2R



Tab 1
[min-1] [N] [N]
25 300 1800
15 400 2000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 20 100
Tab 2
38

Rightangle - Gear
30Nm 303
weight 2.15 kg
56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5

56B14 K030.4.046 80 61.5
63B14 K030.4.045 90 62.5
type B 55 66 3 87 50 78 94 107 ø6.5 K030.9.022
type S 52 66 3 87 52 90 91 104 ø6.5 KS030.9.023

kit cod. K045.9.027

1) K030.9.010
+0,15
FC 50 +0,05 6 6 50.5 23 68 80 7 Single Shaft
2) -
+0,15 1) K030.9.011
FL 60 +0,05 6 6 55.5 28 87 110 8.5
2) -

+0,15 1) KS030.9.012
F1 40 +0,10 3.5 5.5 49 21.5 56 80 6.5
2) -
type B 9 h6 10.2 3 20 58 - K030.5.006 PAM63 -0,005
type B 5 25 14 35.5 55 126 59 94.5 15.8 M5x14
type S - - - - - - - -0,020
type S - - - - - - - - - -
39

60Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s RD Mn [mm]
10.0 140 0.12 57 1.0 0.13 60 B B- C 50 2.2 01
7.0 200 0.12 79 0.8 0.09 60 B B- C 48 2.2 02
5.0 280 0.12* 60 <0.8 0.07 60 B B- C 45 2.4 03
3.3 420 0.12* 60 <0.8 0.06 60 B B- C 36 1.6 04
2.5 560 0.12* 60 <0.8 0.05 60 B B- C 33 2.5 05
1.9 740 0.12* 60 <0.8 0.04 60 B B- C 30 1.8 06
1.5 920 0.12* 60 <0.8 0.04 60 B B- C 27 1.5 07
1.3 1120 0.12* 60 <0.8 0.03 60 B B- C 26 2.5 08
0.9 1480 0.12* 60 <0.8 0.02 60 B B- C 24 1.8 09
0.8 1840 0.12* 60 <0.8 0.02 60 B B- C 22 1.5 10
0.6 2400 0.12* 60 <0.8 0.02 60 B B- C 21 1.2 11

contact us.
LUBRICATION 453 OIL
Tab 1
[min-1] [N] [N]
25 300 1800
15 400 2000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 20 100
Tab 2
40

Rightangle - Gear
60Nm 453
weight 3.60 kg
56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5

56B14 K030.4.046 80 61.5
63B14 K030.4.045 90 62.5
type B 72 81 3 100 52 98 121 144 ø10.5 K045.9.022
type S 71 84 8 100 70 90 120 143 ø8 KS045.9.023

kit cod. K045.9.027

+0,15 1) K045.9.010
FC 60 +0,05 9 9 60.5 28 87 110 8.5
2) - Single Shaft
+0,15 1) K045.9.010
FL 60 +0,05 9 9 90.5 58 87 110 8.5
2) K045.0.200
+0,20 1) KS045.9.013
F1 95 +0,15 4 11 73.5 41 115 140 9
2) -
+0,15 1) KS045.9.010
F2 60 +0,05 9 9 60.5 19 87 110 8.5
3) S045.0.204
+0,030 1) KS045.9.014
F3 80 3 8 51.5 19 100 120 9
0 2) -

1) K030.5.006 PAM63 -0,005
type B 9 h6 10.2 3 20 58 - type B 6 32 18 43 65 151 70 113 20.5 M6x18
2) - -0,020
1) - -0,005
type S - - - - - - type S 6 40 19 58.5 65 182 70 128.5 21.5 M8x20
2) - -0,020
41

95Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s RD Mn [mm]
5.6 252 0.12 97 1.0 0.12 95 B B- C 47 2.1 01

3.9 360 0.12 124 0.8 0.09 95 B B- C 42 2.1 02
2.6 540 0.12* 95 <0.8 0.07 95 B B- C 39 2.1 03
1.9 720 0.12* 95 <0.8 0.05 95 B B- C 36 2.1 04
1.6 860 0.12* 95 <0.8 0.05 95 B B- C 32 1.8 05
1.2 1200 0.12* 95 <0.8 0.04 95 B B- C 27 1.3 06
1.0 1440 0.12* 95 <0.8 0.04 95 B B- C 26 2.1 07
0.8 1720 0.12* 95 <0.8 0.03 95 B B- C 25 1.8 08
0.6 2400 0.12* 90 <0.8 0.03 90 B B- C 21 1.3 09



