2012 Grand - Caravan OM 3rd PDF

2012 Grand Caravan
2012 Grand Caravan

OWNERS MANUAL
Chrysler Group LLC
12Y532-126-AA First Edition Printed in U.S.A.
903656_Grand Caravan_OM cover.indd 1 3/15/11 10:41 AM

VEHICLES SOLD IN CANADA
With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of
Chrysler Group LLC shall be deemed to be deleted and the features and equipment that are either standard or optional
name Chrysler Canada Inc. used in substitution therefore. on this vehicle. This manual may also include a description
of features and equipment that are no longer available or
DRIVING AND ALCOHOL were not ordered on this vehicle. Please disregard any
Drunken driving is one of the most frequent causes of features and equipment described in this manual that are
accidents. not on this vehicle.
Your driving ability can be seriously impaired with blood
alcohol levels far below the legal minimum. If you are Chrysler Group LLC reserves the right to make changes in
drinking, dont drive. Ride with a designated non-drinking design and specifications, and/or make additions to or
driver, call a cab, a friend, or use public transportation. improvements to its products without imposing any obliga-
tion upon itself to install them on products previously
manufactured.
WARNING!
Driving after drinking can lead to an accident. Your
perceptions are less sharp, your reflexes are slower,
and your judgment is impaired when you have been
Copyright 2011 Chrysler Group LLC
drinking. Never drink and then drive.
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this The antenna cable should be as short as practical and
vehicles electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use
frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
equipment must be installed properly by trained personnel.
Carefully match the antenna and cable to the radio to
The following must be observed during installation.
ensure a low Standing Wave Ratio (SWR).
The positive power connection should be made directly to
Mobile radio equipment with output power greater than
the battery and fused as close to the battery as possible.
normal may require special precautions.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection. All installations should be checked for possible interfer-
This connection should not be fused. ence between the communications equipment and the
vehicles electronic systems.
Antennas for two-way radios should be mounted on the roof
or the rear area of the vehicle. Care should be used in
mounting antennas with magnet bases. Magnets may affect
the accuracy or operation of the compass on vehicles so
equipped.
SECTION TABLE OF CONTENTS PAGE
1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1
2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 2
3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 3
4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 279 4
5 STARTING AND OPERATING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415 5
6 WHAT TO DO IN EMERGENCIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 511 6
7 MAINTAINING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 541 7
8 MAINTENANCE SCHEDULES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 589 8
9 IF YOU NEED CONSUMER ASSISTANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 605 9
10 INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 615 10
INTRODUCTION
1
CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vehicle Identification Number .............. 6
How To Use This Manual . . . . . . . . . . . . . . . . . . 4 Vehicle Modifications/Alterations . . . . . . . . . . . . 7
Warnings And Cautions . . . . . . . . . . . . . . . . . . . 6
4 INTRODUCTION
INTRODUCTION When it comes to service, remember that your authorized
Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech-
LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about
workmanship, distinctive styling, and high quality - all your satisfaction.
essentials that are traditional to our vehicles.
HOW TO USE THIS MANUAL
This Owners Manual has been prepared with the assis- Consult the Table of Contents to determine which section
tance of service and engineering specialists to acquaint contains the information you desire.
you with the operation and maintenance of your vehicle.
It is supplemented by Warranty Information, and various Since the specification of your vehicle depends on the
customer-oriented documents. Please take the time to items of equipment ordered, certain descriptions and
read these publications carefully. Following the instruc- illustrations may differ from your vehicles equipment.
tions and recommendations in this manual will help The detailed index at the back of this Owners Manual
assure safe and enjoyable operation of your vehicle. contains a complete listing of all subjects.
NOTE: After reviewing the owner information, it Consult the following table for a description of the
should be stored in the vehicle for convenient referenc- symbols that may be used on your vehicle or throughout
ing and remain with the vehicle when sold. this Owners Manual:
INTRODUCTION 5
6 INTRODUCTION
WARNINGS AND CAUTIONS
This Owners Manual contains WARNINGS against op-
erating procedures that could result in a collision or
bodily injury. It also contains CAUTIONS against proce-
dures that could result in damage to your vehicle. If you
do not read this entire manual, you may miss important
information. Observe all Warnings and Cautions.
VEHICLE IDENTIFICATION NUMBER

The Vehicle Identification Number (VIN) is found on the
left front corner of the instrument panel, visible through
the windshield. This number also appears stamped on
the right sliding door sill under the sill moulding and Vehicle Identification Number
printed on the Automobile Information Disclosure Label
affixed to a window on your vehicle, the vehicle regis-
tration and title.
INTRODUCTION 7
VEHICLE MODIFICATIONS/ALTERATIONS
WARNING!
1
Any modifications or alterations to this vehicle could
seriously affect its roadworthiness and safety and
may lead to a accident resulting in serious injury or
death.
Stamped VIN Location

NOTE: It is illegal to remove or alter the VIN.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
CONTENTS 2
A Word About Your Keys . . . . . . . . . . . . . . . . . 12 Remote Starting System If Equipped . . . . . . . 29

Wireless Ignition Node (WIN) . . . . . . . . . . . . 12 How To Use Remote Start . . . . . . . . . . . . . . . 29
Sentry Key . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Replacement Keys . . . . . . . . . . . . . . . . . . . . . 16 Manual Door Locks . . . . . . . . . . . . . . . . . . . 32
Vehicle Security Alarm If Equipped . . . . . . . . 17 Power Door Locks If Equipped . . . . . . . . . 34
Rearming Of The System . . . . . . . . . . . . . . . . 17 Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Illuminated Entry If Equipped . . . . . . . . . . . 19 Power Vent Windows If Equipped . . . . . . . 36
Remote Keyless Entry (RKE) If Equipped . . . 20 Power Windows . . . . . . . . . . . . . . . . . . . . . . 36
Using The RKE Transmitter . . . . . . . . . . . . . . 20
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Sliding Side Door . . . . . . . . . . . . . . . . . . . . . . 41 Supplemental Active Head Restraints
(AHR) If Equipped . . . . . . . . . . . . . . . . . . 64
Power Sliding Side Door If Equipped . . . . . 42
Enhanced Seat Belt Use Reminder System
Sliding Side Door Child Protection Lock . . . . . 46
(BeltAlert) . . . . . . . . . . . . . . . . . . . . . . . . . 68
Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Seat Belt Lock Out . . . . . . . . . . . . . . . . . . . . 69
Power Liftgate If Equipped . . . . . . . . . . . . 49
Seat Belts And Pregnant Women . . . . . . . . . . 69
Occupant Restraints . . . . . . . . . . . . . . . . . . . . . 52
Seat Belt Extender . . . . . . . . . . . . . . . . . . . . . 70
Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . 56
Supplemental Restraint System (SRS)
Seat Belts In Passenger Seating Positions . . . . . 62 Air Bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Automatic Locking Retractor Mode (ALR) Air Bag System Components . . . . . . . . . . . . . 72
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 62
Advanced Front Air Bag Features . . . . . . . . . . 73
Energy Management Feature . . . . . . . . . . . . . 63
Air Bag Deployment Sensors And Controls . . . 76
Seat Belt Pretensioners . . . . . . . . . . . . . . . . . 64
Event Data Recorder (EDR) . . . . . . . . . . . . . . 83
Child Restraints . . . . . . . . . . . . . . . . . . . . . . 84
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11
Commercial Cargo Vehicles (No Factory Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Installed Rear Seats) If Equipped . . . . . . . . . . 95
Transporting Passengers . . . . . . . . . . . . . . . . 99
Restraining Infants And Small Children In
Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . . . . 99 2
Commercial Cargo Vehicles . . . . . . . . . . . . . . 96
Safety Checks You Should Make Inside The
Engine Break-In Recommendations . . . . . . . . . . 98
Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Periodic Safety Checks You Should Make
Outside The Vehicle . . . . . . . . . . . . . . . . . . 103
A WORD ABOUT YOUR KEYS
Your vehicle uses a keyless ignition system. This system
consists of a Key Fob with Remote Keyless Entry (RKE)
transmitter and a Wireless Ignition Node (WIN) with
integral ignition switch. You can insert the Key Fob into
the ignition switch with either side up.
Wireless Ignition Node (WIN)
The Wireless Ignition Node (WIN) operates similarly to
an ignition switch. It has four operating positions, three
with detents and one that is spring-loaded. The detent
positions are OFF, ACC, and ON/RUN. The START
position is a spring-loaded momentary contact position.
1 OFF
When released from the START position, the switch 2 ACCESSORY
automatically returns to the ON/RUN position. 3 ON/RUN
4 START
Key Fob
The Key Fob operates the ignition switch. Insert the
square end of the Key Fob into the ignition switch located
on the instrument panel and rotate to the desired posi- 2
tion. It also contains the Remote Keyless Entry (RKE)
transmitter and an emergency key, which stores in the
rear of the Key Fob.
The emergency key allows for entry into the vehicle
should the battery in the vehicle or the RKE transmitter
go dead. The emergency key is also for locking the lower
glove compartment. You can keep the emergency key
with you when valet parking. Emergency Key Removal
To remove the emergency key, slide the mechanical latch NOTE: You can insert the double-sided emergency key
at the top of the Key Fob sideways with your thumb and into the lock cylinder with either side up.
then pull the key out with your other hand.
Removing Key Fob From Ignition
Place the shift lever in PARK. Turn the Key Fob to the
OFF position and then remove the Key Fob.
NOTE: Power window switches will also remain active
WARNING!
for up to 10 minutes after the ignition switch has been
turned to OFF, depending upon the accessory delay When leaving the vehicle, always remove the key
setting. Opening the front door will cancel this feature. fob from the ignition and lock your vehicle.
Never leave children alone in a vehicle, or with
CAUTION! access to an unlocked vehicle.
If your vehicle battery becomes low or dead, your Allowing children to be in a vehicle unattended is
Key Fob will become locked in the ignition. dangerous for a number of reasons. A child or
Do not attempt to remove the Key Fob while in others could be seriously or fatally injured. Chil-
this condition, damage could occur to the Key Fob dren should be warned not to touch the parking
or ignition module. Only remove the emergency brake, brake pedal or the shift lever.
key for locking and unlocking the doors. Do not leave the key fob in or near the vehicle, and
Leave the Key Fob in the ignition and either: do not leave the ignition in the ACC or ON/RUN
position. A child could operate power windows,
Jump Start the vehicle.
other controls, or move the vehicle.
Charge the battery.
Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
is automatic, regardless of whether the vehicle is locked
CAUTION!
or unlocked.
An unlocked car is an invitation to thieves. Always
The system uses Key Fob with factory-mated Remote
remove the Key Fob from the ignition and lock all 2
Keyless Entry (RKE) transmitter and Wireless Ignition
doors when leaving the vehicle unattended.
Node (WIN) to prevent unauthorized vehicle operation.
Therefore, only Key Fobs that are programmed to the
Key-In-Ignition Reminder
vehicle can be used to start and operate the vehicle. The
Opening the drivers door when the Key Fob is in the
system will shut the engine off in two seconds if an
ignition and the ignition switch position is OFF or ACC,
invalid Key Fob is used to start the engine.
a chime will sound to remind you to remove the key.
After turning the ignition switch to the ON/RUN posi-
NOTE: The Key-In-Ignition reminder only sounds
tion, the Vehicle Security Light will turn on for three
when the Key Fob is placed in the OFF or ACC ignition
seconds for a bulb check. If the light remains on after the
position.
bulb check, it indicates that there is a problem with the
SENTRY KEY electronics. In addition, if the light begins to flash after
The Sentry Key Immobilizer system prevents unauthor- the bulb check, it indicates that someone used an invalid
ized vehicle operation by disabling the engine. The Key Fob to start the engine. Either of these conditions will
system does not need to be armed or activated. Operation result in the engine being shut off after two seconds.
If the Vehicle Security Light turns on during normal vehicle. Once a Key Fob is programmed to a vehicle, it
vehicle operation (vehicle running for longer than 10 sec- cannot be reprogrammed to any other vehicle.
onds), it indicates that there is a fault in the electronics.
Should this occur, have the vehicle serviced as soon as CAUTION!
possible by an authorized dealer.
Always remove the Key Fobs from the vehicle and
CAUTION! lock all doors when leaving the vehicle unattended.
The Sentry Key Immobilizer system is not compat- At the time of purchase, the original owner is provided
ible with some after-market remote starting systems. with a four-digit Personal Identification Number (PIN).
Use of these systems may result in vehicle starting Keep the PIN in a secure location. This number is
problems and loss of security protection. required for authorized dealer replacement of Key Fobs.
Duplication of Key Fobs may be performed at an autho-
All of the Key Fobs provided with your new vehicle have rized dealer, this procedure consists of programming a
been programmed to the vehicle electronics. blank Key Fob to the vehicle electronics. A blank Key Fob
is one that has never been programmed.
Replacement Keys
NOTE: When having the Sentry Key Immobilizer
NOTE: Only Key Fobs that are programmed to the
system serviced, bring all vehicle Key Fobs with you to
vehicle electronics can be used to start and operate the
the authorized dealer.
Customer Key Programming provides both audible and visible signals, for the first
Programming Key Fobs or RKE transmitters may be three minutes, the headlights will turn on, the park lamps
performed at an authorized dealer. and/or turn signals will flash and Vehicle Security Light
will flash repeatedly and the horn will sound. For an 2
General Information
additional 15 minutes, only the headlights, park lamps
The Sentry Key system complies with FCC rules Part 15
and/or turn signals and Vehicle Security Light will flash.
and with RSS-210 of Industry Canada. Operation is
subject to the following conditions: Rearming Of The System
The Vehicle Security Alarm will rearm itself after the 15
This device may not cause harmful interference.
additional minutes of headlights and Vehicle Security
This device must accept any interference that may be Light flashing, if the Vehicle Security Alarm has not been
received, including interference that may cause unde- disabled. If the condition which initiated the alarm is still
sired operation. present, the Vehicle Security Alarm will ignore that
condition and monitor the remaining doors and ignition.
VEHICLE SECURITY ALARM IF EQUIPPED
The Vehicle Security Alarm monitors the vehicle doors To Arm The System
for unauthorized entry and the ignition switch for unau- Follow these steps to arm the Vehicle Security Alarm:
thorized operation. When the alarm is activated, the 1. Remove the key from the ignition system (refer to
interior switches for door locks, power sliding doors and Starting Procedures in Starting And Operating for
power liftgate are disabled. The Vehicle Security Alarm further information).
Make sure the vehicle ignition system is OFF and the Insert a valid key into the ignition switch and turn
key is physically removed from the ignition. the key to the ON position.
2. Perform one of the following methods to lock the NOTE:
vehicle: The drivers door key cylinder and the liftgate button
on the RKE transmitter cannot arm or disarm the
Press LOCK on the interior power door lock switch
Vehicle Security Alarm.
with the driver and/or passenger door open.
The Vehicle Security Alarm remains armed during
Press the LOCK button on the Remote Keyless Entry
power liftgate entry. Pressing the liftgate button will
(RKE) transmitter.
not disarm the Vehicle Security Alarm. If someone
3. If any doors are open, close them. enters the vehicle through the liftgate and opens any
door the alarm will sound.
To Disarm The System
The Vehicle Security Alarm can be disarmed using any of When the Vehicle Security Alarm is armed, the interior
the following methods: power door lock switches will not unlock the doors.
Press the UNLOCK button on the Remote Keyless The Vehicle Security Alarm is designed to protect your
Entry (RKE) transmitter. vehicle; however, you can create conditions where the
system will give you a false alarm. If one of the previ-
Cycle the vehicle ignition system out of the OFF
ously described arming sequences has occurred, the
position.
Vehicle Security Alarm will arm regardless of whether ILLUMINATED ENTRY IF EQUIPPED
you are in the vehicle or not. If you remain in the vehicle The courtesy lights will turn on when you use the
and open a door, the alarm will sound. If this occurs, Remote Keyless Entry (RKE) transmitter to unlock the
disarm the Vehicle Security Alarm. doors or open any door. 2
If the Vehicle Security Alarm is armed and the battery This feature also turns on the approach lighting in the
becomes disconnected, the Vehicle Security Alarm will outside mirrors (if equipped). Refer to Mirrors in
remain armed when the battery is reconnected; the Understanding The Features Of Your Vehicle for fur-
exterior lights will flash, the horn will sound. If this ther information.
occurs, disarm the Vehicle Security Alarm. The lights will fade to off after approximately 30 seconds,
Tamper Alert or they will immediately fade to off once the ignition
If something has triggered the Vehicle Security Alarm in switch is turned to ON/RUN from the OFF position.
your absence, the horn will sound three times and the NOTE:
exterior lights blink three times when you unlock the The front courtesy overhead console and door cour-
doors. Check the vehicle for tampering. tesy lights do not turn off if the dimmer control is in
Security System Manual Override the Dome ON position (extreme top position).
The Vehicle Security Alarm will not arm if you lock the The illuminated entry system will not operate if the
doors using the manual door lock plunger. dimmer control is in the dome defeat position
(extreme bottom position).
REMOTE KEYLESS ENTRY (RKE) IF equipped from the factory with three-button RKE trans-
EQUIPPED mitters, and those built with power options will be
This system allows you to lock or unlock the doors and equipped with up to seven-button RKE transmitters.
liftgate, and activate the Panic Alarm, optional power
Using the RKE Transmitter
liftgate, left power sliding door, and right power sliding
Three-button RKE transmitters will provide basic UN-
door from distances up to approximately 66 ft (20 m)
LOCK, LOCK and PANIC functions.
using a hand-held Key Fob with RKE transmitter. The
RKE transmitter does not need to be pointed at the
vehicle to activate the system.
NOTE: Inserting the Key Fob with RKE transmitter into
the ignition switch disables the system from responding
to any button presses from that RKE transmitter. Driving
at speeds 5 mph (8 km/h) and above disables the system
from responding to all RKE transmitter buttons for all
RKE transmitters.
Two RKE transmitters may be supplied with the vehicle.
Vehicles built without the powered options will be
Key Fob With Three-Button RKE Transmitter
Seven-button RKE transmitters will provide functions Remote Unlock Doors And Liftgate
that allow the same basic operation as the three-button, Press and release the UNLOCK button on the RKE
but may also be used to operate the power liftgate transmitter once to unlock the drivers side or twice to
(optional), power sliding doors, Remote Start feature unlock all doors and liftgate. This will also turn on the 2
(optional). Some features can be programmed to the Illuminated Entry system.
customers preferences. For example, flash headlights or
Remote Key Unlock On First Press
sound horn on LOCK.
This feature lets you program the system to unlock either
the drivers side, or all doors, on the first press of the
UNLOCK button on the RKE transmitter.
For vehicles equipped with an Electronic Vehicle In-
formation Center (EVIC), refer to Electronic Vehicle
Information Center (EVIC)/Personal Settings
(Customer-Programmable Features) in Understand-
ing Your Instrument Panel for further information.
Key Fob With Seven-Button RKE Transmitter

For vehicles not equipped with the EVIC, the Remote NOTE: Pressing the LOCK button on the RKE transmit-
Unlock feature can be enabled or disabled by perform- ter while you are inside the vehicle will activate the
ing the following steps: Vehicle Security Alarm. Opening a door with the Vehicle
Security Alarm activated will cause the alarm to sound.
1. Perform this operation while standing outside the
Press the UNLOCK button to deactivate the Vehicle
vehicle.
Security Alarm.
2. Press and hold the LOCK button on a programmed
Remote Lock Doors And Liftgate
RKE transmitter for at least 4 seconds, but no longer than
Press and release the LOCK button on the RKE transmit-
10 seconds. Then, press and hold the UNLOCK button
ter to lock all doors and liftgate. The turn signal lights
while still holding the LOCK button.
will flash and the horn will chirp to acknowledge the
3. Release both buttons at the same time. signal.
4. Test the feature while outside of the vehicle by press- Sound Horn With Remote Lock
ing the LOCK/UNLOCK buttons on the RKE transmitter This feature will cause the horn to chirp when the doors
with the ignition switch in the OFF position and the Key are locked with the RKE transmitter. This feature can be
Fob removed. turned on or turned off. To change the current setting,
proceed as follows:
5. Repeat these steps if you want to return this feature to
its previous setting. For vehicles equipped with the EVIC, refer to Elec-
tronic Vehicle Information Center (EVIC)/Personal
Settings (Customer-Programmable Features) in Un- 5. Repeat these steps if you want to return this feature to
derstanding Your Instrument Panel for further infor- its previous setting.
mation.
NOTE: Pressing the LOCK button on the RKE transmit-
For vehicles not equipped with the EVIC, perform the ter while you are in the vehicle will activate the Vehicle 2
following steps: Security Alarm. Opening a door with the Vehicle Security
Alarm activated will cause the alarm to sound. Press the
UNLOCK button to deactivate the Vehicle Security
vehicle.
Alarm.
2. Press the LOCK button on a programmed RKE trans-
Using The Panic Alarm
mitter for at least 4 seconds, but no longer than 10 sec-
To turn the Panic Alarm feature on or off, press and hold
onds. Then, press the PANIC button while still holding
the PANIC button on the RKE transmitter for at least one
the LOCK button.
second and release. When the Panic Alarm is on, the
3. Release both buttons at the same time. headlights and park lights will flash, the horn will pulse
on and off, and the interior lights will turn on.
4. Test the feature while outside of the vehicle by press-
ing the LOCK button on the RKE transmitter with the The Panic Alarm will stay on for three minutes unless
ignition switch in the OFF position and the Key Fob you turn it off by pressing the PANIC button a second
removed. time or if the vehicle is driven above 5 mph (8 km/h).
NOTE: If equipped with a rear interior switch on the left rear
When you turn off the Panic Alarm by pressing the pillar, pushing this switch once will close the liftgate only.
PANIC button a second time, you may have to move The liftgate cannot be opened from this switch.
closer to the vehicle due to the Radio Frequency (RF)
If the vehicle is locked and Vehicle Security Alarm is
noises of the system.
armed, using RKE transmitter to open the power liftgate
The Panic Alarm cannot be activated if the engine is does not unlock the vehicle or disarm the Vehicle Security
running. Alarm.
Power Open/Close Power Liftgate If Equipped Power Open/Close Left Power Sliding Door If
Press the LIFTGATE button twice on the RKE transmitter
Equipped
within five seconds to Open/Close the Power Liftgate. If
Press the LEFT Power Sliding Door button twice on the
the button is pushed while the liftgate is being power
RKE transmitter within five seconds to Power Open/
closed, the liftgate will reverse to the full open position.
Close the Left Power Sliding Door. If the button on the
RKE transmitter is pushed while the door is being
The power liftgate may also be opened and closed by
power-closed, the door will reverse to the full open
pressing the LIFTGATE button located on the overhead
position.
console.
If the vehicle is locked and the Vehicle Security Alarm is Turn Off Flash Lights With RKE Lock If
armed, pressing the LEFT Power Sliding Door button Equipped
twice unlocks the power sliding door and disarms Ve- This feature will cause the turn signal lights to flash when
hicle Security Alarm. the doors are locked or unlocked with the RKE transmit- 2
ter. This feature can be turned on or turned off. To change
Power Open/Close Right Power Sliding Door If
the current setting, proceed as follows:
Equipped
Press the RIGHT Power Sliding Door button twice on the For vehicles equipped with the EVIC, refer to Elec-
RKE transmitter within five seconds to Power Open/ tronic Vehicle Information Center (EVIC)/Personal
Close the Right Power Sliding Door. If the button on the Settings (Customer-Programmable Features) in Un-
RKE transmitter is pushed while the door is being derstanding Your Instrument Panel for further infor-
power-closed, the door will reverse to the full open mation.
position.
For vehicles not equipped with the EVIC, perform the
If the vehicle is locked and the Vehicle Security Alarm is following steps:
armed, pressing the RIGHT Power Sliding Door button
twice unlocks the power sliding door and disarms Ve-
vehicle.
hicle Security Alarm.
2. Press and hold the UNLOCK button on a programmed Programming Additional Transmitters
RKE transmitter for at least 4 seconds, but no longer than If you do not have a programmed RKE transmitter,
10 seconds. Then, press and hold the LOCK button while contact your authorized dealer for details.
still holding the UNLOCK button.
Transmitter Battery Replacement
3. Release both buttons at the same time. The recommended replacement battery is one CR2032
battery.
4. Test the feature while outside of the vehicle by press-
ing the LOCK/UNLOCK buttons on the RKE transmitter NOTE:
with the ignition switch in the OFF position and the Key Perchlorate Material special handling may apply.
Fob removed. See www.dtsc.ca.gov/hazardouswaste/perchlorate
5. Repeat these steps if you want to return this feature to Do not touch the battery terminals that are on the back
its previous setting. housing or the printed circuit board.
NOTE: Pressing the LOCK button on the RKE transmit- 1. Remove the emergency key by sliding the mechanical
ter while you are in the vehicle will activate the Vehicle latch at the top of the RKE transmitter sideways with
Security Alarm. Opening a door with the Vehicle Security your thumb and then pull the key out with your other
Alarm activated will cause the alarm to sound. Press the hand.
UNLOCK button to deactivate the Vehicle Security
Alarm.
Emergency Key Removal Inserting Emergency Key Into Slot

2. Insert the tip of the emergency key or a #2 flat blade
screwdriver into the slot and gently pry the two halves of
the RKE transmitter apart. Make sure not to damage the
seal during removal.
4. To assemble the RKE transmitter case, snap the two
halves together.
General Information
This device complies with Part 15 of the FCC rules and
RSS 210 of Industry Canada. Operation is subject to the
following conditions:
This device must accept any interference received,
including interference that may cause undesired
operation.
Separating RKE Transmitter If your RKE transmitter fails to operate from a normal
3. Remove and replace the battery. When replacing the distance, check for these two conditions.
battery, match the + sign on the battery to the + sign on
1. A weak battery in the RKE transmitter. The expected
the inside of the battery clip, located on the back cover.
life of the battery is approximately three years.
Avoid touching the new battery with your fingers. Skin
oils may cause battery deterioration. If you touch a 2. Closeness to a radio transmitter such as a radio station
battery, clean it with rubbing alcohol. tower, airport transmitter, and some mobile or CB radios.
REMOTE STARTING SYSTEM IF EQUIPPED Doors closed
This system uses the Remote Keyless Entry
Hood closed
(RKE) transmitter to start the engine conve-
niently from outside the vehicle while still Liftgate closed 2
maintaining security. The system has a range of
Hazard switch off
approximately 300 ft (91 m).
Brake switch inactive (brake pedal not pressed)
NOTE:
The vehicle must be equipped with an automatic Ignition key removed from ignition switch
transmission to be equipped with Remote Start.
Battery at an acceptable charge level
Obstructions between the vehicle and the Key Fob
RKE PANIC button not pressed
may reduce this range.
System not disabled from previous remote start event
How To Use Remote Start
All of the following conditions must be met before the Vehicle theft alarm not active
engine will Remote Start:
Shift lever in PARK
Remote Start Aborted Hood Ajar
WARNING!
Remote Start Aborted Fuel Low
Do not start or run an engine in a closed garage or
confined area. Exhaust gas contains Carbon Mon- Remote Start Aborted L/Gate Ajar
oxide (CO) which is odorless and colorless. Car-
Remote Start Disabled Start Vehicle To Reset
bon Monoxide is poisonous and can cause serious
injury or death when inhaled. The EVIC message stays active until the ignition is turned
Keep Remote Keyless Entry (RKE) transmitters to the ON/RUN position.
away from children. Operation of the Remote Start To Enter Remote Start Mode
System, windows, door locks or other controls Press and release the REMOTE START button
could cause serious injury or death. on the RKE transmitter twice within five sec-
onds. The vehicle doors will lock, the parking
Remote Start Abort Message On Electronic Vehicle lights will flash and horn will chirp twice (if
Information Center (EVIC) If Equipped programmed). Then, the engine will start and the vehicle
The following messages will display in the EVIC if the will remain in the Remote Start mode for a 15-minute
vehicle fails to remote start or exits remote start prema- cycle.
turely:
Remote Start Aborted Door Ajar
NOTE: into the ignition switch and turn it to the ON/RUN
If your power door locks were unlocked, Remote Start position, otherwise the engine will shut off at the end of
will automatically lock the doors. 15-minute cycle.
The park lights will turn on and remain on during To Exit Remote Start Mode And Drive The Vehicle 2
Remote Start mode. Before the end of the 15-minute cycle, press and release
the UNLOCK button on the RKE transmitter to unlock
For security, power window and power sunroof op-
the doors and disarm the Vehicle Security Alarm (if
eration (if equipped) are disabled when the vehicle is
equipped). Then, prior to the end of the 15-minute cycle,
in the Remote Start mode.
insert the Key Fob into the ignition switch and turn the
The engine can be started two consecutive 15-minute switch to the ON/RUN position.
cycles with the RKE transmitter. However, the ignition
NOTE:
switch must be turned to the ON/RUN position.
The ignition switch must be in the ON/RUN position
To Enter the Vehicle After Remote Start in order to drive the vehicle.
To enter the vehicle while the engine is running during a
The message Remote Start Active Key To Run
Remote Start, you must first unlock the vehicle using the
will display in the EVIC until you insert and turn the
UNLOCK button on the transmitter. After the vehicle is
key to ON/RUN position. Refer to Electronic Vehicle
unlocked, you can enter the vehicle, insert the Key Fob
Information Center (EVIC) for further information.
Cancel Remote Start NOTE: To avoid unintentional shutdowns while in the
Remote Starting will also cancel if any of the following Remote Start Mode, the system will not allow the Remote
occur: Start button to shut down the engine for two seconds
after receiving a valid Remote Start request.
The engine stalls or engine speed exceeds 2500 rpm
When To Reset Remote Start
Any engine warning lights come on
The vehicle can be started remotely up to a maximum of
Low Fuel Light turns on two times. The vehicle is also allowed a maximum of one
failed start, where the Remote Starting sequence was
The hood is opened
initiated but the engine stopped cranking without start-
The hazard switch is pressed ing. After either of these conditions, or if the Vehicle
Security Alarm system is alarming, or if the PANIC
The shift lever is moved out of PARK
button was pressed, the vehicle must be reset insert the
The engine is allowed to run for the entire 15-minute Key Fob into the ignition switch and turn the switch to
cycle the ON/RUN position.
To Turn Off The Engine While In Remote Start DOOR LOCKS
Mode
Press and release the REMOTE START button one time or Manual Door Locks
allow the engine to run for the entire 15 minute cycle. Lock the front doors by pushing down on the lock knobs
on each door trim panel.
If the lock knob is down when you shut either front door,
the door will lock. Make sure the keys are not inside the
vehicle before closing the door.
2
Sliding Door Lock
WARNING!
Manual Door Lock For personal security and safety in the event of an
If the lock knob is rearward when you shut either side accident, lock the vehicle doors as you drive as
sliding door, the door will lock. Make sure the keys are well as when you park and leave the vehicle.
not inside the vehicle before closing the door. (Continued)
WARNING! (Continued)
When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
access to an unlocked vehicle.
Allowing children to be in a vehicle unattended is
dangerous for a number of reasons. A child or
others could be seriously or fatally injured. Chil-
dren should be warned not to touch the parking
brake, brake pedal or the shift lever.
Do not leave the key fob in or near the vehicle, and
do not leave Keyless Enter-N-Go in the ACC or Driver Power Door Lock Switches
ON/RUN mode. A child could operate power win- If you press the power door lock switch while the Key
dows, other controls, or move the vehicle. Fob is in the ignition, and any front door is open, the
power locks will not operate. This prevents you from
Power Door Locks If Equipped accidentally locking your keys in the vehicle. Removing
A power door lock switch is on each front door trim the Key Fob or closing the door will allow the locks to
panel. Use this switch to lock or unlock the doors.
operate. A chime will sound if the Key Fob is in the If you press the power door lock switch while the sliding
ignition switch and a door is open, as a reminder to door is open, the sliding door will lock.
remove the Key Fob.
Automatic Door Locks If Equipped
The auto door lock feature default condition is disabled. 2
When enabled, the door locks will lock automatically
when the vehicles speed exceeds 15 mph (24 km/h). The
auto door lock feature can be enabled or disabled by your
authorized dealer per written request of the customer.
Please see your authorized dealer for service.
Unlock Doors Automatically On Exit If
Equipped
The Unlock Doors Automatically On Exit feature unlocks
all of the vehicle doors when any door is opened. This
will occur only after the shift lever has been shifted into
Front Passenger Power Door Switches the PARK position, after the vehicle has been driven (the
1 - Window Open/Close shift lever has been shifted out of PARK and all doors
2 - Power Door Locks closed).
The Unlock Doors Automatically On Exit feature will not
operate if there is any manual operation of the power
door locks (lock or unlock).
On vehicles equipped with the optional Electronic Ve-
hicle Information Center (EVIC), refer to Electronic
Vehicle Information Center (EVIC)/Personal Settings
(Customer-Programmable Features) in Understanding
Your Instrument Panel for further information.
NOTE: Use the Lock Doors Automatically at 15 mph
(24 km/h) and Unlock Doors Automatically On Exit
features in accordance with local laws.
Power Vent Window Switch Open/Close
WINDOWS Power Windows
Power Vent Windows If Equipped You can control either the front or rear windows using
The Power Vent Window Switch located on the drivers switches located on the drivers door trim panel. The
door trim panel allows the driver to operate the two vent switches will operate only when the ignition switch is in
windows from the drivers seat. the ON/RUN or ACC position and during power acces-
sory delay.
Power Window Lockout Switch If Equipped
The driver may lock out the rear power windows by
depressing the bar switch just below the power window
switches. 2
Drivers Power Window Switches

NOTE: Power Window switches will also remain active
for up to 10 minutes after the ignition switch has been
turned to OFF, depending upon the accessory delay
setting. Opening a front door will cancel this feature. Power Window Lockout Switch
Front Passenger Power Window Switch
There is a single switch on the front passengers door
trim panel which operates the passenger door window
and locks and unlocks all doors. The switch will operate
only when the ignition switch is in the ON/RUN or ACC
position and during power accessory delay.
Front Passenger Power Door Switches

1 - Window Open/Close
2 - Power Door Locks
Auto-Down Feature If Equipped To stop the window from going all the way up during the
The front window switches may be equipped with an Auto Up operation, push down on the switch briefly.
Auto-Down feature. Press the window switch past the
To close the window part way, lift the window switch to
detent, release, and the window will go down automati- 2
the first detent and release when you want the window to
cally.
stop.
To open the window part way, press the window switch
NOTE:
part way and release it when you want the window to
If the window runs into any obstacle during auto-
stop.
closure, it will reverse direction and then go back
The power window switches remain active for up to down. Remove the obstacle and use the window
10 minutes (depending on the accessory delay setting) switch again to close the window.
after the ignition switch has been turned to OFF. Opening
Any impact due to rough road conditions may trigger
a vehicle front door will cancel this feature.
the auto reverse function unexpectedly during auto-
Auto Up Feature With Anti-Pinch Protection If closure. If this happens, pull the switch lightly to the
Equipped first detent and hold to close window manually.
The front driver and front passenger switches may be
equipped with an Auto Up feature. Lift the window
switch fully upward to the second detent, release, and the
window will go up automatically.
Sliding Side Door Power Window Switch If
WARNING!
Equipped
There is no anti-pinch protection when the window Second row passengers may open and close the sliding
is almost closed. To avoid personal injury be sure to door window by a single switch on the door handle
clear your arms, hands, fingers and all objects from assembly.
the window path before closing.
The switches will operate only when the ignition switch
is in the ON/RUN or ACC position and during power
Auto Up Reset If Equipped
accessory delay.
To reactivate the Auto Up feature, perform the following
steps after vehicle power is restored: NOTE: The switches will not operate if the driver has
activated the Power Window Lockout.
1. Pull the window switch up to close the window
completely and continue to hold the switch up for an
additional two seconds after the window is closed.
2. Push the window switch down firmly to the second
detent to open the window completely and continue to
hold the switch down for an additional two seconds after
the window is fully open.
windows down, or the sunroof (if equipped) in certain
open or partially open positions. This is a normal occur-
rence and can be minimized. If the rear windows are
open and buffeting occurs, open the front and rear 2
windows together to minimize the buffeting. If the
buffeting occurs with the sunroof open, adjust the sun-
roof opening to minimize the buffeting.
SLIDING SIDE DOOR

The sliding door may be opened from the inside or the
outside. Pull outward on the exterior handle to open the
sliding door. The sliding door inside handle functions by
Sliding Door Power Window Switch rocking forward and back. Rocking the handle back-
NOTE: The sliding door windows do not fully open, wards opens the door and rocking forward releases the
stopping several inches above the window sill. hold open latch in order to close the door.
Wind Buffeting To keep your door operating properly, observe the fol-
Wind buffeting can be described as the perception of lowing guidelines:
pressure on the ears or a helicopter-type sound in the Always open the door smoothly.
ears. Your vehicle may exhibit wind buffeting with the
Avoid high impacts against the door stop when open- Power Sliding Side Door If Equipped
ing the door. This is very important when your vehicle The power sliding door may be opened or
is parked on an incline as the door will slide faster in closed manually or by using the buttons on the
the downhill direction. RKE transmitter, overhead console switch, or
rear door switch. Pulling the inside or outside
There is a hold-open latch that is activated when the
power sliding door handle will also power open or close
sliding door is fully opened. This latch will keep your
the power sliding door.
sliding door open on any incline. To close the sliding
door after the hold-open latch is activated, you must NOTE: Pulling the outside power sliding door handle a
rock the inside handle forward or pull outward on the second time while the sliding door is power opening or
exterior handle. power closing will allow the sliding door to be opened or
closed manually.
Always make sure that the sliding door is fully latched
anytime the vehicle is in motion. Press the button on the RKE transmitter twice within five
seconds to open a power sliding door. When the door is
NOTE: The left side sliding door cannot be opened
fully open, pressing the button twice within five seconds
while the fuel door is open. This feature operates only
a second time will close the door.
when the sliding door is fully closed prior to opening the
fuel door. There are power sliding side door switches located on the
b-pillar trim panel, just in front of the power sliding door
for the rear seat passengers and in the overhead console
for the driver and passengers. Pressing the switch once If the inside or outside door handles are used while the
will open the power sliding door. If the switch is pressed power sliding side door is activated, the power sliding
while the door is under a power cycle, the door will door feature will be canceled and will go into manual
reverse direction. mode. 2
NOTE: The power sliding side door must be unlocked To avoid unintentional operation of the power sliding
before the power sliding door switches will operate. doors from the rear seats, press the power sliding door
master lock button, located in the overhead console, to
disable the switches and handles for the rear seat passen-
gers.
NOTE:
The power sliding side door switches will not open if
the shift lever is in gear or the vehicle speed is above
0 mph (0 km/h). To close the power sliding door with
the shift lever in gear and vehicle speed at 0 mph
(0 km/h), the brake must be pressed.
Power Sliding Door Switch

If anything obstructs the power sliding side door
WARNING!
while it is closing or opening, the door will automati-
cally reverse to the closed or open position, provided You, or others, could be injured if caught in the path
it meets sufficient resistance. of the sliding door. Make sure the door path is clear
before closing the door.
If the power sliding side door is not in the full open or
close position, it will fully open when a power sliding
Power Sliding Side Door Open Flash
door switch is pressed. To close the door, wait until it
The left and right exterior hazard lights will flash for
is fully open and then press the switch again.
12 seconds when either sliding door is opened. This will
If the power sliding door encounters multiple obstruc- alert other drivers in the area that passenger(s) could be
tions within the same cycle, the system will automati- entering or exiting the vehicle.
cally stop, the power sliding door motor will make a
The Sliding Side Door Open Flash can be enabled or
clicking sound until the door has no further move-
disabled by performing the following procedure:
ment. This clicking sound can be stopped by pulling
the inside or outside handle. If this condition occurs, 1. Place the Key Fob in the ignition switch.
no damage is done to the power sliding door motor.
2. Cycle the ignition switch from ON/RUN to OFF five
The power sliding door must be opened or closed
times ending in the ON/RUN position (do not start the
manually.
engine).
3. Within 10 seconds of the final cycle, press the HAZ-
ARD switch ON.
4. A single chime will sound to signify that you have
successfully completed the programming. 2
You can turn the feature back on by repeating the
previous procedure.
Power Sliding Side Door Master Lock Switch
To provide a safer environment for small children riding
in the rear seats, the second row sliding door switches
and handles may be overridden by pressing the OFF side
of the Master Lock Out Switch located in the front Overhead Console Power Sliding Door Master Switch
overhead console.
1 Left Door 3 Right Door
When the power sliding door master lock switch is in the 2 Liftgate 4 Master Lock
OFF position, the power sliding side door may not be
opened or closed by pressing the switch located on the
b-pillar trim panel, just in front of the sliding door or
activating the inside power sliding door handle.
Sliding Side Door Child Protection Lock
To provide a safer environment for small children riding
in the rear seats, the sliding doors are equipped with a
Child Protection Door Lock system.
NOTE: When the Child Protection Door Lock system is
engaged, the door can be opened only by using the
outside door handle even though the inside door lock is
in the unlocked position.
To Engage the Child Protection Door Lock
1. Open the sliding side door.
2. Slide the Child Protection Door Lock control inward Child Protection Door Lock
(toward the vehicle) to engage the Child Protection Door 3. Repeat Steps 1 and 2 on the opposite sliding door.
Lock.
NOTE:
After engaging the Child Protection Door Lock, al-
ways test the door from the inside to make certain it is
in the desired position.
When the Child Protection Door Lock system is en-
WARNING!
gaged, (even if the inside door lock is in the unlocked
position) the door can be opened only by using the Avoid trapping anyone in the vehicle in a collision.
outside door handle, the RKE transmitter, the switches Remember that the sliding doors can only be opened 2
on the overhead console or the switches located on the from the outside door handle or the switches located
trim panel just in front of the power sliding door. on the trim panel just in front of the power sliding
door when the Child Protection Door Locks are
The power sliding side door will operate from the
engaged.
switches located on the trim panel just in front of the
power sliding door, regardless of the Child Protection
To Disengage the Child Protection Door Lock
Door Lock lever position. To avoid unintentional
operation of the power sliding door from the rear 1. Open the sliding side door.
seats, press the OFF Master Lock Out Switch lo-
2. Slide the Child Protection Door Lock control outward
cated in the front overhead console, next to the
(away from the vehicle) to disengage the Child Protection
driver.
Door Lock.
3. Repeat Steps 1 and 2 on the opposite sliding door (if
equipped).
NOTE: To open the liftgate, press the liftgate release handle
After setting the Child Protection Door Lock system, located on the underside of the license plate bar and pull
always test the door from the inside to make certain it the liftgate open with one fluid motion.
is in the desired position.
The power sliding side door switches will not open the
power sliding doors if the vehicle is in gear or the
vehicle speed is above 0 mph (0 km/h).
The power sliding door will operate from the outside
door handle, the RKE transmitter, the switches on the
overhead console, or the switches located on the trim
panel just in front of the power sliding door when the
shift lever is in PARK, regardless of the child lock lever
position.
LIFTGATE Liftgate Handle Location

On vehicles equipped with power locks, the liftgate can
be unlocked using the Remote Keyless Entry (RKE)
transmitter button, or by activating the power door lock
switches located on the front doors.
Power Liftgate If Equipped
The power liftgate may be opened manually or by using
the button on the Remote Keyless Entry (RKE) transmit-
ter. Press the button on the transmitter twice within five 2
seconds, to open the power liftgate. When the liftgate is
fully open, pressing the button twice within five seconds,
a second time, will close the liftgate.
The power liftgate may also be opened and closed by
pressing the button located on the overhead console.
Overhead Console Master Power Switch

1 Left Door 3 Right Door
2 Liftgate 4 Master Lock
The power liftgate may be closed by pressing the button, When the RKE transmitter button is pressed and the
located in the upper left trim in the liftgate opening. Flash Lights feature is enabled, the tail lights will flash
Pushing once will only close the liftgate. This button and several audible beeps will occur to signal that the
cannot be used to open the liftgate. liftgate is opening or closing.
WARNING!
During power operation, personal injury or cargo
damage may occur. Ensure the liftgate travel path is
clear. Make sure the liftgate is closed and latched
before driving away.
NOTE:
If anything obstructs the power liftgate while it is
closing or opening, the liftgate will automatically
reverse to the closed or open position, provided it
meets sufficient resistance.
Rear Power Liftgate Switch
There are also pinch sensors attached to the side of the The power liftgate will not operate in temperatures
liftgate opening. Light pressure anywhere along these below 12F (24C) or temperatures above 143F
strips will cause the liftgate to return to the open (62C). Be sure to remove any buildup of snow or ice
position. from the liftgate before pressing any of the power 2
liftgate buttons.
During power operation, whether liftgate is fully open
or fully closed, the liftgate chime will beep several If the power liftgate encounters multiple obstructions
times indicating power operation is in progress. within the same cycle, the system will automatically
stop and must be opened or closed manually.
The power liftgate must be in the full open or close
positions for any of the buttons to operate. If the
WARNING!
liftgate is not in the full open or close positions, it must
be opened or closed manually. Driving with the liftgate open can allow poison-
ous exhaust gases into your vehicle. You and your
If the liftgate release button is activated while the
passengers could be injured by these fumes. Keep
power liftgate is closing, the liftgate will reverse to the
the liftgate closed when you are operating the
full open position.
vehicle.
The power liftgate buttons will not operate if the shift
(Continued)
lever is in gear or the vehicle speed is above 0 mph
(0 km/h).
Supplemental Active Head Restraints (AHR) located
on top of the front seats (integrated into the head
If you are required to drive with the liftgate open, restraint) if equipped
make sure that all windows are closed, and the
climate control blower switch is set at high speed. Supplemental Driver Side Knee Air Bag
Do not use the recirculation mode. Supplemental Side Air Bag Inflatable Curtains
(SABIC) that span the front, second, and third row
Gas props support the liftgate in the open position. seating for the driver and passengers seated next to a
However, because the gas pressure drops with tempera- window
ture, it may be necessary to assist the props when
opening the liftgate in cold weather. Supplemental Seat-Mounted Side Air Bags (SAB)
An energy-absorbing steering column and steering
OCCUPANT RESTRAINTS
wheel
Some of the most important safety features in your
vehicle are the restraint systems: Knee bolsters/blockers for front seat occupant
Three-point lap and shoulder belts for all seating Front seat belts incorporate pretensioners that may
positions enhance occupant protection by managing occupant
energy during an impact event
Advanced Front Air Bags for driver and front passen-
ger
All seat belt systems (except the drivers and third row NOTE: The Advanced Front Air Bags have a multistage
center) include Automatic Locking Retractors (ALRs), inflator design. This allows the air bag to have different
which lock the seat belt webbing into position by rates of inflation based on the severity and type of
extending the belt all the way out and then adjusting collision. 2
the belt to the desired length to restrain a child seat or
Here are some simple steps you can take to minimize the
secure a large item in a seat
risk of harm from a deploying air bag:
Please pay close attention to the information in this
1. Children 12 years old and under should always ride
section. It tells you how to use your restraint system
buckled up in a rear seat.
properly, to keep you and your passengers as safe as
possible.
WARNING!
If you will be carrying children too small for adult-sized
Infants in rear facing child restraints should never
seat belts, the seat belts or the Lower Anchors and Tether
ride in the front seat of a vehicle with a passenger
for CHildren (LATCH) feature also can be used to hold
Advanced Front Air Bag. An air bag deployment can
infant and child restraint systems. For more information
cause severe injury or death to infants in that posi-
on LATCH, refer to Lower Anchors and Tether for
tion.
CHildren (LATCH).
Children that are not big enough to wear the vehicle seat 3. The driver and front passenger seats should be
belt properly (see section on Child Restraints) should be moved back as far as practical to allow the Advanced
secured in the rear seat in child restraints or belt- Front Air Bags room to inflate.
positioning booster seats. Older children who do not use
4. Do not lean against the door or window. If your
child restraints or belt-positioning booster seats should
vehicle has side air bags, and deployment occurs, the
ride properly buckled up in the rear seat. Never allow
side air bags will inflate forcefully into the space
children to slide the shoulder belt behind them or under
between you and the door.
their arm.
5. If the air bag system in this vehicle needs to be
If a child from 1 to 12 years old (not in a rear facing child
modified to accommodate a disabled person, contact
seat) must ride in the front passenger seat, move the seat
the Customer Center. Phone numbers are provided
as far back as possible and use the proper child restraint.
under If You Need Assistance.
(Refer to Child Restraints)
You should read the instructions provided with your
child restraint to make sure that you are using it properly.
2. All occupants should always wear their lap and
shoulder belts properly.
WARNING! WARNING! (Continued)

Relying on the air bags alone could lead to more Supplemental Side Air Bag Inflatable Curtain
severe injuries in a collision. The air bags work (SABIC) and Seat-Mounted Side Air Bags (SAB)
also need room to inflate. Do not lean against the 2
with your seat belt to restrain you properly. In
some collisions, the air bags wont deploy at all. door or window. Sit upright in the center of the
Always wear your seat belts even though you have seat.
air bags. In an accident, you and your passengers can suffer
Being too close to the steering wheel or instrument much greater injuries if you are not properly
panel during Advanced Front Air Bag deployment buckled up. You can strike the interior of your
could cause serious injury, including death. Air vehicle or other passengers, or you can be thrown
Bags need room to inflate. Sit back, comfortably out of the vehicle. Always be sure you and others
extending your arms to reach the steering wheel or in your vehicle are buckled up properly.
instrument panel.
Buckle up even though you are an excellent driver, even
(Continued) on short trips. Someone on the road may be a poor driver
and cause an accident that includes you. This can happen
far away from home or on your own street.
Research has shown that seat belts save lives, and they
WARNING!
can reduce the seriousness of injuries in an accident.
Some of the worst injuries happen when people are It is dangerous to ride in a cargo area, inside or
thrown from the vehicle. Seat belts reduce the possibility outside of a vehicle. In an accident, people riding
of ejection and the risk of injury caused by striking the in these areas are more likely to be seriously
inside of the vehicle. Everyone in a motor vehicle should injured or killed.
be belted at all times. Do not allow people to ride in any area of your
Lap/Shoulder Belts vehicle that is not equipped with seats and seat
All seats in your vehicle are equipped with lap/shoulder belts.
belts. Be sure everyone in your vehicle is in a seat and
using a seat belt properly.
The belt webbing in the retractor is designed to lock Wearing a seat belt incorrectly is dangerous. Seat
during very sudden stops or accidents. This feature belts are designed to go around the large bones of
allows the shoulder part of the belt to move freely with your body. These are the strongest parts of your
you under normal conditions. However, in an accident body and can take the forces of an accident the
the belt will lock and reduce the risk of you striking the best.
inside of the vehicle or being thrown out.
(Continued)
2. The seat belt latch plate is near the seatback of the
front seats and next to your arm in the rear seats. Grasp
Wearing your belt in the wrong place could make the latch plate and pull out the belt. Slide the latch plate
your injuries in an accident much worse. You up the webbing as far as necessary to allow the belt to go
might suffer internal injuries, or you could even 2
around your lap.
slide out of part of the belt. Follow these instruc-
tions to wear your seat belt safely and to keep your
passengers safe, too.
Two people should never be belted into a single
seat belt. People belted together can crash into one
another in an accident, hurting one another badly.
Never use a lap/shoulder belt or lap belt for more
than one person, no matter what their size.
Lap/Shoulder Belt Operating Instructions

1. Enter the vehicle and close the door. Sit back and
adjust the seat.
Pulling Out Belt and Latch Plate
3. When the belt is long enough to fit, insert the latch
WARNING!
plate into the buckle until you hear a click.
A belt that is worn under your arm is dangerous.
Your body could strike the inside surfaces of the
vehicle in an accident, increasing head and neck
injury. A belt worn under the arm can cause
internal injuries. Ribs arent as strong as shoulder
bones. Wear the belt over your shoulder so that
your strongest bones will take the force in a
collision.
A shoulder belt placed behind you will not protect
you from injury during an accident. You are more
likely to hit your head in a collision if you do not
wear your shoulder belt. The lap and shoulder belt
are meant to be used together. Inserting Latch Plate Into Buckle
WARNING!
A belt that is buckled into the wrong buckle will
not protect you properly. The lap portion could ride 2
too high on your body, possibly causing internal
injuries. Always buckle your belt into the buckle
nearest you.
A belt that is too loose will not protect you
properly. In a sudden stop you could move too far
forward, increasing the possibility of injury. Wear
your seat belt snugly.
4. Position the lap belt across your thighs, below your Removing Slack From Belt
abdomen. To remove slack in the lap belt portion, pull up
on the shoulder belt. To loosen the lap belt if it is too tight,
tilt the latch plate and pull on the lap belt. A snug belt
reduces the risk of sliding under the belt in an accident.
6. To release the belt, push the red button on the buckle.
WARNING!
The belt will automatically retract to its stowed position.
A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to
internal injury in an accident. The belt forces wont allow the belt to retract fully.
be at the strong hip and pelvic bones, but across your
abdomen. Always wear the lap belt as low as pos- WARNING!
sible and keep it snug. A frayed or torn belt could rip apart in an accident and
A twisted belt will not protect you properly. In a leave you with no protection. Inspect the belt system
collision, it could even cut into you. Be sure the belt periodically, checking for cuts, frays, or loose parts.
is straight. If you cant straighten a belt in your Damaged parts must be replaced immediately. Do not
vehicle, take it to your authorized dealer immedi- disassemble or modify the system. Seat belt assem-
ately and have it fixed. blies must be replaced after an accident if they have
been damaged (bent retractor, torn webbing, etc.).
5. Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. The retractor Third Row Center Shoulder Belt Instructions
will withdraw any slack in the belt. The shoulder belt for the third row center seat is located
in the headliner slightly behind the third row seat.
Pull the strap down and secure the small latch plate of
the lap belt into the small buckle until you hear a click.
Position the shoulder belt on your chest so that it is
comfortable and not resting on your neck. When the belt
is long enough to fit, insert the large latch plate into the
buckle until you hear a click. The retractor should 2
withdraw any slack in the belt.
To release the small latch plate, position the end of the
large latch plate against the red button on the small latch
plate and push upward. Reinstall the latch plates into the
headliner.
Adjustable Upper Shoulder Belt Anchorage
In the front seats and the second row outboard seats, the
shoulder belt anchorage can be adjusted upward or Adjustable Anchorage
downward to help position the belt away from your As a guide, if you are shorter than average you will
neck. The upper anchorage can be adjusted upward by prefer a lower position, and if you are taller than average
pushing anywhere on the anchorage. To move the an- you will prefer a higher position. When you release the
chorage downward, squeeze the actuation buttons while anchorage, try to move it up or down to make sure that
simultaneously pushing down on the anchorage assem- it is locked in position.
bly.
Seat Belts In Passenger Seating Positions If the passenger seating position is equipped with an
The seat belts in the passenger seating positions are ALR and is being used for normal usage:
equipped with an Automatic Locking Retractor (ALR) or
Only pull the belt webbing out far enough to comfortably
a cinching latch plate which are used to secure a child
wrap around the occupants mid-section so as to not
restraint system. For additional information refer to
activate the ALR. If the ALR is activated, you will hear a
Installing Child Restraints Using the Vehicle Seat Belt
ratcheting sound as the belt retracts. Allow the webbing
under the Child Restraint section. The chart below
to retract completely in this case and then carefully pull
defines the type of feature for each seating position.
out only the amount of webbing necessary to comfort-
Driver Center Passenger ably wrap around the occupants mid-section. Slide the
First Row N/A N/A ALR latch plate into the buckle until you hear a click.
Second Row ALR N/A ALR
Automatic Locking Retractor Mode (ALR) If
Third Row ALR Cinch ALR Equipped
N/A Not Applicable In this mode, the shoulder belt is automatically pre-
locked. The belt will still retract to remove any slack in
ALR Automatic Locking Retractor
the shoulder belt. The Automatic Locking Mode is avail-
able on all passenger-seating positions with a combina-
tion lap/shoulder belt. Use the Automatic Locking Mode
anytime a child safety seat is installed in a seating
position that has a belt with this feature. Children
WARNING!
12 years old and under should always be properly
restrained in the rear seat. The belt and retractor assembly must be replaced
if the seat belt assembly Automatic Locking Re- 2
How To Engage The Automatic Locking Mode
tractor (ALR) feature or any other seat belt func-
1. Buckle the combination lap and shoulder belt. tion is not working properly when checked ac-
cording to the procedures in the Service Manual.
2. Grasp the shoulder portion and pull downward until
the entire belt is extracted. Failure to replace the belt and retractor assembly
could increase the risk of injury in collisions.
3. Allow the belt to retract. As the belt retracts, you will
hear a clicking sound. This indicates the safety belt is Energy Management Feature
now in the Automatic Locking Mode. This vehicle has a safety belt system with an Energy
How To Disengage The Automatic Locking Mode Management feature in the front seating positions to help
Unbuckle the combination lap/shoulder belt and allow it further reduce the risk of injury in the event of a head-on
to retract completely to disengage the Automatic Locking accident. This safety belt system has a retractor assembly
Mode and activate the vehicle sensitive (emergency) that is designed to release webbing in a controlled
locking mode. manner. This feature is designed to help reduce the belt
force acting on the occupants chest.
Seat Belt Pretensioners Supplemental Active Head Restraints (AHR) If
The seat belts for both front seating positions are Equipped
equipped with pretensioning devices that are designed to These head restraints are passive, deployable compo-
remove slack from the seat belt in the event of an nents, and vehicles with this equipment cannot be readily
accident. These devices may improve the performance of identified by any markings, only through visual inspec-
the seat belt by assuring that the belt is tight about the tion of the head restraint. The head restraint will be split
occupant early in an accident. Pretensioners work for all in two halves, with the front half being soft foam and
size occupants, including those in child restraints. trim, the back half being decorative plastic.
NOTE: These devices are not a substitute for proper seat How The Active Head Restraints (AHR) Work
belt placement by the occupant. The seat belt still must be The Occupant Restraint Controller (ORC) determines
worn snugly and positioned properly. whether the severity, or type of rear impact will require
the Active Head Restraints (AHR) to deploy. If a rear
The pretensioners are triggered by the Occupant Re-
impact requires deployment, both the driver and front
straint Controller (ORC). Like the air bags, the preten-
passenger seat AHRs will be deployed.
sioners are single use items. A deployed pretensioner or
a deployed air bag must be replaced immediately.
When AHRs deploy during a rear impact, the front half
of the head restraint extends forward to minimize the gap
between the back of the occupants head and the AHR.
This system is designed to help prevent or reduce the 2
extent of injuries to the driver and front passenger in
certain types of rear impacts.
NOTE: The Active Head Restraints (AHR) may or may
not deploy in the event of a front or side impact.
However if during a front impact, a secondary rear
impact occurs, the AHR may deploy based on the sever-
ity and type of the impact.
Active Head Restraint (AHR) Components
1 Head Restraint Front Half 3 Head Restraint Back Half
(Soft Foam and Trim) (Decorative Plastic Rear Cover)
2 Seatback 4 Head Restraint Guide
Tubes
1. Grasp the deployed AHR from the rear seat.
CAUTION!
All occupants, including the driver, should not oper-
ate a vehicle or sit in a vehicles seat until the head
restraints are placed in their proper positions in order
to minimize the risk of neck injury in the event of an
accident.
NOTE: For more information on properly adjusting and

positioning the head restraint, refer to Adjusting Active
Head Restraints in Understanding The Features Of
Your Vehicle.
Resetting Active Head Restraints (AHR)
Hand Positioning Points On AHR
If the Active Head Restraints are triggered in an accident,
you must reset the head restraint on the drivers and 2. Position the hands on the top of the deployed AHR at
front passenger seat. You can recognize when the Active a comfortable position.
Head Restraint has been triggered by the fact that they 3. Pull down then rearward towards the rear of the
have moved forward (as shown in step three of the vehicle then down to engage the locking mechanism.
resetting procedure).
1 Downward Movement 3 Final Downward Movement To Engage Locking Mechanism

2 Rearward Movement
4. The AHR front soft foam and trim half should lock For safety reasons, have the Active Head Restraints
into the back decorative plastic half. checked by a qualified specialist at an authorized
dealer.
Enhanced Seat Belt Use Reminder System
(BeltAlert)
BeltAlert is a feature intended to remind the driver and
front passenger (if equipped with front passenger
BeltAlert) to fasten their seat belts. The feature is active
whenever the ignition is on. If the driver or front seat
passenger is unbelted, the Seat Belt Reminder Light will
turn on and remain on until both front seat belts are
fastened.
The BeltAlert warning sequence begins after the vehicle
AHR In Reset Position speed is over 5 mph (8 km/h), by blinking the Seat Belt
NOTE: Reminder Light and sounding an intermittent chime.
If you have difficulties or problems resetting the Once the sequence starts, it will continue for the entire
Active Head Restraints, see an authorized dealer. duration or until the respective seatbelts are fastened.
After the sequence completes, the Seat Belt Reminder
Light remains illuminated until the respective seat belts NOTE: Although BeltAlert has been deactivated, the
are fastened. The driver should instruct all other occu- Seat Belt Reminder Light will continue to illuminate
pants to fasten their seat belts. If a front seat belt is while the drivers or front passenger (if equipped with
unbuckled while traveling at speeds greater than 5 mph belt alert) seat belt remains unfastened. 2
(8 km/h), BeltAlert will provide both audio and visual
Seat Belt Lock Out
notification.
The center rear seat belt system has a lock out feature that
The front passenger seat BeltAlert is not active when the will not allow you to extract the center webbing unless
front passenger seat is unoccupied. BeltAlert may be the rear seat upper latch is engaged.
triggered when an animal or heavy object is on the front
Seat Belts And Pregnant Women
passenger seat or when the seat is folded flat (if
We recommend that pregnant women use the seat belts
equipped). It is recommended that pets be restrained in
throughout their pregnancies. Keeping the mother safe is
the rear seat in pet harnesses or pet carriers that are
the best way to keep the baby safe.
secured by seat belts, and cargo is properly stowed.
Pregnant women should wear the lap part of the belt
BeltAlert can be enabled or disabled by your authorized
across the thighs and as snug across the hips as possible.
dealer. Chrysler Group LLC does not recommend deac-
Keep the belt low so that it does not come across the
tivating BeltAlert.
abdomen. That way the strong bones of the hips will take
the force if there is an accident.
Seat Belt Extender Supplemental Restraint System (SRS) Air Bags
If a seat belt is too short, even when fully extended and This vehicle has Advanced Front Air Bags for both the
when the adjustable upper shoulder belt anchorage (if driver and front passenger as a supplement to the seat
equipped) is in its lowest position, your authorized belt restraint systems. The drivers Advanced Front Air
dealer can provide you with a seat belt extender. This Bag is mounted in the center of the steering wheel. The
extender should be used only if the existing belt is not passengers Advanced Front Air Bag is mounted in the
long enough. When it is not required, remove the ex- instrument panel, above the glove compartment. The
tender and store it. words SRS AIRBAG are embossed on the air bag covers.
In addition, the vehicle is equipped with a Supplemental
WARNING! Driver Side Knee Air Bag mounted in the instrument
panel below the steering column.
Using a seat belt extender when not needed can
increase the risk of injury in an accident. Only use
when the lap belt is not long enough when it is worn
low and snug, and in the recommended seating
positions. Remove and store the extender when not
needed.
The Advanced Front Air Bags have a multistage inflator
design. This allows the air bag to have different rates of
inflation based on the severity and type of collision.
This vehicle may be equipped with driver and/or front 2
passenger seat track position sensors that may adjust the
inflation rate of the Advanced Front Air Bags based upon
seat position.
This vehicle may be equipped with a driver and/or front
passenger seat belt buckle switch that detects whether
the driver or front passenger seat belt is fastened. The
seat belt buckle switch may adjust the inflation rate of the
Advanced Front Air Bag And Knee Bolster Locations Advanced Front Air Bags.
1 Driver And Passenger 2 Knee Bolster
Advanced Front Air Bags This vehicle is equipped with Supplemental Side Air Bag
3 Supplemental Driver Side Inflatable Curtains (SABIC) to protect the driver, front,
Knee Air Bag
and rear passengers sitting next to a window. The SABIC
NOTE: These air bags are certified to the new Federal air bags are located above the side windows and their
regulations for Advanced Air Bags. covers are also labeled: SRS AIRBAG.
This vehicle is equipped with Supplemental Seat- Steering Wheel and Column
Mounted Side Air Bags (SAB) to provide enhanced
Instrument Panel
protection for an occupant during a side impact. The
SABs are located in the outboard side of the front seats. Supplemental Driver Side Knee Air Bag
NOTE: Knee Impact Bolster
Air Bag covers may not be obvious in the interior trim,
Driver Advanced Front Air Bag
but they will open during air bag deployment.
Passenger Advanced Front Air Bag
After any accident, the vehicle should be taken to an
authorized dealer immediately. Supplemental Seat-Mounted Side Air Bags (SAB)
Air Bag System Components Supplemental Side Air Bag Inflatable Curtains
Your vehicle may be equipped with the following air bag (SABIC)
system components:
Front and Side Impact Sensors
Occupant Restraint Controller (ORC)
Front Seat Belt Pretensioners, Seat Belt Buckle Switch,
Air Bag Warning Light and Seat Track Position Sensors
Advanced Front Air Bag Features
WARNING!
The Advanced Front Air Bag system has multistage
driver and front passenger air bags. This system provides No objects should be placed over or near the air
output appropriate to the severity and type of collision as bag on the instrument panel, because any such
objects could cause harm if the vehicle is in a 2
determined by the Occupant Restraint Controller (ORC),
which may receive information from the front impact collision severe enough to cause the air bag to
sensors. inflate.
Do not put anything on or around the air bag
The first stage inflator is triggered immediately during an covers or attempt to open them manually. You may
impact that requires air bag deployment. This low output damage the air bags and you could be injured
is used in less severe collisions. A higher energy output is because the air bags may no longer be functional.
used for more severe collisions. The protective covers for the air bag cushions are
designed to open only when the air bags are
inflating.
Do not drill, cut or tamper with the knee bolster in
any way.
Do not mount any accessories to the knee bolster
such as alarm lights, stereos, citizen band radios,
etc.
Supplemental Seat-Mounted Side Air Bags (SAB) When the air bag deploys, it opens the seam between the
Supplemental Seat-Mounted Side Air Bags (SAB) may front and side of the seats trim cover. Each air bag
provide enhanced protection to help protect an occupant deploys independently; a left side impact deploys the left
during a side impact. The SAB is marked with an air bag air bag only and a right-side impact deploys the right air
label sewn into the outboard side of the front seats. bag only.
Supplemental Side Air Bag Inflatable Curtain
(SABIC)
SABIC air bags may offer side-impact and vehicle roll-
over protection to front and rear seat outboard occupants
in addition to that provided by the body structure. Each
air bag features inflated chambers placed adjacent to the
head of each outboard occupant that reduce the potential
for side-impact head injuries. The SABIC deploy down-
ward, covering both windows on the impact side.
NOTE:
Should a vehicle rollover occur, the pretensioners
Supplemental Seat-Mounted Side Air Bag Label and/or SAB and SABIC air bags on both sides of the
vehicle may deploy.
Air Bag covers may not be obvious in the interior trim,
but they will open during air bag deployment.
Do not use accessory seat covers or place objects
Being too close to the SAB and SABIC air bags during between you and the side air bags; the perfor-
deployment could cause you to be severely injured or mance could be adversely affected and/or objects 2
killed. could be pushed into you, causing serious injury.
The system includes side impact sensors that are cali-
brated to deploy the side air bags during impacts that Supplemental Driver Side Knee Air Bag
require air bag occupant protection. The Supplemental Driver Side Knee Air Bag provides
enhanced protection and works together with the Driver
WARNING! Advanced Front Air Bag during a frontal impact.
If your vehicle is equipped with left and right Knee Impact Bolster
Supplemental Side Air Bag Inflatable Curtain The Knee Impact Bolster helps protect the knees of the
(SABIC), do not stack luggage or other cargo up front passenger, and position the front occupant for the
high enough to block the location of the SABIC. best interaction with the Advanced Front Air Bag.
The area where the side curtain air bag is located
should remain free from any obstructions.
(Continued)
Along with seat belts and pretensioners, Advanced Front Advanced Front Air Bags and Supplemental Driver Side
Air Bags work with the Supplemental Driver Side Knee Knee Air Bag are designed to provide additional protec-
Air Bag and the passenger side knee bolster to provide tion by supplementing the seat belts in certain frontal
improved protection for the driver and front passenger. collisions depending on the severity and type of collision.
Side air bags also work with seat belts to improve Advanced Front Air Bags are not expected to reduce the
occupant protection. risk of injury in rear, side, or rollover collisions.
Air Bag Deployment Sensors And Controls The Advanced Front Air Bags and Supplemental Driver
Side Knee Air Bag will not deploy in all frontal collisions,
Occupant Restraint Controller (ORC)
including some that may produce substantial vehicle
The ORC is part of a Federally regulated safety system
damage for example, some pole collisions, truck
required for this vehicle.
underrides, and angle offset collisions. On the other
The ORC determines if deployment of the front and/or hand, depending on the type and location of impact,
side air bags in a frontal or side collision is required. Advanced Front Air Bags may deploy in crashes with
Based on the impact sensors signals, a central electronic little vehicle front-end damage but that produce a severe
ORC deploys the Advanced Front Air Bags, SABIC air initial deceleration.
bags, SABs, Supplemental Driver Side Knee Air Bag, and
The side air bags will not deploy in all side collisions.
front seat belt pretensioners, as required, depending on
Side air bag deployment will depend on the severity and
the severity and type of impact.
type of collision.
Because air bag sensors measure vehicle deceleration Also, the ORC turns on the Air Bag Warning
over time, vehicle speed and damage by themselves are Light in the instrument panel for approxi-
not good indicators of whether or not an air bag should mately four to eight seconds for a self-check
have deployed. when the ignition is first turned on. After the 2
self-check, the Air Bag Warning Light will turn off. If the
Seat belts are necessary for your protection in all acci-
ORC detects a malfunction in any part of the system, it
dents, and also are needed to help keep you in position,
turns on the Air Bag Warning Light, either momentarily
away from an inflating air bag.
or continuously. A single chime will sound if the light
The ORC monitors the readiness of the electronic parts of comes on again after initial startup.
the air bag system whenever the ignition switch is in the
It also includes diagnostics that will illuminate the instru-
START or ON/RUN position. If the key is in the OFF
ment cluster Air Bag Warning Light if a malfunction is
position, in the ACC position, or not in the ignition, the
noted that could affect the air bag system. The diagnos-
air bag system is not on and the air bags will not inflate.
tics also record the nature of the malfunction.
The ORC contains a backup power supply system that
may deploy the air bags even if the battery loses power or
it becomes disconnected prior to deployment.
are possible, based on the collision type and severity. The
WARNING!
steering wheel hub trim cover and the upper right side of
Ignoring the Air Bag Warning Light in your instru- the instrument panel separate and fold out of the way as
ment panel could mean you wont have the air bags the air bags inflate to their full size. The air bags fully
to protect you in a collision. If the light does not come inflate in about 50 to 70 milliseconds. This is about half of
on as a bulb check when the ignition is first turned the time it takes to blink your eyes. The air bags then
on, stays on after you start the vehicle, or if it comes quickly deflate while helping to restrain the driver and
on as you drive, have an authorized dealer service the front passenger.
air bag system immediately.
The Advanced Front Air Bag gas is vented through the
vent holes in the sides of the air bag. In this way, the air
Driver And Passenger Advanced Front Air Bag
bags do not interfere with your control of the vehicle.
Inflator Units
The Driver and Passenger Advanced Front Air Bag Supplemental Driver Side Knee Air Bag Inflator
Inflator Units are located in the center of the steering Unit
wheel and on the right side of the instrument panel. The Supplemental Driver Side Knee Air Bag unit is
When the ORC detects a collision requiring the Ad- located in the instrument panel trim beneath the steering
vanced Front Air Bags, it signals the inflator units. A large column. When the ORC detects a collision requiring the
quantity of non-toxic gas is generated to inflate the air bag, it signals the inflator units. A large quantity of
Advanced Front Air Bags. Different air bag inflation rates non-toxic gas is generated to inflate the Supplemental
Driver Side Knee Air Bag. The trim cover separates and in about 10 milliseconds. The side air bag moves at a very
folds out of the way allowing the air bag to inflate to the high speed and with such a high force that it could injure
full size. The air bag fully inflates in about 15 to 20 you if you are not seated properly, or if items are
milliseconds. The Supplemental Driver Side Knee Air positioned in the area where the side air bag inflates. This 2
Bag gas is vented through small vent holes in the side of especially applies to children.
the air bag.
Supplemental Side Air Bag Inflatable Curtain
Supplemental Seat-Mounted Side Air Bag (SAB) (SABIC) Inflator Units
Inflator Units During collisions where the impact is confined to a
The Supplemental Seat-Mounted Side Air Bags (SAB) are particular area of the side of the vehicle, the ORC may
designed to activate only in certain side collisions. deploy the SABIC air bags, depending on the severity
and type of collision. In these events, the ORC will
The ORC determines if a side collision requires the side
deploy the SABIC only on the impact side of the vehicle.
air bags to inflate, based on the severity and type of
collision. A quantity of non-toxic gas is generated to inflate the side
curtain air bag. The inflating side curtain air bag pushes
Based on the severity and type of collision, the side air
the outside edge of the headliner out of the way and
bag inflator on the crash side of the vehicle may be
covers the window. The air bag inflates in about 30
triggered, releasing a quantity of non-toxic gas. The
milliseconds (about one-quarter of the time that it takes
inflating SAB exits through the seat seam into the space
to blink your eyes) with enough force to injure you if you
between the occupant and the door. The SAB fully inflate
are not belted and seated properly, or if items are Enhanced Accident Response System
positioned in the area where the side curtain air bag In the event of an impact causing air bag deployment, if
inflates. This especially applies to children. The side the communication network remains intact, and the
curtain air bag is only about 3-1/2 in (9 cm) thick when power remains intact, depending on the nature of the
it is inflated. event the ORC will determine whether to have the
Enhanced Accident Response System perform the follow-
Because air bag sensors estimate deceleration over time,
ing functions:
vehicle speed and damage are not good indicators of
whether or not an air bag should have deployed. Cut off fuel to the engine.
NOTE: In a rollover the pretensioners and/or SAB and Flash hazard lights as long as the battery has power or
SABIC air bags may deploy on both sides of the vehicle. until the ignition key is turned off.
Front And Side Impact Sensors Turn on the interior lights, which remain on as long as
In front and side impacts, impact sensors can aid the the battery has power or until the ignition key is
ORC in determining appropriate response to impact removed.
events.
Unlock the doors automatically.
If A Deployment Occurs
The Advanced Front Air Bags are designed to deflate
immediately after deployment.
NOTE: Front and/or side air bags will not deploy in all bag inflation. These airborne particles may irritate the
collisions. This does not mean something is wrong with skin, eyes, nose, or throat. If you have skin or eye
the air bag system. irritation, rinse the area with cool water. For nose or
throat irritation, move to fresh air. If the irritation 2
If you do have a collision which deploys the air bags, any
continues, see your doctor. If these particles settle on
or all of the following may occur:
your clothing, follow the garment manufacturers in-
The nylon air bag material may sometimes cause structions for cleaning.
abrasions and/or skin reddening to the driver and
Do not drive your vehicle after the air bags have de-
front passenger as the air bags deploy and unfold. The
ployed. If you are involved in another collision, the air
abrasions are similar to friction rope burns or those
bags will not be in place to protect you.
you might get sliding along a carpet or gymnasium
floor. They are not caused by contact with chemicals.
WARNING!
They are not permanent and normally heal quickly.
However, if you havent healed significantly within a Deployed air bags and seat belt pretensioners can not
few days, or if you have any blistering, see your doctor protect you in another collision. Have the air bags,
immediately. seat belt pretensioners, and the front seat belt retrac-
tor assemblies replaced by an authorized dealer im-
As the air bags deflate, you may see some smoke-like
mediately. Also, have the Occupant Restraint Con-
particles. The particles are a normal by-product of the
troller (ORC) system serviced as well.
process that generates the non-toxic gas used for air
Maintaining Your Air Bag System
WARNING! Do not attempt to modify any part of your air bag
system. The air bag may inflate accidentally or
Modifications to any part of the air bag system may not function properly if modifications are
could cause it to fail when you need it. You could made. Take your vehicle to an authorized dealer
be injured if the air bag system is not there to for any air bag system service. If your seat includ-
protect you. Do not modify the components or ing your trim cover and cushion needs to be
wiring, including adding any kind of badges or serviced in any way (including removal or
stickers to the steering wheel hub trim cover or the loosening/tightening of seat attachment bolts),
upper right side of the instrument panel. Do not take the vehicle to your authorized dealer. Only
modify the front bumper, vehicle body structure, manufacturer approved seat accessories may be
or add aftermarket side steps or running boards. used. If it is necessary to modify the air bag system
It is dangerous to try to repair any part of the air for persons with disabilities, contact your autho-
bag system yourself. Be sure to tell anyone who rized dealer.
works on your vehicle that it has an air bag system.
(Continued)
Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine
You will want to have the air bags ready to related gauges are not working, the Occupant Restraint
inflate for your protection in a collision. The Controller (ORC) may also be disabled. The air bags may
Air Bag Warning Light monitors the internal not be ready to inflate for your protection. Promptly 2
circuits and interconnecting wiring associated check the fuse block for blown fuses. Refer to the label
with air bag system electrical components. While the air located on the inside of the fuse block cover for the
bag system is designed to be maintenance free. If any of proper air bag fuses. See your authorized dealer if the
the following occurs, have an authorized dealer service fuse is good.
the air bag system immediately. Event Data Recorder (EDR)
The Air Bag Warning Light does not come on for This vehicle is equipped with an event data recorder
approximately four to eight seconds when the ignition (EDR). The main purpose of an EDR is to record, in
switch is first turned to ON/RUN. certain crash or near crash-like situations, such as an air
bag deployment or hitting a road obstacle, data that will
The Air Bag Warning Light remains on after the
assist in understanding how a vehicles systems per-
approximate four to eight-second interval.
formed. The EDR is designed to record data related to
The Air Bag Warning Light comes on intermittently or vehicle dynamics and safety systems for a short period of
remains on while driving. time, typically 30 seconds or less. The EDR in this vehicle
is designed to record such data as:
How various systems in your vehicle were operating;
Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is
wer e buckled/fastened; required, and access to the vehicle or the EDR is needed.
In addition to the vehicle manufacturer, other parties,
How far (if at all) the driver was depressing the
such as law enforcement, that have the special equip-
accelerator and/or brake pedal; and,
ment, can read the information if they have access to the
How fast the vehicle was traveling. vehicle or the EDR.
These data can help provide a better understanding of Child Restraints
the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up all the
time, including babies and children. Every state in the
NOTE: EDR data are recorded by your vehicle only if a
United States and all Canadian provinces require that
non-trivial crash situation occurs; no data are recorded by
small children ride in proper restraint systems. This is the
the EDR under normal driving conditions and no per-
law, and you can be prosecuted for ignoring it.
sonal data (e.g., name, gender, age, and crash location)
are recorded. However, other parties, such as law en- Children 12 years or younger should ride properly
forcement, could combine the EDR data with the type of buckled up in a rear seat. According to crash statistics,
personally identifying data routinely acquired during a children are safer when properly restrained in the rear
crash investigation. seats rather than in the front.
The infant carrier is only used rearward-facing in the
WARNING!
vehicle. It is recommended for children from birth until
In a collision, an unrestrained child, even a tiny baby, they reach the weight or height limit of the infant carrier.
can become a projectile inside the vehicle. The force Convertible child seats can be used either rearward- 2
required to hold even an infant on your lap could facing or forward-facing in the vehicle. Convertible child
become so great that you could not hold the child, no seats often have a higher weight limit in the rearward-
matter how strong you are. The child and others facing direction than infant carriers do, so they can be
could be badly injured. Any child riding in your used rearward-facing by children who have outgrown
vehicle should be in a proper restraint for the childs their infant carrier but are still less than at least two years
size. old. Children should remain rearward-facing until they
reach the highest weight or height allowed by their
Infants And Child Restraints convertible child seat. Both types of child restraints are
Safety experts recommend that children ride rearward- held in the vehicle by the lap/shoulder belt or the
facing in the vehicle until they are two years old or until LATCH child restraint anchor system. Refer to Lower
they reach either the height or weight limit of their rear Anchors and Tether for CHildren (LATCH).
facing child safety seat. Two types of child restraints can
be used rearward-facing: infant carriers and convertible
child seats.
in the vehicle by the lap/shoulder belt or the LATCH
WARNING!
child restraint anchorage system. Refer to Lower An-
Rearward-facing child seats must never be used in chors and Tether for CHildren (LATCH).
the front seat of a vehicle with the front passenger air
All children whose weight or height is above the
bag unless the air bag is turned off. An air bag
forward-facing limit for the child seat should use a
deployment could cause severe injury or death to
belt-positioning booster seat until the vehicles seat belts
infants in this position.
fit properly. If the child cannot sit with knees bent over
the vehicles seat cushion while the childs back is against
Older Children And Child Restraints
the seatback, they should use a belt-positioning booster
Children who are two years old or who have outgrown
seat. The child and belt-positioning booster seat are held
their rear-facing convertible child seat can ride forward-
in the vehicle by the lap/shoulder belt.
facing in the vehicle. Forward-facing child seats and
convertible child seats used in the forward-facing direc- Children Too Large For Booster Seats
tion are for children who are over two years old or who Children who are large enough to wear the shoulder belt
have outgrown the rear-facing weight or height limit of comfortably, and whose legs are long enough to bend
their rear-facing convertible child seat. Children should over the front of the seat when their back is against the
remain in a forward-facing child seat with a harness for seatback, should use the lap/shoulder belt in a rear seat.
as long as possible, up to the highest weight or height
Make sure that the child is upright in the seat.
allowed by the child seat. These child seats are also held
The lap portion should be low on the hips and as snug
WARNING!
as possible.
Improper installation can lead to failure of an
Check belt fit periodically. A childs squirming or
infant or child restraint. It could come loose in a 2
slouching can move the belt out of position.
collision. The child could be badly injured or
If the shoulder belt contacts the face or neck, move the killed. Follow the manufacturers directions ex-
child closer to the center of the vehicle. If this doesnt actly when installing an infant or child restraint.
help, move the child to the center rear seating position A rearward-facing child restraint should only be
and use both the lap and shoulder belt. Never allow a used in a rear seat. A rearward-facing child re-
child to put the shoulder belt under an arm or behind straint in the front seat may be struck by a deploy-
their back. ing passenger air bag which may cause severe or
NOTE: For additional information, refer to fatal injury to the infant.
www.seatcheck.org or call 1866SEATCHECK. Cana-
dian residents should refer to Transport Canadas web- Here are some tips on getting the most out of your child
site for additional information: https://www.tc.gc.ca/ restraint:
roadsafety/safedrivers/childsafety/index.htm Before buying any restraint system, make sure that it
has a label certifying that it meets all applicable Safety
Standards. Chrysler Group LLC also recommends that
you make sure that you can install the child restraint in Installing The Child Restraint System
the vehicle where you will use it, before you buy it. We urge you to carefully follow the directions of the
manufacturer when installing your child restraint. Many,
The restraint must be appropriate for your childs
but not all, restraint systems will be equipped with
weight and height. Check the label on the restraint for
separate straps on each side, with each having a hook or
weight and height limits.
connector, and a means for adjusting the tension in the
Carefully follow the instructions that come with the strap. Forward-facing toddler restraints and some
restraint. If you install the restraint improperly, it may rearward-facing infant restraints will also be equipped
not work when you need it. with a tether strap, a hook and means for adjusting the
tension in the strap. Not all child restraint systems will be
Buckle the child into the seat according to the child
installed as described here. Again, carefully follow the
restraint manufacturers directions.
installation instructions that are provided with the child
restraint system.
WARNING!
In general, you will first loosen the child seat adjusters on
When your child restraint is not in use, secure it in
the lower straps and tether straps so that you can more
the vehicle with the seat belt or remove it from the
easily attach the hook or connector to the lower anchor-
vehicle. Do not leave it loose in the vehicle. In a
ages and tether anchorages. Then tighten all three straps
sudden stop or accident, it could strike the occupants
as you push the child restraint rearward and downward
or seatbacks and cause serious personal injury.
into the seat.
Not all child restraint systems will be installed as we row fold-in-floor seats. Second-row seats also feature
have described here. Again, carefully follow the instruc- tether strap anchorages, located in the rear surface of the
tions that come with the child restraint system. seatback. In addition, all third row fold-in-floor seats are
equipped with a child restraint tether anchor at the center 2
WARNING! seating position.
Improper installation of a child restraint to the NOTE:
LATCH anchorages can lead to failure of an infant or When using the LATCH attaching system to install a
child restraint. The child could be badly injured or child restraint, please ensure that all seat belts not
killed. Follow the manufacturers directions exactly being used for occupant restraints are stowed and out
when installing an infant or child restraint. of reach of children. It is recommended that before
installing the child restraint, buckle the seat belt so the
Installing The LATCH-Compatible Child Restraint seat belt is tucked behind the child restraint and out of
System reach. If the buckled seat belt interferes with the child
Each vehicle, except commercial cargo vehicles, restraint installation, instead of tucking the seat belt
is equipped with the child restraint anchorage behind the child restraint, route the seat belt through
system called LATCH, which stands for Lower the child restraint belt path and then buckle it. This
Anchors and Tether for CHildren. Two LATCH should stow the seat belt out of the reach of an
child restraint anchorage systems are installed on all inquisitive child. Remind all children in the vehicle
second-row seats and in the center position on all third
that the seat belts are not toys and should not be
played with, and never leave your child unattended in
the vehicle.
If your child restraint seat is not LATCH-compatible,
install the restraint using the vehicle seat belts.
Installing the Lower Attachments:
1. The vehicle lower anchorages are round bars located
at the rear of the seat cushion where it meets the seatback.
LATCH Anchorages (Second Row Anchorages Shown)