Tab 1
[min-1] [N] [N]
25 480 2500
15 560 2800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 20 100
Tab 2
42

Rightangle - Gear
95Nm 503
weight 4.20 kg
56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5

56B14 K030.4.046 80 61.5
63B14 K030.4.045 90 62.5
Type B 82 98.5 3.5 123 63 113 138.5 163 ø10.5 K050.9.022
Type S 85 96 10 114 85 110 139.5 166 ø10 KS050.9.023

kit cod. K050.9.027

+0,20 1) K050.9.010
FC 70 +0,15 9 12 85 44.5 90 123 10.5
2) - Single Shaft
+0,20 1) K050.9.010
FL 70 +0,15 9 12 114.5 74 90 123 10.5
2) K050.0.200
+0,20 1) KS050.9.012
F1 110 +0,15 4 11 83.5 43 130 160 10
2) -
+0,20 1) KS050.9.014
F2 70 9 12 76.5 36 90 123 10.5
+0,15 2) -
+0,035 1) KS050.9.013
F3 95 4 10 66.5 26 115 140 10
0 2) -

1) K030.5.006 PAM63 -0,005
type B 9 h6 10.2 3 20 58 - type B 8 52 25 59.5 81 200 86.5 146 28 M8x20
2) - -0,020
1) - -0,005
type S - - - - - - type S 8 50 24 68.5 81 218 86.5 155 27 M8x20
2) - -0,020
43
Worm
Worm
GearGear
Boxes
Boxes Chapter
Chapter
7 7
Combined
Combined
WormWorm
Gear Gear
Unit Unit
633633
Rightangle
Rightangle
200Nm200Nm
- Gear-063+030
Gear 063+030
Rating Rating Alluminium
Alluminium
• QUICK
• QUICK
SELECTION
SELECTION
-1 -1
input speed
input speed
(n 1)=1400
(n 1)=1400
min min
OutputOutput Motor Motor

OutputOutput
ServiceService
NominalNominal
Nominal Nominal
Available
Available AvailableAvailableDynamic Dynamic
Tooth Tooth
Ratio Ratio
speed speed powerpower
torquetorque
factor factor
powerpower
torquetorque
B5 motor
B5 motor
flangesflanges
B14 motor
B14 motor
flangesflanges
effiency
effiency
Module Module
n2 n2 P P1MM2M M2M P P1R M2R M2R A A B B O O P P Ratios Ratios
-1 -1 i i 1M f.s f.s 1R RD RD [mm]
Mn Mn [mm]
[min ] [min ] [kW] [kW]
[Nm] [Nm] [Nm] [Nm]56
[kW] [kW] 56 63 63 56 56 63 63 code code
5.6 5.6252 2520.18 0.18142 1421.4 1.40.25 0.25200 200 B B B- C B- C 46 46 2.7 2.7 01 01
3.9 3.9360 3600.18 0.18181 1811.1 1.10.20 0.20200 200 B B B- C B- C 41 41 2.7 2.7 02 02
2.6 2.6540 5400.12 0.12164 1641.2 1.20.15 0.15200 200 B B B- C B- C 37 37 2.7 2.7 03 03
1.9 1.9720 7200.12 0.12200 2001.0 1.00.12 0.12200 200 B B B- C B- C 34 34 2.7 2.7 04 04
1.3 1.31080 10800.12 0.12265 2650.8 0.80.09 0.09200 200 B B B- C B- C 30 30 2.7 2.7 05 05
1.0 1.01440 1440
0.12* 0.12*
200 200<0.8 <0.8 0.08 0.08200 200 B B B- C B- C 27 27 2.7 2.7 06 06
0.5 0.52745 2745
0.12* 0.12*
200 200<0.8 <0.8 0.05 0.05200 200 B B B- C B- C 23 23 2.1 2.1 07 07
Motor Flanges
Motor Flanges
Available
Available
B) Supplied
B) Supplied
with Reduction
with Reduction B) Available
BushingBushing B) Available
on Request
on Request
without reduction
without reduction
bushingbushing
C) MotorC)Flange
Motor Holes
FlangePosition
Holes Position
* Power* higher
Power than
higher
thethan
maximum
the maximum
one which
onecan
which
becan
supported
be supported
by the gearbox.
by the gearbox.
Select according
Select according
to the torque
to the torque
M2R M2R
Unit 633Unit
is supplied
633 is supplied
with synthetic
with synthetic
oil, providing
oil, providing
“long “long
life” lubrication.
life” lubrication.
For mounting
For mounting
positionposition
V5- V6 V5-
please
V6 please
contactcontact
us. us. LUBRICATION
LUBRICATION
633 OIL
633 OIL
Quantity
Quantity
0.40/0.06
0.40/0.06
Lt Lt
See table
See1 table
for lubrication
1 for lubrication
and recommended
and recommended
quantity.
quantity.
In tableIn2 table
please
2 please
see possible
see possible
radial loads
radialand
loads
axial
and axial
loads onloads
the gearbox.
on the gearbox. AGIP AGIP KLUBER
KLUBER SHELL SHELL MOBILMOBIL
Telium VSF
Telium
320VSF
Syntheso
320 Syntheso
D220 EPD220
Tivela
EP Oil
Tivela
WB Oil
Glygoyl
WB Glygoyl
30 SHC30
630
SHC 630