NOTE: It is recommended to loosen the top tether strap
and route it loosely prior to securing the lower anchors so
the top tether strap is not trapped between the vehicle
seat and child restraint. 2
3. Attach the lower child restraint attachment straps to
the vehicles lower anchor bars. Ensure that the lower
attachment strap is firmly engaged and that the hook is
secure.
4. Tighten the lower attachment strap while firmly push-
ing the child restraint rearward and downward into the
vehicle seat. Remove all slack in the lower attachment
LATCH Anchorages straps. Reference the child restraint instructions for infor-
(Third Row 60/40 Anchorages Shown) mation on properly removing slack.
2. Loosen the adjusters on the lower child restraint
attachment straps (reference the child restraint seat in-
structions) to ease the installation.
Installing the Top Tether Strap
(with either Lower Anchors or Vehicle Seat Belt):
1. Route the top tether strap under the adjustable head
restraint between the steel posts.
2. Provide enough slack (reference child restraint in-
structions) for the tether strap to reach the tether anchor
located near the bottom of the seat back.
3. Clip tether hook to tether anchor. Ensure that the hook
is firmly engaged and secure.
4. Remove all slack and tighten tether strap according to
child restraint manufacturers instructions. Rear Seat Tether Strap Mounting
(Second Row Anchorage Shown)
NOTE: The top tether strap is always to be secured,
regardless of if the child restraint is installed with the
lower anchors or the vehicle seat belt.
WARNING!
An incorrectly anchored tether strap could lead to
increased head motion and possible injury to the 2
child. Use only the anchor positions directly behind
the child seat to secure a child restraint top tether
strap.
Installing The Child Restraint Using The Vehicle

Seat Belts
The seat belts in the passenger seating positions are
equipped with an Automatic Locking Retractor (ALR) or
LATCH Anchorages a cinching latch plate to secure a Child Restraint System
(Third Row 60/40 Anchorage Shown) (CRS). These types of seat belts are designed to keep the
lap portion of the seat belt tight around the child restraint
so that it is not necessary to use a locking clip. The ALR
will make a ratcheting noise if you extract the entire belt
from the retractor and then allow the belt to retract into
the retractor. For additional information on ALR, refer to
Automatic Locking Mode description under Seat then allow the belt to retract into the retractor. As the belt
Belts in Passenger Seating Positions section. The chart retracts, you will hear a ratcheting sound. This indicates
below defines the seating positions with an Automatic the safety belt is now in the Automatic Locking mode.
Locking Retractor (ALR) or a cinching latch plate.
2. Finally, pull on any excess webbing to tighten the lap
Driver Center Passenger portion around the child restraint. Any seat belt system
CRS Lock CRS Lock CRS Lock will loosen with time, so check the belt occasionally, and
First Row N/A N/A ALR pull it tight if necessary.
Second Row ALR N/A ALR Installing a Child Restraint with a Cinching Latch Plate:
Third Row ALR Cinch ALR
1. To install a child restraint with a cinching latch plate,
N/A Not Applicable first, pull enough of the seat belt webbing from the
ALR Automatic Locking Retractor retractor to route it through the belt path of the child
restraint. Slide the latch plate into the buckle until you
Installing a Child Restraint with an ALR: hear a click.
1. To install a child restraint with ALR, first, pull enough 2. Finally, pull on any excess webbing to tighten the lap
of the seat belt webbing from the retractor to route it portion around the child restraint. Any seat belt system
through the belt path of the child restraint. Slide the latch will loosen with time, so check the belt occasionally, and
plate into the buckle until you hear a click. Next, pull it tight if necessary.
extract all the seat belt webbing out of the retractor and
Transporting Pets
WARNING!
Air Bags deploying in the front seat could harm your pet.
An unrestrained pet could be thrown about and possibly NEVER carry a child in a rear facing infant carrier in
injured, or injure a passenger during panic braking or in a vehicle without rear seats. In an accident, serious 2
an accident. injury or death may occur from the deploying pas-
senger airbag.
Pets should be restrained in the rear seat in pet harnesses
or pet carriers that are secured by seat belts.
COMMERCIAL CARGO VEHICLES (NO FACTORY

INSTALLED REAR SEATS) IF EQUIPPED
Commercial cargo vehicles are not designed for use as a
family vehicle and are not intended for carrying children
in the front passenger seat. However, if you must carry a
child in a vehicle without a rear seat, the passenger seat
should be moved to the full rearward position and the
child must be in a proper restraint system based on its
age, size and weight.
Commercial Child Restraint Tether Anchor

This vehicle is equipped with a child restraint tether Restraining Infants And Small Children In
anchor located on the lower rear of the front passenger Commercial Cargo Vehicles
seat. Use this tether anchor to secure only forward- There are different sizes and types of restraints for
facing child restraints equipped with an upper tether children from newborn size to the child almost large
strap. enough for an adult safety belt. Use the restraint that is
correct for your child:
WARNING!
The forward-facing child seat is for children from
Rearward-facing infant restraints must never be se- about 20 to 40 lbs (9 to 18 kg), and more than one year
cured in the passenger seat of a vehicle with a old.
passenger airbag. In an accident, a passenger airbag
A convertible child seat, one that is designed to be
may deploy causing severe injury or death to infants
used for children who are too heavy for a rearward-
riding in rearward-facing infant restraints.
facing infant seat, may be used IN THE FORWARD
FACING POSITION ONLY, IT MUST NEVER BE
INSTALLED FACING TO THE REAR IN A COMMER-
CIAL CARGO VEHICLE. When a convertible seat is
properly installed facing forward, the vehicle seat
should be adjusted to the rear most position.
Children more than 40 lbs (18 kg) should be secured in 3. Route the tether strap under the head rest.
the passenger seat in a child restraint or belt-
NOTE: Ensure that the child restraint tether strap is
positioning booster seat with the seat adjusted to the
centered between the headrest supports underneath the
rear most position. Older children who do not use 2
head rest.
child restraints or belt-positioning booster seats
should ride properly buckled in the passenger seat 4. Using the hook attached to the child restraint tether
with the seat adjusted to the rearmost position. Never strap, attach the child restraint tether strap to the metal
allow children to slide the shoulder belt behind them anchor on the lower rear of the front passenger seat.
or under their arm.
5. Following the child seat manufacturers instructions,
Tether Installation For Commercial Cargo Vehicles tighten the child restraint tether strap.
To secure the child restraint upper tether strap to the
6. Inspect the tether anchor strap for nicks, abrasions,
vehicle, follow the instructions shown:
discoloration, and loose threads. If these, or any other
1. Locate the child restraint tether anchor on the lower condition that might affect the performance of the strap is
rear of the front passenger seat. observed, DO NOT USE. Contact your authorized deal-
ership for a replacement part.
2. Follow the child restraint manufacturers directions
for proper use of connecting the child restraint to the
extended tether strap.
While cruising, brief full-throttle acceleration within the
WARNING!
limits of local traffic laws contributes to a good break-in.
The vehicle tether anchor is designed to be used with Wide-open throttle acceleration in low gear can be detri-
a child restraint only. It should not be used for any mental and should be avoided.
other purpose. Before use, inspect the tether anchor
The engine oil installed in the engine at the factory is a
strap for nicks, abrasions, discoloration, and loose
high-quality energy conserving type lubricant. Oil
threads. If these or any other condition that might
changes should be consistent with anticipated climate
affect the performance of the strap is observed, DO
conditions under which vehicle operations will occur. For
NOT USE that strap. Personal injury may result.
the recommended viscosity and quality grades, refer to
Contact your authorized dealership for a replacement
Maintenance Procedures in Maintaining Your Ve-
part.
hicle.
ENGINE BREAK-IN RECOMMENDATIONS CAUTION!

A long break-in period is not required for the engine and
drivetrain (transmission and axle) in your vehicle. Never use Non-Detergent Oil or Straight Mineral Oil
in the engine or damage may result.
Drive moderately during the first 300 miles (500 km).
After the initial 60 miles (100 km), speeds up to 50 or NOTE: A new engine may consume some oil during its
55 mph (80 or 90 km/h) are desirable. first few thousand miles (kilometers) of operation. This
should be considered a normal part of the break-in and
not interpreted as an indication of difficulty.
Do not allow people to ride in any area of your
SAFETY TIPS vehicle that is not equipped with seats and seat
belts. 2
Transporting Passengers
Be sure everyone in your vehicle is in a seat and
NEVER TRANSPORT PASSENGERS IN THE CARGO
using a seat belt properly.
AREA.
Exhaust Gas
WARNING!
Do not leave children or animals inside parked WARNING!
vehicles in hot weather. Interior heat build-up may
Exhaust gases can injure or kill. They contain carbon
cause serious injury or death.
monoxide (CO), which is colorless and odorless.
It is extremely dangerous to ride in a cargo area,
Breathing it can make you unconscious and can
inside or outside of a vehicle. In a collision, people
eventually poison you. To avoid breathing (CO),
riding in these areas are more likely to be seri-
follow these safety tips:
ously injured or killed.
(Continued)
(Continued)
Whenever a change is noticed in the sound of the exhaust
system, when exhaust fumes can be detected inside the
Do not run the engine in a closed garage or in vehicle, or when the underside or rear of the vehicle is
confined areas any longer than needed to move damaged, have a competent mechanic inspect the com-
your vehicle in or out of the area. plete exhaust system and adjacent body areas for broken,
If you are required to drive with the trunk/liftgate damaged, deteriorated, or mispositioned parts. Open
open, make sure that all windows are closed and seams or loose connections could permit exhaust fumes
the climate control BLOWER switch is set at high to seep into the passenger compartment. In addition,
speed. DO NOT use the recirculation mode. inspect the exhaust system each time the vehicle is raised
If it is necessary to sit in a parked vehicle with the for lubrication or oil change. Replace as required.
engine running, adjust your heating or cooling
controls to force outside air into the vehicle. Set Safety Checks You Should Make Inside The
the blower at high speed. Vehicle
Seat Belts
The best protection against carbon monoxide entry into Inspect the belt system periodically, checking for cuts,
the vehicle body is a properly maintained engine exhaust frays, and loose parts. Damaged parts must be replaced
system. immediately. Do not disassemble or modify the system.
Front seat belt assemblies must be replaced after a Defroster
collision. Rear seat belt assemblies must be replaced after Check operation by selecting the defrost mode and place
a collision if they have been damaged (i.e., bent retractor, the blower control on high speed. You should be able to
torn webbing, etc.). If there is any question regarding belt feel the air directed against the windshield. See your 2
or retractor condition, replace the belt. authorized dealer for service if your defroster is
inoperable.
Air Bag Warning Light
The light should come on and remain on for four to eight Floor Mat Safety Information
seconds as a bulb check when the ignition switch is first Always use floor mats designed to fit the footwell of your
turned ON. If the light is not lit during starting, see your vehicle. Use only floor mats that leave the pedal area
authorized dealer. If the light stays on, flickers, or comes unobstructed and that are firmly secured so that they
on while driving, have the system checked by an autho- cannot slip out of position and interfere with the pedals
rized dealer. or impair safe operation of your vehicle in other ways.

Pedals that cannot move freely can cause loss of Check mounting of mats on a regular basis. Al-
vehicle control and increase the risk of serious per- ways properly reinstall and secure floor mats that
sonal injury. have been removed for cleaning.
Always make sure that floor mats are properly Always make sure that objects cannot fall into the
attached to the floor mat fasteners. driver footwell while the vehicle is moving. Ob-
Never place or install floor mats or other floor jects can become trapped under the brake pedal
coverings in the vehicle that cannot be properly and accelerator pedal causing a loss of vehicle
secured to prevent them from moving and inter- control.
fering with the pedals or the ability to control the If required, mounting posts must be properly
vehicle. installed, if not equipped from the factory.
Never put floor mats or other floor coverings on Failure to properly follow floor mat installation or
top of already installed floor mats. Additional mounting can cause interference with the brake
floor mats and other coverings will reduce the size pedal and accelerator pedal operation causing loss
of the pedal area and interfere with the pedals. of control of the vehicle.
(Continued)
Periodic Safety Checks You Should Make Outside Door Latches
The Vehicle Check for positive closing, latching, and locking.
Tires Fluid Leaks
Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, 2
patterns. Check for stones, nails, glass, or other objects engine coolant, oil, or other fluid leaks. Also, if gasoline
lodged in the tread or sidewall. Inspect the tread for cuts fumes are detected or if fuel, power steering fluid, or
and cracks. Inspect sidewalls for cuts, cracks and bulges. brake fluid leaks are suspected, the cause should be
Check the wheel nuts for tightness. Check the tires located and corrected immediately.
(including spare) for proper cold inflation pressure.
Lights
Have someone observe the operation of exterior lights
while you work the controls. Check turn signal and high
beam indicator lights on the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE
CONTENTS
3
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Tilt Mirrors In Reverse (Available With
Memory Seat Only) If Equipped . . . . . . . . 116
Inside Day/Night Mirror If Equipped . . . 112
Power Folding Mirrors If Equipped . . . . . 116
Automatic Dimming Mirror If Equipped . . 113
Illuminated Vanity Mirrors If Equipped . . 117
Outside Mirrors . . . . . . . . . . . . . . . . . . . . . 113
Blind Spot Monitoring If Equipped . . . . . . . 117
Drivers Automatic Dimming Mirror If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Rear Cross Path . . . . . . . . . . . . . . . . . . . . . 123
Outside Mirror Folding Feature . . . . . . . . . . 114 Modes Of Operation . . . . . . . . . . . . . . . . . . 124
Power Mirrors If Equipped . . . . . . . . . . . 114 Uconnect Phone If Equipped . . . . . . . . . . 125
Heated Mirrors If Equipped . . . . . . . . . . . 115 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 128
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Phone Call Features . . . . . . . . . . . . . . . . . . 135 Heated Seats If Equipped . . . . . . . . . . . . 163
Uconnect Phone Features . . . . . . . . . . . . . 138 Manual Front/Second Row Seat Adjuster . . . 166
Advanced Phone Connectivity . . . . . . . . . . . 143 Manual Reclining Seats If Equipped . . . . . 167
Things You Should Know About Your Head Restraints . . . . . . . . . . . . . . . . . . . . . 168
Uconnect Phone . . . . . . . . . . . . . . . . . . . . 144
Stow n Go Seating If Equipped . . . . . . . 172
General Information . . . . . . . . . . . . . . . . . . 155
Quad Seats If Equipped . . . . . . . . . . . . . 178
Voice Command If Equipped . . . . . . . . . . . 155
Second Row Bench Seat If Equipped . . . . 184
Voice Command System Operation . . . . . . . . 155
Third Row Power Recline If Equipped . . . 186
Commands . . . . . . . . . . . . . . . . . . . . . . . . 156
Third Row Power Folding Seat If
Voice Training . . . . . . . . . . . . . . . . . . . . . . 160 Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 186
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Manually Folding Third Row Seats If
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 188
Power Seats If Equipped . . . . . . . . . . . . . 160
Plastic Grocery Bag Retainer Hooks . . . . . . . 191
Power Lumbar If Equipped . . . . . . . . . . . 162
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107
Driver Memory Seat If Equipped . . . . . . . . 191 Dimmer Controls . . . . . . . . . . . . . . . . . . . . 201
Setting Memory Positions And Linking RKE Multifunction Lever . . . . . . . . . . . . . . . . . . 203
Transmitter To Memory . . . . . . . . . . . . . . . . 192
Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . 204
Easy Entry/Exit Seat (Available With
Lane Change Assist . . . . . . . . . . . . . . . . . . . 204
Memory Seat Only) . . . . . . . . . . . . . . . . . . . 195 3
High/Low Beam Switch . . . . . . . . . . . . . . . 204
To Open And Close The Hood . . . . . . . . . . . . 196
Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . 204
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 198
Battery Protection . . . . . . . . . . . . . . . . . . . . 205
Headlight Switch . . . . . . . . . . . . . . . . . . . . 198
Windshield Wiper And Washers . . . . . . . . . . . 205
Automatic Headlights If Equipped . . . . . . 199
Intermittent Wiper System . . . . . . . . . . . . . . 206
Headlights On With Wipers If Equipped . . 199
Windshield Wiper Operation . . . . . . . . . . . . 206
Headlight Delay If Equipped . . . . . . . . . . 199
Windshield Washers . . . . . . . . . . . . . . . . . . 206
Lights-On Reminder . . . . . . . . . . . . . . . . . . 200
Mist Feature . . . . . . . . . . . . . . . . . . . . . . . . 207
Daytime Running Lights If Equipped . . . . 200
Rear Wiper And Washer . . . . . . . . . . . . . . . 207
Front Fog Lights If Equipped . . . . . . . . . . 201
Rain Sensing Wipers If Equipped . . . . . . . 207 Parksense Warning Display . . . . . . . . . . . . 216
Tilt/Telescoping Steering Column . . . . . . . . . . 209 Parksense Display . . . . . . . . . . . . . . . . . . . 217
Heated Steering Wheel If Equipped . . . . . . 210 Enabling/Disabling Parksense . . . . . . . . . . 220
Adjustable Pedals If Equipped . . . . . . . . . . 211 Service The Parksense Rear Park Assist
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 221
Electronic Speed Control If Equipped . . . . . 212
Cleaning The Parksense System . . . . . . . . . 221
To Activate . . . . . . . . . . . . . . . . . . . . . . . . . 213
Parksense System Usage Precautions . . . . . . 221
To Set A Desired Speed . . . . . . . . . . . . . . . . 214
Parkview Rear Back Up Camera If
To Deactivate . . . . . . . . . . . . . . . . . . . . . . . 214
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
To Resume Speed . . . . . . . . . . . . . . . . . . . . 214
Turning Parkview On Or Off With
To Vary The Speed Setting . . . . . . . . . . . . . . 214 Navigation/Multimedia Radio . . . . . . . . . . . 226
To Accelerate For Passing . . . . . . . . . . . . . . 215 Turning Parkview On Or Off Without
Navigation/Multimedia Radio . . . . . . . . . . . 227
Parksense Rear Park Assist If Equipped . . . 215
Parksense Sensors . . . . . . . . . . . . . . . . . . . 216
Overhead Consoles . . . . . . . . . . . . . . . . . . . . 227 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . 239
Front Overhead Console . . . . . . . . . . . . . . . 227 Troubleshooting Tips . . . . . . . . . . . . . . . . . . 239
Courtesy/Interior Lighting . . . . . . . . . . . . . 228 General Information . . . . . . . . . . . . . . . . . . 240
Sunglass Storage (Non-Sunroof Only) . . . . . . 228 Power Sunroof If Equipped . . . . . . . . . . . . 241
3
Rear Courtesy/Reading Lights If Opening Sunroof Express . . . . . . . . . . . . 242
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . 230
Opening The Sunroof Manual Mode . . . . . 242
Rear Overhead Consoles If Equipped . . . . 230
Closing Sunroof Express . . . . . . . . . . . . . 242
Garage Door Opener If Equipped . . . . . . . . 231
Closing Sunroof Manual Mode . . . . . . . . 242
Before You Begin Programming
Pinch Protect Feature . . . . . . . . . . . . . . . . . 242
HomeLink . . . . . . . . . . . . . . . . . . . . . . . . 233
Pinch Protect Override . . . . . . . . . . . . . . . . 243
Programming A Rolling Code . . . . . . . . . . . 234
Venting Sunroof Express . . . . . . . . . . . . . 243
Programming A Non-Rolling Code . . . . . . . . 236
Sunshade Operation . . . . . . . . . . . . . . . . . . 243
Canadian/Gate Operator Programming . . . . 237
Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . 243
Using HomeLink . . . . . . . . . . . . . . . . . . . 238
Sunroof Maintenance . . . . . . . . . . . . . . . . . 244 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Ignition Off Operation . . . . . . . . . . . . . . . . . 244 Glove Compartments . . . . . . . . . . . . . . . . . 254
Sunroof Fully Closed . . . . . . . . . . . . . . . . . . 244 Door Trim Panel Storage . . . . . . . . . . . . . . . 255
Electrical Power Outlets If Equipped . . . . . . 244 Driver Seatback Storage If Equipped . . . . 256
Power Inverter If Equipped . . . . . . . . . . . . 249 Umbrella Holder . . . . . . . . . . . . . . . . . . . . . 256
Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . . 250 Second Row Seat Storage Bins
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 257
Instrument Panel Cupholders . . . . . . . . . . . . 250
Storage Bin Safety Warning . . . . . . . . . . . . . 258
Super Console If Equipped . . . . . . . . . . . 251
Coat Hooks . . . . . . . . . . . . . . . . . . . . . . . . 260
Premium Console Cupholders
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 252 Cargo Area Storage . . . . . . . . . . . . . . . . . . . 260
Interior Bottle Holders . . . . . . . . . . . . . . . . 252 Console Features . . . . . . . . . . . . . . . . . . . . . . 261
Smokers Package Kit If Equipped . . . . . . 253 Basic Console . . . . . . . . . . . . . . . . . . . . . . . 261
Premium Console If Equipped . . . . . . . . . 262
Super Console If Equipped . . . . . . . . . . . 266 Rear Load-Leveling System If Equipped . . . 270
Cargo Area Features . . . . . . . . . . . . . . . . . . . 268 Roof Luggage Rack If Equipped . . . . . . . . . 270
Rechargeable Flashlight . . . . . . . . . . . . . . . . 268 Deploying The Crossbars . . . . . . . . . . . . . . . 272
Rear Window Features . . . . . . . . . . . . . . . . . . 269 Sun Screens If Equipped . . . . . . . . . . . . . . 277
3
Rear Window Defroster . . . . . . . . . . . . . . . . 269
MIRRORS
Inside Day/Night Mirror If Equipped
A two-point pivot system allows for horizontal and
vertical adjustment of the mirror. Adjust the mirror to
center on the view through the rear window.
Headlight glare can be reduced by moving the small
control under the mirror to the night position (toward the
rear of the vehicle). The mirror should be adjusted while
set in the day position (toward the windshield).
Manual Rearview Mirror

Automatic Dimming Mirror If Equipped
CAUTION!
This mirror automatically adjusts for headlight glare
from vehicles behind you. You can turn the feature on or To avoid damage to the mirror during cleaning, never
off by pressing the button at the base of the mirror. A light spray any cleaning solution directly onto the mirror.
to the left of the button will illuminate to indicate when Apply the solution onto a clean cloth and wipe the
the dimming feature is activated. The sensor to the right mirror clean. 3
of the button does not illuminate.
Outside Mirrors
To receive maximum benefit, adjust the outside mirror(s)
to center on the adjacent lane of traffic with a slight
overlap of the view obtained on the inside mirror.
Automatic Dimming Mirror

Outside Mirror Folding Feature
WARNING!
All outside mirrors are hinged and may be moved either
Vehicles and other objects seen in an outside convex forward or rearward to resist damage. The hinges have
mirror will look smaller and farther away than they three detent positions: full forward, full rearward and
really are. Relying too much on side convex mirrors normal.
could cause you to collide with another vehicle or
Power Mirrors If Equipped
other object. Use your inside mirror when judging
The power mirror controls are located on the driver-side
the size or distance of a vehicle seen in a side convex
door trim panel.
mirror.
Drivers Automatic Dimming Mirror If Equipped

The drivers outside mirror will automatically adjust for
glare from vehicles behind you. This feature is controlled
by the inside automatic dimming mirror and can be
turned on or off by pressing the button at the base of the
inside mirror. The mirror will automatically adjust for
headlight glare when the inside mirror adjusts.
NOTE: A light in the selected button will illuminate
indicating the mirror is activated and can be adjusted.
Using the mirror control switch, press on any of the four
arrows for the direction that you want the mirror to
move.
3
Drivers side power mirror preselected positions can be
controlled by the optional Driver Memory Seat Feature.
Refer to Driver Memory Seat in Understanding The
Features Of Your Vehicle for further information.
Heated Mirrors If Equipped
Power Mirror Controls These mirrors are heated to melt frost or ice. This
feature is activated whenever you turn on the rear
The power mirror controls consist of mirror select but-
window defroster. Refer to Rear Window Features in
tons and a four-way mirror control switch. To adjust a
Understanding The Features Of Your Vehicle for fur-
mirror, press either the L (left) or R (right) to select the
ther information.
mirror that you want to adjust.
Tilt Mirrors In Reverse (Available With Memory Power Folding Mirrors If Equipped
Seat Only) If Equipped The switch for the power folding mirrors is located
Tilt Mirrors in Reverse provides automatic outside mirror between the power mirror switches L (left) and R (right).
positioning which will aid the drivers view of the ground Press the switch once and the mirrors will fold in,
rearward of the front doors. The drivers outside mirror pressing the switch a second time will return the mirrors
will move slightly downward from the present position to the normal driving position.
when the vehicle is shifted into REVERSE. The drivers
NOTE: Pressing the power folding mirror switch for
outside mirror will then return to the original position
more than four seconds, or if the vehicle speed is greater
when the vehicle is shifted out of REVERSE position.
than 5 mph (8 km/h) will disable the folding feature.
Each stored memory setting will have an associated Tilt
Mirrors in Reverse position. If the mirrors are in the folded position, and vehicle
speed is equal or greater than 5 mph (8 km/h), they will
NOTE: The Tilt Mirrors in Reverse feature is not en-
automatically unfold.
abled when delivered from the factory. The Tilt Mirrors in
Reverse feature can be enabled or disabled in the Elec-
tronic Vehicle Information Center (EVIC). Refer to Elec-
tronic Vehicle Information Center (EVIC)/Customer-
Programmable Features in Understanding Your
Instrument Panel for further information.
Illuminated Vanity Mirrors If Equipped BLIND SPOT MONITORING IF EQUIPPED
An illuminated vanity mirror is located on the sun visor. The Blind Spot Monitoring (BSM) system uses two radar-
To use the mirror, rotate the sun visor down and swing based sensors, located inside the rear bumper fascia, to
the mirror cover upward. The lights turn on automati- detect highway licensable vehicles (automobiles, trucks,
cally. Closing the mirror cover turns off the lights. motorcycles, etc.) that enter the blind spot zones from the
rear/front/side of the vehicle. 3
Illuminated Mirror
Rear Detection Zones
When the vehicle is started, the BSM warning light will The BSM system detection zone DOES NOT change if
momentarily illuminate in both outside rear view mirrors your vehicle is towing a trailer. Therefore, visually
to let the driver know that the system is operational. The verify the adjacent lane is clear for both your vehicle
BSM system sensors operate when the vehicle is in any and trailer before making a lane change. If the trailer
forward gear or REVERSE and enters stand-by mode or other object (i.e., bicycle, sports equipment) extends
when the vehicle is in PARK. beyond the side of your vehicle, this may result in the
BSM warning light remaining illuminated the entire
The BSM detection zone covers approximately one lane
time the vehicle is in a forward gear.
on both sides of the vehicle (11 ft or 3.35 m). The zone
starts at the outside rear view mirror and extends ap- The area on the rear fascia where the radar sensors are
proximately 20 ft (6 m) to the rear of the vehicle. The BSM located must remain free of snow, ice, and dirt/road
system monitors the detection zones on both sides of the contamination so that the BSM system can function
vehicle when the vehicle speed reaches approximately properly. Do not block the area of the rear fascia where
6 mph (10 km/h) or higher and will alert the driver of the radar sensors are located with foreign objects (bum-
vehicles in these areas. per stickers, bicycle racks, etc.).
NOTE:
The BSM system does NOT alert the driver about
rapidly approaching vehicles that are outside the
detection zones.
Sensor Locations BSM Warning Light

The BSM system notifies the driver of objects in the The BSM system monitors the detection zone from three
detection zones by illuminating the BSM warning light different entry points (side, rear, front) while driving to
located in the outside mirrors in addition to sounding an see if an alert is necessary. The BSM system will issue an
audible (chime) alert and reducing the radio volume. alert during these types of zone entries.
Refer to Modes Of Operation for further information.
Entering From The Side Entering From The Rear
Vehicles that move into your adjacent lanes from either Vehicles that come up from behind your vehicle on either
side of the vehicle. side and enter the rear detection zone with a relative
speed of less than 30 mph (48 km/h).
Side Monitoring
Rear Monitoring
Overtaking Traffic
If you pass another vehicle slowly (with a relative speed
of less than 10 mph (16 km/h) and the vehicle remains in
the blind spot for approximately 1.5 seconds, the warning
light will be illuminated. If the difference in speed
between the two vehicles is greater than 10 mph 3
(16 km/h), the warning light will not illuminate.
Overtaking/Passing
Overtaking/Approaching
The BSM system is designed not to issue an alert on The BSM system will not alert you of objects that are
stationary objects such as guardrails, posts, walls, foliage, traveling in the opposite direction of the vehicle in
berms, etc. However, occasionally the system may alert adjacent lanes.
on such objects. This is normal operation and your
vehicle does not require service.
Opposing Traffic
Stationary Objects
WARNING!
The Blind Spot Monitoring system is only an aid to
help detect objects in the blind spot zones. The BSM
system is not designed to detect pedestrians, bicy-
clists, or animals. Even if your vehicle is equipped 3
with the BSM system, always check your vehicles
mirrors, glance over your shoulder, and use your turn
signal before changing lanes. Failure to do so can
result in serious injury or death.
Rear Cross Path

The Rear Cross Path (RCP) feature is intended to aid the RCP Detection Zones
driver when backing out of parking spaces where their RCP monitors the rear detection zones on both sides of
vision of oncoming vehicles may be blocked. Proceed the vehicle, for objects that are moving toward the side of
slowly and cautiously out of the parking space until the the vehicle with a minimum speed of approximately 1 to
rear end of the vehicle is exposed. The RCP system will 2 mph (1 km/h to 3 km/h), to objects moving a maxi-
then have a clear view of the cross traffic and if an mum of approximately 10 mph (16 km/h), such as in
oncoming vehicle is detected, alert the driver. parking lot situations.
NOTE: In a parking lot situation, oncoming vehicles can Modes Of Operation
be obscured by vehicles parked on either side. If the Three selectable modes of operation are available in the
sensors are blocked by other structures or vehicles, the Electronic Vehicle Information Center (EVIC). Refer to
system will not be able to alert the driver. Electronic Vehicle Information Center (EVIC)/Personal
Settings (Customer-Programmable Features) in Under-
When RCP is on and the vehicle is in REVERSE, the
standing Your Instrument Panel for further information.
driver is alerted using both the visual and audible
alarms, including radio muting. Blind Spot Alert
When operating in Blind Spot Alert mode, the BSM
WARNING! system will provide a visual alert in the appropriate side
view mirror based on a detected object. However, when
RCP is not a Back Up Aid system. It is intended to be
the system is operating in RCP, the system will respond
used to help a driver detect an oncoming vehicle in a
with both visual and audible alerts when a detected
parking lot situation. Drivers must be careful when
object is present. Whenever an audible alert is requested,
backing up, even when using RCP. Always check
the radio is muted.
carefully behind your vehicle, look behind you, and
be sure to check for pedestrians, animals, other Blind Spot Alert Lights/Chime
vehicles, obstructions, and blind spots before back- When operating in Blind Spot Alert Lights/Chime mode,
ing up. Failure to do so can result in serious injury or the BSM system will provide a visual alert in the appro-
death. priate side view mirror based on a detected object. If the
turn signal is then activated, and it corresponds to an Blind Spot Alert Off
alert present on that side of the vehicle, an audible chime When the BSM system is turned off there will be no
will also be sounded. Whenever a turn signal and de- visual or audible alerts from either the BSM or RCP
tected object are present on the same side at the same systems.
time, both the visual and audio alerts will be issued. In
NOTE: The BSM system will store the current operating
addition to the audible alert the radio (if on) will also be 3
mode when the vehicle is shut off. Each time the vehicle
muted.
is started the previously stored mode will be recalled and
NOTE: used.
Whenever an audible alert is requested by the BSM
Astronomy Zone System Temporarily Unavailable
system, the radio is also muted.
When the vehicle enters this zone the blind spot system
If the hazard flashers are on, the system will request will become temporarily unavailable and the EVIC will
the appropriate visual alert only. display the message Blind spot system unavailable-
Astronomy zone. The side mirrors LEDs will be lit up
When the system is in RCP, the system shall respond
and stay lit until the vehicle exits the zone.
with both visual and audible alerts when a detected
object is present. Whenever an audible alert is re- Uconnect Phone IF EQUIPPED
quested, the radio is also muted. Turn/hazard signal Uconnect Phone is a voice-activated, hands-free, in-
status is ignored; the RCP state always requests the vehicle communications system. Uconnect Phone al-
chime. lows you to dial a phone number with your mobile
phone using simple voice commands (e.g., Call Uconnect Phone allows you to transfer calls between
Mike Work or Dial 248-555-1212). Your the system and your mobile phone as you enter or exit
mobile phones audio is transmitted through your vehi- your vehicle and enables you to mute the systems
cles audio system; the system will automatically mute microphone for private conversation.
your radio when using the Uconnect Phone.
The Uconnect Phone is driven through your
NOTE: The Uconnect Phone requires a mobile phone Bluetooth Hands-Free Profile mobile phone.
Uconnect features Bluetooth technology - the global
equipped with the Bluetooth Hands-Free Profile, Ver-
sion 0.96 or higher. See the Uconnect website for standard that enables different electronic devices to con-
supported phones. nect to each other without wires or a docking station, so
Uconnect Phone works no matter where you stow your
For Uconnect customer support, visit the following
mobile phone (be it your purse, pocket, or briefcase), as
websites:
long as your phone is turned on and has been paired to
www.chrysler.com/uconnect the vehicles Uconnect Phone. The Uconnect Phone
allows up to seven mobile phones to be linked to the
www.dodge.com/uconnect
system. Only one linked (or paired) mobile phone can be
www.jeep.com/uconnect used with the system at a time. The system is available in
English, Spanish, or French languages.
or call 18778558400
Voice Command Button
WARNING!
Actual button location may vary with the ra-
Any voice commanded system should be used only dio. The individual buttons are described in the
in safe driving conditions following local laws and Operation section.
phone use. All attention should be kept on the
roadway ahead. Failure to do so may result in a The Uconnect Phone can be used with any Hands-Free 3
collision causing serious injury or death. Profile certified Bluetooth mobile phone. See the
Uconnect website for supported phones. Refer to your
Uconnect Phone Button mobile service provider or the phone manufacturer for
The radio or steering wheel controls (if details.
equipped) will contain the two control buttons
The Uconnect Phone is fully integrated with the vehi-
(Uconnect Phone button and Voice Com-
cles audio system. The volume of the Uconnect Phone
mand button) that will enable you to
can be adjusted either from the radio volume control
access the system. When you press the button you will
knob or from the steering wheel radio control (right
hear the word Uconnect followed by a BEEP. The beep
switch), if so equipped.
is your signal to give a command.
The radio display will be used for visual prompts from
the Uconnect Phone such as CELL or caller ID on
certain radios.
Operation example, you can use the compound form voice
Voice commands can be used to operate the Uconnect command Phonebook New Entry, or you can break
Phone and to navigate through the Uconnect Phone the compound form command into two voice com-
menu structure. Voice commands are required after most mands: Phonebook and New Entry. Please re-
Uconnect Phone prompts. You will be prompted for a member, the Uconnect Phone works best when you
specific command and then guided through the available talk in a normal conversational tone, as if speaking to
options. someone sitting a few feet/meters away from you.
Prior to giving a voice command, one must wait for Voice Command Tree
the beep, which follows the Ready prompt or an- Refer to Voice Tree in this section.
other prompt.
Help Command
For certain operations, compound commands can be If you need assistance at any prompt, or if you want to
used. For example, instead of saying Setup and then know your options at any prompt, say Help following
Pair a Device, the following compound command the beep. The Uconnect Phone will play some of the
can be said: Pair a Bluetooth Device. options at any prompt if you ask for help.
For each feature explanation in this section, only the To activate the Uconnect Phone, simply press the
compound form of the voice command is given. You button and follow the audible prompts for directions.
can also break the commands into parts and say each Uconnect Phone sessions begin with a press of the
part of the command when you are asked for it. For button on the radio control head.
Cancel Command When prompted, after the beep, say Pair a Device
At any prompt, after the beep, you can say Cancel and and follow the audible prompts.
you will be returned to the main menu. However, in a
You will be asked to say a four-digit Personal Identi-
few instances the system will take you back to the
fication Number (PIN), which you will later need to
previous menu.
enter into your mobile phone. You can enter any
Pair (Link) Uconnect Phone To A Mobile Phone four-digit PIN. You will not need to remember this PIN 3
To begin using your Uconnect Phone, you must pair after the initial pairing process.
your compatible Bluetooth enabled mobile phone.
For identification purposes, you will be prompted to
To complete the pairing process, you will need to refer- give the Uconnect Phone a name for your mobile
ence your mobile phone Owners Manual. The phone. Each mobile phone that is paired should be
Uconnect website may also provide detailed instruc- given a unique phone name.
tions for pairing.
You will then be asked to give your mobile phone a
The following are general phone to Uconnect Phone priority level between one and seven, with one being
pairing instructions: the highest priority. You can pair up to seven mobile
phones to your Uconnect Phone. However, at any
Press the button to begin.
given time, only one mobile phone can be in use,
After the Ready prompt and the following beep, say connected to your Uconnect System. The priority
Device Pairing. allows the Uconnect Phone to know which mobile
phone to use if multiple mobile phones are in the Call By Saying A Name
vehicle at the same time. For example, if priority three
and priority five phones are present in the vehicle, the
Uconnect Phone will use the priority three mobile After the Ready prompt and the following beep, say
phone when you make a call. You can select to use a Call.
lower priority mobile phone at any time (refer to
The system will prompt you to say the name of the
Advanced Phone Connectivity in this section).
person you want to call.
Dial By Saying A Number
After the Ready prompt and the following beep, say
Press the button to begin. the name of the person you want to call. For example,
you can say John Doe, where John Doe is a previ-
ously stored name entry in the Uconnect phonebook
Dial.
or downloaded phonebook. To learn how to store a
The system will prompt you to say the number you name in the phonebook, refer to Add Names to Your
want to call. Uconnect Phonebook, in the phonebook.
For example, you can say 234-567-8901. The Uconnect system will confirm the name and
The Uconnect Phone will confirm the phone number then dial the corresponding phone number, which
and then dial. The number will appear in the display may appear in the display of certain radios.
of certain radios.
Add Names To Your Uconnect Phonebook After you are finished adding an entry into the phone-
book, you will be given the opportunity to add more
NOTE: Adding names to the Uconnect Phonebook is
phone numbers to the current entry or to return to the
recommended when the vehicle is not in motion.
main menu.
Press the button to begin. The Uconnect Phone will allow you to enter up to 32
After the Ready prompt and the following beep, say names in the phonebook with each name having up to 3
Phonebook New Entry. four associated phone numbers and designations. Each
language has a separate 32-name phonebook accessible
When prompted, say the name of the new entry. Use of only in that language. In addition, if equipped and
long names helps the Voice Command and it is recom- supported by your phone, Uconnect Phone automati-
mended. For example, say Robert Smith or Robert cally downloads your mobile phones phonebook.
instead of Bob.
Phonebook Download Automatic Phonebook
When prompted, enter the number designation (e.g., Transfer From Mobile Phone
Home, Work, Mobile, or Other). This will If equipped and specifically supported by your phone,
allow you to store multiple numbers for each phone- Uconnect Phone automatically downloads names (text
book entry, if desired. names) and number entries from your mobile phones
When prompted, recite the phone number for the phonebook. Specific Bluetooth Phones with Phone Book
phonebook entry that you are adding. Access Profile may support this feature. See Uconnect
website for supported phones.
To call a name from the Uconnect Phonebook or Only the mobile phones phonebook is downloaded.
downloaded Phonebook, follow the procedure in SIM card phonebook is not part of the Mobile phone-
Call by Saying a Name section. book.
Automatic download and update, if supported, begins This downloaded phonebook cannot be edited or
as soon as the Bluetooth wireless phone connection is deleted on the Uconnect Phone. These can only be
made to the Uconnect Phone, for example, after you edited on the mobile phone. The changes are trans-
start the vehicle. ferred and updated to Uconnect Phone on the next
phone connection.
A maximum of 1000 entries per phone will be down-
loaded and updated every time a phone is connected Edit Uconnect Phonebook Entries
to the Uconnect Phone.
NOTE:
Depending on the maximum number of entries down- Editing names in the phonebook is recommended
loaded, there may be a short delay before the latest when the vehicle is not in motion.
downloaded names can be used. Until then, if avail-
Automatic downloaded phonebook entries cannot be
able, the previously downloaded phonebook is avail-
deleted or edited.
able for use.
Only the phonebook of the currently connected mobile
phone is accessible.
After the Ready prompt and the following beep, say mobile and a home number, but you can add John
Phonebook Edit Entry. Does work number later using the Phonebook Edit
Entry feature.
You will then be asked for the name of the phonebook
entry that you wish to edit. Delete Uconnect Phonebook Entry
Next, choose the number designation (home, work, NOTE: Editing phonebook entries is recommended 3
mobile, or other) that you wish to edit. when the vehicle is not in motion.
When prompted, recite the new phone number for the Press the button to begin.
phonebook entry that you are editing.
After you are finished editing an entry in the phonebook, Phonebook Delete.
you will be given the opportunity to edit another entry in
After you enter the Phonebook Delete menu, you will
the phonebook, call the number you just edited, or return
then be asked for the name of the entry that you wish
to the main menu.
to delete. You can either say the name of a phonebook
Phonebook Edit Entry can be used to add another entry that you wish to delete or you can say List
phone number to a name entry that already exists in the Names to hear a list of the entries in the phonebook
phonebook. For example, the entry John Doe may have a from which you choose. To select one of the entries
from the list, press the button while the The Uconnect Phone will ask you to verify that you
Uconnect Phone is playing the desired entry and say wish to delete all the entries from the phonebook.
Delete.
After confirmation, the phonebook entries will be
After you enter the name, the Uconnect Phone will deleted.
ask you which designation you wish to delete: home,
Note that only the phonebook in the current language
work, mobile, other, or all. Say the designation you
is deleted.
wish to delete.
Note that only the phonebook entry in the current
deleted or edited.
language is deleted.
List All Names In The Uconnect Phonebook
deleted or edited. Press the button to begin.
Delete/Erase All Uconnect Phonebook Entries After the Ready prompt and the following beep, say
Phonebook List Names.
The Uconnect Phone will play the names of all the
phonebook entries, including the downloaded phone-
Phonebook Erase All.
book entries, if available.
To call one of the names in the list, press the Answer Or Reject An Incoming Call No Call
button during the playing of the desired name, and Currently In Progress
say Call. When you receive a call on your mobile phone, the
Uconnect Phone will interrupt the vehicle audio sys-
NOTE: The user can also exercise Edit or Delete
tem, if on, and will ask if you would like to answer the
operations at this point.
call. Press the button to accept the call. To reject the 3
The Uconnect Phone will then prompt you as to the call, press and hold the button until you hear a single
number designation you wish to call. beep, indicating that the incoming call was rejected.
The selected number will be dialed. Answer Or Reject An Incoming Call Call
Currently In Progress
Phone Call Features
If a call is currently in progress and you have another
The following features can be accessed through the
incoming call, you will hear the same network tones for
Uconnect Phone if the feature(s) are available on your
call waiting that you normally hear when using your
mobile service plan. For example, if your mobile service
mobile phone. Press the button to place the current
plan provides three-way calling, this feature can be
call on hold and answer the incoming call.
accessed through the Uconnect Phone. Check with
your mobile service provider for the features that you NOTE: The Uconnect Phone compatible phones in the
have. market today do not support rejecting an incoming call
when another call is in progress. Therefore, the user can Toggling Between Calls
only answer an incoming call or ignore it. If two calls are in progress (one active and one on hold),
press the button until you hear a single beep,
Making A Second Call While Current Call Is In
indicating that the active and hold status of the two calls
Progress
have switched. Only one call can be placed on hold at a
To make a second call while you are currently on a call,
time.
press the button and say Dial or Call followed
by the phone number or phonebook entry you wish to Conference Call
call. The first call will be on hold while the second call is When two calls are in progress (one active and one on
in progress. To go back to the first call, refer to Toggling hold), press and hold the button until you hear a
Between Calls in this section. To combine two calls, refer double beep indicating that the two calls have been
to Conference Call in this section. joined into one conference call.
Place/Retrieve A Call From Hold Three-Way Calling
To put a call on hold, press the button until you hear To initiate three-way calling, press the button while
a single beep. This indicates that the call is on hold. To a call is in progress, and make a second phone call, as
bring the call back from hold, press and hold the described under Making a Second Call While Current
button until you hear a single beep. Call is in Progress. After the second call has established,
press and hold the button until you hear a double NOTE: This may not be the last number dialed from the
beep, indicating that the two calls have been joined into Uconnect Phone.
one conference call.
Call Continuation
Call Termination Call continuation is the progression of a phone call on the
To end a call in progress, momentarily press the Uconnect Phone after the vehicle ignition key has been
button. Only the active call(s) will be terminated and if switched to OFF. Call continuation functionality avail- 3
there is a call on hold, it will become the new active call. able on the vehicle can be any one of three types:
If the active call is terminated by the phone far end, a call
After the ignition key is switched to OFF, a call can
on hold may not become active automatically. This is cell
continue on the Uconnect Phone either until the call
phone-dependent. To bring the call back from hold, press
ends, or until the vehicle battery condition dictates
and hold the button until you hear a single beep.
cessation of the call on the Uconnect Phone and
Redial transfer of the call to the mobile phone.
Press the button to begin. After the ignition key is switched to OFF, a call can
continue on the Uconnect Phone for a certain dura-
tion, after which the call is automatically transferred
Redial.
from the Uconnect Phone to the mobile phone.
The Uconnect Phone will call the last number that
was dialed from your mobile phone.
An active call is automatically transferred to the NOTE: After every Uconnect Phone language change
mobile phone after the ignition key is switched to OFF. operation, only the language-specific 32-name phone-
book is usable. The paired phone name is not language-
Uconnect Phone Features
specific and is usable across all languages.
Language Selection
Emergency Assistance
To change the language that the Uconnect Phone is
If you are in an emergency and the mobile phone is
using:
reachable:
Pick up the phone and manually dial the emergency
After the Ready prompt and the following beep, say number for your area.
the name of the language you wish to switch to
If the phone is not reachable and the Uconnect Phone is
English, Espanol, or Francais.
operational, you may reach the emergency number as
Continue to follow the system prompts to complete follows:
the language selection.
After selecting one of the languages, all prompts and
voice commands will be in that language.
Emergency and the Uconnect Phone will instruct
the paired mobile phone to call the emergency num-
WARNING!
ber. This feature is supported in the U.S., Canada, and
Mexico. To use your Uconnect Phone System in an emer-
gency, your mobile phone must be:
NOTE:
The emergency number dialed is based on the country turned on,
where the vehicle is purchased (911 for the U.S. and paired to the Uconnect System, 3
Canada and 060 for Mexico). The number dialed may and have network coverage.
not be applicable with the available mobile service and
area. Towing Assistance
If you need towing assistance:
If supported, this number may be programmable on
some systems. To do this, press the button and say Press the button to begin.
Setup, followed by Emergency. After the Ready prompt and the following beep, say
The Uconnect Phone does slightly lower your Towing Assistance.
chances of successfully making a phone call as to that NOTE:
for the mobile phone directly. The towing assistance number dialed is based on the
country where the vehicle is purchased (1-800-528-
2069 for the U.S., 1-877-213-4525 for Canada, 55-14-
3454 for Mexico City and 1-800-712-3040 for outside
Mexico City in Mexico). Please refer to the 24-Hour Working With Automated Systems
Towing Assistance coverage details on the DVD in This method is used in instances where one generally has
the Warranty Information Booklet and the 24-Hour to press numbers on the mobile phone keypad while
Towing Assistance references. navigating through an automated telephone system.
If supported, this number may be programmable on You can use your Uconnect Phone to access a voice
some systems. To do this, press the button and say mail system or an automated service, such as a paging
Setup, followed by Towing Assistance. service or automated customer service line. Some ser-
vices require immediate response selection. In some
Paging
instances, that may be too quick for use of the
To learn how to page, refer to Working with Automated
Uconnect Phone.
Systems. Paging works properly except for pagers of
certain companies, which time out a little too soon to When calling a number with your Uconnect Phone that
work properly with the Uconnect Phone. normally requires you to enter in a touch-tone sequence
on your mobile phone keypad, you can press the
Voice Mail Calling
button and say the sequence you wish to enter, followed
To learn how to access your voice mail, refer to Working
by the word Send. For example, if required to enter
with Automated Systems.
your PIN followed with a pound, (3 7 4 6 #), you can
press the button and say, 3 7 4 6 # Send. Saying
a number, or sequence of numbers, followed by Send,
is also to be used for navigating through an automated Barge In Overriding Prompts
customer service center menu structure, and to leave a The Voice Command button can be used when you
number on a pager. wish to skip part of a prompt and issue your voice
command immediately. For example, if a prompt is
You can also send stored Uconnect phonebook entries
asking Would you like to pair a phone, clear a..., you
as tones for fast and easy access to voice mail and pager
could press the button and say, Pair a Phone to 3
entries. To use this feature, dial the number you wish to
select that option without having to listen to the rest of
call and then press the button and say, Send. The
the voice prompt.
system will prompt you to enter the name or number and
say the name of the phonebook entry you wish to send. Turning Confirmation Prompts ON/OFF
The Uconnect Phone will then send the corresponding Turning confirmation prompts off will stop the system
phone number associated with the phonebook entry, as from confirming your choices (e.g., the Uconnect
tones over the phone. Phone will not repeat a phone number before you dial it).
NOTE: Press the button to begin.
You may not hear all of the tones due to mobile phone
network configurations. This is normal.
one of the following:
Some paging and voice mail systems have system time
Setup Confirmation Prompts On
out settings that are too short and may not allow the
use of this feature. Setup Confirmation Prompts Off
Phone And Network Status Indicators NOTE: Certain brands of mobile phones do not send the
If available on the radio and/or on a premium display dial ring to the Uconnect Phone to play it on the vehicle
such as the instrument panel cluster, and supported by audio system, so you will not hear it. Under this situa-
your mobile phone, the Uconnect Phone will provide tion, after successfully dialing a number the user may feel
notification to inform you of your phone and network that the call did not go through even though the call is in
status when you are attempting to make a phone call progress. Once your call is answered, you will hear the
using Uconnect Phone. The status is given for network audio.
signal strength, phone battery strength, etc.
Mute/Un-Mute (Mute OFF)
Dialing Using The Mobile Phone Keypad When you mute the Uconnect Phone, you will still be
You can dial a phone number with your mobile phone able to hear the conversation coming from the other
keypad and still use the Uconnect Phone (while dialing party, but the other party will not be able to hear you. In
via the mobile phone keypad, the user must exercise order to mute the Uconnect Phone:
caution and take precautionary safety measures). By
Press the button.
dialing a number with your paired Bluetooth mobile
phone, the audio will be played through your vehicles Following the beep, say Mute.
audio system. The Uconnect Phone will work the same
In order to un-mute the Uconnect Phone:
as if you dial the number using Voice Command.
Press the button.
Following the beep, say Mute off.
Advanced Phone Connectivity List Paired Mobile Phone Names
Transfer Call To And From Mobile Phone Press the button to begin.
The Uconnect Phone allows ongoing calls to be trans-
ferred from your mobile phone to the Uconnect Phone
Setup Phone Pairing.
without terminating the call. To transfer an ongoing call
from your Uconnect Phone paired mobile phone to the When prompted, say List Phones. 3
Uconnect Phone or vice versa, press the button
The Uconnect Phone will play the phone names of
and say Transfer Call.
all paired mobile phones in order from the highest to
Connect Or Disconnect Link Between The the lowest priority. To Select or Delete a paired
Uconnect Phone And Mobile Phone phone being announced, press the button and
Your mobile phone can be paired with many different say Select or Delete. Also, see the next two sec-
electronic devices, but can only be actively connected tions for an alternate way to Select or Delete a
with one electronic device at a time. paired phone.
If you would like to connect or disconnect the Bluetooth Select Another Mobile Phone
connection between your mobile phone and the This feature allows you to select and start using another
Uconnect Phone System, follow the instructions de- phone paired with the Uconnect Phone.
scribed in your mobile phone Users Manual.
After the Ready prompt and the following beep, say You can also press the button at any time while the
Setup Select Phone and follow the prompts. list is being played, and then choose the phone you
wish to delete.
You can also press the button at any time while the
list is being played, and then choose the phone that Things You Should Know About Your Uconnect
you wish to select. Phone
The selected phone will be used for the next phone Uconnect Phone Tutorial
call. If the selected phone is not available, the To hear a brief tutorial of the system features, press the
Uconnect Phone will return to using the highest button and say Uconnect Tutorial.
priority phone present in or near (approximately
Voice Training
within 30 ft (9 m)) the vehicle.
For users experiencing difficulty with the system recogniz-
Delete Uconnect Phone Paired Mobile Phones ing their voice commands or numbers, the Uconnect
Phone Voice Training feature may be used. To enter this
training mode, follow one of the two following procedures:
From outside the Uconnect Phone mode (e.g., from
Setup Phone Pairing.
radio mode):
At the next prompt, say Delete and follow the
Press and hold the button for five seconds until
prompts.
the session begins, or,
Press the button and say the Voice Training, This will delete all phone pairing, phone book entries,
System Training, or Start Voice Training command. and other settings in all language modes. The System will
prompt you before resetting to factory settings.
You can either press the Uconnect Phone button to
restore the factory setting or repeat the words and Voice Command
phrases when prompted by the Uconnect Phone. For
For best performance, adjust the rearview mirror to 3
best results, the Voice Training session should be com-
provide at least 12 in (1 cm) gap between the overhead
pleted when the vehicle is parked with the engine
console (if equipped) and the mirror.
running, all windows closed, and the blower fan
switched off. Always wait for the beep before speaking.
This procedure may be repeated with a new user. The Speak normally, without pausing, just as you would
system will adapt to the last trained voice only. speak to a person sitting a few feet/meters away from
you.
Reset
Make sure that no one other than you is speaking
press the button.
during a Voice Command period.
After the Ready prompt, and the following beep, say
Performance is maximized under:
Setup, then Reset.
low-to-medium blower setting,
low-to-medium vehicle speed, Phonebook (Downloaded and Uconnect Phone Lo-
cal) name recognition rate is optimized when the
low road noise,
entries are not similar.
smooth road surface,
Numbers must be spoken in single digits. 800 must
fully closed windows, be spoken eight-zero-zero not eight hundred.
dry weather condition. You can say O (letter O) for 0 (zero).
Even though the system is designed for users speaking Even though international dialing for most number
in North American English, French, and Spanish ac- combinations is supported, some shortcut dialing
cents, the system may not always work for some. number combinations may not be supported.
When navigating through an automated system such In a convertible vehicle, system performance may be
as voice mail, or when sending a page, at the end of compromised with the convertible top down.
speaking the digit string, make sure to say Send.
Far End Audio Performance
Storing names in the phonebook when the vehicle is
Audio quality is maximized under:
not in motion is recommended.
low-to-medium blower setting,
It is not recommended to store similar sounding
names in the Uconnect Phonebook. low-to-medium vehicle speed,
low road noise, Recent Calls
If your phone supports Automatic Phonebook Down-
smooth road surface,
load, Uconnect Phone can list your Outgoing, Incom-
fully closed windows, ing and Missed Calls.
dry weather conditions, and SMS
Uconnect Phone can read or send new messages on 3
operation from the drivers seat.
your phone.
Performance, such as audio clarity, echo, and loudness
Read Messages:
to a large degree rely on the phone and network, and
If you receive a new text message while your phone is
not the Uconnect Phone.
connected to Uconnect Phone, an announcement will
Echo at the phone far end can sometimes be reduced be made to notify you that you have a new text message.
by lowering the in-vehicle audio volume. If you wish to hear the new message:
In a convertible vehicle, system performance may be Press the button.
compromised with the convertible top down.
SMS Read or Read Messages.
Uconnect Phone will play the new text message for
you.
After reading a message, you can Reply or Forward List of Preset Messages:
the message using Uconnect Phone.
1. Yes
Send Messages:
2. No
You can send messages using Uconnect Phone. To send
a new message: 3. Where are you?
Press the button. 4. I need more direction.
After the Ready prompt and the following beep, say 5. LOL
SMS Send or Send Message.
6. Why
You can either say the message you wish to send or say
7. I love you
List Messages. There are 20 preset messages.
8. Call me
To send a message, press the button while the
system is listing the message and say Send. 9. Call me later
Uconnect Phone will prompt you to say the name or 10. Thanks
number of the person you wish to send the message to.
11. See You in 15 minutes
12. I am on my way
13. Ill be late After the Ready prompt and the following beep, say
Setup, SMS Incoming Message Announcement, you
14. Are you there yet?
will then be given a choice to change it.
15. Where are we meeting?
Bluetooth Communication Link
16. Can this wait? Mobile phones have been found to lose connection to the
Uconnect Phone. When this happens, the connection 3
17. Bye for now
can generally be reestablished by switching the phone
18. When can we meet off/on. Your mobile phone is recommended to remain in
Bluetooth ON mode.
19. Send number to call
Power-Up
20. Start without me
After switching the ignition key from OFF to either the
Turn SMS Incoming Announcement ON/OFF ON or ACC position, or after a language change, you
Turning the SMS Incoming Announcement OFF will stop must wait at least fifteen seconds prior to using the
the system from announcing the new incoming mes- system.
sages.
Press the button.
3
Voice Commands Voice Commands

Primary Alternate(s) Primary Alternate(s)
zero call
one cancel
two confirmation prompts
3
three continue
four delete
five dial
six download
seven edit
eight emergency
nine English
star (*) erase all
plus (+) Espanol
pound (#) Francais
add location help
all home
Voice Commands Voice Commands

Primary Alternate(s) Primary Alternate(s)
language return to main menu return or main menu
list names select phone select
list phones send
mobile set up phone settings or phone
mute set up
mute off towing assistance
new entry transfer call
no Uconnect Tutorial
other try again
pair a phone voice training
phone pairing pairing work
phonebook phone book yes
previous
record again
redial
General Information NOTE: Take care to speak into the Voice Interface
This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of
RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com-
following conditions: mands may be negatively affected by rapid speaking or a
raised voice level.
Changes or modifications not expressly approved by
the party responsible for compliance could void the 3
WARNING!
users authority to operate the equipment.
Any voice commanded system should be used only
in safe driving conditions following local laws. All
This device must accept any interference received, attention should be kept on the roadway ahead.
including interference that may cause undesired Failure to do so may result in a collision causing
operation. serious injury or death.
VOICE COMMAND IF EQUIPPED When you press the Voice Command button, you
Voice Command System Operation will hear a beep. The beep is your signal to give a
This Voice Command system allows you to command.
control your AM, FM radio, satellite radio, disc NOTE: If you do not say a command within a few
player, and a memo recorder. seconds, the system will present you with a list of options.
If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win-
options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is
for the beep, and say your command. set to low.
Pressing the Voice Command button while the At any point, if the system does not recognize one of your
system is speaking is known as barging in. The system commands, you will be prompted to repeat it.
will be interrupted, and after the beep, you can add or
To hear the first available Menu, press the Voice Com-
change commands. This will become helpful once you
mand button and say Help or Main Menu.
start to learn the options.
Commands
NOTE: At any time, you can say the words Cancel,
The Voice Command system understands two types of
Help or Main Menu.
commands. Universal commands are available at all
These commands are universal and can be used from any times. Local commands are available if the supported
menu. All other commands can be used depending upon radio mode is active.
the active application.
Changing the Volume
When using this system, you should speak clearly and at
1. Start a dialogue by pressing the Voice Command
a normal speaking volume.
button.
2. Say a command (e.g., Help).
3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM
volume to a comfortable level while the Voice Command To switch to the AM band, say AM or Radio AM. In
system is speaking. Please note the volume setting for this mode, you may say the following commands:
Voice Command is different than the audio system.
Frequency # (to change the frequency)
Main Menu
Next Station (to select the next station) 3
Start a dialogue by pressing the Voice Command
button. You may say Main Menu to switch to the main Previous Station (to select the previous station)
menu.
Radio Menu (to switch to the radio menu)
In this mode, you can say the following commands:
Main Menu (to switch to the main menu)
Radio (to switch to the radio mode)
Radio FM
Disc (to switch to the disc mode) To switch to the FM band, say FM or Radio FM. In
this mode, you may say the following commands:
Memo (to switch to the memo recorder)
Frequency # (to change the frequency)
Setup (to switch to system setup)
Next Station (to select the next station)
Previous Station (to select the previous station)
Menu Radio (to switch to the radio menu) Disc
To switch to the disc mode, say Disc. In this mode, you
may say the following commands:
Satellite Radio
Track (#) (to change the track)
To switch to satellite radio mode, say Sat or Satellite
Radio. In this mode, you may say the following com- Next Track (to play the next track)
mands:
Previous Track (to play the previous track)
Channel Number (to change the channel by its
spoken number)
Memo
Next Channel (to select the next channel)
To switch to the voice recorder mode, say Memo. In
Previous Channel (to select the previous channel) this mode, you may say the following commands:
List Channel (to hear a list of available channels) New Memo (to record a new memo) During the
recording, you may press the Voice Command
Select Name (to say the name of a channel)
button to stop recording. You proceed by saying one of
Menu Radio (to switch to the radio menu) the following commands:
Main Menu (to switch to the main menu) Save (to save the memo)
Continue (to continue recording) Switch to system setup
Delete (to delete the recording) Change to setup
Play Memos (to play previously recorded memos) Main menu setup or
During the playback you may press the Voice
Switch to setup
Command button to stop playing memos. You 3
proceed by saying one of the following commands: In this mode, you may say the following commands:
Repeat (to repeat a memo) Language English
Next (to play the next memo) Language French
Previous (to play the previous memo) Language Spanish
Delete (to delete a memo) Tutorial
Delete All (to delete all memos) Voice Training
Setup NOTE: Keep in mind that you have to press the Voice
To switch to system setup, you may say on of the Command button first and wait for the beep before
following: speaking the Barge In commands.
Change to setup
Voice Training
WARNING!
For users experiencing difficulty with the system recog-
nizing their voice commands or numbers the Uconnect It is dangerous to ride in a cargo area, inside or
Voice Voice Training feature may be used. outside of a vehicle. In a collision, people riding in
these areas are more likely to be seriously injured
1. Press the Voice Command button, say System
or killed.
Setup and once you are in that menu then say Voice
Training. This will train your own voice to the system Do not allow people to ride in any area of your
and will improve recognition. vehicle that is not equipped with seats and seat
belts. In a collision, people riding in these areas
2. Repeat the words and phrases when prompted by are more likely to be seriously injured or killed.
Uconnect Voice. For best results, the Voice Training Be sure everyone in your vehicle is in a seat and
session should be completed when the vehicle is parked, using a seat belt properly.
engine running, all windows closed, and the blower fan
switched off. This procedure may be repeated with a new Power Seats If Equipped
user. The system will adapt to the last trained voice only. Some models may be equipped with eight-way power
seats for the driver and front passenger. The power seat
SEATS
switches are located on the outboard side of the seat. The
Seats are a part of the Occupant Restraint System of the
switches control the movement of the seat cushion and
vehicle.
the seatback.
Adjusting The Seat Up Or Down
The height of the seats can be adjusted up or down. Pull
upward or push downward on the seat switch, the seat
will move in the direction of the switch. Release the
switch when the desired position has been reached.
Tilting The Seat Up Or Down 3
The angle of the seat cushion can be adjusted in four
directions. Pull upward or push downward on the front
or rear of the seat switch, the front or rear of the seat
cushion will move in the direction of the switch. Release
the switch when the desired position has been reached.
Driver Power Seat Switch Reclining The Seatback
1 Seat Switch 2 Seatback Switch The angle of the seatback can be adjusted forward or
rearward. Push the seatback switch forward or rearward,
Adjusting The Seat Forward Or Rearward
the seat will move in the direction of the switch. Release
The seat can be adjusted both forward and rearward.
the switch when the desired position has been reached.
Push the seat switch forward or rearward, the seat will
move in the direction of the switch. Release the switch
when the desired position has been reached.
WARNING! CAUTION!
Adjusting a seat while driving may be dangerous. Do not place any article under a power seat or
Moving a seat while driving could result in loss of impede its ability to move as it may cause damage to
control which could cause a collision and serious the seat controls. Seat travel may become limited if
injury or death. movement is stopped by an obstruction in the seats
Seats should be adjusted before fastening the seat path.
belts and while the vehicle is parked. Serious
injury or death could result from a poorly adjusted Power Lumbar If Equipped
seat belt. Vehicles equipped with power driver or passenger seats
Do not ride with the seatback reclined so that the may be also be equipped with power lumbar. The power
shoulder belt is no longer resting against your lumbar switch is located on the outboard side of the
chest. In a collision you could slide under the seat power seat. Push the switch forward to increase the
belt, which could result in serious injury or death. lumbar support. Push the switch rearward to decrease
the lumbar support.
WARNING!
Persons who are unable to feel pain to the skin
because of advanced age, chronic illness, diabetes,
spinal cord injury, medication, alcohol use, ex-
haustion or other physical condition must exercise 3
care when using the seat heater. It may cause burns
even at low temperatures, especially if used for
long periods of time.
Do not place anything on the seat that insulates
against heat, such as a blanket or cushion. This
may cause the seat heater to overheat. Sitting in a
Power Lumbar Switch seat that has been overheated could cause serious
Heated Seats If Equipped burns due to the increased surface temperature of
On some models, the front and rear seats may be the seat.
equipped with heaters in both the seat cushions and
seatbacks. Vehicles Equipped With Remote Start
On models that are equipped with remote start, the
drivers heated seat can be programmed to come on
during a remote start. Refer to Remote Starting System NOTE: Once a heat setting is selected, heat will be felt
If Equipped in Things To Know Before Starting Your within two to five minutes.
Vehicle for further information.
When the HIGH-level setting is selected, the heater will
Front Heated Seats provide a boosted heat level during the initial stages of
There are two heated seat switches that allow the driver operation. Then, the heat output will drop to the normal
and passenger to operate the seats independently. The HIGH-level. If the HIGH-level setting is selected, the
controls for each heater are located on the switch bank system will automatically switch to LOW-level after a
below the climate controls. maximum of 60 minutes of continuous operation. At that
time, the display will change from HIGH to LOW,
You can choose from HIGH, LOW or OFF heat settings.
indicating the change. The LOW-level setting will turn
Amber indicator lights in each switch indicate the level of
OFF automatically after a maximum of 45 minutes.
heat in use. Two indicator lights will illuminate for
HIGH, one for LOW and none for OFF. Rear Heated Seats
On some models, the second row seats are equipped with
Press the switch once to select HIGH-level
heaters. There are two heated seat switches that allow the
heating. Press the switch a second time to select
second row passengers to operate the seats indepen-
LOW-level heating. Press the switch a third
dently. The heated seat switches are located on the sliding
time to shut the heating elements OFF.
side door handle trim panels.
Press the switch once to select HIGH-level
heating. Press the switch a second time to select
LOW-level heating. Press the switch a third
time to shut the heating elements OFF.
NOTE: Once a heat setting is selected, heat will be felt
within two to five minutes. 3
When the HIGH-level setting is selected, the heater will
provide a boosted heat level during the initial stages of
operation. Then, the heat output will drop to the normal
HIGH-level. If the HIGH-level setting is selected, the
system will automatically switch to LOW-level after
Second Row Heated Seat Switch approximately 30 minutes of continuous operation. At
You can choose from HIGH, LOW or OFF heat settings. that time, the display will change from HIGH to LOW,
Amber indicator lights in each switch indicate the level of indicating the change. The LOW-level setting will turn
heat in use. Two indicator lights will illuminate for OFF automatically after approximately 45 minutes.
HIGH, one for LOW and none for OFF.
Manual Front/Second Row Seat Adjuster While sitting in the seat, pull up on the handle and slide
Both front seats are adjustable forward or rearward. The the seat forward or rearward. Release the bar once you
manual seat adjustment handle is located under the seat have reached the desired position. Then, using body
cushion at the front edge of each seat. pressure, move forward and rearward on the seat to be
sure that the seat adjusters have latched.
WARNING!
Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death.
Seats should be adjusted before fastening the seat
injury or death could result from a poorly adjusted
seat belt.
Manual Seat Adjuster
Manual Reclining Seats If Equipped To recline, lean forward slightly, lift the lever, then push
For models equipped with manual reclining seats, the back to the desired position and release the lever. Lean
recline lever is located on the outboard side of the seat. forward and lift the lever to return the seatback to its
normal position. Using body pressure, lean forward and
rearward on the seat to be sure the seatback has latched.
3
WARNING!
Do not ride with the seatback reclined so that the
shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt,
which could result in serious injury or death.
Manual Recline Lever

Head Restraints Active Head Restraints Front Seats
Head restraints are designed to reduce the risk of injury Active Head Restraints are passive, deployable compo-
by restricting head movement in the event of a rear nents, and vehicles with this equipment can not be
impact. Head restraints should be adjusted so that the top readily identified by any markings, only through visual
of the head restraint is located above the top of your ear. inspection of the head restraint. The head restraint will be
split in two halves, with the front half being soft foam
WARNING! and trim, the back half being decorative plastic.
The head restraints for all occupants must be prop- When AHRs deploy during a rear impact, the front half
erly adjusted prior to operating the vehicle or occu- of the head restraint extends forward to minimize the gap
pying a seat. Head restraints should never be ad- between the back of the occupants head and the AHR.
justed while the vehicle is in motion. Driving a This system is designed to help prevent or reduce the
vehicle with the head restraints improperly adjusted extent of injuries to the driver and front passenger in
or removed could cause serious injury or death in the certain types of rear impacts. Refer to Occupant Re-
event of a collision. straints in Things To Know Before Starting Your Ve-
hicle for further information.
To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted
restraint. To lower the head restraint, press the push forward and rearward. To tilt the head restraint closer to
button, located at the base of the head restraint, and push the back of your head, pull outward on the bottom of the
downward on the head restraint. head restraint. Push rearward on the bottom of the head
restraint to move the head restraint away from your
head. 3
Push Button
Active Head Restraint (Normal Position)

In the event of deployment of an Active Head Re-
straint, refer to Occupant Restraints/Resetting Active
Head Restraints (AHR) in Things To Know Before
Starting Your Vehicle for further information.
WARNING!
Do not place items over the top of the Active Head
Restraint, such as coats, seat covers or portable
DVD players. These items may interfere with the
operation of the Active Head Restraint in the event
of a collision and could result in serious injury or
Active Head Restraint (Tilted) death.
NOTE: (Continued)
The head restraints should only be removed by quali-
fied technicians, for service purposes only. If either of
the head restraints require removal, see your autho-
rized dealer.
Active Head Restraints may be deployed if they
are struck by an object such as a hand, foot or loose
cargo. To avoid accidental deployment of the Ac-
tive Head Restraint ensure that all cargo is se-
cured, as loose cargo could contact the Active Head
3
Restraint during sudden stops. Failure to follow
this warning could cause personal injury if the
Active Head Restraint is deployed.
Head Restraints Second Row Quad Seats

To raise the head restraint, pull upward on the head Push Button
restraint. To lower the head restraint, press the push Head Restraints Second Row Bench
button, located at the base of the head restraint, and push To raise the head restraint, pull upward on the head
downward on the head restraint. restraint. To lower the head restraint, press the push
button, located at the base of the head restraint, and push
downward on the head restraint.
Head Restraints Third Row NOTE: Seat will not stow in the storage bin unless the
The head restraint in the center position can be raised and armrests are raised.
lowered for tether routing. Refer to Occupant Re-
4. Slide the storage bin locking mechanism to the
straints in Things To Know Before Starting Your Ve-
LOCK position and then pull up on the storage bin
hicle for further information.
latch to open the cover.
Stow n Go Seating If Equipped
On vehicles equipped with Stow n Go seating, the
second and third row seats can be folded into the floor for
convenient storage.
Second Row Stow n Go
On vehicles equipped with Stow n Go seats, the seats
will fold and tumble in one motion.
1. Move the front seat fully forward.
2. Recline the front seatback fully forward.
3. Raise the armrests on the second row seat.
Storage Bin Cover Lock Release
5. Pull upward on the seatback recliner lever located on The non-adjustable head restraint and seatback will fold
the outboard side of the seat. automatically during the seat tumble. No additional
actuation is necessary.
Seatback Recliner Lever, Seat Tumble,

And Head Restraint Fold Lever Non-Adjustable Head Restraint
Automatic Folding Seatback Tumbled Second Row Seat

The seat will automatically tumble into position for easy 6. Push the seat into the storage bin.
storage.
CAUTION!
The storage bin cover must be locked and flat to
avoid damage from contact with the front seat tracks,
which have minimal clearance to the cover.
3
WARNING!
In a collision, serious injury could result if the seat
storage bin covers are not properly latched.
Do not drive the vehicle with the storage bin
covers open.
Seat In Storage Bin
Keep the storage bin covers closed and latched
7. Close the storage bin cover. while the vehicle is in motion.
Do not use a storage bin latch as a tie down.
To Unstow Second Row Seats
1. Pull up on the storage bin latch to open the cover.
2. Pull up on the strap to lift the seat out of the storage
bin and push the seat rearward to latch the seat anchors.
3. Lift the seatback to the full upright position.
4. Return the head restraint to its upright position, close
the storage bin cover and slide the storage bin locking
mechanism to the Unlocked position.
Stow n Go Seat Folded And Latched Position
To tumble or stow the seat from the folded and latched Raising The Seatback
position: return the seatback and head restraint to the
2. Return the head restraint to the upright position.
upright position. Then pull up on the seatback recliner
lever on the outboard side of the seat to fold head rest
and seatback and tumble seat forward.
1. Return the seatback to the upright position.
Easy Entry Second Row
The second row Stow n Go seats allow easy entry to the
third row seat or rear cargo area.
Pull up on the seatback recliner lever on the outboard
side of the seat.
3
Raising The Head Restraint

3. Pull up on the seatback recliner lever on the outboard
side of the seat to fold head rest and seatback and tumble
seat forward.
Seatback Recliner Lever, Seat Tumble,

And Head Restraint Fold Lever
The seat will automatically fold into position for easy
entry into the third row.
WARNING!
In the event of a collision you could be injured if the
seat is not fully latched.
Quad Seats If Equipped

Both Quad seats are adjustable forward or rearward. The
manual seat adjustment handle is located under the seat
cushion at the front edge of each seat.
Manual Seat Adjuster
While sitting in the seat, pull up on the handle and slide
the seat forward or rearward. Release the bar once you
have reached the desired position. Then, using body
pressure, move forward and rearward on the seat to be
sure that the seat adjusters have latched.
WARNING!
Adjusting a seat while driving may be dangerous.
Moving a seat while driving could result in loss of
control which could cause a collision and serious
injury or death. 3
Seats should be adjusted before fastening the seat
injury or death could result from a poorly adjusted
seat belt.
Manual Recline
To recline, lean forward slightly, lift the lever, then push Recline Lever
back to the desired position and release the lever. Lean WARNING!
forward and lift the lever to return the seatback to its
normal position. Using body pressure, lean forward and Do not ride with the seatback reclined so that the
rearward on the seat to be sure the seatback has latched. shoulder belt is no longer resting against your chest.
In a collision you could slide under the seat belt,
which could result in serious injury or death.
Fold-Flat Easy Entry
To fold the seat, lift the recliner lever to the full upward The Quad seats can be tilted forward for easy entry into
position and push the seatback forward until it rests on the third row. With the Quad seat in the fold-flat position,
the seat cushion. lift up on the easy entry lever located near the bottom of
the seat and lift the seat forward.
Fold-Flat Quad Seat

Easy Entry Lever
For passengers seated in the third row, there is a pull To provide additional space behind the second row seats,
strap located on the outboard side of the seat near the the seats can be folded forward.
bottom of the seat back. Third row passengers can pull on
With the seat in its fold-flat position, pull upward on the
the strap and push the Quad seat forward for folding the
easy-access release lever and lift the seat into the desired
seatback and accessing the easy entry lever.
position.
3
Pull Strap for Third Row Passengers

Fold-Flat Release Lever
Pull out the retainer strap from the sewn-in pocket
located on the base of the seat cushion.
B-Pillar Grab Handle

Secure the retainer strap to the inside grab handle located
Retainer Strap on the B-Pillar. When not in use, store the strap in the
Place the strap around the grab handle located on the sewn-in pocket located on the base of the seat cushion.
B-Pillar. Before securing the strap, adjust the buckle for
proper fit.
WARNING!
To reduce the risk of personal injury:
Retainer strap must always be securely attached to
grab handle when seat is folded forward and
vehicle is moving. 3
Never occupy the seat or the center seat behind a
seat that has been folded forward.
Retainer Strap
Removal Second Row Bench Seat If Equipped
The Quad seats can be removed if additional storage is While the bench seat does not stow in the floor, it is
needed. With the seat in the easy entry position, lift the removable for added cargo space.
cross beam forward and up to release the front anchor
latches.
Second Row Bench Seat
Cross Beam for Seat Removal