Tab 1 Tab 1
RADIAL
RADIAL
AND AND
AXIALAXIAL
LOADSLOADS
n2 n2
FA FR
FA FR
Output
Output
Shaft Shaft [min-1][min-1]
[N] [N]
[N] [N]
25 25
700 3800
700 3800
15 15
800 4000
800 4000
InputInput
Shaft Shaft
n2 n2
FA FR
FA FR
[min-1][min-1]
[N] [N]
[N] [N]
1400 1400
20 100
20 100
*Strong axial
*Strong
loads
axial
inloads
the DX
indirection
the DX direction
are not allowed.
are not allowed.
Tab 2 Tab 2
44 44

Rightangle - Gear
200Nm 633
weight 7.50 kg
56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5

56B14 K030.4.046 80 61.5
63B14 K030.4.045 90 62.5
Type B 100 111 4 144 95 133 170 200 ø10.5 K063.9.022
Type S - - - - - - - - - -

kit cod. K063.9.027

+0,20 1) K063.9.010
FC 115 +0,15 7 13 86 26 150 175 11
2) - Single Shaft
+0,20 1) K063.9.010
FL 115 +0,15 7 13 116 56 150 175 11
2) K063.0.200
+0,20 1) KS070.9.013
F1 130 +0,15 7 13 102 42 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS063.9.011
F3 110 5 11 82 22 130 160 10
0 2) -
b1 c1 d1 e1 f1 l1 m1 n1 t2 o1
ød e g l m x kit code -0,005
type B 8 60 25 63.2 120 246.4 126.8 190 28 M8x20
1) K030.5.006 PAM63 -0,020
type B 9 h6 10.2 3 20 58 -
2) - type S - - - - - - - - - -
1) -
type S - - - - - -
2) -
45

230Nm
Rating Alluminium
Input speed (n 1) = 1400min

• QUICK SELECTION -1
Output Motor Output Service Nominal Nominal Available B5 Available B14 motor Dynamic Tooth
Ratio
Speed power torque factor power torque motor flanges flanges efficiency Module
-1 i f.s. RD
5.6 252 0.18 142 1.6 0.29 230 B B- C B- C 46 2.7 01
3.9 360 0.18 186 1.2 0.22 230 B B- C B- C 42 2.7 02
2.8 504 0.12 161 1.4 0.17 230 B B- C B- C 39 2.7 03
1.9 756 0.12 204 1.1 0.14 230 B B- C B- C 33 2.7 04
1.4 1008 0.12 256 0.9 0.11 230 B B- C B- C 31 2.7 05
1.1 1332 0.12* 230 <0.8 0.08 230 B B- C B- C 30 2.7 06
0.8 1656 0.12* 230 <0.8 0.07 230 B B- C B- C 28 2.7 07
0.6 2160 0.12* 230 <0.8 0.06 230 B B- C B- C 26 2.7 08
0.6 2520 0.12* 230 <0.8 0.05 230 B B- C B- C 25 2.7 09

life” lubrication. For mounting position V5- V6 please LUBRICATION 634 OIL
contact us.
Tab 1
n2 FA FR
25 700 3800
15 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 42 210
Tab 2
46

Rightangle - Gear
230Nm 634
8.90 kg
weight
63B5 K050.4.041 138 72
71B5 K050.4.042 160 70