Release levers are located on the rear leg assemblies, near To reinstall the seat, align the seat into the detent posi-
the floor. To remove the seat, squeeze each release handle tions on the floor. Squeeze the release handle and rotate
and rotate downwards to deploy the wheels. A lock upward until the lock indicator button returns into the
indicator button pops up when the seat is unlocked. The handle.
seat assembly can now be removed from the vehicle and
moved on its Easy Out Rollers. WARNING! 3
If not properly latched, the bench seats could become
loose. Personal injuries could result. After reinstall-
ing these seats, be sure the red indicator button on
the release handles return into the handles.
Release Handles
Third Row Power Recline If Equipped Third Row Power Folding Seat If Equipped
The power recline feature, located on the side of the seat A one-touch power folding seat switch is located in the
cushion, adjusts the seatback angle forward/rearward left rear trim panel as part of a switch bank.
for occupant comfort.
NOTE: Lower the head restraint by pulling on the
release strap marked 1 located on the outboard side of
the head restraint.
Third Row Power Seat Switch
Head Restraint Release Strap 1

The switch is only functional when the liftgate is open Left and right third row seats can be folded individually
and the vehicle is in PARK. or together. The third row power folding seat adjusts to
the following positions using the switch bank located on
the left rear trim panel:
One Touch Folding Seat Third Row

The rear switch bank allows multiple power folding and
unfolding positions for the third row seats. Rear Panel Power Switch Bank
1 Open to Normal 2 Stow
3 Tailgate/Fold Flat 4 Right/Left Seats/Both Seats
NOTE: 2. Lower the outboard head restraints by pulling on the
Disconnect the center shoulder belt from the small release strap marked 1 located on the outboard side of
buckle and lower the head restraints before attempting the head restraint.
to fold/stow the power third row seats.
To abort seat operation while seat is in motion, press a
different seat position selector switch to stop the seat.
Once the seat stops moving, then the desired position
can be selected.
The third row power seat system includes obstacle
detection for safe operation. When the system detects
an obstacle, the motors will stop and reverse the
motion a short distance to move the seat away from
the obstacle. Should this occur, remove the obstacle
and press the button again, for the desired position.
Head Restraint Release Strap 1
Manually Folding Third Row Seats If Equipped
1. Lower the center head restraint down to the seatback
by pushing the button on the guide and pushing the head
restraint down.
3. Pull release strap marked 2 located on the rear of the 4. Pull release strap marked 3 to release the anchors.
seat to lower the seatback.
Release Strap 3
Release Strap 2
5. Pull release strap marked 4 and tumble the seat
rearward into the storage bin.
Stowed Third Row Seat

To Unfold Third Row Seats
Release Strap 4
1. Pull up on the assist strap to lift the seat out of the
storage bin and push the seat forward until the anchors
latch.
2. Pull release strap marked 2 to unlock the recliner.
3. Pulling strap 4 releases the seatback to return to its 2. To restore the seat to its upright position, lift up on the
full upright position. seatback and push forward until the anchors latch.
4. Raise the head restraint to its upright position.
WARNING!
WARNING! To avoid serious injury or death, never operate the
vehicle with occupants in the third row seat while in 3
In a collision, you or others in your vehicle could be
the tailgate mode.
injured if seats are not properly latched to their floor
attachments. Always be sure the seats are fully
Plastic Grocery Bag Retainer Hooks
latched.
Retainer hooks which will hold plastic grocery bag
handles are built into the seatbacks of all rear seats and
Tailgate Mode
some front seats. The floor supports the partial weight of
1. Pull release strap 3, then pull release strap 4 to the bagged goods.
rotate the entire seat rearward.
DRIVER MEMORY SEAT IF EQUIPPED
The Memory Buttons 1 and 2 on the drivers door panel
can be programmed to recall the drivers seat, drivers
outside mirror, adjustable brake and accelerator pedals,
and radio station preset settings. Your Remote Keyless
Entry (RKE) transmitters can also be programmed to Setting Memory Positions And Linking RKE
recall the same positions when the UNLOCK button is Transmitter To Memory
pressed.
NOTE: Each time the SET (S) button and a numbered
button (1 or 2) is pressed, you erase the memory settings
for that button and store a new one.
1. Insert the ignition key and turn the ignition switch to
the ON position.
2. Press the driver door MEMORY button number 1 if
you are setting the memory for driver 1, or button
number 2 if you are setting the memory for driver 2. The
system will recall any stored settings. Wait for the system
to complete the memory recall before continuing to
Step 3.
Driver Memory Switch 3. Adjust the drivers seat, recliner, and drivers side-
Your vehicle may have been delivered with two RKE view mirror to the desired positions.
transmitters. Only one RKE transmitter can be linked to 4. Adjust the brake and accelerator pedals to the desired
each of the memory positions. positions.
5. Turn on the radio and set the radio station presets (up 11. Select Remote Linked to Memory in the Electronic
to 10 AM and 10 FM stations can be set). Vehicle Information Center (EVIC) and enter Yes. Refer
to Electronic Vehicle Information Center (EVIC)/
6. Turn the ignition switch to the OFF position and
Customer-Programmable Features in Understanding
remove the key.
7. Press and release the SET (S) button located on the 3
12. Repeat the above steps to set the next Memory
drivers door.
position using the other numbered Memory button or to
8. Within five seconds, press and release MEMORY link another RKE transmitter to memory.
button 1 or 2 on the drivers door. The next step must be
Memory Position Recall
performed within 5 seconds if you desire to also use a
RKE transmitter to recall memory positions. NOTE: The vehicle must be in PARK to recall memory
positions. If a recall is attempted when the vehicle is not
9. Press and release the LOCK button on one of the RKE
in PARK, a message will be displayed in the EVIC.
transmitters.
To recall the memory settings for driver one, press
10. Insert the ignition key and turn the ignition switch to
MEMORY button 1 on the drivers door or the UNLOCK
the ON position.
button on the RKE transmitter linked to memory position
1.
To recall the memory setting for driver two, press 3. Press and release the memory SET (S) button located
MEMORY button 2 on the drivers door or the UNLOCK on the drivers door. A chime will sound signaling that
button on the RKE transmitter linked to Memory Position you are in the memory set mode.
2.
4. Within five seconds, press and release MEMORY
A recall can be cancelled by pressing any of the button 1 on the drivers door. A chime will sound
MEMORY buttons on the drivers door during a recall (S, signaling to you that the driver memory has been set.
1, or 2). When a recall is cancelled, the drivers seat,
5. Within five seconds, press and release the UNLOCK
drivers mirror, and the pedals stop moving. A delay of
button on the RKE transmitter. A chime will sound
one second will occur before another recall can be
signaling to you that the RKE transmitter link has been
selected.
successfully disabled.
To Disable RKE Transmitter Linked To Memory To disable another RKE transmitter linked to either
1. Turn the ignition switch to the OFF position and Memory Position, repeat Steps 1 to 5 for each RKE
remove the key. transmitter.
2. Press and release MEMORY button 1. The system will NOTE: Once programmed, all RKE transmitters linked
recall any memory settings stored in position 1. Wait for to memory can be easily enabled or disabled at one time.
the system to complete the memory recall before continu- Refer to Electronic Vehicle Information Center (EVIC)/
ing to Step 3. Customer-Programmable Features in Understanding
Easy Entry/Exit Seat When you remove the key from the ignition switch the
(Available With Memory Seat ONLY) driver seat will move to a position 0.3 in (7.7 mm)
This feature provides automatic driver seat positioning to forward of the rear stop if the driver seat position is
enhance driver mobility when entering and exiting the between 0.9 2.7 in (22.7 67.7 mm) forward of the
vehicle. rear stop. The seat will return to its previously set
position when you insert the key into the ignition 3
The distance the driver seat moves depends on where
switch and turn it out of the LOCK position.
you have the driver seat positioned when you remove the
key from the ignition switch. The Easy Entry/Easy Exit feature is disabled when the
driver seat position is less than 0.9 in (22.7 mm)
When you remove the key from the ignition switch,
forward of the rear stop. At this position, there is no
the driver seat will move about 2.4 in (60 mm)
benefit to the driver by moving the seat for Easy Exit
rearward if the driver seat position is greater than or
or Easy Entry.
equal to 2.7 in (67.7 mm) forward of the rear stop. The
seat will return to its previously set position when you Each stored memory setting will have an associated Easy
insert the key into the ignition switch and turn it out of Entry and Easy Exit Position.
the LOCK position.
NOTE: The Easy Entry/Easy Exit feature can be en-
abled or disabled through the programmable features in
the Electronic Vehicle Information Center (EVIC). If your
vehicle is not equipped with an EVIC, your dealership
can activate/deactivate this feature for you. For details,
refer to Electronic Vehicle Information Center (EVIC)/
TO OPEN AND CLOSE THE HOOD

To open the hood, two latches must be released.
1. Pull the hood release lever located on the instrument
Hood Release Lever
panel, below the steering column.
2. Move to the front of the vehicle and look inside the
center of the hood opening. Locate, then push the safety
catch downward while raising the hood at the same time.
Safety Lever Location Hood Prop Rod

Use the hood prop rod to secure the hood in the open
position.
LIGHTS
CAUTION!
Headlight Switch
To prevent possible damage, do not slam the hood to
The headlight switch is located on the left side of the
close it. Lower the hood until it is open approxi-
instrument panel. The switch controls the operation of
mately 12 in (30 cm) and then drop it. This should
the headlights, parking lights, instrument panel lights,
secure both latches. Never drive your vehicle unless
interior lights and the fog lights.
the hood is fully closed, with both latches engaged.
WARNING!
Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.
Headlight Switch With Halo Control

Rotate the headlight switch clockwise to the first detent Headlights On With Wipers If Equipped
for parking light and instrument panel light operation. When your headlights are in the AUTO mode and the
Rotate the headlight switch to the second detent for engine is running, the headlights will automatically turn
headlight, parking light and instrument panel operation. on when the wiper system is also turned on. Headlights
on when windshield wipers are on may be found on
Automatic Headlights If Equipped
vehicles equipped with an automatic headlight system. 3
This system automatically turns your headlights on or off
Refer to Electronic Vehicle Information Center (EVIC)/
based on ambient light levels. To turn the system on, turn
the headlight switch to the extreme counterclockwise
position aligning the indicator with the AUTO on the
headlight switch. When the system is on, the Headlight Headlight Delay If Equipped
Time Delay feature is also on. This means your headlights This feature provides the safety of headlight illumination
will stay on for up to 90 seconds after you turn the for up to 90 seconds after exiting your vehicle.
ignition switch OFF. To turn the Automatic System off,
To activate the delay feature, turn OFF the ignition switch
turn the headlight switch clockwise to the O (OFF)
while the headlights are still on. Then turn off the
position.
headlights within 45 seconds. The 90 second delay inter-
NOTE: The engine must be running before the head- val begins when headlight switch is turned off. If the
lights will come on in the Automatic mode. headlights or parking lights are turned back on or the
ignition switch is turned ON, the delay will be cancelled.
When exiting the vehicle the driver can choose to have Lights-On Reminder
the headlights remain on for 30, 60 or 90 seconds or not If the headlights or the parking lights are left on, or if the
remain on. To change the timer setting, see your autho- dimmer control is in the extreme top position after the
rized dealer. ignition switch is turned OFF, a chime will sound when
the drivers door is opened.
The headlight delay time is programmable on vehicles
equipped with an EVIC. Refer to Electronic Vehicle Daytime Running Lights If Equipped
Information Center (EVIC)/Customer-Programmable The headlights on your vehicle will illuminate when the
Features in Understanding Your Instrument Panel for engine is started and the transmission is in any gear
further information. except PARK. This provides a constant lights on condi-
tion until the ignition is turned OFF. The lights illuminate
If the headlights are turned off before the ignition, they
at less than 50% of normal intensity. If the parking brake
will turn off in the normal manner.
is applied, the Daytime Running Lights (DRL) will turn
NOTE: The headlights must be turned off within 45 sec- off. Also, if a turn signal is activated, the DRL lamp on the
onds of turning the ignition OFF to activate this feature. same side of the vehicle will turn off for the duration of
the turn signal activation. Once the turn signal is no
longer active, the DRL lamp will illuminate.
Front Fog Lights If Equipped
To activate the front fog lights, turn on the parking
lights or the low beam headlights and push in the
headlight switch control knob. Pressing the head-
light switch control knob in a second time will turn the
front fog lights off. 3
Dimmer Controls
The dimmer switch is located next to the headlight
switch.
Dimmer Control
With the parking lights or headlights on, rotating the
dimmer control upward will increase the brightness of
the instrument panel lights.
Interior Lighting On NOTE: The key must be out of the ignition switch or the
Rotate the left dimmer control completely upward to the ignition switch must be in the OFF position for this
second detent (extreme top position) to turn on the feature to operate.
interior lights. The interior lights will remain on when the
Interior Lighting Off
dimmer control is in this position.
Rotate the left dimmer control to the off position (extreme
Interior lights are also turned on when a door or liftgate bottom). The interior lights will remain off when the
is opened, the Remote Keyless Entry (RKE) transmitter is doors or liftgate are open.
activated, or when the dimmer control is moved to the
Parade Mode (Daytime Brightness Feature)
extreme top.
Rotate the left dimmer control to the first detent. This
The interior lights will automatically turn off in approxi- feature brightens the odometer, radio and overhead
mately 10 minutes for the first activation and 90 seconds displays when the parking lights or headlights are on.
every activation thereafter until the engine is started, if
Halo Lights If Equipped
one of the following occur:
Halo lights are strategically placed soft lighting that help
A door, sliding door or the liftgate is left open to illuminate specific areas to aid the occupants in
locating specific features while driving at night.
Any overhead reading light is left on
The Halo control switch is located to the right of the
dimmer switch.
Multifunction Lever
The multifunction lever is located on the left side of the
steering column.
Halo Control
To activate the Halo lights, rotate the Halo
switch control upward or downward to in-
crease or decrease the lighting. Multifunction Lever
The multifunction lever controls the:
Turn Signals
Headlight Beams Low/High Lane Change Assist
Tap the lever up or down once, without moving beyond
Flash-To-Pass (Optical Horn)
the detent, and the turn signal (right or left) will flash
Front and Rear Wipers Washer Functions three times then automatically turn off.
Turn Signals High/Low Beam Switch
Move the multifunction lever up or down and the arrows When the headlights are turned on, pushing the multi-
on each side of the instrument cluster flash to show function lever toward the instrument panel will switch
proper operation of the front and rear turn signal lights. from low beams to high beams. Pulling back to the
neutral position returns the headlights to the low beam
NOTE: If either light remains on and does not flash, or
operation.
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is Flash-To-Pass
moved, it would suggest that the indicator bulb is You can signal another vehicle with your headlights by
defective. lightly pulling the multifunction lever toward you. This
will cause the headlights to turn on at high beam and
Turn Signal Warning
remain on until the lever is released.
If the vehicle electronics sense that the vehicle has
traveled at over 18 mph (29 km/h) for about 1 mile
(1.6 km) with the turn signals on, a chime will sound to
alert the driver.
Battery Protection
This feature provides battery protection to avoid wearing
down the battery if the headlights, parking lights, or
front fog lights are left on for extended periods of time
when the ignition switch is in the LOCK position. After
eight minutes of the ignition switch being in the LOCK 3
position and the headlight switch in any position other
than OFF or AUTO, the lights will turn off automatically
until the next cycle of the ignition switch or headlight
switch.
The battery protection feature will be disabled if the
ignition switch is turned to any other position other than Washer And Wiper Controls
LOCK during the eight minute delay.
NOTE: Always remove any buildup of snow that pre-
WINDSHIELD WIPER AND WASHERS vents the windshield wiper blades from returning to the
The wipers and washers are operated by a switch within off position. If the windshield wiper switch is turned off
the multifunction lever. Rotate the end of the multifunc- and the blades cannot return to the off position, damage
tion lever to select the desired wiper speed. to the wiper motor may occur.
At driving speeds above 10 mph (16 km/h), the delay
WARNING!
can be regulated from a maximum of approximately
Sudden loss of visibility through the windshield 18 second between cycles (first detent), to a cycle every
could lead to a collision. You might not see other one second (fifth detent).
vehicles or other obstacles. To avoid sudden icing of
Windshield Wiper Operation
the windshield during freezing weather, warm the
Rotate the end of the lever upward, to the first detent past
windshield with the defroster before and during
the intermittent settings for low-speed wiper operation.
windshield washer use.
Rotate the end of the lever upward to the second detent
past the intermittent settings for high-speed operation.
Intermittent Wiper System
Use the intermittent wiper system when weather condi- Windshield Washers
tions make a single wiping cycle, with a variable pauseTo use the Washer, push on the end of the lever to the
between cycles, desirable. Rotate the end of the wiper/second detent and hold while spray is desired. If the lever
is pushed while on the intermittent setting, the wipers
washer control lever to one of the first five detents to
select the desired delay interval. will turn on and operate for several wipe cycles after the
lever is released, and then resume the intermittent inter-
NOTE:
val previously selected. If the lever is pushed while the
If the vehicle is moving less than 10 mph (16 km/h),
wipers are in the off position, the wipers will operate
delay times will be doubled.
several wipe cycles, then turn off.
Mist Feature Rain Sensing Wipers If Equipped
Press the end of the multifunction lever inward (toward This feature senses moisture on the windshield and auto-
the steering column) to the first detent and release for a matically activates the wipers for the driver. This feature is
single wiping cycle. especially useful for road splash or overspray from the
windshield washers of the vehicle ahead. Rotate the end of
NOTE: The mist feature does not activate the washer
the multifunction lever to one of the five intermittent 3
pump; therefore, no washer fluid will be sprayed on the
wiper sensitivity settings to activate this feature.
windshield. The wash function must be used in order to
spray the windshield with washer fluid. The sensitivity of the system is adjustable from the
multifunction lever. Wiper sensitivity position 3 has been
Rear Wiper And Washer
calibrated for best overall wiping sensitivity. If the opera-
Rotating the rotary ring to the first detent activates the
tor desires more wiping sensitivity, they may select
rear intermittent wipers. To activate the washers, rotate
sensitivity positions 4 or 5. If the operator desires less
the rotary ring fully forward and the washers will spray
wiping sensitivity, they may select sensitivity positions 2
until the ring is released, and then resume the intermit-
or 1. Place the multifunction lever in the OFF position
tent interval.
when not using the system.
NOTE: Rear window wipers function in the intermittent
NOTE:
wiper speed only.
The Rain Sensing feature will not operate when the
wiper speed is in the low or high position.
The Rain Sensing feature may not function properly wiper control on the multifunction lever is moved, or
when ice or dried saltwater is present on the wind- the vehicle speed becomes greater than 0 mph (0 km/h),
shield. or the outside temperature rises above freezing.
Use of Rain-X or products containing wax or silicone Neutral Wipe Inhibit The Rain Sensing feature will
may reduce rain sensor performance. not operate when the ignition is ON, and the trans-
mission shift lever is in the NEUTRAL position, and
The Rain Sensing feature can be turned on and off
the vehicle speed is less than 5 mph (8 km/h), unless
through the EVIC (if equipped). Refer to Electronic
the wiper control on the multifunction lever is moved
Vehicle Information Center (EVIC)/Personal Settings
or the shift lever is moved out of the NEUTRAL
(Customer-Programmable Features) in Understand-
position.
ing Your Instrument Panel for further information.
Remote Start Mode Inhibit On vehicles equipped
The Rain Sensing system has protective features for the
with Remote Starting system, Rain Sensing wipers are
wiper blades and arms. It will not operate under the
not operational when the vehicle is in the remote start
following conditions:
mode. Once the operator is in the vehicle and has
Low Temperature Wipe Inhibit The Rain Sensing placed the ignition switch in the RUN position, rain
feature will not operate when the ignition is first sensing wiper operation can resume, if it has been
switched ON, and the vehicle is stationary, and the selected, and no other inhibit conditions (mentioned
outside temperature is below 32F (0C), unless the previously) exist.
TILT/TELESCOPING STEERING COLUMN To unlock the steering column, push the lever downward
This feature allows you to tilt the steering column (toward the floor). To tilt the steering column, move the
upward or downward. It also allows you to lengthen or steering wheel upward or downward as desired. To
shorten the steering column. The tilt/telescoping lever is lengthen or shorten the steering column, pull the steering
located below the steering wheel at the end of the wheel outward or push it inward as desired. To lock the
steering column. steering column in position, push the lever upward until 3
fully engaged.
WARNING!
Do not adjust the steering column while driving.
Adjusting the steering column while driving or driv-
ing with the steering column unlocked, could cause
the driver to lose control of the vehicle. Be sure the
steering column is locked before driving your ve-
hicle. Failure to follow this warning may result in
serious injury or death.
Tilt/Telescoping Lever
HEATED STEERING WHEEL IF EQUIPPED NOTE: The engine must be running for the heated
The steering wheel contains a heating element that helps steering wheel to operate.
warm your hands in cold weather. The heated steering
Vehicles Equipped With Remote Start
wheel has only one temperature setting. Once the heated
On models that are equipped with remote start, the
steering wheel has been turned on it will operate for
heated steering wheel can be programmed to come on
approximately 58 to 70 minutes before automatically
during a remote start. Refer to Remote Starting System
shutting off. The heated steering wheel can shut off early
If Equipped in Things to Know Before Starting Your
or may not turn on when the steering wheel is already
Vehicle for further information.
warm.
The heated steering wheel switch is located on the switch WARNING!
bank below the climate controls.
Persons who are unable to feel pain to the skin
Press the switch to turn on the heated because of advanced age, chronic illness, diabetes,
steering wheel. The light on the switch spinal cord injury, medication, alcohol use, ex-
will illuminate to indicate the steering haustion, or other physical conditions must exer-
wheel heater is on. Pressing the switch cise care when using the steering wheel heater. It
a second time will turn off the heated may cause burns even at low temperatures, espe-
steering wheel and light indicator. cially if used for long periods.
(Continued)
Do not place anything on the steering wheel that
insulates against heat, such as a blanket or steering
wheel covers of any type and material. This may
cause the steering wheel heater to overheat.
3
ADJUSTABLE PEDALS IF EQUIPPED
The adjustable pedals system is designed to allow a
greater range of driver comfort for steering wheel tilt and
seat position. This feature allows the brake, accelerator,
and clutch pedals (if equipped) to move toward or away
from the driver to provide improved position with the Adjustable Pedal Switch
steering wheel. Press the switch forward to move the pedals forward
(toward the front of the vehicle).
The switch is located on the left side of the steering
column. Press the switch rearward to move the pedals rearward
(toward the driver).
The pedals can be adjusted with the ignition OFF.
The pedals cannot be adjusted when the vehicle is in
WARNING!
REVERSE or when the Electronic Speed Control Sys-
tem is on. The following messages will be displayed Do not adjust the pedals while the vehicle is moving.
on vehicles equipped with the Electronic Vehicle In- You could lose control and have an accident. Always
formation System (EVIC) if the pedals are attempted to adjust the pedals while the vehicle is parked.
be adjusted when the system is locked out (Adjust-
able Pedal Disabled Cruise Control Engaged or ELECTRONIC SPEED CONTROL IF EQUIPPED
Adjustable Pedal Disabled Vehicle In Reverse. When engaged, the Electronic Speed Control takes over
accelerator operations at speeds greater than 25 mph
CAUTION! (40 km/h).
Do not place any article under the adjustable pedals The Electronic Speed Control buttons are located on the
or impede its ability to move, as it may cause damage right side of the steering wheel.
to the pedal controls. Pedal travel may become lim-
ited if movement is stopped by an obstruction in the
adjustable pedals path.
System can be reactivated by pushing the Electronic
Speed Control ON/OFF button and resetting the desired
vehicle set speed.
To Activate
Push the ON/OFF button. The Cruise Indicator Light in
the instrument cluster will illuminate. To turn the system 3
off, push the ON/OFF button a second time. The Cruise
Indicator Light will turn off. The system should be
turned off when not in use.
WARNING!
1 ON/OFF 2 RES + Leaving the Electronic Speed Control system on
4 CANCEL 3 SET -
when not in use is dangerous. You could accidentally
NOTE: In order to ensure proper operation, the Elec- set the system or cause it to go faster than you want.
tronic Speed Control System has been designed to shut You could lose control and have an accident. Always
down if multiple Speed Control functions are operated at leave the system OFF when you are not using it.
the same time. If this occurs, the Electronic Speed Control
To Set A Desired Speed To Resume Speed
Turn the Electronic Speed Control ON. When the vehicle To resume a previously set speed, push the RES (+)
has reached the desired speed, press the SET (-) button button and release. Resume can be used at any speed
and release. Release the accelerator and the vehicle will above 20 mph (32 km/h).
operate at the selected speed.
To Vary The Speed Setting
NOTE: The vehicle should be traveling at a steady When the Electronic Speed Control is set, you can in-
speed and on level ground before pressing the SET crease speed by pushing the RES (+) button. If the button
button. is continually pressed, the set speed will continue to
increase until the button is released, then the new set
To Deactivate
speed will be established.
A soft tap on the brake pedal, pushing the CANCEL
button, or normal brake pressure while slowing the Pressing the RES (+) button once will result in a 1 mph
vehicle will deactivate Electronic Speed Control without (2 km/h) increase in set speed. Each subsequent tap of
erasing the set speed memory. Pressing the ON/OFF the button results in an increase of 1 mph (2 km/h).
button or turning the ignition switch OFF erases the set
To decrease speed while the Electronic Speed Control is
speed memory.
set, push the SET (-) button. If the button is continually
held in the SET (-) position, the set speed will continue to
decrease until the button is released. Release the button On steep hills, a greater speed loss or gain may occur so
when the desired speed is reached, and the new set speed it may be preferable to drive without Electronic Speed
will be established. Control.
Pressing the SET (-) button once will result in a 1 mph
WARNING!
(2 km/h) decrease in set speed. Each subsequent tap of
the button results in a decrease of 1 mph (2 km/h). Electronic Speed Control can be dangerous where the 3
system cannot maintain a constant speed. Your ve-
To Accelerate For Passing
hicle could go too fast for the conditions, and you
Press the accelerator as you would normally. When the
could lose control and have an accident. Do not use
pedal is released, the vehicle will return to the set speed.
Electronic Speed Control in heavy traffic or on roads
Using Electronic Speed Control On Hills that are winding, icy, snow-covered or slippery.
The transmission may downshift on hills to maintain the
vehicle set speed. PARKSENSE REAR PARK ASSIST IF
NOTE: The Electronic Speed Control system maintains EQUIPPED
speed up and down hills. A slight speed change on The ParkSense Rear Park Assist system provides visual
moderate hills is normal. and audible indications of the distance between the rear
fascia and a detected obstacle when backing up, e.g.
during a parking maneuver. Refer to ParkSense System
Usage Precautions for limitations of this system and ParkSense Sensors
recommendations. The four ParkSense sensors, located in the rear fascia/
bumper, monitor the area behind the vehicle that is
ParkSense will retain the last system state (enabled or
within the sensors field of view. The sensors can detect
disabled) from the last ignition cycle when the ignition is
obstacles from approximately 12 in (30 cm) up to 79 in
changed to the ON/RUN position.
(200 cm) from the rear fascia/bumper in the horizontal
ParkSense can be active only when the shift lever is in direction, depending on the location, type and orienta-
REVERSE. If ParkSense is enabled at this shift lever tion of the obstacle.
position, the system will remain active until the vehicle
ParkSense Warning Display
speed is increased to approximately 11 mph (18 km/h) or
The ParkSense Warning screen will only be displayed if
above. The system will become active again if the vehicle
Sound and Display is selected from the Customer- Pro-
speed is decreased to speeds less than approximately
grammable Features section of the Electronic Vehicle
10 mph (16 km/h).
Information Center (EVIC). Refer to Electronic Vehicle
Information Center (EVIC)/Personal Settings (Customer-
Programmable Features) in Understanding Your In-
strument Panel for further information.
The ParkSense Warning Display is located in the Instru- ParkSense Display
ment clusters EVIC display. It provides both visual and When the vehicle is in REVERSE, the warning display
audible warnings to indicate the distance between the will turn ON indicating the system status.
rear fascia/bumper and the detected obstacle.
Park Assist System ON

ParkSense Warning Display
Park Assist System OFF Slow Tone

The system will indicate a detected obstacle by showing
three solid arcs and will produce a one-half second tone.
As the vehicle moves closer to the object the EVIC
display will show fewer arcs and the sound tone will
change from slow, to fast, to continuous.
Fast Tone Continuous Tone

The vehicle is close to the obstacle when the EVIC display
shows one flashing arc and sounds a continuous tone.
The following chart shows the warning alert operation
when the system is detecting an obstacle:
WARNING ALERTS
Rear Distance Greater than 79-39 in 39-25 in 25-12 in Less than
(in/cm) 79 in (200 cm) (200-100 cm) (100-65 cm) (65-30 cm) 12 in (30 cm)
Audible Alert None Single 1/2 Slow Fast Continuous
Chime Second Tone
Display Message Park Assist Warning Object Warning Object Warning Object Warning Object
System ON Detected Detected Detected Detected
Arcs None 3 Solid 3 Slow 2 Slow 1 Slow
(Continuous) Flashing Flashing Flashing
Radio Mute No Yes Yes Yes Yes
NOTE: ParkSense will MUTE the radio, if on, when (EVIC)/Personal Settings (Customer-Programmable Fea-
the system is sounding an audio tone. tures) in Understanding Your Instrument Panel for
further information.
Enabling/Disabling ParkSense
ParkSense can be enabled and disabled through the When ParkSense is disabled, the instrument cluster will
Customer-Programmable Features section of the EVIC. display the PARK ASSIST SYSTEM OFF message for
The available choices are: OFF, Sound Only, or Sound and approximately five seconds. Refer to Electronic Vehicle
Display. Refer to Electronic Vehicle Information Center Information Center (EVIC) in Understanding Your
Instrument Panel for further information. When the
shift lever is moved to REVERSE and the system is If CLEAN PARK ASSIST SENSORS appears in the
disabled, the EVIC will display the PARK ASSIST SYS- EVIC after making sure the rear fascia/bumper is free
TEM OFF message for as long as the vehicle is in from snow, ice, mud, dirt or other obstruction, see your
REVERSE. authorized dealer.
Service The ParkSense Rear Park Assist System If SERVICE PARK ASSIST SYSTEM appears in the
When the ParkSense Rear Park Assist System is mal- EVIC, see your authorized dealer. 3
functioning, the instrument cluster will actuate a single
Cleaning The ParkSense System
chime, once per ignition cycle, and it will display the
Clean the ParkSense sensors with water, car wash soap
CLEAN PARK ASSIST SENSORS or the SERVICE
and a soft cloth. Do not use rough or hard cloths. Do not
PARK ASSIST SYSTEM message. Refer to Electronic
scratch or poke the sensors. Otherwise, you could dam-
Vehicle Information Center (EVIC) in Understanding
age the sensors.
Your Instrument Panel for further information. When
the shift lever is moved to REVERSE and the system has ParkSense System Usage Precautions
detected a faulted condition, the EVIC will display the
NOTE:
CLEAN PARK ASSIST SENSORS or the SERVICE
Ensure that the rear bumper is free of snow, ice, mud,
PARK ASSIST SYSTEM message for as long as the
dirt and debris to keep the ParkSense system operat-
vehicle is in REVERSE. Under this condition, ParkSense
ing properly.
will not operate.
Jackhammers, large trucks, and other vibrations could properly. The ParkSense system might not detect an
affect the performance of ParkSense. obstacle behind the fascia/bumper, or it could provide
a false indication that an obstacle is behind the fascia/
When you turn ParkSense off, the instrument cluster
bumper.
will display PARK ASSIST SYSTEM OFF. Further-
more, once you turn ParkSense off, it remains off Objects such as bicycle carriers, trailer hitches, etc.,
until you turn it on again, even if you cycle the ignition must not be placed within 12 in (30 cm) from the rear
key. fascia/bumper while driving the vehicle. Failure to do
so can result in the system misinterpreting a close
When you move the shift lever to the REVERSE
object as a sensor problem, causing the SERVICE
position and ParkSense is turned off, the EVIC will
PARK ASSIST SYSTEM message to be displayed in
display PARK ASSIST SYSTEM OFF message for as
the EVIC.
long as the vehicle is in REVERSE.
On vehicles equipped with a tailgate, ParkSense
ParkSense, when on, will MUTE the radio when it is
should be disabled when the tailgate is in the lowered
sounding a tone.
or open position and the vehicle is in REVERSE. A
Clean the ParkSense sensors regularly, taking care lowered tailgate could provide a false indication that
not to scratch or damage them. The sensors must not an obstacle is behind the vehicle.
be covered with ice, snow, slush, mud, dirt or debris.
Failure to do so can result in the system not working
CAUTION! WARNING!
ParkSense is only a parking aid and it is unable Drivers must be careful when backing up even
to recognize every obstacle, including small ob- when using the ParkSense Rear Park Assist Sys-
stacles. Parking curbs might be temporarily de- tem. Always check carefully behind your vehicle,
tected or not detected at all. Obstacles located look behind you, and be sure to check for pedes- 3
above or below the sensors will not be detected trians, animals, other vehicles, obstructions, and
when they are in close proximity. blind spots before backing up. You are responsible
The vehicle must be driven slowly when using for safety and must continue to pay attention to
ParkSense in order to be able to stop in time your surroundings. Failure to do so can result in
when an obstacle is detected. It is recommended serious injury or death.
that the driver looks over his/her shoulder when (Continued)
using ParkSense.
PARKVIEW REAR BACK UP CAMERA IF
EQUIPPED
Before using the ParkSense Rear Park Assist Your vehicle may be equipped with the ParkView Rear
System, it is strongly recommended that the ball Back Up Camera that allows you to see an on-screen
mount and hitch ball assembly is disconnected image of the rear surroundings of your vehicle whenever
from the vehicle when the vehicle is not used for the shift lever is put into REVERSE. The image will be
towing. Failure to do so can result in injury or displayed on the Navigation/Multimedia radio display
damage to vehicles or obstacles because the hitch screen along with a caution note to check entire sur-
ball will be much closer to the obstacle than the roundings across the top of the screen. After five sec-
rear fascia when the warning display turns on the onds this note will disappear. The ParkView camera is
single flashing arc and sounds the continuous located on the rear of the vehicle above the rear License
tone. Also, the sensors could detect the ball mount plate.
and hitch ball assembly, depending on its size and
shape, giving a false indication that an obstacle is When the vehicle is shifted out of REVERSE, the rear
behind the vehicle. camera mode is exited and the navigation or audio screen
appears again.
When displayed, static grid lines will illustrate the width that will help indicate the distance to the rear of the
of the vehicle while a dashed center-line will indicate the vehicle. The following table shows the approximate
center of the vehicle to assist with aligning to a hitch/ distances for each zone:
receiver. The static grid lines will show separate zones
Zone Distance to the rear of the vehicle
Red 0 - 1 ft (0 - 30 cm) 3
Yellow 1 ft - 3 ft (30 cm - 1 m)
Green 3 ft or greater (1 m or greater)
WARNING! CAUTION! (Continued)

Drivers must be careful when backing up even when To avoid vehicle damage, the vehicle must be
using the ParkView Rear Back Up Camera. Always driven slowly when using ParkView to be able to
check carefully behind your vehicle, and be sure to stop in time when an obstacle is seen. It is recom-
check for pedestrians, animals, other vehicles, ob- mended that the driver look frequently over his/
structions, or blind spots before backing up. You are her shoulder when using ParkView.
responsible for the safety of your surroundings and
must continue to pay attention while backing up. NOTE: If snow, ice, mud, or any foreign substance
Failure to do so can result in serious injury or death. builds up on the camera lens, clean the lens, rinse with
water, and dry with a soft cloth. Do not cover the lens.
CAUTION! Turning ParkView On Or Off With

Navigation/Multimedia Radio
To avoid vehicle damage, ParkView should only
be used as a parking aid. The camera is unable to 1. Press the menu hard-key.
view every obstacle or object in your drive path. 2. Select system setup soft-key.
(Continued) 3. Press the camera setup soft-key.
4. Enable or disable the rear camera feature by selecting illuminates the instrument panel cupholders, two swiv-
enable rear camera in reverse soft-key. eling LED lights, flip-down sunglass storage, conversa-
tion mirror, optional power sliding door switches and an
5. Press the save soft-key.
optional power liftgate switch.
Turning ParkView On Or Off Without
NOTE: Premium sunroof console models include all of
Navigation/Multimedia Radio 3
above except sunglass storage.
1. Press the menu hard-key.
2. Select system setup soft-key.
3. Enable or disable the rear camera feature by selecting
enable rear camera in reverse soft-key.
OVERHEAD CONSOLES
Front Overhead Console
Two versions of the overhead console are available. The
base front overhead console model featured fixed incan-
descent courtesy/reading lights, flip-down sunglass stor-
age and conversation mirror. The premium front over-
head console model features a LED focused light that Overhead Console
Courtesy/Interior Lighting Sunglass Storage (Non-Sunroof Only)
At the forward end of the console are two courtesy lights At the front of the overhead console, a compartment is
(standard dome light has two buttons). The lights turn on provided for the storage of two pairs of sunglasses.
when a front door, a sliding door or the liftgate is opened.
From the closed position, press the door latch to open the
If your vehicle is equipped with Remote Keyless Entry
compartment.
(RKE) the lights will also turn on when the UNLOCK
button on the RKE transmitter is pressed.
The courtesy lights also function as reading lights. Press
in on each lens to turn these lights on while inside the
vehicle. Press a second time to turn each light off. You
may adjust the direction of these lights by pressing the
outside ring, which is identified with four directional
arrows (LED lamps only).
The area around the instrument panel cupholders is also
illuminated from a light in the overhead console (pre-
mium console only). This light is turned on when the
headlight switch is on, and will adjust in brightness when
Over Door Latch
the dimmer control is rotated up or down.
The door will slowly rotate to the full open position.
Full Open Position Conversation Mirror Position

From this position, the door can be fully closed or, by NOTE: From the conversation mirror position, the
rotating upward about 3/4 of the way and releasing, door can only be closed.
positioned for conversation mirror use.
To return to the full open position, the door must first be
closed and then opened by pressing the latch again to
release.
Rear Courtesy/Reading Lights If Equipped
The overhead console has two sets of courtesy lights. The
lights turn on when a front door, a sliding door or the
liftgate is opened. If your vehicle is equipped with
Remote Keyless Entry (RKE) the lights will also turn on
when the UNLOCK button on the RKE transmitter is
pressed.
The courtesy lights also function as reading lights. Press
in on each lens to turn these lights on while inside the
vehicle. Press the lens a second time to turn each light off.
You may adjust the direction of these lights by pressing
the outside ring, which is identified with four directional Reading Lights
arrows.
Rear Overhead Consoles If Equipped
The rear overhead storage system is available in two
versions: with or without sunroof.
An additional LED at the front of the rear console shines
down on the front foot-well area while in courtesy mode,
for added convenience.
Rear Console Halo Lighting
The rear overhead console has recessed halo lighting
around the perimeter of the console base. This feature
provides additional lighting options while traveling and
is controlled by the headlight switch. Refer to Lights/
Halo Lights If Equipped in Understanding the 3
Features Of Your Vehicle for further information.
GARAGE DOOR OPENER IF EQUIPPED

HomeLink replaces up to three hand-held transmitters
that operate devices such as garage door openers, motor-
ized gates, lighting or home security systems. The
Overhead Compartment Features HomeLink unit is powered by your vehicles 12 Volt
1 DVD 1 5 Storage battery.
2 Rear HVAC 6 DVD 1
3 Interior Lights 7 Interior Lights
4 Storage 8 Halo Lighting
1
If equipped, otherwise storage.
The HomeLink buttons, located on either the overhead
console, headliner or sunvisor, designate the three differ-
ent HomeLink channels. The HomeLink indicator is
located above the center button.
HomeLink Buttons/Sunvisor/Headliner
NOTE: HomeLink is disabled when the Vehicle Secu-
rity Alarm is active.
HomeLink Buttons/Overhead Consoles

Before You Begin Programming HomeLink position and press and hold the two outside HomeLink
Be sure that your vehicle is parked outside of the garage buttons (I and III) for up 20 seconds or until the red
before you begin programming. indicator flashes.
For more efficient programming and accurate transmis- NOTE:
sion of the radio-frequency signal it is recommended that Erasing all channels should only be performed when
a new battery be placed in the hand-held transmitter of programming HomeLink for the first time. Do not 3
the device that is being programmed to the HomeLink erase channels when programming additional buttons.
system.
If you have any problems, or require assistance, please
Erase all channels before you begin programming. To call toll-free 18003553515 or, on the Internet at
erase the channels place the ignition in the ON/RUN www.HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manu-
factured after 1995. These garage door openers can be
identified by the LEARN or TRAIN button located
where the hanging antenna is attached to the garage door
opener. It is NOT the button that is normally used to
open and close the door. The name and color of the
button may vary by manufacturer.
Training The Garage Door Opener

1 Door Opener
2 Training Button
1. Turn the ignition switch to the ON/RUN position.

2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Simultaneously press and hold both the Homelink NOTE: You have 30 seconds in which to initiate the next
button you want to program and the hand-held transmit- step after the LEARN button has been pressed.
ter button.
6. Return to the vehicle and press the programmed
4. Continue to hold both buttons and observe the indi- HomeLink button twice (holding the button for two
cator light. The Homelink indicator will flash slowly seconds each time). If the garage door opener/device
and then rapidly after Homelink has received the fre- activates, programming is complete. 3
quency signal from the hand-held transmitter. Release
NOTE: If the garage door opener/device does not
both buttons after the indicator light changes from slow
activate, press the button a third time (for two seconds) to
to rapid.
complete the training.
5. At the garage door opener motor (in the garage),
To program the remaining two HomeLink buttons,
locate the LEARN or TRAINING button. This can
repeat each step for each remaining button. DO NOT
usually be found where the hanging antenna wire is
erase the channels.
attached to the garage door opener/device motor. Firmly
press and release the LEARN or TRAINING button. Reprogramming A Single HomeLink Button
On some garage door openers/devices there may be a To reprogram a channel that has been previously trained,
light that blinks when the garage door opener/device is follow these steps:
in the LEARN/TRAIN mode.
2. Press and hold the desired HomeLink button until 4. Continue to hold both buttons and observe the indi-
the indicator light begins to flash after 20 seconds. Do not cator light. The Homelink indicator will flash slowly
release the button. and then rapidly after Homelink has received the fre-
quency signal from the hand-held transmitter. Release
3. Without releasing the button proceed with Program-
both buttons after the indicator light changes from slow
ming A Rolling Code Step 2 and follow all remaining
to rapid.
steps.
5. Press and hold the programmed HomeLink button
Programming A Non-Rolling Code
and observe the indicator light.
For programming Garage Door Openers manufactured
before 1995. If the indicator light stays on constantly, program-
ming is complete and the garage door/device
should activate when the HomeLink button is
2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm) pressed.
away from the HomeLink button you wish to program
To program the two remaining HomeLink buttons,
while keeping the HomeLink indicator light in view.
repeat each step for each remaining button. DO
3. Simultaneously press and hold both the Homelink NOT erase the channels.
button you want to program and the hand-held transmit-
ter button.
Reprogramming A Single HomeLink Button to pick up the signal during programming. Similar to this
To reprogram a channel that has been previously trained, Canadian law, some U.S. gate operators are designed to
follow these steps: time-out in the same manner.
1. Turn the ignition switch to the ON/RUN position. It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage
2. Press and hold the desired HomeLink button until 3
door or gate motor.
the indicator light begins to flash after 20 seconds. Do not
release the button. 1. Turn the ignition switch to the ON/RUN position.
3. Without releasing the button proceed with Program- 2. Place the hand-held transmitter 1 to 3 in (3 to 8 cm)
ming A Non-Rolling Code Step 2 and follow all remain- away from the HomeLink button you wish to program
ing steps. while keeping the HomeLink indicator light in view.
Canadian/Gate Operator Programming 3. Continue to press and hold the HomeLink button,
For programming transmitters in Canada/United States while you press and release (cycle), your hand-held
that require the transmitter signals to time-out after transmitter every two seconds until HomeLink has
several seconds of transmission. successfully accepted the frequency signal. The indicator
light will flash slowly and then rapidly when fully
Canadian radio frequency laws require transmitter sig-
trained.
nals to time-out (or quit) after several seconds of trans-
mission which may not be long enough for HomeLink
4. Watch for the HomeLink indicator to change flash Reprogramming A Single HomeLink Button
rates. When it changes, it is programmed. It may take up To reprogram a channel that has been previously trained,
to 30 seconds or longer in rare cases. The garage door follow these steps:
may open and close while you are programming.
5. Press and hold the programmed HomeLink button
2. Press and hold the desired HomeLink button until
and observe the indicator light.
the indicator light begins to flash after 20 seconds. Do not
If the indicator light stays on constantly, program- release the button.
ming is complete and the garage door/device
3. Without releasing the button proceed with
should activate when the HomeLink button is
Canadian/Gate Operator Programming Step 2 and
pressed.
follow all remaining steps.
To program the two remaining HomeLink buttons,
Using HomeLink
repeat each step for each remaining button. DO
To operate, press and release the programmed
NOT erase the channels.
HomeLink button. Activation will now occur for the
If you unplugged the garage door opener/device for programmed device (i.e., garage door opener, gate opera-
programming, plug it back in at this time. tor, security system, entry door lock, home/office light-
ing, etc.,). The hand-held transmitter of the device may
also be used at any time.
Security Troubleshooting Tips
It is advised to erase all channels before you sell or turn If you are having trouble programming HomeLink, here
in your vehicle. are some of the most common solutions:
To do this, press and hold the two outside buttons for Replace the battery in the original hand-held transmit-
20 seconds until the red indicator flashes. Note that all ter.
channels will be erased. Individual channels cannot be 3
Press the LEARN button on the Garage Door Opener
erased.
to complete the training for a Rolling Code.
The HomeLink Universal Transceiver is disabled when
Did you unplug the device for programming and
the Vehicle Security Alarm is active.
remember to plug it back in?
If you have any problems, or require assistance, please
call toll-free 18003553515 or, on the Internet at
www.HomeLink.com for information or assistance.
General Information
WARNING!
This device complies with FCC rules Part 15 and Industry
Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following
while you are programming the universal trans- two conditions:
ceiver. Do not program the transceiver if people,
1. This device may not cause harmful interference.
pets or other objects are in the path of the door or
gate. Only use this transceiver with a garage door 2. This device must accept any interference that may be
opener that has a stop and reverse feature as received including interference that may cause undesired
required by Federal safety standards. This includes operation.
most garage door opener models manufactured
NOTE:
after 1982. Do not use a garage door opener without
The transmitter has been tested and it complies with
these safety features. Call toll-free 18003553515
FCC and IC rules. Changes or modifications not
or, on the Internet at www.HomeLink.com for
expressly approved by the party responsible for com-
safety information or assistance.
pliance could void the users authority to operate the
Vehicle exhaust contains carbon monoxide, a dan- device.
gerous gas. Do not run your vehicle in the garage
while programming the transceiver. Exhaust gas The term IC before the certification/registration num-
can cause serious injury or death. ber only signifies that Industry Canada technical
specifications were met.
POWER SUNROOF IF EQUIPPED
WARNING!
The power sunroof switch is located between the sun
visors on the overhead console. Never leave children in a vehicle with the key in
the ignition switch. Occupants, particularly unat-
tended children, can become entrapped by the
power sunroof while operating the power sunroof 3
switch. Such entrapment may result in serious
injury or death.
In a collision, there is greater risk of being thrown
from a vehicle with an open sunroof. You could
also be seriously injured or killed. Always fasten
your seat belt properly and make sure all passen-
gers are properly secured.
Do not allow small children to operate the sun-
roof. Never allow your fingers, other body parts, or
Power Sunroof Switch any object, to project through the sunroof opening.
Injury may result.
Opening Sunroof Express automatically. This is called Express Close. During
Press the switch rearward and release it within one-half Express Close operation, any movement of the sunroof
second and the sunroof will open automatically from any switch will stop the sunroof.
position. The sunroof will open fully and stop automati-
Closing Sunroof Manual Mode
cally. This is called Express Open. During Express
To close the sunroof, press and hold the switch in the
Open operation, any movement of the sunroof switch
forward position. Any release of the switch will stop the
will stop the sunroof.
movement and the sunroof will remain in a partially
Opening The Sunroof Manual Mode closed condition until the switch is pushed and held
To open the sunroof, press and hold the switch rearward forward again.
to full open. Any release of the switch will stop the
Pinch Protect Feature
movement and the sunroof will remain in a partially
This feature will detect an obstruction in the opening of
opened condition until the switch is pushed and held
the sunroof during Express Close operation. If an ob-
rearward again.
struction is detected, the sunroof will automatically re-
Closing Sunroof Express tract. Remove the obstruction if this occurs. Next, press
Press the switch forward and release it within one-half the switch forward and release to Express Close.
second, and the sunroof will close automatically from
any position. The sunroof will close fully and then stop
NOTE: If three consecutive sunroof close attempts re- Sunshade Operation
sult in Pinch Protect reversals, the fourth close attempt The sunshade can be opened manually. However, the
will be a Manual Close movement with Pinch Protect sunshade will open automatically as the sunroof opens.
disabled.
NOTE: The sunshade cannot be closed if the sunroof is
Pinch Protect Override open.
If a known obstruction (ice, debris, etc.) prevents closing 3
Wind Buffeting
the sunroof, press the switch forward and hold for two
Wind buffeting can be described as the perception of
seconds after the reversal occurs. This allows the sunroof
pressure on the ears or a helicopter-type sound in the
to move toward the closed position.
ears. Your vehicle may exhibit wind buffeting with the
NOTE: Pinch protection is disabled while the switch is windows down, or the sunroof (if equipped) is in certain
pressed. open or partially open positions. This is a normal occur-
rence and can be minimized. If the buffeting occurs with
Venting Sunroof Express
the rear windows open, open the front and rear windows
Press and release the Vent button, and the sunroof will
together to minimize the buffeting. If the buffeting occurs
open to the vent position. This is called Express Vent,
with the sunroof open, adjust the sunroof opening to
and will occur regardless of sunroof position. During
minimize the buffeting or open any window.
Express Vent operation, any movement of the switch will
stop the sunroof.
Sunroof Maintenance Sunroof Fully Closed
Use only a non-abrasive cleaner and a soft cloth to clean Press the switch forward and release to ensure that the
the glass panel. sunroof is fully closed.
Ignition Off Operation ELECTRICAL POWER OUTLETS IF EQUIPPED
For vehicles not equipped with the Electronic Vehicle Two 12 Volt (13 Amp) power outlets are located on the
Information Center (EVIC), the power sunroof switch lower instrument panel, below the open storage bin. The
will remain active for 45 seconds after the ignition switch
driver-side power outlet is controlled by the ignition
is turned to the LOCK position. Opening either front switch and the passenger-side power outlet is connected
door will cancel this feature. directly to the battery. The driver-side power outlet will
NOTE: For vehicles equipped with the EVIC, the power also operate a conventional cigar lighter unit (if equipped
sunroof switch will remain active for up to approxi- with an optional Smokers Package).
mately ten minutes after the ignition switch is turned to
the LOCK position. Opening either front door will cancel
this feature.
CAUTION!
Do not exceed the maximum power of 160 Watts
(13 Amps) at 12 Volts. If the 160 Watt (13 Amp)
power rating is exceeded the fuse protecting the
system will need to be replaced. 3
Power outlets are designed for accessory plugs
only. Do not insert any other object in the power
outlets as this will damage the outlet and blow the
fuse. Improper use of the power outlet can cause
damage not covered by your New Vehicle Limited
Warranty.
Instrument Panel Outlets
NOTE: To ensure proper operation a MOPAR cigar
knob and element must be used.
One outlet in the removable floor console (if equipped) On vehicles equipped with the Super Console the power
shares a fuse with the lower outlet in the instrument outlets are located under the retractable cover. To access
panel and is also connected to the battery. Do not exceed the power outlets push down on the cover and slide it
a maximum power of 160 Watts (13 Amps) shared toward the instrument panel.
between the lower panel outlet and the removable floor
console outlet.
Super Console Outlets
Removable Console Outlet

The outlet in the rear quarter panel near the liftgate and
the upper outlet in the instrument panel are both con-
trolled by the ignition switch. Each of these outlets can
support 160 Watts (13 Amps). Do not exceed 160 Watts
(13 Amps) for each of these outlets.
The power outlets include tethered caps, labeled with a 3
key or battery symbol indicating the power source. The
power outlet, located on the lower instrument panel, is
powered directly from the battery. Items plugged into
this power outlet may discharge the battery and/or
prevent the engine from starting.
Power Outlet Fuses
1 M7 Fuse 20 A Yellow Power Outlet Center Seat (Opt) or
with Console Rear
2 M6 Fuse 20 A Yellow Cigar Lighter Instrument Panel or
with Console Front
3 M36 Fuse 20 A Yellow Power Outlet Instrument Panel or
with Console Center
WARNING! CAUTION! (Continued)

To avoid serious injury or death: Accessories that draw higher power (i.e., coolers,
Only devices designed for use in this type of vacuum cleaners, lights, etc.), will degrade the
outlet should be inserted into any 12 Volt outlet. battery even more quickly. Only use these inter-
Do not touch with wet hands. mittently and with greater caution.
Close the lid when not in use and while driving After the use of high power draw accessories, or
the vehicle. long periods of the vehicle not being started (with
If this outlet is mishandled, it may cause an accessories still plugged in), the vehicle must be
electric shock and failure. driven a sufficient length of time to allow the
alternator to recharge the vehicles battery.
Power outlets are designed for accessory plugs
CAUTION!
only. Do not hang any type of accessory or acces-
Many accessories that can be plugged in draw sory bracket from the plug. Improper use of the
power from the vehicles battery, even when not in power outlet can cause damage.
use (i.e., cellular phones, etc.). Eventually, if
plugged in long enough, the vehicles battery will
discharge sufficiently to degrade battery life
and/or prevent the engine from starting.
(Continued)
POWER INVERTER IF EQUIPPED The power inverter switch is located on the instrument
A 110 Volt, 150 Watt inverter outlet (if equipped) converts panel below the climate controls.
DC current to AC current, and is located on the left rear
To turn on the power outlet, press the switch once. Press
trim panel immediately behind the second row left
the switch a second time to turn the power outlet off.
passenger seat.
This outlet can power cellular phones, electronics and 3
other low power devices requiring power up to 150
Watts. Certain high-end video games, such as Playsta-
tion3 and XBox360 will exceed this power limit, as will
most power tools.
The power inverter is designed with built-in overload
protection. If the power rating of 150 Watts is exceeded,
the power inverter will automatically shut down. Once
the electrical device has been removed from the outlet the
inverter should automatically reset. If the power rating
exceeds approximately 170 Watts, the power inverter
may have to be reset manually. To reset the inverter
Power Inverter Outlet
manually press the power inverter button OFF and ON.
To avoid overloading the circuit, check the power ratings
on electrical devices prior to using the inverter.
CUPHOLDERS
There are cupholders located throughout the interior. All
liners are removable for cleaning. Pull the flexible liner
from the cupholder drawer or tray starting at one edge
for easy removal. Refer to Cleaning The Instrument
Panel Cupholders in Maintaining Your Vehicle for
Instrument Panel Cupholders
The instrument panel cupholders are located in a pull-out
Front Cupholders
drawer just above the lower storage bin.
Pull the drawer out firmly until it stops, and place the
container to be held in either one of the cupholder wells.
The cupholders are designed to accommodate a wide
variety of container types and sizes. Press down on the
container to engage the cupholder retention features.
Super Console If Equipped For rear passengers two cupholders are located in the
On models equipped with the Super Console, there are pull-out drawer, located in the back of the Super Console.
two cupholders located in the center of the console. Pull the drawer out to the first position to use the
cupholders.
Super Console Cupholders

Rear Cupholders
Premium Console Cupholders If Equipped Interior Bottle Holders
On models equipped with premium center consoles, There are four bottle holders located in the interior. One
there are four cupholders located on the top of the bottle holder is molded into each front interior door trim
console. panels, and one bottle holder is molded into each side
sliding interior door trim panel. Each holder accommo-
dates up to a 20 oz (.6 L) plastic bottle.
WARNING!
If containers of hot liquid are placed in the bottle
holder, they can spill when the door is closed, burn-
ing the occupants. Be careful when closing the doors
to avoid injury.
Premium Console Cupholders

Smokers Package Kit If Equipped
With the optional authorized dealer-installed Smokers
Package Kit, a removable ash receiver is inserted into one
of the two cupholders in the center front instrument
panel. To install the ash receiver, align the receiver so the
thumb grip on the lid is facing rearward. Press the ash 3
receiver into either of the cup wells to secure. Pull
upward on the ash receiver to remove for cleaning
and/or storage.
The left rear trim panel cupholder is designed to accom-
modate a second ash receiver, if desired.
Interior Bottle Holder
Two outboard mesh pockets are on intermediate seating.
The mesh pockets are flexible enough to hold juice boxes,
toys, games or MP3 players, etc.
STORAGE Upper Glove Compartment
To open the upper compartment, press in on the button,
Glove Compartments
located on the left side of the upper door. The door will
Upper and lower glove compartments are located on the
automatically open.
passenger side of the instrument panel.
Upper Compartment
Upper and Lower Glove Compartments
To close the compartment door, push downward on the
doors surface to latch the door closed.
Lower Glove Compartment NOTE: The lower compartment is equipped with a lock
To open the lower compartment pull out on the release that is part of the compartment handle.
handle.
Door Trim Panel Storage
Front Door Storage
Both interior front door panels have multiple pockets for 3
storage.
Lower Compartment
Driver Seatback Storage If Equipped Umbrella Holder
The drivers seatback has a primary storage pocket on all An umbrella holder has been conveniently molded into
models and an optional secondary mesh pocket. the left front door entry scuff molding.
Drivers Seatback Storage Umbrella Holder

1 Bag Holder
2 Standard Pocket
3 Mesh Pocket
Second Row Seat Storage Bins If Equipped
The seat storage bins are located on the floor in front of
the second row seats. The area below the covers can be
used for storage when the second row seat is in the
upright position.
Pull up on the storage bin latch to open the cover. Slide 3
the storage bin locking mechanism to the Lock position
to allow greater access to the storage bin.
Storage Bin
CAUTION!
NOTE: The storage bin cover must be locked and flat
to avoid damage from contact with the front seat
tracks, which have minimal clearance to the cover.

In a collision, serious injury could result if the seat Do not allow children to have access to the second
storage bin covers are not properly latched. row seat storage bins. Once in the storage bin,
DO NOT drive the vehicle with the storage bin young children may not be able to escape. If
covers open. trapped in the storage bin, children can die from
suffocation or heat stroke.
Keep the storage bin covers closed and latched
while the vehicle is in motion. In a collision, serious injury could result if the seat
storage bin covers are not properly latched.
DO NOT use a storage bin latch as a tie down.
Do not drive the vehicle with the storage bin
Storage Bin Safety Warning covers open. Keep the storage bin covers closed
Carefully follow these warnings to help prevent personal and latched while the vehicle is in motion.
injury or damage to your vehicle: Do not operate the storage bin covers while the
vehicle is in motion.
WARNING! Do not use a storage bin latch as a tie down.
Always close the storage bin covers when your

vehicle is unattended.
(Continued)
CAUTION!
The storage bin cover must be flat and locked to
avoid damage from contact with the front seat tracks,
which have minimal clearance to the cover.
3
Seat Storage Bin Cover Emergency Release Lever
As a security measure, your vehicle may be built with a
Storage Bin Cover Emergency Release is built into the
storage bin cover latching mechanism.
Storage Bin Cover Emergency Release Lever

NOTE: In the event of an individual being locked inside
the storage bin, the storage bin cover can be opened from
inside of the bin by pushing on the glow-in-the-dark
lever attached to the storage bin cover latching
mechanism.
Coat Hooks
Coat hooks are located along the headliner for the second
and third row seating positions. The coat hook load limit
is 10 lbs (4.5 kg). Exceeding the recommended load limit
can cause the coat hooks to break or disengage from the
vehicle.
Cargo Area Storage
The liftgate sill plate has a raised line with the statement
Load To This Line. This line indicates how far rearward
cargo can be placed without interfering with liftgate
closing.
Rear Cargo Area Loading Limit
NOTE: With all rear seats stowed or removed, 4 x 8 foot
sheets of building material will fit on the vehicle floor
with the liftgate closed. The front seats must be moved
slightly forward of the rearmost position.
CONSOLE FEATURES Four cupholders accept up to extra large size beverage
There are three consoles available: Basic, Premium and cups or 20 oz (.6 L) plastic bottles. Cupholders are
Super. dishwasher safe for cleaning.
The cupholders are removable to access a large storage
WARNING!
bin.
Do not operate this vehicle with a console compart- 3
The basic console is removable from the vehicle for
ment lid in the open position. Cellular phones, music
additional floor space by removing the cap and clip at
players, and other handheld electronic devices
the console base.
should be stowed while driving. Use of these devices
while driving can cause an accident due to distrac- To Remove The Basic Floor Console
tion, resulting in death or injury.
1. Remove the front anchor cup plug and clip.
Basic Console 2. Slide the console base forward while lifting slightly to
Basic Console features consist of the following: clear the rear load floor hook.
The basic console profile allows vehicle occupants to 3. Remove the console.
easily pass through the first row to the second.
To Reinstall The Basic Floor Console
WARNING!
1. Position the console at a slight angle (front slightly
In an accident, serious injury could result if the
higher than the rear).
removable floor console is not properly installed.
2. Slide the console rearward into the floor bracket/ Always be sure the removable floor console is fully
hook. latched.
3. Align the console until the front anchor cup plug hole
Premium Console If Equipped
is centered on the winch hole.
The three-compartment console with sliding storage bin,
4. Reinstall the clip first and then while pushing down- sliding upper tray with storage and large console storage
ward on the console with slight pressure, reinstall the bin offers multiple configurations.
cover plug.
Four cupholders with dishwasher safe liners for clean-
5. Pull up on the console to be sure it is firmly latched. ing. The cupholders can accept plastic bottles, large
cups or mugs with handles.
Top tray storage
Upper storage bin can hold nine regular or 18 thin CDs
or other items
Large console center storage will store headphones for Position 1 shows the console closed with four cupholders
the available rear DVD entertainment system or other and a convenient storage tray.
items
12 Volt DC power outlet provides continuous power
inside the console for cell phones or other electronics.
3
Rear occupant accessible
Multiple adjustments
Removable from vehicle for additional floor space.
The top and center console sections slide forward and
rearward to provide added user comfort. A one-piece cup
holder insert for both cavities can easily be removed for
cleaning. The cupholders will also accommodate large
Console Position 1
size cups and 20 oz (.6 L) bottles.
Position 2 shows the raised storage tray revealing a large Dual Storage Bins
storage area below. Position 3 shows the top portion of the console in a
rearward position. This is accomplished by lifting the
upper most latch at the front of the console. This provides
easy access to the storage area below and provides two of
the four cupholders for the second row passengers.
Console Position 2
Console Position 3
Position 4 shows the complete console in its rearmost To Remove The Premium Floor Console
position. Again, lifting second latch handle at the front of
1. Pull up on the bottom release handle in the front of the
the console, allows complete access to a lower storage bin
console.
and provides additional cupholders for rear passengers.
2. Lift the rear of the console up several inches/
centimeters. 3
3. Pull rearward to disengage from floor and remove
console.
To reinstall the console:
1. Position the console at a slight angle (rear slightly
higher than the front).
2. Slide the console forward into the floor bracket.
3. Rotate the rear of the console down until it is resting
on the floor bracket.
Console Position 4
4. Push down on the rear of the console until it is seated
in the rear floor bracket.
5. Pull up on the console to be sure it is firmly latched.
WARNING!
In an accident, serious injury could result if the
removable floor console is not properly installed.
Always be sure the removable floor console is fully
latched.
Super Console If Equipped

The Super Console contains multiple storage areas, front
lower pass through, top forward bin, top rearward bin
and rear pull out drawer. Front Lower Pass Through
The super console contains a pass through storage area The super console tambour doors are opened by pushing
accessible for both the driver and front passenger. down on the finger tabs and sliding the door. The front
tambour door slides forward, the rear tambour door
slides rearward.
NOTE: The front cupholder light ring and pass through
lighting is controlled by a dimming switch located on the
instrument panel, refer to Lights in Understanding
The Features Of Your Vehicle for further information.
Located in the back of the super console is a storage
drawer and cupholders for the rear passengers. 3
Super Console
1 Front Sliding Tambour Door
2 Cupholder Light Ring
3 Rear Sliding Tambour Door
Rear Drawer Storage

CARGO AREA FEATURES
Rechargeable Flashlight
The rechargeable flashlight is mounted on the right side
of the cargo area. The flashlight snaps out of the bezel
when needed. The flashlight features two bright LED
light bulbs and is powered by a lithium battery that
recharges when snapped back into place and the vehicle
is either running or the key is in the accessory position.
Press in on the flashlight to release it.
Press And Release

To operate the flashlight, press the switch once for high,
twice for low, and a third time to return to off.
REAR WINDOW FEATURES
Rear Window Defroster
The rear window defroster button is located on the
climate control (Mode) knob. Press this button to
turn on the rear window defroster and the heated outside
mirrors (if equipped). An indicator in the button will 3
illuminate when the rear window defroster is on. The
rear window defroster automatically turns off after ap-
proximately 10 minutes. For an additional five minutes of
operation, press the button a second time.
NOTE:
Three-Press Switch You can turn off the heated mirror feature at anytime
by pressing the rear window defroster switch a second
time.
To prevent excessive battery drain, use the rear win-
dow defroster only when the engine is operating.
A hydraulic pump contained within the shock absorbers
CAUTION!
raises the rear of the vehicle to the correct height. It takes
Failure to follow these cautions can cause damage to approximately 1 mile (1.6 km) of driving for the leveling
the heating elements: to complete depending on road surface conditions.
Use care when washing the inside of the rear If the leveled vehicle is not moved for approximately
window. Do not use abrasive window cleaners on 15 hours, the leveling system will bleed itself down. The
the interior surface of the window. Use a soft cloth vehicle must be driven to reset the system.
and a mild washing solution, wiping parallel to
the heating elements. Labels can be peeled off ROOF LUGGAGE RACK IF EQUIPPED
after soaking with warm water. The crossbars on your vehicle are delivered stowed
Do not use scrapers, sharp instruments, or abra- within the roof rack side rails. If adding cargo, deploy the
sive window cleaners on the interior surface of the crossbars. Distribute cargo weight evenly on the roof rack
window. crossbars, to maximum of 150 lbs (68 kg). The roof rack
Keep all objects a safe distance from the window. does not increase the total load carrying capacity of the
vehicle. Be sure the total load of cargo inside the vehicle
REAR LOAD-LEVELING SYSTEM IF EQUIPPED plus that on the external rack does not exceed the
The automatic load-leveling system will provide a level maximum vehicle load capacity.
riding vehicle under most passenger and cargo loading
conditions.
The crossbars and side rails are designed to carry weight
on vehicles equipped with a luggage rack. The load must
not exceed 150 lbs (68 kg), and should be uniformly
distributed over the luggage rack crossbars.
NOTE:
Crossbars are error-proofed and cannot be deployed or 3
stowed in the incorrect positions.
To help control wind noise, stow the crossbars in the
side rails when they are not in use.
Crossbar Stowed In Side Rail

Deploying the Crossbars
CAUTION!
To deploy the crossbars, completely loosen the thumb
screws at both ends of the crossbar and lift the crossbar Use care when removing and handling the crossbars
from its stowed position in the side rail. Repeat with to prevent damage to the vehicle.
crossbar on the opposite side.
Bend the crossbar supports at each end, taking care to
keep hand clear of pivoting joint. Slide the thumb screw
down.
Loosening Crossbars
Stowed Position Deployed Position

Then, position the crossbars across the roof.
NOTE: The crossbars are identical and can be placed in Make sure the directional arrows on the crossbars align
any two of the three deploy positions. with the directional arrows on the side rails. Set the
crossbars into the deployed positions.
Deploy Positions Choose Two Of Three

Crossbar To Side Rail Installation
Once the crossbars are set into position, tighten the
thumb screws completely.
NOTE: Load should always be secured to crossbars
first, with rail tie down loops used as additional securing
points if needed. Tie loops are intended as supplemen-
tary tie down points only. Do not use ratcheting mecha-
nisms with the tie loops.
3
Tightening Crossbar
Stowing the Crossbars
Reverse the procedure to stow the crossbars, again,
taking care to keep hand clear of pivoting joint. Crossbars
are identical and can be stowed in either rail nest. Once
the crossbars are stowed, tighten the thumb screws Rail Tie Loops
completely.
CAUTION! CAUTION! (Continued)

Check deployed crossbars frequently and re- Long loads which extend over the windshield,
tighten thumb screws as necessary. such as wood panels or surfboards, or loads with
To avoid damage to the roof rack and vehicle, do large frontal area should be secured to both the
not exceed the maximum roof rack load capacity of front and rear of the vehicle.
150 lbs (68 kg). Always distribute heavy loads as Travel at reduced speeds and turn corners care-
evenly as possible and secure the load appropri- fully when carrying large or heavy loads on the
ately. roof rack. Wind forces, due to natural causes or
To prevent damage to the roof of your vehicle, DO nearby truck traffic, can add sudden upward lift to
NOT carry any loads on the roof rack without the a load. This is especially true on large flat loads
crossbars deployed. and may result in damage to the cargo or your
vehicle.
The load should be secured and placed on top of
the crossbars, not directly on the roof. If it is
necessary to place the load on the roof, place a
blanket or other protective layer between the load
and the roof surface.
(Continued)
WARNING!
Cargo must be securely tied before driving your
vehicle. Improperly secured loads can fly off the
vehicle, particularly at high speeds, resulting in per-
sonal injury or property damage. Follow the Roof 3
Rack Cautions when carrying cargo on your roof
rack.
SUN SCREENS IF EQUIPPED

Sun screens are available for second and third row
seating windows. The screens store in the sill trim panels,
Sun Screen Retracted
and the tops of the windows are equipped with hooks
that the sun screens attach to when pulled out.
Gently pull up on the tab to raise the sun screen. To lower the sun screen, gently lift the tab upward to
Continue pulling the sun screen until the tab is near the disengage the hooks, and feed the screen back into the
top of the window. base sill.
Once the screen is completely to the top of the window,
extend the top bar of the sun screen over the two hooks
attached to the top of the window.
Sun Screen Extended

UNDERSTANDING YOUR INSTRUMENT PANEL
CONTENTS
Instrument Panel Features . . . . . . . . . . . . . . . 283 Trip Info . . . . . . . . . . . . . . . . . . . . . . . . . . 310
Instrument Cluster Base . . . . . . . . . . . . . . . 284 Tire Psi . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
4
Instrument Cluster Premium . . . . . . . . . . . 285 Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Instrument Cluster Descriptions . . . . . . . . . . . 286 Vehicle Info
(Customer Information Features) . . . . . . . . . 311
Electronic Vehicle Information Center
(EVIC) If Equipped . . . . . . . . . . . . . . . . . . . 300 Messages . . . . . . . . . . . . . . . . . . . . . . . . . . 311
Electronic Vehicle Information Center Compass / Temperature Display . . . . . . . . . 312
(EVIC) Displays . . . . . . . . . . . . . . . . . . . . . 302
Customer-Programmable Features
Fuel Economy . . . . . . . . . . . . . . . . . . . . . . 308 (System Setup) . . . . . . . . . . . . . . . . . . . . . . 314
Vehicle Speed . . . . . . . . . . . . . . . . . . . . . . . 309
280 UNDERSTANDING YOUR INSTRUMENT PANEL
Media Center 730N/430/430N (RHR/RER/ Media Center 130 With Satellite Radio
RBZ/RHB) CD/DVD/HDD/NAV If (Sales Code RES+RSC). . . . . . . . . . . . . . . . . . . 330
Equipped . . . . . . . . . . . . . . . . . . . . . . . . . . . . 320
Operating Instructions Radio Mode . . . . . 330
Operating Instructions (Voice Command
Operation Instructions CD Mode For CD
System) If Equipped . . . . . . . . . . . . . . . . 320
And MP3 Audio Play . . . . . . . . . . . . . . . . . 336
Operating Instructions
Notes On Playing MP3 Files . . . . . . . . . . . . 338
(Uconnect Phone) If Equipped . . . . . . . 320
List Button (CD Mode For MP3 Play) . . . . . . 341
Media Center 130 (Sales Code RES) . . . . . . . . . 321
Info Button (CD Mode For MP3 Play) . . . . . . 341
Operating Instructions Radio Mode . . . . . 321
Uconnect Multimedia (Satellite Radio)
Operation Instructions CD Mode For CD
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 342
And MP3 Audio Play . . . . . . . . . . . . . . . . . 324
Operating Instructions
Notes On Playing MP3 Files . . . . . . . . . . . . 326
(Uconnect Phone) If Equipped . . . . . . . 346
Operation Instructions - Auxiliary Mode . . . . 329
iPod/USB/MP3 Control If Equipped . . . . . 346
Connecting The iPod Or External USB
Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . 347
UNDERSTANDING YOUR INSTRUMENT PANEL 281
Using This Feature . . . . . . . . . . . . . . . . . . . 347 Play A DVD Using The
Touch-Screen Radio . . . . . . . . . . . . . . . . . . . 359
Controlling The iPod Or External USB
Device Using Radio Buttons . . . . . . . . . . . . . 348 Play A DVD Using The VES Player
(If Equipped) . . . . . . . . . . . . . . . . . . . . . . . 362
Play Mode . . . . . . . . . . . . . . . . . . . . . . . . . 348
Listen To An Audio Source While A Video Is
List Or Browse Mode . . . . . . . . . . . . . . . . . 350
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . 364
Bluetooth Streaming Audio (BTSA) . . . . . . . . 352 4
Third Row Swivel Screen (If Equipped) . . . . . 367
Uconnect Multimedia Video Entertainment
Important Notes For Dual Video Screen
System (VES) If Equipped . . . . . . . . . . . . 353
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 368
Getting Started . . . . . . . . . . . . . . . . . . . . . . 353
Remote Control . . . . . . . . . . . . . . . . . . . . . 368
Play Video Games . . . . . . . . . . . . . . . . . . . . 354
Remote Control Storage . . . . . . . . . . . . . . . . 371
Listen To An Audio Source On Channel 2
Locking The Remote Control . . . . . . . . . . . . 371
While A Video Is Playing On Channel 1 . . . . 357
Replacing The Remote Control Batteries . . . . 372
Dual Video Screen . . . . . . . . . . . . . . . . . . . 359
Headphones Operation . . . . . . . . . . . . . . . . 372
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 Rear Manual Climate Control
If Equipped . . . . . . . . . . . . . . . . . . . . . . . . 397
Replacing The Headphone Batteries . . . . . . . 374
Automatic Temperature Control
Unwired Stereo Headphone Lifetime
(ATC) If Equipped . . . . . . . . . . . . . . . . . 400
Limited Warranty . . . . . . . . . . . . . . . . . . . . 374
Summer Operation . . . . . . . . . . . . . . . . . . . 411
System Information . . . . . . . . . . . . . . . . . . . 376
Winter Operation . . . . . . . . . . . . . . . . . . . . 412
Steering Wheel Audio
Controls If Equipped. . . . . . . . . . . . . . . . . . 389 Vacation/Storage . . . . . . . . . . . . . . . . . . . . 412
Radio Operation . . . . . . . . . . . . . . . . . . . . . 390 Window Fogging . . . . . . . . . . . . . . . . . . . . 412
CD Player . . . . . . . . . . . . . . . . . . . . . . . . . 390 Outside Air Intake . . . . . . . . . . . . . . . . . . . 412
CD/DVD Disc Maintenance . . . . . . . . . . . . . . 391 Operating Tips . . . . . . . . . . . . . . . . . . . . . . 413
Radio Operation And Mobile Phones . . . . . . . 391 A/C Air Filter . . . . . . . . . . . . . . . . . . . . . . 413
Climate Controls . . . . . . . . . . . . . . . . . . . . . . 392
Manual Heating And Air Conditioning
System If Equipped . . . . . . . . . . . . . . . . . 392
INSTRUMENT PANEL FEATURES
1 Air Vents 5 Upper Glove Compartment 9 Storage Bin 13 Hood Release