56B14 K040.4.049 80 71.5
63B14 K050.4.047 90 74
71B14 K050.4.045 105 71.5
Type B 100 111 4 144 95 133 170 200 ø10.5 K063.9.022
Type S - - - - - - - - - -

kit cod. K063.9.027

+0,20 1) K063.9.010
FC 115 +0,15 7 13 86 26 150 175 11
2) - Single Shaft
+0,20 1) K063.9.010
FL 115 +0,15 7 13 116 56 150 175 11
2) K063.0.200
+0,20 1) KS070.9.013
F1 130 +0,15 7 13 102 42 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS063.9.011
F3 110 5 11 82 22 130 160 10
0 2) -
1) K045.5.006 PAM71 -0,005
type B 11 h6 12.5 4 30 68 - type B 8 60 25 63.2 120 246.4 126.8 190 28 M8x20
2) - -0,020
1) - type S - - - - - - - - - -
type S - - - - - -
2) -
47
6A3 Rightangle - Gear 63A +030

252Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s RD Mn [mm]
5.6 252 0.18 142 1.8 0.32 252 B B- C 46 2.7 01
3.9 360 0.18 181 1.4 0.25 252 B B- C 41 2.7 02
2.6 540 0.12 164 1.5 0.18 252 B B- C 37 2.7 03
1.9 720 0.12 200 1.3 0.15 252 B B- C 34 2.7 04
1.3 1080 0.12 265 1.0 0.11 252 B B- C 30 2.7 05
1.0 1440 0.12 318 0.8 0.10 252 B B- C 27 2.7 06
0.5 2745 0.12* 210 <0.8 0.05 210 B B- C 23 2.1 07
Unit 6A3 is supplied with synthetic oil, providing “long

contact us. LUBRICATION 6A3 OIL

Tab 1
n2 FA FR
25 700 3800
15 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 20 100
Tab 2
48

Rightangle - Gear
252Nm 6A3
P6A3FB... Basic wormbox Wormbox
weight 8.90 kg
56B5 K030.4.041 120 61.5
63B5 K030.4.042 140 62.5

56B14 K030.4.046 80 61.5
63B14 K030.4.045 90 62.5
P6A3PA... Feet P6A3PB... Feet P6A3PV... Feet
Type B 115 115 12 142 120 156 185 215 ø11 K070.9.022
Type S - - - - - - - - - -
P6A3FC... Output flange P6A3BR... Reaction arm

kit cod. K063.9.027

+0,20 1) K070.9.010
P6A3..S... P6A3..D... Double Shaft
FC 130 +0,15 7 13 85 25 165 200 13
2) - Single Shaft
+0,20 1) K070.9.010
FL 130 +0,15 7 13 111 51 165 200 13
2) K070.0.200
+0,20 1) KS070.9.014
F1 130 +0,15 7 13 111 51 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
3) -
+0,035 1) KS070.9.011
F3 110 5 13.5 84.5 24.5 130 160 11
0 2) -
R6A3FB... Input shaft
1) K030.5.006 PAM63 -0,005
type B 9 h6 10.2 3 20 58 - type B 8 60 28 63.5 120 247 127.5 191 31 M8x20
2) - -0,020
1) - type S - - - - - - - - - -
type S - - - - - -
2) -
49
6A4 Rightangle - Gear 63A +045

264Nm
Rating Alluminium

Ratio
-1 i f.s. RD
5.6 252 0.18 142 1.9 0.33 264 B B- C B- C 46 2.7 01
3.9 360 0.18 186 1.4 0.26 264 B B- C B- C 42 2.7 02
2.8 504 0.18 241 1.1 0.20 264 B B- C B- C 39 2.7 03
1.9 756 0.12 204 1.3 0.16 264 B B- C B- C 33 2.7 04
1.4 1008 0.12 256 1.0 0.12 264 B B- C B- C 31 2.7 05
1.1 1332 0.12 327 0.8 0.10 264 B B- C B- C 30 2.7 06
0.8 1656 0.12* 264 <0.8 0.08 264 B B- C B- C 28 2.7 07
0.6 2160 0.12* 264 <0.8 0.07 264 B B- C B- C 26 2.7 08
0.6 2520 0.12* 264 <0.8 0.06 264 B B- C B- C 25 2.7 09
Unit 6A4 is supplied with synthetic oil, providing “long

contact us.
LUBRICATION 6A4 OIL

Tab 1
n2 FA FR
25 700 3800
15 800 4000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 42 210
Tab 2
50

Rightangle - Gear
264Nm 6A4
P6A4FB... Basic wormbox Wormbox
weight 8.90 kg
63B5 K050.4.041 138 72
71B5 K050.4.042 160 70

56B14 KC40.4.049 80 71.5
63B14 K050.4.047 90 74
71B14 K050.4.045 105 71.5
P6A4PA... Feet P6A4PB... Feet P6A4PV... Feet
Type B 115 115 12 142 120 156 185 215 ø11 K070.9.022
Type S - - - - - - - - - -
P6A4FC... Output flange P6A4BR... Reaction arm

kit cod. K063.9.027

+0,20 1) K070.9.010
P6A4..S... P6A4..D... Double Shaft
FC 130 +0,15 7 13 85 25 165 200 13
2) - Single Shaft
+0,20 1) K070.9.010
FL 130 +0,15 7 13 111 51 165 200 13
2) K070.0.200
+0,20 1) KS070.9.014
F1 130 +0,15 7 13 111 51 165 200 13
2) -
+0,20 1) KS063.9.013
F2 115 +0,15 7 13 116 56 150 175 11
2) -
+0,035 1) KS070.9.011
F3 110 5 13.5 84.5 24.5 130 160 11
0 2) -
R6A4FB... Input shaft
1) K045.5.006 PAM71 -0,005
type B 11 h6 12.5 4 30 68 - type B 8 60 28 63.5 120 247 127.5 191 31 M8x20
2) - -0,020
1) - type S - - - - - - - - - -
type S - - - - - -
2) -
51

450Nm
Rating Alluminium

Ratio
-1 i f.s. RD
10 140 0.37 205 1.6 0.58 320 B B- C B- C 58 4.5 01
7.1 196 0.37 257 1.2 0.46 320 B B- C B- C 52 4.7 02
5.0 280 0.37 332 1.4 0.50 450 B B- C B- C 47 4.7 03
3.6 392 0.37 435 1.0 0.38 450 B B- C B- C 44 4.7 04
2.4 588 0.25 371 1.2 0.30 450 B B- C B- C 37 4.7 05
1.8 784 0.25 455 1.0 0.25 450 B B- C B- C 34 4.7 06
1.4 1036 0.18 420 1.1 0.19 450 B B- C B- C 33 4.7 07
1.1 1288 0.18 474 0.9 0.17 450 B B- C B- C 30 4.7 08
0.7 1960 0.12 449 1.0 0.12 450 B B- C B- C 28 4.7 09
0.5 2856 0.12 584 0.8 0.09 450 B B- C B- C 25 4.7 10
Unit 854 is supplied with syntetic oil, providing "long life"

lubrication. For mounting position V5- V6 please contact us. LUBRICATION 854 OIL
See table 1 for lubrication and recommended quantity
In table 2 please see possible radial loads and axial loads
on the gearbox.
Tab 1
n2 FA FR
25 1000 5000
15 1160 5800
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 42 210
Tab 2
52

Rightangle - Gear
450Nm 854
19.50 kg
weight
63B5 K050.4.041 138 72
71B5 K050.4.042 160 70

56B14 KC40.4.049 80 71.5
63B14 K050.4.047 90 74
71B14 K050.4.045 105 71.5
Type B 142 145 5 182 140 180 236.5 280 ø10.5 K085.9.022
Type S - - - - - - - - - -
kit cod. K085.9.027

+0,06 1) K085.9.010
FC 152 +0,00 5 16 108 40.5 176 205 13
2) - Single Shaft
+0,06 1) K085.9.010
FL 152 +0,00 5 16 148.5 81 176 205 13
2) K085.0.201
+0,040 1) KS085.9.012
F1 130 5 13 117.5 50 165 200 11.5
0 2) -
+0,06 1) KS085.9.013
F2 152 5 15 147.5 80 180 205 12.5
0 2) -
+0,040 1) KS085.9.015
F3 130 5 13 106.5 39 165 200 13
0 2) -
1) K045.5.006 PAM71 -0,005
type B 11 h6 12.5 4 30 68 - type B 10 60 35 73.5 135 282 141 214.5 38 M10x23
2) - -0,020
1) - type S - - - - - - - - - -
type S - - - - - -
2) -
53