2 Instrument Cluster 6 Lower Glove Compartment 10 Cup Holders 14 Dimmer Switch
3 Shift Lever 7 Climate Controls 11 Switch Bank 15 Headlight Switch
4 Radio 8 DVD If Equipped 12 Ignition Switch
INSTRUMENT CLUSTER BASE
INSTRUMENT CLUSTER PREMIUM
4
INSTRUMENT CLUSTER DESCRIPTIONS 4. Turn Signal Indicators
The arrow will flash with the exterior turn signal
1. Tachometer
when the turn signal lever is operated.
The red segments indicate the maximum permissible
engine revolutions per minute (RPM x 1000) for each gear If the vehicle is driven more than 1 mile (1.6 km) with
range. Before reaching the red area, ease up on the either turn signal on, a continuous chime will sound to
accelerator. alert you to turn the signal off. If either indicator flashes
at a rapid rate, check for a defective outside light bulb.
2. Front Fog Light Indicator If Equipped
This indicator will illuminate when the front fog 5. High Beam Indicator
lights are on. This indicator shows that the high beam head-
lights are on. Push the multifunction lever forward
3. Park/Headlight ON Indicator If Equipped
to switch the headlights to high beam, and pull toward
This indicator will illuminate when the park
yourself (normal position) to return to low beam.
lights or headlights are turned on.
6. Odometer Display / Electronic Vehicle Information
Center (EVIC) Display If Equipped
Odometer Display / Trip Odometer Display
The odometer display shows the total distance the ve-
hicle has been driven.
U.S. Federal regulations require that upon transfer of Message Display Area
vehicle ownership, the seller certify to the purchaser the When the appropriate conditions exist, the following
correct mileage that the vehicle has been driven. If your odometer messages will display:
odometer needs to be repaired or serviced, the repair
technician should leave the odometer reading the same door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Door Ajar
as it was before the repair or service. If s/he cannot do so, gATE . . . . . . . . . . . . . . . . . . . . . . . . . . . Liftgate Ajar
then the odometer must be set at zero, and a sticker must LoW tirE. . . . . . . . . . . . . . . . . . . . . Low Tire Pressure
be placed in the door jamb stating what the mileage was gASCAP . . . . . . . . . . . . . . . . . . . . . . . Fuel Cap Fault 4
before the repair or service. It is a good idea for you to noFUSE . . . . . . . . . . . . . . . . . . . . . . . . . . Fuse Fault
make a record of the odometer reading before the repair/ CHAngE OIL . . . . . . . . . . . . . . . Oil Change Required
service, so that you can be sure that it is properly reset, or LoCOOL . . . . . . . . . . . . . . . . . . . . . . . . Low Coolant
that the door jamb sticker is accurate if the odometer
NOTE: Some of the above warnings will be displayed in
must be reset at zero.
the Electronic Vehicle Information Center Display Area
This also displays Trip A and Trip B, DTE, MPG or located in the instrument cluster.
L/100km, OAT (Outside Air Temperature) information to
Refer to Electronic Vehicle Information Center (EVIC)
Base Cluster, use STEP and RESET button (on steering
Display If Equipped for further information.
wheel) to access or reset the display. For further informa-
tion refer to Compass Mini-Trip Computer.
LoW tirE CHAngE OIL
When the appropriate condition exists, the odometer Your vehicle is equipped with an engine oil change
display will toggle between LoW and tirE for three indicator system. The CHAngE OIL message will flash in
cycles. the instrument cluster odometer for approximately
12 seconds, after a single chime has sounded, to indicate
gASCAP
the next scheduled oil change interval. The engine oil
If the vehicle diagnostic system determines that the fuel
change indicator system is duty cycle-based, which
filler cap is loose, improperly installed, or damaged, a
means the engine oil change interval may fluctuate
gASCAP message will display in the odometer display
dependent upon your personal driving style.
area. Tighten the fuel filler cap properly and press the
STEP button on the steering wheel to turn off the Unless reset, this message will continue to display each
message. If the problem continues, the message will time you turn the ignition switch to the ON/RUN
appear the next time the vehicle is started. position. To turn off the message temporarily, press and
release the STEP button on the steering wheel. To reset
noFUSE
the oil change indicator system (after performing the
If the vehicle diagnostic system determines that the Igni-
scheduled maintenance), perform the following steps.
tion Off Draw (IOD) fuse is improperly installed, or
damaged, a noFUSE message will display in the odom- 1. Turn the ignition switch to the ON/RUN position (do
eter display area. For further information on fuses and fuse not start the engine).
locations refer to Fuses in Maintaining Your Vehicle.
2. Fully depress the accelerator pedal, slowly, three times If the ABS light remains on or turns on while driving, it
within 10 seconds. indicates that the Anti-Lock portion of the brake system
is not functioning and that service is required. However,
3. Turn the ignition switch to the OFF/LOCK position.
the conventional brake system will continue to operate
NOTE: If the indicator message illuminates when you normally if the BRAKE warning light is not on.
start the engine, the oil change indicator system did not
If the ABS light is on, the brake system should be serviced
reset. If necessary, repeat these steps.
as soon as possible to restore the benefits of Anti-Lock
Electronic Vehicle Information Center (EVIC) brakes. If the ABS light does not turn on when the 4
Display If Equipped ignition switch is turned to the ON/RUN position, have
The Electronic Vehicle Information Center (EVIC) fea- the light inspected by an authorized dealer.
tures a driver-interactive display that is located in the
8. Tire Pressure Monitoring Telltale Light If
instrument cluster. For further information, refer to
Equipped
Electronic Vehicle Information Center (EVIC).
Each tire, including the spare (if provided),
7. Anti-Lock Brake (ABS) Light should be checked monthly when cold and
This light monitors the Anti-Lock Brake System inflated to the inflation pressure recommended
(ABS). The light will turn on when the ignition by the vehicle manufacturer on the vehicle
switch is turned to the ON/RUN position and placard or tire inflation pressure label. (If your vehicle
may stay on for as long as four seconds. has tires of a different size than the size indicated on the
vehicle placard or tire inflation pressure label, you should maintain correct tire pressure, even if under-inflation has
determine the proper tire inflation pressure for those not reached the level to trigger illumination of the TPMS
tires.) low tire pressure telltale.
As an added safety feature, your vehicle has been Your vehicle has also been equipped with a TPMS
equipped with a Tire Pressure Monitoring System malfunction indicator to indicate when the system is not
(TPMS) that illuminates a low tire pressure telltale when operating properly. The TPMS malfunction indicator is
one or more of your tires is significantly under-inflated. combined with the low tire pressure telltale. When the
Accordingly, when the low tire pressure telltale illumi- system detects a malfunction, the telltale will flash for
nates, you should stop and check your tires as soon as approximately one minute and then remain continuously
possible, and inflate them to the proper pressure. Driving illuminated. This sequence will continue upon subse-
on a significantly under-inflated tire causes the tire to quent vehicle start-ups as long as the malfunction exists.
overheat and can lead to tire failure. Under-inflation alsoWhen the malfunction indicator is illuminated, the sys-
reduces fuel efficiency and tire tread life, and may affecttem may not be able to detect or signal low tire pressure
the vehicles handling and stopping ability. as intended. TPMS malfunctions may occur for a variety
of reasons, including the installation of replacement or
Please note that the TPMS is not a substitute for proper
alternate tires or wheels on the vehicle that prevent the
tire maintenance, and it is the drivers responsibility to
TPMS from functioning properly. Always check the
TPMS malfunction telltale after replacing one or more
tires or wheels on your vehicle, to ensure that the 9. Malfunction Indicator Light (MIL)
replacement or alternate tires and wheels allow the TPMS The Malfunction Indicator Light (MIL) is part of
to continue to function properly. an onboard diagnostic system, called OBD, that
monitors engine and automatic transmission con-
CAUTION! trol systems. The light will illuminate when the key is in
the ON/RUN position, before engine start. If the bulb
The TPMS has been optimized for the original
does not come on when turning the key from OFF to
equipment tires and wheels. TPMS pressures and
warning have been established for the tire size
ON/RUN, have the condition checked promptly. 4
equipped on your vehicle. Undesirable system opera- Certain conditions, such as a loose or missing gas cap,
tion or sensor damage may result when using re- poor fuel quality, etc., may illuminate the MIL after
placement equipment that is not of the same size, engine start. The vehicle should be serviced if the light
type, and/or style. Aftermarket wheels can cause stays on through several of your typical driving cycles. In
sensor damage. Do not use tire sealant from a can or most situations, the vehicle will drive normally and will
balance beads if your vehicle is equipped with a not require towing.
TPMS, as damage to the sensors may result.
10. Electronic Stability Control (ESC) Activation/
CAUTION!
Malfunction Indicator Light If Equipped
Prolonged driving with the MIL on could cause The ESC Activation/Malfunction Indicator
damage to the engine control system. It also could Light in the instrument cluster will come on
affect fuel economy and drivability. If the MIL is when the ignition switch is turned to the
flashing, severe catalytic converter damage and ON/RUN position. It should go out with the
power loss will soon occur. Immediate service is engine running. If the ESC Activation/Malfunction In-
required. dicator Light comes on continuously with the engine
running, a malfunction has been detected in the ESC
system. If this light remains on after several ignition
WARNING!
cycles, and the vehicle has been driven several miles
A malfunctioning catalytic converter, as referenced (kilometers) at speeds greater than 30 mph (48 km/h), see
above, can reach higher temperatures than in normal your authorized dealer as soon as possible to have the
operating conditions. This can cause a fire if you problem diagnosed and corrected.
drive slowly or park over flammable substances such NOTE:
as dry plants, wood, cardboard, etc. This could result The ESC Off Indicator Light and the ESC
in death or serious injury to the driver, occupants or Activation/Malfunction Indicator Light come on mo-
others. mentarily each time the ignition switch is turned to
ON/RUN.
Each time the ignition is turned to ON/RUN, the ESC 13. Fuel Door Reminder
system will be ON, even if it was turned off previously. The arrow in this symbol is a reminder that the
Fuel Filler Door is located on the left side of the
The ESC system will make buzzing or clicking sounds
vehicle.
when it is active. This is normal; the sounds will stop
when ESC becomes inactive following the maneuver
14. Fuel Gauge
that caused the ESC activation.
The pointer shows the level of fuel in the fuel tank when
11. Electronic Stability Control (ESC) OFF Indicator the ignition switch is in the ON/RUN position. 4
Light If Equipped
15. Air Bag Warning Light
This light indicates the Electronic Stability Con-
This light will turn on for four to eight seconds
trol (ESC) is off.
as a bulb check when the ignition switch is first
turned to ON/RUN. If the light is either not on
during starting, stays on, or turns on while
12. Speedometer
driving, have the system inspected at an authorized
Indicates vehicle speed.
dealer as soon as possible. Refer to Occupant Restraints
in Things To Know Before Starting Your Vehicle for
16. Shift Lever Indicator 18. Brake Warning Light
The Shift Lever Indicator is self-contained within the This light monitors various brake functions,
instrument cluster. It displays the gear position of the including brake fluid level and parking brake
automatic transmission. application. If the brake light turns on it may
indicate that the parking brake is applied, that
NOTE:
the brake fluid level is low, or that there is a problem with
You must apply the brakes before shifting from PARK.
the anti-lock brake system reservoir.
The highest available transmission gear is displayed in
If the light remains on when the parking brake has been
the lower right corner of the Electronic Vehicle Infor-
disengaged, and the fluid level is at the full mark on the
mation Center (EVIC) whenever the Electronic Range
master cylinder reservoir, it indicates a possible brake
Select (ERS) feature is active. Use the +/- selector on
hydraulic system malfunction or that a problem with the
the shift lever to activate ERS. Refer to Automatic
Brake Booster has been detected by the Anti-Lock Brake
Transmission in Starting And Operating for further
System (ABS) / Electronic Stability Control (ESC) system.
information.
In this case, the light will remain on until the condition
17. Vehicle Security Light If Equipped has been corrected. If the problem is related to the brake
This light will flash at a fast rate for approxi- booster, the ABS pump will run when applying the brake
mately 15 seconds, when the vehicle security and a brake pedal pulsation may be felt during each stop.
alarm is arming, and then will flash slowly
until the vehicle is disarmed.
The dual brake system provides a reserve braking capac-
WARNING!
ity in the event of a failure to a portion of the hydraulic
system. A leak in either half of the dual brake system is Driving a vehicle with the red brake light on is
indicated by the Brake Warning Light, which will turn on dangerous. Part of the brake system may have failed.
when the brake fluid level in the master cylinder has It will take longer to stop the vehicle. You could have
dropped below a specified level. a collision. Have the vehicle checked immediately.
The light will remain on until the cause is corrected.
Vehicles equipped with the Anti-Lock Brake System 4
NOTE: The light may flash momentarily during sharp (ABS), are also equipped with Electronic Brake Force
cornering maneuvers, which change fluid level condi- Distribution (EBD). In the event of an EBD failure, the
tions. The vehicle should have service performed, and Brake Warning Light will turn on along with the ABS
the brake fluid level checked. Light. Immediate repair to the ABS system is required.
If brake failure is indicated, immediate repair is neces- Operation of the Brake Warning Light can be checked by
sary. turning the ignition switch from the OFF position to the
ON/RUN position. The light should illuminate for ap-
proximately two seconds. The light should then turn off
unless the parking brake is applied or a brake fault is
detected. If the light does not illuminate, have the light
inspected by an authorized dealer.
The light also will turn on when the parking brake is 20. Temperature Gauge
applied with the ignition switch in the ON/RUN posi- The temperature gauge shows engine coolant tempera-
tion. ture. Any reading within the normal range indicates that
the engine cooling system is operating satisfactorily.
NOTE: This light shows only that the parking brake is
applied. It does not show the degree of brake application. The gauge pointer will likely indicate a higher tempera-
ture when driving in hot weather, up mountain grades,
19. Seat Belt Reminder Light
or when towing a trailer. It should not be allowed to
When the ignition switch is first turned to ON/
exceed the upper limits of the normal operating range.
RUN, this light will turn on for four to eight
seconds as a bulb check. During the bulb check, if
CAUTION!
the driver or front passengers seat belt is unbuckled, a
chime will sound. After the bulb check or when driving, Driving with a hot engine cooling system could
if the drivers seat belt remains unbuckled, the Seat Belt damage your vehicle. If the temperature gauge reads
Reminder Light will illuminate and the chime will sound. H pull over and stop the vehicle. Idle the vehicle
Refer to Occupant Restraints in Things To Know with the air conditioner turned off until the pointer
Before Starting Your Vehicle for further information. drops back into the normal range. If the pointer
remains on the H and you hear continuous chimes,
turn the engine off immediately and call an autho-
rized dealership for service.
while driving, turn off some of the vehicles non-essential
WARNING!
electrical devices or increase engine speed (if at idle). If
A hot engine cooling system is dangerous. You or the charging system light remains on, it means that the
others could be badly burned by steam or boiling vehicle is experiencing a problem with the charging
coolant. You may want to call an authorized dealer- system. Obtain SERVICE IMMEDIATELY. See an autho-
ship for service if your vehicle overheats. If you rized dealer.
decide to look under the hood yourself, see Main-
If jump starting is required, refer to Jump Starting
taining Your Vehicle. Follow the warnings under the
Procedures in What To Do In Emergencies. 4
Cooling System Pressure Cap paragraph.
23. Oil Pressure Warning Light
21. Low Fuel Light This light indicates low engine oil pressure. The
When the fuel level reaches approximately 2.0 gal light should turn on momentarily when the engine
(7.8 L) this light will turn on, and remain on until is started. If the light turns on while driving, stop the
fuel is added. vehicle and shut off the engine as soon as possible. A
chime will sound for four minutes when this light turns
22. Charging System Light
on.
This light shows the status of the electrical charg-
ing system. The light should come on when the Do not operate the vehicle until the cause is corrected.
ignition switch is first turned to ON/RUN and remain on This light does not indicate how much oil is in the engine.
briefly as a bulb check. If the light stays on or comes on The engine oil level must be checked under the hood.
24. Engine Temperature Warning Light 25. Electronic Throttle Control (ETC) Light
This light warns of an overheated engine condi- This light informs you of a problem with the
tion. As engine coolant temperatures rise and the Electronic Throttle Control (ETC) system. The
gauge approaches H , this indicator will illuminate light will come on when the ignition is first
and a single chime will sound after reaching a set turned to ON/RUN and remain on briefly as a
threshold. Further overheating will cause the tempera- bulb check. If the light does not come on during starting,
ture gauge to pass H , the indicator will continuously have the system checked by an authorized dealer.
flash and a continuous chime will occur until the engine
If a problem is detected, the light will come on while the
is allowed to cool.
engine is running. Cycle the ignition key when the
If the light turns on while driving, safely pull over and vehicle has completely stopped and the shift lever is
stop the vehicle. If the A/C system is on, turn it off. Also, placed in the PARK position, the light should turn off.
shift the transmission into NEUTRAL and idle the ve-
If the light remains lit with the engine running, your
hicle. If the temperature reading does not return to
vehicle will usually be drivable; however, see an autho-
normal, turn the engine off immediately and call for
rized dealer for service as soon as possible. If the light is
service. Refer to If Your Engine Overheats in What To
flashing when the engine is running, immediate service is
Do In Emergencies for further information.
required and you may experience reduced performance,
an elevated/rough idle or engine stall and your vehicle
may require towing.
26. Transmission Temperature Warning Light
CAUTION!
During sustained high speed driving or trailer
towing up long grades on hot days, the auto- Continuous driving with the Transmission Tempera-
matic transmission oil may become too hot. ture Warning Light illuminated will eventually cause
When the transmission overheat warning light severe transmission damage or transmission failure.
turns on, you will experience reduced vehicle perfor-
mance until the automatic transmission cools down.
WARNING!
Once the transmission has cooled down and the light 4
turns off, you may continue to drive normally. If the high If the Transmission Temperature Warning Light is
speed is maintained, the overheating will continue to illuminated and you continue operating the vehicle,
occur. in some circumstances you could cause the fluid to
If the overheating continues, it may become necessary to boil over, come in contact with hot engine or exhaust
stop the vehicle and run the engine at idle with the components and cause a fire.
transmission in NEUTRAL until the light turns off.
ELECTRONIC VEHICLE INFORMATION CENTER This system conveniently allows the driver to select a
(EVIC) IF EQUIPPED variety of useful information by pressing the switches
The Electronic Vehicle Information Center (EVIC) fea- mounted on the steering wheel. The EVIC consists of the
tures a driver-interactive display that is located in the following:
instrument cluster.
Radio Information
Fuel Economy
Vehicle Speed
Trip Info
Tire PSI
Vehicle Info
Messages
Units
System Setup (Personal Settings)
Electronic Vehicle Information Center (EVIC)
Turn Menu Off
The system allows the driver to select information by UP Button
pressing the following buttons mounted on the steering Press and release the UP button to scroll up-
wheel: ward through the main menus (Fuel Economy,
Vehicle Info, Tire PSI, Cruise, Messages, Units,
System Setup) and sub-menus.
DOWN Button
Press and release the DOWN button to scroll
downward through the main menus and sub- 4
menus.
SELECT Button
The SELECT button allows access to informa-
tion in EVIC submenus, selects some feature
settings, and resets some EVIC features. The
EVIC prompts the driver when the SELECT
EVIC Steering Wheel Buttons
button can be used by displaying the right arrow graphic.
BACK Button Remote start active Key to Run
Press the BACK button to scroll back to a
Wrong Key
previous menu or sub-menu.
Damaged Key
Key not programmed
Electronic Vehicle Information Center (EVIC)
Displays Vehicle Not in Park
When the appropriate conditions exist, the EVIC displays
Press Brake Pedal and Push Button to Start
the following messages:
Door(s) Ajar (with a single chime, if vehicle is in
Key in ignition
motion)
Ignition or Accessory On
Liftgate Ajar (chime will sound when vehicle starts
Remote start aborted Door ajar moving)
Remote start aborted Hood ajar Low Tire Pressure
Remote start aborted L/Gate ajar Service TPM System (refer to Tire Pressure Monitor-
ing System in Starting And Operating)
Remote start aborted Fuel low
Premium TPM Service Graphic Display
Remote start disabled Start Vehicle to Reset
Turn Signal On Blind Spot System Not Available This message is
displayed to indicate the Blind Spot Monitor (BSM)
RKE Battery Low
system is temporarily unavailable due to sensor block-
LOW WASHER FLUID age, electronic interference, or other temporary con-
ditions. When this message is displayed both outside
Oil Change Required
rear view icons will be illuminated. If electronic inter-
Left Front Turn Signal Light Out ference is present, the BSM system will illuminate the
Left Rear Turn Signal Light Out
icon only on the side of interference as long as 4
interference is present.
Right Front Turn Signal Light Out
Service Blind Spot System This message is dis-
Right Rear Turn Signal Light Out played to indicate the Blind Spot Monitor (BSM)
system is permanently unavailable. The driver will
Park Assist Disabled
receive an EVIC message and the BSM display warn-
Service Park Assist System ing in both mirrors will be permanently illuminated. If
this message is present see an authorized dealer.
Personal Settings Not Available Vehicle Not In Park
Blind Spot System Off This message is displayed
when the ignition is turned to ON to indicate the Blind
Spot System has been turned off.
EVIC White Telltale Lights Electronic Speed Control SET
This area will show reconfigurable white caution tell- This light will turn on when the electronic
tales. These telltales include: speed control is SET. For further information,
refer to Electronic Speed Control in Under-
Electronic Range Select (ERS) Status
standing The Features Of Your Vehicle.
The shift lever status 5,4,3,2,1 are displayed indicating
the shift lever position. Telltales 5,4,3,2,1 indicate the EVIC Amber Telltale Lights
Electronic Range Select (ERS) feature has been engaged This area will show reconfigurable amber caution tell-
and the gear selected is displayed. For further informa- tales. These telltales include:
tion on ERS, refer to Starting And Operating
Low Fuel Light
Electronic Speed Control Ready When the fuel level reaches approximately 3.0 gal
This light will turn on when the electronic (11.0 L) this light will turn on, and remain on until
speed control is ready. For further information, fuel is added.
refer to Electronic Speed Control in Under-
Loose Gascap Indicator
standing The Features Of Your Vehicle.
If the vehicle diagnostic system determines
that the fuel filler cap is loose, improperly
installed, or damaged, a loose gascap indicator
will display in the telltale display area. Tighten
the fuel filler cap properly and press the SELECT button
to turn off the message. If the problem continues, the Oil Pressure Warning Light
message will appear the next time the vehicle is started. This light indicates low engine oil pressure. The
light should turn on momentarily when the engine
A loose, improperly installed, or damaged fuel filler cap
is started. If the light turns on while driving, stop the
may also turn on the Malfunction Indicator Light (MIL).
vehicle and shut off the engine as soon as possible. A
Windshield Washer Fluid Low Indicator chime will sound for four minutes when this light turns
This light will turn on to indicate the wind- on.
shield washer fluid is low.
Do not operate the vehicle until the cause is corrected. 4
This light does not show how much oil is in the engine.
The engine oil level must be checked under the hood.
EVIC Red Telltale Lights
This area will show reconfigurable red telltales. These Charging System Light
telltales include: This light shows the status of the electrical charg-
ing system. The light should come on when the
Door Ajar
ignition switch is first turned ON and remain on briefly
This light will turn on to indicate that one or
as a bulb check. If the light stays on or comes on while
more doors may be ajar.
driving, turn off some of the vehicles non-essential
electrical devices or increase engine speed (if at idle). If
the charging system light remains on, it means that the
vehicle is experiencing a problem with the charging If the light remains lit with the engine running, your
system. Obtain SERVICE IMMEDIATELY. See an autho- vehicle will usually be drivable. However, see an autho-
rized dealer. rized dealer for service as soon as possible. If the light is
flashing when the engine is running, immediate service is
If jump starting is required, refer to Jump Starting
required. You may experience reduced performance, an
Procedures in What To Do In Emergencies.
elevated/rough idle or engine stall and your vehicle may
Electronic Throttle Control (ETC) Light require towing.
This light informs you of a problem with the
Engine Temperature Warning Light
Electronic Throttle Control (ETC) system. The
This light warns of an overheated engine condi-
light will come on when the ignition is first
tion. As temperatures rise and the gauge ap-
turned ON and remain on briefly as a bulb
proaches H, this indicator will illuminate and a
check. If the light does not come on during starting, have
single chime will sound after reaching a set threshold.
the system checked by an authorized dealer.
Further overheating will cause the temperature gauge to
If a problem is detected, the light will come on while the pass H, the indicator will continuously flash and a
engine is running. Cycle the ignition key when the continuous chime will occur until the engine is allowed
vehicle has completely stopped and the shift lever is to cool.
placed in the PARK position. The light should turn off.
If the light turns on while driving, safely pull over and
stop the vehicle. If the A/C system is on, turn it off. Also,
shift the transmission into NEUTRAL and idle the ve-
WARNING!
hicle. If the temperature reading does not return to
normal, turn the engine off immediately and call for If the Transmission Temperature Warning Light is
service. Refer to If Your Engine Overheats in What To illuminated and you continue operating the vehicle,
Do In Emergencies for more information. in some circumstances you could cause the fluid to
boil over, come in contact with hot engine or exhaust
Transmission Temperature Warning Light
components and cause a fire.
This light indicates that the transmission fluid
temperature is running hot. This may occur 4
Oil Change Required
with severe usage, such as trailer towing. If this
Your vehicle is equipped with an engine oil change
light turns on, safely pull over and stop the
indicator system. The Oil Change Required message will
vehicle. Then, shift the transmission into NEUTRAL and
flash in the EVIC display for approximately 10 seconds,
run the engine at idle or faster until the light turns off.
after a single chime has sounded, to indicate the next
scheduled oil change interval. The engine oil change
CAUTION!
indicator system is duty-cycle based, which means the
Continuous driving with the Transmission Tempera- engine oil change interval may fluctuate dependent upon
ture Warning Light illuminated will eventually cause your personal driving style.
severe transmission damage or transmission failure.
Unless reset, this message will continue to display each Fuel Economy
time you turn the ignition switch to the ON/RUN Press and release the UP or DOWN button until Fuel
position. To turn off the message temporarily, press and Economy displays highlighted in the EVIC and press
release the Menu button. To reset the oil change indicator the SELECT button. The following Fuel Economy func-
system (after performing the scheduled maintenance), tions display in the EVIC:
perform the following steps.
Average Fuel Economy (AVG)
1. Turn the ignition switch to the ON position (do not
Distance To Empty (DTE)
start the engine.)
Miles Per Gallon (MPG)
2. Fully depress the accelerator pedal, slowly, three times
within 10 seconds. Average Fuel Economy
This display shows the average fuel economy since the
3. Turn the ignition switch to the OFF/LOCK position.
last reset. The Average Fuel Economy can be reset by
NOTE: If the indicator message illuminates when you following the prompt in the EVIC to use the SELECT
start the engine, the oil change indicator system did not button. When the fuel economy is reset, the display will
reset. If necessary, repeat these steps. read zero for two seconds. Then, the history informa-
tion will be erased, and the averaging will continue from
the last fuel average reading before the reset.
NOTE: Significant changes in driving style or vehicle
loading will greatly affect the actual drivable distance of
the vehicle, regardless of the DTE displayed value.
When the DTE value is less than 30 miles (48 km)
estimated driving distance, the DTE display will change
to a LOW FUEL message. This display will continue
until the vehicle runs out of fuel. Adding a significant
amount of fuel to the vehicle will turn off the LOW 4
FUEL message and a new DTE value will display.
Miles Per Gallon (MPG)
Average Fuel Economy Display
This display shows the instantaneous MPG in bar graph
Distance To Empty (DTE)
form while driving. This will monitor the gas mileage in
This display shows the estimated distance that can be
real-time as you drive and can be used to modify driving
traveled with the fuel remaining in the tank. This esti-
habits in order to increase fuel economy.
mated distance is determined by a weighted average of
the instantaneous and average fuel economy, according Vehicle Speed
to the current fuel tank level. DTE cannot be reset Press and release the UP or DOWN button until Vehicle
through the SELECT button. Speed displays highlighted in the EVIC and press the
SELECT button. Press the SELECT button to display the
current speed in mph or km/h. Pressing the SELECT Trip B
button a second time will toggle the unit of measure Shows the total distance traveled for Trip B since the last
between mph or km/h. reset.
NOTE: Changing the unit of measure in the Vehicle Elapsed Time
Speed menu will not change the unit of measure in the Shows the total elapsed time of travel since the last reset
EVIC. when the ignition switch is in the ACC position. Elapsed
time will increment when the ignition switch is in the ON
Trip Info
or START position.
Press and release the UP or DOWN button until Trip
Info is highlighted in the EVIC and press the SELECT To Reset A Trip Function
button. Press and release the UP/DOWN buttons to Reset will only occur while a resettable function is
highlight one of the following functions if you want to selected (highlighted). Press and hold the SELECT button
reset it: to clear the resettable function being displayed.
Trip A Tire PSI
Shows the total distance traveled for Trip A since the last Press and release the UP or DOWN button until Tire
reset. PSI: displays highlighted in the EVIC. Press the SELECT
button to view a graphic of the vehicle with a tire
pressure value at each corner of the graphic.
Units Oil Temperature
Press and release the UP or DOWN button until Units Displays the actual oil temperature.
displays highlighted in the EVIC and press the SELECT
Oil Pressure
button. The EVIC, odometer, and navigation system (if
Displays the actual oil pressure.
equipped) can be changed between English and Metric
units of measure. To make your selection, scroll up or Engine Hours
down until the preferred setting is highlighted, then Displays the number of hours of engine operation.
press and release the SELECT button until a check-mark
Messages 4
appears next to the setting, showing that the setting has
Press and release the UP or DOWN button until Mes-
been selected.
sages: XX displays highlighted in the EVIC. If there is
Vehicle Info (Customer Information Features) more than one message, pressing the SELECT button will
Press and release the UP or DOWN button until Vehicle display a stored warning message. Press and release the
Info displays in the EVIC and press the SELECT button. UP and DOWN buttons if there is more than one message
Press the UP and DOWN button to scroll through the to step through the remaining stored messages. If there
selections below: are no message, pressing the SELECT button will do
nothing.
Coolant Temp
Displays the actual coolant temperature.
Compass / Temperature Display NOTE: A good calibration requires a level surface and
The compass readings indicate the direction the vehicle is an environment free from large metallic objects such as
facing. The EVIC will display one of eight compass buildings, bridges, underground cables, railroad tracks,
readings and the outside temperature. etc.
NOTE: The system will display the last known outside Manual Compass Calibration
temperature when starting the vehicle and may need to If the compass appears erratic and the CAL indicator
be driven several minutes before the updated tempera- does not appear in the EVIC display, you must put the
ture is displayed. Engine temperature can also affect the compass into the Calibration Mode manually, as follows:
displayed temperature; therefore, temperature readings
1. Turn ON the ignition switch.
are not updated when the vehicle is not moving.
Automatic Compass Calibration 2. Press the UP or DOWN button until the Setup
This compass is self-calibrating, which eliminates the (Customer-Programmable Features) menu is reached,
need to manually reset the compass. When the vehicle is then press the SELECT button.
new, the compass may appear erratic and the EVIC will 3. Press the DOWN button until Calibrate Compass is
display CAL until the compass is calibrated. You may displayed in the EVIC.
also calibrate the compass by completing one or more
360degree turns (in an area free from large metal or 4. Press and release the SELECT button to start the
metallic objects) until the CAL indicator displayed in the calibration. The CAL indicator will be displayed in the
EVIC turns off. The compass will now function normally. EVIC.
5. Complete one or more 360degree turns (in an area
free from large metal or metallic objects) until the CAL
indicator turns off. The compass will now function
normally.
Compass Variance
Compass Variance is the difference between Magnetic
North and Geographic North. To compensate for the
differences the variance should be set for the zone where 4
the vehicle is driven, per the zone map. Once properly
set, the compass will automatically compensate for the
differences, and provide the most accurate compass
heading. For the most accurate compass performance, the Compass Variance Map
compass must be set using the following steps.
1. Turn the ignition switch ON.
NOTE: Keep magnetic materials away from the top of
2. Press the UP or DOWN button until the Setup
the instrument panel, such as iPods, Mobile Phones,
(Customer-Programmable Features) menu is reached,
Laptops and Radar Detectors. This is where the compass
then press the SELECT button.
module is located, and it can cause interference with the
compass sensor, and it may give false readings.
3. Press the DOWN button until the Compass Variance press the SELECT button to enter the System Setup
message is displayed in the EVIC, then press the SELECT sub-menu. Press and release the UP or DOWN button to
button. The last variance zone number displays in the select a feature form the following choices:
EVIC.
Language
4. Press and release the SELECT button until the proper When in this display you may select one of five lan-
variance zone is selected, according to the map. guages for all display nomenclature, including the trip
functions and the navigation system (if equipped). Press
5. Press and release the RETURN button to exit.
the UP or DOWN button while in this display and scroll
Customer-Programmable Features through the language choices. Press the SELECT button
(System Setup) to select English, Spanish (Espaol), French (Franais).
Personal Settings allows you to set and recall features Then, as you continue, the information will display in the
when the transmission is in PARK. If the transmission is selected language.
out of PARK or the vehicle begins moving, a warning
NavTurn By Turn
message SYSTEM SETUP NOT AVAILABLE VEHICLE
When this feature is selected, the navigation system
NOT IN PARK displays when you try to select System
utilizes voice commands, guiding through the drive
Setup from the main menu.
route, mile by mile, turn-by-turn until the final destina-
Press and release the UP or DOWN button until System tion is reached. To make your selection, press and release
Setup is highlighted in the main menu of the EVIC. Then the SELECT button until a check-mark appears next to
the feature showing the system has been activated or the Auto Unlock Doors
check-mark is removed showing the system has been When ON is selected, all doors will unlock when the
deactivated. vehicle is stopped and the transmission is in the PARK or
NEUTRAL position and the drivers door is opened. To
Enable/Disable the Rear Park Assist System
make your selection, press and release the SELECT
The Rear Park Assist system will scan for objects behind
button until a check-mark appears next to the feature
the vehicle when the transmission is in the REVERSE
showing the system has been activated or the check-mark
position and the vehicle speed is less than 11 mph
(18 km/h). The system can be enabled with Sound Only,
is removed showing the system has been deactivated. 4
Sound and Display, or turned OFF through the EVIC. To Remote Unlock Sequence
make your selection, press and release the SELECT When Driver Door 1st Press is selected, only the drivers
button until a check-mark appears next to the feature door will unlock on the first press of the Remote Keyless
showing the system has been activated or the check-mark Entry (RKE) transmitter UNLOCK button. When Driver
is removed showing the system has been deactivated. Door 1st Press is selected, you must press the RKE
Refer to Rear Park Assist System in Understanding transmitter UNLOCK button twice, to unlock the passen-
The Features Of Your Vehicle for system function and gers doors. When All Doors 1st Press is selected, all of
operating information. the doors will unlock on the first press of the RKE
transmitter UNLOCK button. To make your selection,
press and release the SELECT button until a check-mark
appears next to the feature showing the system has been In warm weather, the driver vented seat feature will
activated or the check-mark is removed showing the automatically turn on when the remote start is activated.
system has been deactivated. These features will stay on through the duration of
remote start or until the key is turned to RUN. To make
RKE Linked To Memory
your selection, press and release the SELECT button until
When this feature is selected the memory seat, mirror,
a check-mark appears next to the feature showing the
and radio settings will return to the memory set position
system has been activated or the check-mark is removed
when the RKE transmitter UNLOCK button is pressed. If
showing the system has been deactivated.
this feature is not selected then the memory seat, mirror,
and radio settings can only return to the memory set Horn with Remote Lock
position using the door mounted switch. To make your When this feature is selected, a short horn sound will
selection, press and release the SELECT button until a occur when the RKE transmitter LOCK button is pressed.
check-mark appears next to the feature showing the This feature may be selected with or without the Flash
system has been activated or the check-mark is removed Lamps with Lock feature. To make your selection, press
showing the system has been deactivated. and release the SELECT button until a check-mark ap-
pears next to the feature showing the system has been
Remote Start Comfort Sys.
activated or the check-mark is removed showing the
When this feature is selected and the remote start is
system has been deactivated.
activated, the heated steering wheel and driver heated
seat features will automatically turn on in cold weather.
Flash Lamps with Lock Headlamps with Wipers
When ON is selected, the front and rear turn signals will (Available with Auto Headlights Only)
flash when the doors are locked or unlocked with the When ON is selected, and the headlight switch is in the
RKE transmitter. This feature may be selected with or AUTO position, the headlights will turn on approxi-
without the sound horn on lock feature selected. To make mately 10 seconds after the wipers are turned on. The
your selection, press and release the SELECT button until headlights will also turn off when the wipers are turned
a check-mark appears next to the feature showing the off if they were turned on by this feature. To make your
system has been activated or the check-mark is removed selection, press and release the SELECT button until a 4
showing the system has been deactivated. check-mark appears next to the setting, showing that the
setting has been selected.
Headlamp Off Delay
When this feature is selected, the driver can choose to NOTE: Turning the headlights on during the daytime
have the headlights remain on for 0, 30, 60, or 90 seconds causes the instrument panel lights to dim. To increase the
when exiting the vehicle. To make your selection, scroll brightness, refer to Lights in Understanding The
up or down until the preferred setting is highlighted, Features Of Your Vehicle.
then press and release the SELECT button until a check-
Intermittent Wiper Options If Equipped
mark appears next to the setting, showing that the setting
When ON is selected, the system will automatically
has been selected.
activate the windshield wipers if it senses moisture on
the windshield. To make your selection, press and release
the SELECT button until a check-mark appears next to Illuminated Approach
the feature showing the system has been activated or the When this feature is selected, the headlights will activate
check-mark is removed showing the system has been and remain on for up to 90 seconds when the doors are
deactivated. When the system is deactivated, the system unlocked with the RKE transmitter. To make your selec-
reverts to the standard intermittent wiper operation. tion, scroll up or down until the preferred setting is
highlighted, then press and release the SELECT button
Key-Off Power Delay
until a check-mark appears next to the setting, showing
When this feature is selected, the power window
that the setting has been selected.
switches, radio, Uconnect phone (if equipped), DVD
video system (if equipped), power sunroof (if equipped), Flashers with Sliding Door
and power outlets will remain active for up to 10 minutes When this feature is selected the signal lamps activate
after the ignition switch is turned OFF. Opening either when power or manual sliding doors are in operation,
front vehicle door will cancel this feature. To make your signaling other drivers that someone may be exiting or
selection, scroll up or down until the preferred setting is entering the vehicle. To make your selection, press and
highlighted, then press and release the SELECT button release the SELECT button until a check-mark appears
until a check-mark appears next to the setting, showing next to the feature showing the system has been activated
that the setting has been selected. or the check-mark is removed showing the system has
been deactivated.
Easy Entry/Exit Seat To make your selection, press and release the SELECT
This feature provides automatic driver seat positioning to button until a check-mark appears next to the feature
enhance driver mobility when entering and exiting the showing the system has been activated or the check-mark
vehicle. To make your selection, press and release the is removed showing the system has been deactivated.
SELECT button until a check-mark appears next to the
Blind Spot Alert
feature showing the system has been activated or the
There are three selections when operating Blind Spot
check-mark is removed showing the system has been
Alert (Blind Spot Alert Lights, Blind Spot Alert
deactivated.
Lights/CHM, Blind Spot Alert Off). The Blind Spot 4
NOTE: The seat will return to the memorized seat Alert feature can be activated in Blind Spot Alert Lights
location (if Recall Memory with Remote Key Unlock is set mode, when this mode is selected the Blind Spot Monitor
to ON) when the RKE transmitter is used to unlock the (BSM) system is activated and will only show a visual
door. Refer to Driver Memory Seat in Understanding alert in the outside mirrors. The Blind Spot Alert feature
The Features Of Your Vehicle for further information. can be activated in Blind Spot Alert Lights/CHM
mode, in this mode the Blind Spot Monitor (BSM) will
Tilt Mirror In Reverse
show a visual alert in the outside mirrors as well as an
When this feature is selected and the vehicle is placed in
audible alert when the turn signal is on. When Blind
a reverse gear, the drivers side mirror will tilt downward
Spot Alert Off is selected the Blind Spot Monitor (BSM)
to allow the driver to see into the previous blind spot and
system is deactivated.
avoid objects in close proximity to the rear of the vehicle.
To make your selection, press and release the SELECT MEDIA CENTER 730N/430/430N (RHR/RER/RBZ/
button until a check-mark appears next to the feature RHB) CD/DVD/HDD/NAV IF EQUIPPED
showing the system has been activated or the check-mark
NOTE: The sales code is located on the lower right side
is removed showing the system has been deactivated.
of the units faceplate.
NOTE: If your vehicle has experienced any damage in
Refer to your Uconnect Multimedia RHR, RER, RBZ or
the area where the sensor is located, even if the fascia is
RHB users manual for detailed operating instructions.
not damaged, the sensor may have become misaligned.
Take your vehicle to an authorized dealer to verify sensor Operating Instructions
alignment. Having a sensor that is misaligned will result (Voice Command System) If Equipped
in the BSM not operating to specification. Refer to Voice Command in the Uconnect User
Manual located on the DVD for further details.
Calibrate Compass
Refer to Compass Display for more information. Operating Instructions (Uconnect Phone) If
Equipped
Compass Variance
Refer to Uconnect Phone in the Uconnect User
Refer to Compass Display for more information.
Turn Menu Off
Press and release SELECT to turn the menu off.
MEDIA CENTER 130 (SALES CODE RES) Operating Instructions Radio Mode
NOTE: The radio sales code is located on the lower right NOTE: The ignition switch must be in the ON or ACC
side of the radio faceplate. position to operate the radio.
Power Switch/Volume Control (Rotary)
Push the ON/VOLUME control knob to turn on the
radio. Push the ON/VOLUME control knob a second
time to turn off the radio. 4
Electronic Volume Control
The electronic volume control turns continuously (360
degrees) in either direction, without stopping. Turning
the ON/VOLUME control knob to the right increases the
volume, and to the left decreases it.
When the audio system is turned on, the sound will be
set at the same volume level as last played.
Media Center 130 (RES)
SEEK Buttons 4. Adjust the minutes using the right side TUNE/
Press and release the SEEK buttons to search for the next SCROLL control knob. Press the TUNE/SCROLL control
listenable station in AM/FM mode. Press the right switch knob to save time change.
to seek up and the left switch to seek down. The radio
5. To exit, press any button/knob, or wait five seconds.
will remain tuned to the new station until you make
another selection. Holding either button will bypass RW/FF
stations without stopping, until you release it. Pressing the RW (Rewind) or FF (Fast Forward) buttons
causes the tuner to search for the next frequency in the
TIME Button
direction of the arrows. This feature operates in either
Press the TIME button to alternate display of the time
AM or FM frequencies.
and radio frequency.
TUNE Control
Clock Setting Procedure
Turn the rotary TUNE/SCROLL control knob clockwise
1. Press and hold the TIME button until the hours blink. to increase or counterclockwise to decrease the frequency.
2. Adjust the hours by turning the right side TUNE/ Setting the Tone, Balance, and Fade
SCROLL control knob. Push the rotary TUNE/SCROLL control knob and BASS
will display. Turn the TUNE/SCROLL control knob to
3. After adjusting the hours, press the right side TUNE/
the right or left to increase or decrease the bass tones.
SCROLL control knob to set the minutes. The minutes
will begin to blink.
Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to
time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade.
control knob to the right or left to increase or decrease the
AM/FM Button
mid-range tones.
Press the buttons to select either AM or FM mode.
Push the rotary TUNE/SCROLL control knob a third
SET/RND Button To Set the Pushbutton
time and TREBLE will display. Turn the TUNE/SCROLL
Memory
treble tones.
When you are receiving a station that you wish to 4
commit to pushbutton memory, press the SET/RND
Push the rotary TUNE/SCROLL control knob a fourth button. The symbol SET 1 will now show in the display
time and BALANCE will display. Turn the TUNE/ window. Select the button (1 to 6) you wish to lock onto
SCROLL control knob to the right or left to adjust the this station and press and release that button. If a button
sound level from the right or left side speakers. is not selected within five seconds after pressing the
SET/RND button, the station will continue to play but
Push the rotary TUNE/SCROLL control knob a fifth time
will not be stored into pushbutton memory.
and FADE will display. Turn the TUNE/SCROLL control
knob to the left or right to adjust the sound level between
the front and rear speakers.
You may add a second station to each pushbutton by Operation Instructions CD MODE For CD And
repeating the above procedure with this exception: Press MP3 Audio Play
the SET/RND button twice and SET 2 will show in the
NOTE:
display window. Each button can be set for SET 1 and
The ignition switch must be in the ON or ACC
SET 2 in both AM and FM. This allows a total of 12 AM
position to operate the radio.
and 12 FM stations to be stored into pushbutton memory.
The stations stored in SET 2 memory can be selected by This radio is capable of playing compact discs (CD),
pressing the pushbutton twice. recordable compact discs (CD-R), rewritable compact
discs (CD-RW), compact discs with MP3 tracks and
Every time a preset button is used, a corresponding
multisession compact discs with CD and MP3 tracks.
button number will display.
Inserting Compact Disc(s)
Buttons 1 - 6
Gently insert one CD into the CD player with the CD
These buttons tune the radio to the stations that you
label facing up. The CD will automatically be pulled into
commit to pushbutton memory (12 AM and 12 FM
the CD player and the CD icon will illuminate on the
stations).
radio display. If a CD does not go into the slot more than
DISC Button 1.0 in (2.5 cm), a disc may already be loaded and must be
Pressing the DISC button will allow you to switch from ejected before a new disc can be loaded.
AM/FM modes to Disc modes.
If you insert a disc with the ignition ON and the radio EJECT Button - Ejecting a CD
ON, the unit will switch from radio to CD mode and Press the EJECT button to eject the CD.
begin to play when you insert the disc. The display will
show the track number, and index time in minutes and
seconds. Play will begin at the start of track 1.
If you have ejected a disc and have not removed it within
CAUTION! 10 seconds, it will be reloaded. If the CD is not removed,
This CD player will accept 4-3/4 in (12 cm) discs
the radio will reinsert the CD but will not play it. 4
only. The use of other sized discs may damage the A disc can be ejected with the radio and ignition OFF.
CD player mechanism.
NOTE: Ejecting with the ignition OFF is not allowed on
Do not use adhesive labels. These labels can peel convertible or soft-top models (if equipped).
away and jam the player mechanism.
The RES Media Center is a single CD player. Do
not attempt to insert a second CD if one is already
loaded.
SEEK Button SET/RND Button (Random Play Button)
Press the right SEEK button for the next selection on the Press this button while the CD is playing to activate
CD. Press the left SEEK button to return to the beginning Random Play. This feature plays the selections on the
of the current selection, or return to the beginning of the compact disc in random order to provide an interesting
previous selection if the CD is within the first second of change of pace.
the current selection. Pressing and holding the SEEK
Press the right SEEK button to move to the next ran-
button will allow faster scrolling through the tracks in
domly selected track.
CD and MP3 modes.
Press the RND button a second time to stop Random
TIME Button
Play.
Press this button to change the display from a large CD
playing time display to a small CD playing time display. Notes on Playing MP3 Files
The radio can play MP3 files; however, acceptable MP3
RW/FF
file recording media and formats are limited. When
Press and hold the FF (Fast Forward) button and the CD
writing MP3 files, pay attention to the following restric-
player will begin to fast forward until FF is released, or
tions.
RW or another CD button is pressed. The RW (Reverse)
button works in a similar manner. Supported Media (Disc Types)
The MP3 file recording media supported by the radio are
AM/FM Button
CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
Press the button to select either AM or FM mode.
Supported Medium Formats (File Systems) Maximum number of characters in file/folder names:
The medium formats supported by the radio are ISO 9660 Level 1: 12 (including a separator . and a three-
Level 1 and Level 2 and includes the Joliet extension. character extension)
When reading discs recorded using formats other than
ISO 9660 Level 1 and Level 2, the radio may fail to read Level 2: 31 (including a separator . and a three-
files properly and may be unable to play the file nor- character extension)
mally. UDF and Apple HFS formats are not supported. Multisession disc formats are supported by the radio.
The radio uses the following limits for file systems: Multisession discs may contain combinations of normal 4
CD audio tracks and computer files (including MP3 files).
Maximum number of folder levels: 8 Discs created with an option such as keep disc open after
Maximum number of files: 255 writing are most likely multisession discs. The use of
multisession for CD audio or MP3 playback may result in
Maximum number of folders. (The radio display of file longer disc loading times.
names and folder names is limited. For large numbers
of files and/or folders, the radio may be unable to Supported MP3 File Formats
display the file name and folder name, and will assign The radio will recognize only files with the *.MP3 exten-
a number instead. With a maximum number of files, sion as MP3 files. Non-MP3 files named with the *.MP3
exceeding 20 folders will result in this display. With 200 extension may cause playback problems. The radio is
files, exceeding 50 folders will result in this display.) designed to recognize the file as an invalid MP3 and will
not play the file.
When using the MP3 encoder to compress audio data to Playlist files are not supported. MP3 Pro files are not
an MP3 file, the bit rate and sampling frequencies in the supported.
following table are supported. In addition, variable bit
Playback of MP3 Files
rates (VBR) are also supported. The majority of MP3 files
When a medium containing MP3 data is loaded, the
use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or
radio checks all files on the medium. If the medium
VBR bit rate.
contains a lot of folders or files, the radio will take more
MPEG Sampling Fre- time to start playing the MP3 files.
Bit Rate (kbps)
Specification quency (kHz)
320, 256, 224, Loading times for playback of MP3 files may be affected
MPEG-1 Audio 192, 160, 128, by the following:
48, 44.1, 32
Layer 3 112, 96, 80, 64, Media - CD-RW media may take longer to load than
56, 48, 40, 32
CD-R media
160, 128, 144,
MPEG-2 Audio 112, 96, 80, 64, Medium formats - Multisession discs may take longer
24, 22.05, 16
Layer 3 56, 48, 40, 32, 24, to load than non-multisession discs
16, 8
Number of files and folders - Loading times will
ID3 Tag information for artist, song title, and album title increase with more files and folders
are supported for version 1 ID3 tags. ID3 version 2 is not
supported by the radios.
To increase the speed of disc loading, it is recommended NOTE: The AUX device must be turned on and the
to use CD-R media and single-session discs. To create a devices volume set to proper level. If the AUX audio is
single-session disc, enable the Disc at Once option not loud enough, turn the devices volume up. If the AUX
before writing to the disc. audio sounds distorted, turn the devices volume down.
Operation Instructions - Auxiliary Mode TIME Button (Auxiliary Mode)
The auxiliary (AUX) jack is an audio input jack, which Press this button to change the display to time of day. The
allows the user to plug in a portable device, such as an time of day will display for five seconds (when ignition is
MP3 player, or cassette player, and utilize the vehicles OFF). 4
audio system to amplify the source and play through the
vehicle speakers.
Pressing the DISC/AUX button will change the mode to
auxiliary device if the AUX jack is connected.
MEDIA CENTER 130 WITH SATELLITE RADIO Operating Instructions Radio Mode
(SALES CODE RES+RSC)
NOTE: The ignition switch must be in the ON/RUN or
NOTE: The radio sales code is located on the lower right ACC position to operate the radio.
side of the radio faceplate.
Power Switch/Volume Control (Rotary)
Push the ON/VOLUME control knob to turn on the
radio. Push the ON/VOLUME control knob a second
time to turn off the radio.
Electronic Volume Control
The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the
ON/VOLUME control knob to the right increases the
volume and to the left decreases it.
When the audio system is turned on, the sound will be
set at the same volume level as last played.
Media Center 130 (RES/RSC)
SEEK Buttons If your vehicle is not equipped with or this feature is not
Press and release the SEEK buttons to search for the next available on your vehicle, a Not Equipped With
listenable station in AM/FM mode. Press the right switch Uconnect Phone message will display on the radio
to seek up and the left switch to seek down. The radio screen.
will remain tuned to the new station until you make
Phone Button Uconnect Phone If Equipped
another selection. Holding either button will bypass
Press this button to operate the Uconnect Phone feature
stations without stopping until you release it.
(if equipped). Refer to Uconnect Phone in the
Voice Command System (Radio) If Equipped Uconnect User Manual located on the DVD for further 4
Refer to Voice Command in the Uconnect User details.
If your vehicle is not equipped with or this feature is not
Voice Command Button Uconnect Phone If available on your vehicle, a Not Equipped With
Equipped Uconnect Phone message will display on the radio
Press this button to operate the Uconnect Phone feature screen.
(if equipped). Refer to Voice Command in the
TIME Button
Uconnect User Manual located on the DVD for further
Press the TIME button to alternate display of the time
details.
and radio frequency.
Clock Setting Procedure starting at Step 2. For vehicles not equipped with satellite
radio, press the SETUP button and then follow the above
1. Press and hold the TIME button until the hours blink.
procedure, starting at Step 2.
2. Adjust the hours by turning the right side TUNE/
INFO Button
SCROLL control knob.
Press the INFO button for an RDS station (one with call
3. After adjusting the hours, press the right side TUNE/ letters displayed). The radio will return a Radio Text
SCROLL control knob to set the minutes. The minutes message broadcast from an FM station (FM mode only).
will begin to blink.
RW/FF
4. Adjust the minutes using the right side TUNE/ Pressing the RW (Rewind) or FF (Fast Forward) buttons
SCROLL control knob. Press the TUNE/SCROLL control causes the tuner to search for the next frequency in the
knob to save time change. direction of the arrows. This feature operates in either
AM or FM frequencies.
5. To exit, press any button/knob or wait five seconds.
TUNE Control
The clock can also be set by pressing the SETUP button.
For vehicles equipped with satellite radio, press the
to increase or counterclockwise to decrease the frequency.
SETUP button, use the TUNE/SCROLL control to select
SET CLOCK, and then follow the above procedure,
Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob a fifth time
Push the rotary TUNE/SCROLL control knob and BASS and FADE will display. Turn the TUNE/SCROLL control
will display. Turn the TUNE/SCROLL control knob to knob to the left or right to adjust the sound level between
the right or left to increase or decrease the bass tones. the front and rear speakers.
Push the rotary TUNE/SCROLL control knob a second Push the rotary TUNE/SCROLL control knob again to
time and MID will display. Turn the TUNE/SCROLL exit setting tone, balance, and fade.
mid-range tones.
MUSIC TYPE Button 4
Pressing this button once will turn on the Music Type
Push the rotary TUNE/SCROLL control knob a third mode for five seconds. Pressing the MUSIC TYPE button
time and TREBLE will display. Turn the TUNE/SCROLL or turning the TUNE/SCROLL control knob within five
control knob to the right or left to increase or decrease the seconds will allow the program format type to be se-
treble tones. lected. Many radio stations do not currently broadcast
Music Type information.
Push the rotary TUNE/SCROLL control knob a fourth
time and BALANCE will display. Turn the TUNE/
SCROLL control knob to the right or left to adjust the
sound level from the right or left side speakers.
Toggle the MUSIC TYPE button to select the following Program Type 16-Digit Character Display
format types: Public Public
Program Type 16-Digit Character Display Rhythm and Blues R&B
No program type or Religious Music Rel Musc
None
undefined
Religious Talk Rel Talk
Adult Hits Adlt Hit
Rock Rock
Classical Classicl
Soft Soft
Classic Rock Cls Rock
Soft Rock Soft Rck
College College
Soft Rhythm and Blues Soft R&B
Country Country
Sports Sports
Foreign Language Language
Talk Talk
Information Inform
Top 40 Top 40
Jazz Jazz
Weather Weather
News News
Nostalgia Nostalga By pressing the SEEK button when the Music Type icon is
displayed, the radio will be tuned to the next frequency
Oldies Oldies
station with the same selected Music Type name. The
Personality Persnlty Music Type function only operates when in the FM mode.
If a preset button is activated while in the Music Type SET/RND Button To Set the Pushbutton
(Program Type) mode, the Music Type mode will be Memory
exited and the radio will tune to the preset station. When you are receiving a station that you wish to
commit to pushbutton memory, press the SET/RND
SETUP Button
button. The symbol SET 1 will now show in the display
Pressing the SETUP button allows you to select between
window. Select the button (16) you wish to lock onto this
the following items:
station and press and release that button. If a button is
Set Clock Pressing the SELECT button will allow not selected within five seconds after pressing the SET/ 4
you to set the clock. Adjust the hours by turning the RND button, the station will continue to play but will not
TUNE/SCROLL control knob. After adjusting the be stored into pushbutton memory.
hours, press the TUNE/SCROLL control knob to set
You may add a second station to each pushbutton by
the minutes. The minutes will begin to blink. Adjust
repeating the above procedure with this exception: Press
the minutes using the right side TUNE/SCROLL
the SET/RND button twice and SET 2 will show in the
control knob. Press the TUNE/SCROLL control knob
display window. Each button can be set for SET 1 and
to save time change.
SET 2 in both AM and FM. This allows a total of 12 AM
AM/FM Button and 12 FM stations to be stored into pushbutton memory.
Press the button to select either AM or FM mode. The stations stored in SET 2 memory can be selected by
pressing the pushbutton twice.
Every time a preset button is used, a corresponding This radio is capable of playing compact discs (CD),
button number will display. recordable compact discs (CD-R), rewritable compact
discs (CD-RW), compact discs with MP3 tracks and
Buttons 1 - 6
multisession compact discs with CD and MP3 tracks.
These buttons tune the radio to the stations that you
commit to pushbutton memory (12 AM and 12 FM Inserting Compact Disc(s)
stations). Gently insert one CD into the CD player with the CD
label facing up. The CD will automatically be pulled into
DISC/AUX Button
the CD player and the CD icon will illuminate on the
Pressing the DISC/AUX button will allow you to switch
radio display. If a CD does not go into the slot more than
from AM/FM modes to DISC/AUX mode.
1.0 in (2.5 cm), a disc may already be loaded and must be
Operation Instructions CD MODE for CD and ejected before a new disc can be loaded.
MP3 Audio Play
If you insert a disc with the ignition ON/RUN and the
NOTE: radio ON, the unit will switch from radio to CD mode
The ignition switch must be in the ON/RUN or ACC and begin to play when you insert the disc. The display
position to operate the radio. will show the track number, and index time in minutes
and seconds. Play will begin at the start of track 1.
A disc can be ejected with the radio and ignition OFF.
CAUTION!
NOTE: Ejecting with the ignition OFF is not allowed on
This CD player will accept 43/4 in (12 cm) discs
convertible or soft-top models (if equipped).
only. The use of other sized discs may damage the
CD player mechanism. SEEK Button
Do not use adhesive labels. These labels can peel Press the right SEEK button for the next selection on the
away and jam the player mechanism. CD. Press the left SEEK button to return to the beginning
The RES Media Center is a single CD player. Do of the current selection, or return to the beginning of the 4
not attempt to insert a second CD if one is already previous selection if the CD is within the first second of
loaded. the current selection. Pressing and holding the SEEK
button will allow faster scrolling through the tracks in
EJECT Button - Ejecting a CD CD and MP3 modes.
Press the EJECT button to eject the CD. TIME Button
Press this button to change the display from a large CD
playing time display to a small CD playing time display.
If you have ejected a disc and have not removed it within