850Nm
Rating Alluminium
• QUICK SELECTION
-1
Ratio
-1 i f.s 100 100 RD
112 112
6,7 210 0,75 591 1,3 0,95 750 B B B- C B- C B 55 5,6 01
4,7 300 0,75 752 1,1 0,85 850 B B B- C B- C B 49 5,6 02
3,3 420 0,55 741 1,1 0,63 850 B B B- C B- C B 47 5,6 03
2,6 540 0,55 851 1,0 0,55 850 B B B- C B- C B 42 5,6 04
1,8 780 0,37 748 1,1 0,42 850 B B B- C B- C B 38 5,6 05
1,3 1080 0,25 681 1,2 0,31 850 B B- C B- C 37 5,6 06
1,1 1290 0,25 770 1,1 0,28 850 B B- C B- C 35 5,6 07
0,8 1800 0,25 921 0,9 0,23 850 B B- C B- C 30 5,6 08
0,7 2040 0,18 751 1,1 0,20 850 B B- C B- C 30 5,6 09
0,6 2400 0,18 825 1,0 0,19 850 B B- C B- C 28 5,6 10
0,5 3000 0,12 638 1,3 0,16 850 B B- C B- C 26 5,6 11
Unit 115 is supplied without lubricant and equipped with a

breather, level and drain plugs. User can add mineral oil
keeping existing plugs.
Should the user wish to fill it with synthetic oil, it is

recommended to replace the existing plugs with a type that
are closed.
Gearbox 050 is supplied lubricated for life. AGIP KLUBER SHELL MOBIL
See tab.1 for oils and recommended quantity.
Tab 1
In tab.2 there are radial loads and axial loads applicable to
the gearbox.

[min-1] [N] [N]
25 1200 6000
15 1400 7000
Input Shaft
n2 FA FR
[min-1] [N] [N]
1400 76 380
Tab 2
54

Rightangle - Gear
850Nm 115
weight 38.00 kg
63B5 K050.4.041 138 76.5
71B5 K050.4.042 160 74.5
80B5 K050.4.043 200 76.5
56B14 KC40.4.049 80 76
63B14 K050.4.047 90 78.5
71B14 K050.4.045 105 76
80B14 K050.4.046 120 76.5
Type B 170 180 22 224 200 240 286 333 ø13 K110.9.022
Type S 172 160 18 190 200 240 288 335 ø14 KS110.9.023

kit cod. K110.9.027

+0,083 1) K110.9.010
FC 170 +0,043 11 16.5 131.5 54 230 270 13
2) - Single Shaft
+0,083 1) K110.9.011
FL 170 +0,043 11 16.5 179.5 102 230 270 13
2) -
+0,040 1) KS110.9.014
F1 180 5 18 150 72.5 215 250 15
0 2) -
+0,083 1) KS110.9.012
F2 170 +0,043 9.5 15 178 100.5 230 270 13
2) -
+0,040 1) KS110.9.013
F3 180 5 18 130 52.5 215 250 15
0 2) -
1) K050.5.006 PAM71 -0,005
type B 16 h6 18 5 30 74.5 M6x16 type B 12 75 42 96.5 155 348 163.5 260 45 M12x32
2) K050.5.007 PAM80 -0,020
1) KS050.5.008 PAM71 type S - - - - - - - - - -
type S 14 h6 16 5 30 74.5 M5x10
2) KS050.5.009 PAM80
55
Product News
Square Worm Gear Boxes
For tables and prices, please look up on www.lonne.com or contact Lönne staff.
56
Product News
Hightech Worm Gear Boxes
High Quality precision machining & low

friction bronze Wide housing and strong
output bearings.
57
Product News
Stainlesssteel Worm and Coaxial Gear Boxes
Worm Gear Box
Coaxial Gear Box
58
Innledning Bibel rev 3 (vår 2012)
Important addresses and phone numbers

NORWAY
Bergen Lönne Scandinavia AS Phones/ Faxes
Postal address: Visit address ph: +47 55 39 10 00
Postboks 144 Ulset Liamyrane12, fax: +47 55 39 11 00
N-5873 BERGEN N-5132 NYBORG 24- h.service: +47 918 33 073
Oslo: Lönne Scandinavia AS Phones/ Faxes

Postal and visit address: Frysjaveien 40 ph: +47 22 02 10 30
N-0884 OSLO fax: +47 22 02 10 50
Ålesund: Lönne Scandinavia AS Phones/ Faxes

Postal address: Visit address:
Po.Box 7892 Spjelkavikveien 9 ph: +47 70 15 39 00
6022 Ålesund N-6011 ÅLESUND fax: +47 70 15 39 01
SWEDEN
Helsingborg Lönne Scandinavia AB Phones/ Faxes
Postal and visit address: Kastellgatan 5 ph +46(0)42 38 03 00
S-254 66 HELSINGBORG fax: +46(0)42 38 03 09
24- h. service: +46 (0) 70 885 5431
Stockholm: Lönne Scandinavia AB Phones/ Faxes

Postal and visit address: Lovisagatan 4 ph: +46-8 662 62 85
S-115 23 STOCKHOLM fax: +46-8 545 697 20
FINLAND
Helsinki Lönne Scandinavia OY Phones/ Faxes
Postal and visit address: Hernepellontie 11Service phone: +358 50 570 4070 ph: +358(0)9342 4300
FI-00710 HELSINKI fax: +358(0)9342 43099
Service phone: +358 50 570 4070
DENMARK
Vejle Lönne Scandinavia AS Phones/ Faxes
Postal and visit address: Bugattivej 5G ph: +45 76 40 87 00
.............................................DK-7100 VEJLE fax: +45 76 40 87 01
24- h. service: +45 24 45 74 03
Lönne Service Main Office

Solgaard Skog 7, P.O. Box 460, N-1502 MOSS, Norway. www
Telephone +47 69 24 40 00 Fax +47 69 24 07 45
24- h. service +47 924 32 085
Price Policy Environmental Protection - Information

Prices occur in special lists on requirement in specified currency, ex Requirement
warehouse exclusive packaging. The sales tax (value added tax) is Electric and electronic products, so- called EE products may contain
not included in the prices. It shall be debited separately at the toxins which can damage our health and the environment.
respective rate according to the applicable legal regulations. Therefore, all importers and producers of EE products are obliged to
take responsibility for their products until they have been scrapped
and recycled. You may return any cast- off Lönne products to a
Terms of Sales and Delivery Lönne Warehouse. Lönne is obliged to fulfil the authorities’
Terms of Sales and delivery are specified on our web site; requirements regarding an environmentally sound handling of EE-
www.lonne.com waste in accordance with the EE regulations.
Lönne Scandinavia AS reserves the prohibition to publish pages or

whole parts of this catalogue without athorization. General
Export and Import Regulations regarding Lönne Product Range of
Drives and Controls will be subject to the Export Import Regulations
actual in the area of delivery. We hereby reserve the right to change
the content of data in this catalogue at any time without notice.
Furthermore, our company shall not be held responsible for neither
possible discrepancies in catalogue content nor any damage
caused by wrong use of products or information.
6
59
Products | Solutions | Services
Lönne Main Catalogue Chapters: Lönne

Lönne Scandinavia AS was founded in 1949 in Bergen,
Chapter 1 Electric Motors Norway. Present board member Mr Terje Lönne entered as
Chapter 2 Generators second generation, and started the expansion into the
Chapter 3 ECOiPM PM Motors Nordic market.
Chapter 4 Frequency Inverters
Lönne has specialized within electric motors, generators,
Chapter 5 Servo Controls
frequency inverters, gearboxes, transmissions and
Chapter 6 Machine Controls bearings. Lönne reference list covers a wide range of
Chapter 7 Worm Gear Boxes customers within on shore, off shore, maritime and marine
Chapter 8 Helical Gear Boxes industries.
Chapter 9 Torque Arm Speed Reducers Step by step the company has grown to become a
Chapter 10 Planetary Gear Boxes leading, Nordic supplier within drive technology.
Chapter 11 V-belt and V-belt Pulleys Lönne one stop shop concept is a strong force for
Chapter 12 Timing Belt and Timing Belt Pulleys customers whom operate the total value chain of drive
technology components.
Chapter 13 Chains and Sprockets
Lönne is today widely recognized both as a supplier of high
Chapter 14 Couplings
quality components and engineered solutions.
Chapter 15 Clamping Elements
Chapter 16 Disk Brakes Lönne head quarter is located in Bergen, Norway, with
Chapter 17 Bearings subsidiaries in Denmark, Finland and Sweden. The central
Chapter 18 Vibrators warehouse, workshop and testing department in
Helsingborg provides quick delivery service overnight, to
the Nordic market. Smaller express warehouses and
workshops are also located in Bergen and Helsinki. See
map on the back page for the total Lönne Group.
Lönne Service is a separate part of the Lönne Group. With

a total of six workshops in Norway, Lönne Service is
specializing in services and repairing of electric motors and
generators, both towards on shore and off shore markets.
Lönne Service is ranked to have one of the market's largest
and most updated machine parks, operated by highly
skilled personnel.
Lönne people take pride in every job done, with a high

level of professionalism, and really care to
”keep your machinery running!”
Lönne Quality Management System Standards is certified

for ISO 9001:2008.
For further information, please have a look at our website
or feel free to call us!
Norway Sweden Denmark Finland

Head Office
Lönne Scandinavia AS Lönne Scandinavia AB Lönne Scandinavia AS Lönne Scandinavia OY
Liamyrane 12, Bergen Kastellgatan 5 Bugattivej 5G Hernepellontie
N-5132 Nyborg Bergen S-254 66 Helsingborg DK-7100 Vejle FI-00560 Helsinki
Tel: +47 55 39 10 00 Tel: +46 (0) 42 38 03 00 Tel: +45 (0) 76 40 87 00 Tel: +358 (0) 9 342 4300
Fax: +47 55 39 11 00 Fax: +46 (0) 42 38 03 09 Fax: +45 (0) 76 40 87 01 Fax: +358 (0) 9 3424 3099
Local mail: [email protected] Local mai: [email protected] Local mail: [email protected] Local mai: [email protected]
24-h. service: +47 91 83 30 73 24-h. service: +46 (0) 70 88 55 43 1 24-h. service: +45 (0) 24 45 74 03

Worm Gear Boxes PDF

Uploaded by

Copyright:

Available Formats

Worm Gear Boxes PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Worm Gear Boxes PDF

Uploaded by

Copyright:

Available Formats

What are worm gear boxes used for?

What are worm gear boxes used for?

What are the different types of worm gear boxes described?

What are the different types of worm gear boxes described?

Products | Solutions | Service

Worm Gear Boxes Chapter 7

General Product Overview 5

Worm Gear Boxes Product Spectre

WORM Size 030 - 110 Single stage worm gearboxes. A simple

Single stage unit with helical primary

Two single stage units combined together.

WORM Torque : 30 - 850 Nm

Output hollow shaft : 14 - 42 mm

Single piece alloy steel

Vent Free Design.

Worm Gear Sizes and Torques

Types 030 045 050 063 63A 085 110

Use our web database

Worm Gear Boxes Codification

Type Size Mounting

Worm gearboxes with primary reduction

Combined worm gearboxes

On request can deliver our products according to the ATEX

Worm Gear Boxes Codification

Motor Terminal box Mounting Reduced input Mounting

Lifting P [kW] = M [Kg] •g [9.81] • v [m/ s]

Rotation P [kW] = M [Nm] •n [rpm]

Linear movement P [kW] = F [N] •v [m/ s]

M [Nm] = 9550 •P[KW]

M [lb in] = 63030 • P[HP]

FR [N] = M [Nm] •2000 •fk FR [N] = M [lb in] • 8.9 •fk

d Diam. of driving element

Factor / Coefficiente di trasformazione / Faktor / Coefficiente de transmisión

How to select a Worm Gear Box

045 Rightangle - Gear

Output Nominal Nominal Dynamic

C Ratio Nominal module Notes

Transmitted torque Service factor

A Select required torque (according to service factor)

B Select ouput speed

D Select motor flange available (if requested)

Single Worm Gear Boxes 030

030 Rightangle - Gear

n2 P1M M2M P1R M2R A B O P Ratios

280 5 0.18 5 3.2 0.57 16 B B- C 82 1.26 01

Unit 030 is supplied with synthetic oil, providing

RADIAL AND AXIAL LOADS

*Strong axial loads in the DX direction are not allowed.

Single Worm Gear Boxes 030

M. flanges Kit code øF A

56B14 K030.4.046 80 61.5

P030PA... Feet P030PB... Feet P030PV... Feet

P030FC... Output flange P030BR... Reaction arm

Type B øD E G L N O P Q Kit code

R030FB... Input shaft

kit cod. K030.5.028 type B kit cod. K030.5.029 type B

Worm Gear Boxes 045

045 Rightangle - Gear

n2 P1M M2M P1R M2R B C O P Q Ratios