10 seconds, it will be reloaded. If the CD is not removed,
the radio will reinsert the CD but will not play it.
RW/FF Notes On Playing MP3 Files
Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3
begin to fast forward until FF is released or RW or file recording media and formats are limited. When
another CD button is pressed. The RW (Reverse) button writing MP3 files, pay attention to the following restric-
works in a similar manner. tions.
AM/FM Button Supported Media (Disc Types)
Press the button to select either AM or FM mode. The MP3 file recording media supported by the radio are
CDDA, CD-R, CD-RW, MP3, and CDDA+MP3.
SET/RND Button (Random Play Button)
Press this button while the CD is playing to activateSupported Medium Formats (File Systems)
Random Play. This feature plays the selections on theThe medium formats supported by the radio are ISO 9660
compact disc in random order to provide an interesting
Level 1 and Level 2 and includes the Joliet extension.
change of pace. When reading discs recorded using formats other than
ISO 9660 Level 1 and Level 2, the radio may fail to read
Press the right SEEK button to move to the next ran-
files properly and may be unable to play the file nor-
domly selected track.
mally. UDF and Apple HFS formats are not supported.
Press the SET/RND button a second time to stop Ran-
The radio uses the following limits for file systems:
dom Play.
Maximum number of folder levels: 8
Maximum number of files: 255 Discs created with an option such as keep disc open after
writing are most likely multisession discs. The use of
Maximum number of folders. (The radio display of file
multisession for CD audio or MP3 playback may result in
names and folder names is limited. For large numbers
longer disc loading times.
of files and/or folders, the radio may be unable to
display the file name and folder name and will assign Supported MP3 File Formats
a number instead. With a maximum number of files, The radio will recognize only files with the *.MP3 exten-
exceeding 20 folders will result in this display. With sion as MP3 files. Non-MP3 files named with the *.MP3
200 files, exceeding 50 folders will result in this extension may cause playback problems. The radio is 4
display.) designed to recognize the file as an invalid MP3 and will
not play the file.
Maximum number of characters in file/folder names:
When using the MP3 encoder to compress audio data to
Level 1: 12 (including a separator . and a three-
an MP3 file, the bit rate and sampling frequencies in the
character extension)
following table are supported. In addition, variable bit
Level 2: 31 (including a separator . and a three- rates (VBR) are also supported. The majority of MP3 files
character extension) use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or
VBR bit rates.
Multisession disc formats are supported by the radio.
Multisession discs may contain combinations of normal
CD audio tracks and computer files (including MP3 files).
MPEG Sampling Fre- Playback of MP3 Files

Bit Rate (kbps) When a medium containing MP3 data is loaded, the
Specification quency (kHz)
320, 256, 224, radio checks all files on the medium. If the medium
MPEG-1 Audio 192, 160, 128, contains a lot of folders or files, the radio will take more
48, 44.1, 32 time to start playing the MP3 files.
Layer 3 112, 96, 80, 64,
56, 48, 40, 32
Loading times for playback of MP3 files may be affected
160, 128, 144, by the following:
MPEG-2 Audio 112, 96, 80, 64,
24, 22.05, 16
Layer 3 56, 48, 40, 32, 24, Media - CD-RW media may take longer to load than
16, 8 CD-R media
ID3 Tag information for artist, song title, and album title Medium formats - Multisession discs may take longer
are supported for version 1 ID3 tags. ID3 version 2 is not to load than non-multisession discs
supported by the radios.
Number of files and folders - Loading times will
Playlist files are not supported. MP3 Pro files are not increase with more files and folders
supported.
To increase the speed of disc loading, it is recommended
to use CD-R media and single-session discs. To create a
single-session disc, enable the Disc at Once option
before writing to the disc.
LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds
Pressing the LIST button will bring up a list of all folders to return to elapsed time display.
on the disc. Scrolling up or down the list is done by
Operation Instructions - Auxiliary Mode
turning the TUNE/SCROLL control knob. Selecting a
The auxiliary (AUX) jack is an audio input jack which
folder by pressing the TUNE/SCROLL control knob will
allows the user to plug in a portable device such as an
begin playing the files contained in that folder (or the
MP3 player or cassette player and utilize the vehicles
next folder in sequence if the selection does not contain
audio system to amplify the source and play through the
playable files).
vehicle speakers. 4
The folder list will time out after five seconds.
Pressing the AUX button will change the mode to auxil-
INFO Button (CD Mode for MP3 Play) iary device if the AUX jack is connected.
Pressing the INFO button repeatedly will scroll through
NOTE: The AUX device must be turned on and the
the following TAG information: Song Title, Artist, File
devices volume set to the proper level. If the AUX audio
Name, and Folder Name (if available).
is not loud enough, turn the devices volume up. If the
Press the INFO button once more to return to elapsed AUX audio sounds distorted, turn the devices volume
time priority mode. down.
Press and hold the INFO button for three seconds or
more and the radio will display song titles for each file.
TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a wel-
Press this button to change the display to time of day. The come kit that contains general information, including
time of day will display for five seconds (when the how to setup your on-line listening account. For further
ignition is OFF). information, call the toll-free number 888-539-7474, or
visit the Sirius web site at www.sirius.com, or at www-
Uconnect Multimedia (Satellite Radio) If
.siriuscanada.ca for Canadian residents.
Equipped
Satellite radio uses direct satellite-to-receiver broadcast- Electronic Serial Number/Sirius Identification
ing technology to provide clear digital sound, coast to Number (ESN/SID)
coast. The subscription service provider is Sirius Satellite Please have the following information available when
Radio. This service offers over 130 channels of music, calling:
sports, news, entertainment, and programming for chil-
1. The Electronic Serial Number/Sirius Identification
dren, directly from its satellites and broadcasting studios.
Number (ESN/SID).
NOTE: Sirius service is not available in Hawaii and has
2. Your Vehicle Identification Number.
limited coverage in Alaska.
To access the ESN/SID, refer to the following steps:
System Activation
Sirius Satellite Radio service is pre-activated, and you ESN/SID Access
may begin listening immediately to the one year of audio With the ignition switch in the ON/RUN or ACC posi-
service that is included with the factory-installed satellite tion and the radio on, press the SETUP button and scroll
using the TUNE/SCROLL control knob until Sirius ID is Reception Quality
selected. Press the TUNE/SCROLL control knob and the Satellite reception may be interrupted due to one of the
Sirius ID number will display. The Sirius ID number following reasons:
display will time out in two minutes. Press any button on
The vehicle is parked in an underground parking
the radio to exit this screen.
structure or under a physical obstacle.
Selecting Uconnect Multimedia (Satellite) Mode
Dense tree coverage may interrupt reception in the
Press the SAT button until SAT appears in the display. A
CD may remain in the radio while in the Satellite radio
form of short audio mutes. 4
mode. Driving under wide bridges or along tall buildings can
cause intermittent reception.
Satellite Antenna
To ensure optimum reception, do not place items on the Placing objects over or too close to the antenna can
roof around the rooftop antenna location. Metal objects cause signal blockage.
placed within the line of sight of the antenna will cause
Operating Instructions - Uconnect Multimedia
decreased performance. Larger luggage items such as
(Satellite) Mode
bikes should be placed as far rearward as possible, within
the loading design of the rack. Do not place items directly NOTE: The ignition switch must be in the ON/RUN or
on or above the antenna. ACC position to operate the radio.
SEEK Buttons additional three seconds will make the radio display the
Press and release the SEEK buttons to search for the next Song Title all of the time (press and hold again to return
channel in Satellite mode. Press the right switch to seek to normal display).
up and the left switch to seek down. The radio will
RW/FF
remain tuned to the new channel until you make another
Pressing the RW (Rewind) or FF (Fast Forward) buttons
selection. Holding either button will bypass channels
causes the tuner to search for the next channel in the
without stopping until you release it.
direction of the arrows.
SCAN Button
TUNE Control (Rotary)
Pressing the SCAN button causes the tuner to search for
the next channel, pausing for eight seconds before con-
to increase or counterclockwise to decrease the channel.
tinuing to the next. To stop the search, press the SCAN
button a second time. MUSIC TYPE Button
Pressing this button once will turn on the Music Type
INFO Button
mode for five seconds. Pressing the MUSIC TYPE button
Pressing the INFO button will cycle the display informa-
or turning the TUNE/SCROLL control knob within five
tion between Artist, Song Title, and Composer (if avail-
seconds will allow the program format type to be se-
able). Also, pressing and holding the INFO button for an
lected.
Toggle the MUSIC TYPE button again to select the music SET Button To Set the Pushbutton Memory
type. When you are receiving a channel that you wish to
commit to pushbutton memory, press the SET button.
By pressing the SEEK button when the Music Type
The symbol SET 1 will now show in the display window.
function is active, the radio will be tuned to the next
Select the button (1-6) you wish to lock onto this channel
channel with the same selected Music Type name.
and press and release that button. If a button is not
If a preset button is activated while in the Music Type selected within five seconds after pressing the SET but-
(Program Type) mode, the Music Type mode will be ton, the channel will continue to play but will not be 4
exited and the radio will tune to the preset channel. stored into pushbutton memory.
SETUP Button You may add a second channel to each pushbutton by
Pressing the SETUP button allows you to select the repeating the above procedure with this exception: Press
following items: the SET button twice and SET 2 will show in the display
window. Each button can be set for SET 1 and SET 2. This
Display Sirius ID number Press the AUDIO/
allows a total of 12 Satellite channels to be stored into
SELECT button to display the Sirius ID number. This
pushbutton memory. The channels stored in SET 2
number is used to activate, deactivate, or change the
memory can be selected by pressing the pushbutton
Sirius subscription.
twice.
Every time a preset button is used, a corresponding This feature allows an iPod or external USB device to be
button number will display. plugged into the USB port, located in the glove compart-
ment.
Buttons 1 - 6
These buttons tune the radio to the channels that you iPod control supports Mini, 4G, Photo, Nano, 5G iPod
commit to pushbutton memory (12 Satellite stations). and iPhone devices. Some iPod software versions may
not fully support the iPod control features. Please visit
Operating Instructions (Uconnect Phone) If
Apples website for software updates.
Equipped
Refer to Uconnect Phone in the Uconnect User NOTE:
Manual located on the DVD for further details. If the radio has a USB port, refer to the appropriate
Uconnect Multimedia radio Users Manual for
iPod/USB/MP3 CONTROL IF EQUIPPED iPod or external USB device support capability.
NOTE: This section is for sales code RES and REQ/ Connecting an iPod or consumer electronic audio
REL/RET radios only with Uconnect. For sales code device to the AUX port located in the radio faceplate,
RBZ/RHB, RHR, RHP, RHW or RB2 touch-screen radio plays media, but does not use the iPod /MP3 control
iPod/USB/MP3 control feature, refer to the separate feature to control the connected device.
RBZ/RHB, RHR, RHP, RHW or RB2 Users Manual.
iPod/USB/MP3 control is available only if equipped as
an option with these radios.
Connecting The iPod Or External USB Device Once the audio device is connected and synchronized to
Use the connection cable to connect an iPod or external the vehicles iPod/USB/MP3 control system (iPod or
USB device to the vehicles USB connector port which is external USB device may take a few minutes to connect),
located in the glove compartment. the audio device starts charging and is ready for use by
pressing radio switches, as described below.
NOTE: If the audio device battery is completely dis-
charged, it may not communicate with the iPod/USB/
MP3 control system until a minimum charge is attained. 4
Leaving the audio device connected to the iPod/USB/
MP3 control system may charge it to the required level.
Using This Feature
By using iPod cable or external USB device to connect to
USB port:
The audio device can be played on the vehicles sound
system, providing metadata (artist, track title, album,
USB Connector Port
etc.) information on the radio display.
The audio device can be controlled using the radio Play Mode
buttons to Play, Browse, and List the iPod contents. When switched to iPod/USB/MP3 control mode, the
iPod or external USB device automatically starts Play
The audio device battery charges when plugged into
mode. In Play mode, the following buttons on the radio
the USB/AUX connector (if supported by the specific
faceplate may be used to control the iPod or external
audio device)
USB device and display data:
Controlling The iPod Or External USB Device
Use the TUNE control knob to select the next or
Using Radio Buttons
previous track.
To get into the iPod/USB/MP3 control mode and access
a connected audio device, either press the AUX button Turning it clockwise (forward) by one click, while
on the radio faceplate or press the VR button and say playing a track, skips to the next track or press the
USB or Switch to USB. Once in the iPod/USB/MP3 VR button and say Next Track.
control mode, audio tracks (if available from audio
Turning it counterclockwise (backward) by one
device) start playing over the vehicles audio system.
click, will jump to the previous track in the list or
press the VR button and say Previous Track
Jump backward in the current track by pressing and to the next screen of data for that track. Once all
holding the << RW button. Holding the << RW screens have been viewed, the last INFO button press
button long enough will jump to the beginning of will go back to the play mode screen on the radio.
the current track.
Pressing the REPEAT button will change the audio
Jump forward in the current track by pressing and device mode to repeat the current playing track or
holding the FF >> button. press the VR button and say Repeat ON or Repeat
Off.
A single press backward << RW or forward FF >> will 4
jump backward or forward respectively, for five Press the SCAN button to use iPod/USB/MP3 de-
seconds. vice scan mode, which will play the first 10 seconds of
each track in the current list and then forward to the
Use the << SEEK and SEEK >> buttons to jump to the
next song. To stop SCAN mode and start playing the
previous or next track. Pressing the SEEK >> button
desired track, when it is playing the track, press the
during play mode will jump to the next track in the
SCAN button again. During Scan mode, pressing the
list, or press the VR button and say Next or Previous
<< SEEK and SEEK >> buttons will select the previ-
Track.
ous and next tracks.
While a track is playing, press the INFO button to see
RND button (available on sales code RES radio only):
the associated metadata (artist, track title, album, etc.)
Pressing this button toggles between Shuffle ON and
for that track. Pressing the INFO button again jumps
Shuffle OFF modes for the iPod or external USB
device, or press the VR button and say Shuffle ON or fast will scroll through the list faster. During fast
Shuffle Off. If the RND icon is showing on the radio scroll, a slight delay in updating the information on
display, then the shuffle mode is ON. the radio display may be noticeable.
List Or Browse Mode During all List modes, the iPod displays all lists in
During Play mode, pressing any of the buttons described wrap-around mode. So if the track is at the
below, will bring up List mode. List mode enables bottom of the list, just turn the wheel backward
scrolling through the list of menus and tracks on the (counterclockwise) to get to the track faster.
audio device.
In List mode, the radio PRESET buttons are used as
TUNE control knob: The TUNE control knob functions shortcuts to the following lists on the iPod or
in a similar manner as the scroll wheel on the audio external USB device.
device or external USB device.
Preset 1 Playlists
Turning it clockwise (forward) and counterclock-
Preset 2 Artists
wise (backward) scrolls through the lists, displaying
the track detail on the radio display. Once the track Preset 3 Albums
to be played is highlighted on the radio display,
Preset 4 Genres
press the TUNE control knob to select and start
playing the track. Turning the TUNE control knob Preset 5 Audiobooks
Preset 6 Podcasts
CAUTION!
Pressing a PRESET button will display the current
Leaving the iPod or external USB device (or any
list on the top line and the first item in that list on
supported device) anywhere in the vehicle in
the second line.
extreme heat or cold can alter the operation or
To exit List mode without selecting a track, press the damage the device. Follow the device manufactur-
same PRESET button again to go back to Play ers guidelines.
mode. Placing items on the iPod or external USB device, 4
LIST button: The LIST button will display the top or connections to the iPod or external USB device
level menu of the iPod or external USB device. Turn in the vehicle, can cause damage to the device
the TUNE control knob to list the top-menu item to be and/or to the connectors.
selected and press the TUNE control knob. This will
display the next sub-menu list item on the audio WARNING!
device, then follow the same steps to go to the desired
track in that list. Not all iPod or external USB device Do not plug in or remove the iPod or external USB
sub-menu levels are available on this system. device while driving. Failure to follow this warning
could result in an accident.
MUSIC TYPE button: The MUSIC TYPE button is
another shortcut button to the genre listing on your
audio device.
Bluetooth Streaming Audio (BTSA) 2. After the Ready prompt and the following beep, say
Music can be streamed from your cellular phone to the Setup, then Select Audio Devices.
Uconnect phone system.
3. Say the name of the audio device or ask the
Controlling BTSA Using Radio Buttons Uconnect phone system to list audio devices.
To get into the BTSA mode, press either AUX button on
Next Track
the radio or press the VR button and say Bluetooth
Use the SEEK UP button, or press the VR button on the
Streaming Audio.
radio and say Next Track to jump to the next track
Play Mode music on your cellular phone.
When switched to BTSA mode, some audio devices can
Previous Track
start playing music over the vehicles audio system, but
Use the SEEK DOWN button, or press the VR button on
some devices require the music to be initiated on the
the radio and say Previous Track to jump to the
device first, then it will get streamed to the Uconnect
previous track music on your cellular phone.
phone system. Seven devices can be paired to the
Uconnect phone system, but just one can be selected Browse
and played. Browsing is not available on a BTSA device. Only the
current song that is playing will display info.
Selecting Different Audio Device
1. Press PHONE button to begin.
UCONNECT MULTIMEDIA VIDEO Cycle the ignition to the ON or ACC position.
ENTERTAINMENT SYSTEM (VES) IF
Turn on the VES player (if equipped on Dual Screen
EQUIPPED
System) by pushing the Power button, located on the
Getting Started far left, or by pressing the button on the Remote
Control.
Screen(s) located in the overhead console : Unfold the
overhead LCD screen(s) by pushing the button on the When the Video Screen(s) are open and a DVD is
overhead console behind the screen(s). inserted into the VES player, the screen(s) turn(s) on 4
automatically, the headphone transmitters turn on and
playback begins.
For Dual Video Screen System, Channel 1 on the
Remote Control and Headphones refers to Screen 1
(second row) and Channel 2 on the Remote Control
and Headphones refers to Screen 2 (third row). Refer
to the Dual Video Screen section for more information.
Play Video Games
Connect the video game console to the Auxiliary RCA
input jacks (1 set or 2 depending on vehicle) located on
the back of the center console or on left side behind the
second row seat.
1. Video In Yellow
2. Left Audio In White
3. Right Audio In Red
4. AUX 2 Inputs (If Equipped)
5. Power Outlet
6. Power Inverter
When connecting an external source to the AUX input, be 2. While looking at the video screen, highlight VES AUX
sure to follow the standard color coding for the VES 1 or 2 (depending which AUX input the gaming console
jacks: is plugged into), by either pressing Up/Down/Left/
Right buttons or by repeatedly pressing the MODE
NOTE: Certain high-end video games, such as Playsta-
button, then press ENTER on the Remote Control.
tion3 and XBox360 will exceed the power limit of the
vehicles Power Inverter. Refer to the Power Inverter
section in your vehicles Owners Manual for more
information. 4
Ensure the Remote Control and Headphone switch is on
Channel 1.
Using The Remote Control
1. Press the MODE button on the Remote Control.
Select VES AUX1 Mode On The VES Screen

Using The Touch-Screen Radio Controls 3. Touch the 1 soft-key and then touch either AUX 1 or
AUX 2 in the VES column (depending which AUX input
1. Press the MENU hard-key on the radio faceplate.
is used). To exit press the back arrow soft-key at the top
2. Touch the Rear VES soft-key to display the Rear VES of the screen.
Controls. If a channel list is displayed, press the HIDE
LIST soft-key to display the Rear VES Controls screen.
Select Channel/Screen 1 And

AUX 1 In The VES Column
Rear VES Soft-key
Listen To An Audio Source On Channel 2 While A
Video Is Playing On Channel 1
Ensure the Remote Control and Headphone switch is on
Channel 2.
1. Press the MODE button on the Remote Control and
the Mode Select Screen will display, unless a video is 4
playing then only a small banner will appear on the
bottom of the screen.
2. While looking at the video screen, either press Up/
Down/Left/Right on the Remote Control to highlight the Select FM Mode On The VES Screen
desired audio source or repeatedly press the MODE
button on the remote until the desired audio source
appears on the screen.
Using The Touch-Screen Radio Controls 3. To listen to an audio source on Channel 2 while a
video is playing on Channel 1, touch the 2 soft-key and
choose an audio source. To exit touch the back arrow
2. Touch the Rear VES soft-key to display the Rear VES soft-key at the top left of the left screen.

HDD In The MEDIA Column
Rear VES Soft-key
Dual Video Screen 3. To watch a DVD on Screen 1 for second row passen-
gers, ensure the Remote Control and Headphone switch
NOTE: Typically there are two different ways to operate
is on Channel 1.
the features of the Video Entertainment System (VES).
4. To watch a DVD on Screen 2 for third row passengers,
The Remote Control
ensure the Remote Control and Headphone switch is on
The Touch-Screen Radio (If Equipped) Channel 2.
Play A DVD Using The Touch-Screen Radio 4
1. Press the OPEN/CLOSE or LOAD hard-key on the
radio faceplate (Touch-Screen).
2. Insert the DVD with the label facing up. The radio
automatically selects the appropriate mode after the disc
is recognized and displays the menu screen or starts
playing the first track.
Using The Remote Control NOTE:
Channel/Screen 1 select mode information is shown
on the left side of the screen.
2. While looking at Screen 1 or 2, highlight DISC by
either pressing Up/Down/Left/Right buttons or by re-
on the right side of the screen.
peatedly pressing the MODE button, then press ENTER.
The VES will retain the last setting when turned off.
Using The Touch-Screen Radio Controls
2. Touch the Rear VES soft-key to display the Rear VES
Select DISC Mode On The VES Screen

Rear VES Soft-key Select Channel/Screen 1 And

3. Touch the 1 or 2 soft-key based on the channel you DISC In The MEDIA Column
want to change and then the DISC soft-key in the MEDIA NOTE:
column. To exit touch the back arrow at the top left of the To view a DVD on the radio press the RADIO/MEDIA
screen. hard-key, on the radio faceplate, then touch the DISC
tab soft-key and then the VIEW VIDEO soft-key.
Viewing a DVD on the Touch-Screen radio screen is NOTE: The VES player has basic DVD control func-
not available in all states/provinces, and the vehicle tion such as Menu, Play, Pause, FF, RW and Stop
must be stopped, and the shift lever must be in the
2. To watch a DVD on Screen 1 for second row passen-
PARK position for vehicles with automatic transmis-
gers, ensure the Remote Control and Headphone switch
sion. In vehicles with manual transmission the parking
is on Channel 1.
brake must be engaged.
3. To watch a DVD on Screen 2 for third row passengers,
Touching the screen on a Touch-Screen radio while a
ensure the Remote Control and Headphone switch is on
DVD is playing brings up basic remote control func-
Channel 2.
tions for DVD play such as scene selection, Play,
Pause, FF, RW, and Stop. Pressing the X in the upper Using The Remote Control
corner will turn off the remote control screen
functions.
2. While looking at Screen 1 or 2, highlight VES DISC by
Play A DVD Using The VES Player (If Equipped)
either pressing Up/Down/Left/Right buttons or by re-
1. Insert the DVD with the label facing up. The VES peatedly pressing the MODE button, then press ENTER
player automatically selects the appropriate mode after on the Remote Control.
the disc is recognized and starts playing the DVD.
Using The Touch-Screen Radio Controls
2. Touch the Rear VES soft-key to display the Rear VES
Controls. If a channel list is displayed, touch the HIDE
Select VES DISC Mode On The VES Screen

NOTE:
on the left side of the screen.
on the right side of the screen.
Rear VES Soft-key
The VES will retain the last setting when turned off.
3. Touch the 1 or 2 soft-key and then the DISC soft-key in NOTE:
the VES column. To exit touch the back arrow soft-key at To view a DVD on the radio press the RADIO/MEDIA
the top left of the screen. hard-key, on the radio faceplate, then touch the DISC
tab soft-key and then the VIEW VIDEO soft-key.
Viewing a DVD on the Touch-Screen radio screen is
not available in all states/provinces, and the vehicle
must be stopped, and the shift lever must be in the
PARK position for vehicles with automatic transmis-
sion. In vehicles with manual transmission the parking
brake must be engaged.
Listen To An Audio Source While A Video Is
Playing
Ensure the Remote Control and Headphone switch are on
the same channel. If watching a video on Screen 1
Select Channel/Screen 1 And DISC In The VES Column (second row), then Channel 2 could be used for audio. If
watching a video on Screen 2 (third row), then Channel 1
could be used for audio.
1. Press the MODE button on the Remote Control and
either the Mode Select Screen will display or a small
banner will appear at the bottom of the screen.
2. To listen to an audio source on Channel 1 or 2, either
press Up/Down/Left/Right on the Remote Control to
highlight the desired audio source or press the MODE 4
button repeatedly until the desired audio source appears
on the screen.
Select FM Mode On The VES screen

Using The Touch Screen Radio Controls 3. To listen to an audio source on Channel 1 while a
video is playing on Channel/Screen 2, touch the 1
soft-key and choose an audio source. To listen to an audio
2. Touch the Rear VES soft-key to display the Rear VES source on Channel 2 while a video is playing on
Controls. If a channel list is displayed, touch the HIDE Channel/Screen 1, touch the 2 soft-key and choose an
LIST soft-key to display the Rear VES Controls screen. audio source. To exit touch the back arrow soft-key at the
top left of the screen.
Rear VES Soft-key

Third Row Swivel Screen (If Equipped)
The third row screen or Screen 2 has the ability to
lower and swivel to face forward.
While the swivel screen is facing forward, the second
row screen or Screen 1 must be fully open in order for
the swivel screen (Screen 2) to work.
4

HDD In The MEDIA Column
Important Notes For Dual Video Screen System Remote Control
VES is able to transmit two channels of stereo audio
and video simultaneously.
In split screen mode the left side equates to Channel 1
and the right side equates to Channel 2.
Selecting a video source on Channel 1, the video
source will display on the second row screen or Screen
1 and can be heard on Channel 1.
Selecting a video source on Channel 2, the video
source will display on the third row screen or Screen 2
and can be heard on Channel 2
Remote Control
Audio can be heard through the headphones even
when the screen(s) are closed. Controls And Indicators
1. Power Turns the screen and wireless headphone
transmitter for the selected Channel on or off. To hear
audio while the screen is closed, press the Power button
to turn the headphone transmitter on.
2. Channel Selector Indicators When a button is 6. / Prev In radio modes, press to select to the
pressed, the currently affected channel or channel button previous station. In disc modes, press to advance to the
is illuminated momentarily. start of the current or previous audio track or video
chapter. In menu modes, use to navigate in the menu.
3. Light Turns the remote control backlighting on or off.
The remote backlighting turns off automatically after five 7. MENU Press to return to the main menu of a DVD
seconds. disc, to select a satellite audio channel from the Station
list, or select playback modes (SCAN/RANDOM for a
4. Channel/Screen Selector Switch - Indicates which
CD). 4
channel is being controlled by the remote control. When
the selector switch is in the Channel 1 position, the 8. / (Play/Pause) Begin/resume or pause disc play.
remote controls the functionality of headphone Channel
9. (Stop) Stops disc play
1 (right side of the screen). When the selector switch is in
the Channel 2, position the remote controls the function- 10. PROG Up/Down When listening to a radio mode,
ality of headphone Channel 2 (left side of the screen). pressing PROG Up selects the next preset and pressing
PROG Down selects the previous preset stored in the
5. In radio modes, press to seek the next tunable
radio. When listening to compressed audio on a data
station. In disc modes, press and hold to fast forward
disc, PROG Up selects the next directory and PROG
through the current audio track or video chapter. In
Down selects the previous directory. When listening to a
menu modes use to navigate in the menu.
disc in a radio with a multiple-disc changer, PROG Up and the disc is stopped, press the SETUP button to access
selects the next disc and PROG Down selects the previ- the DVD Setup menu. (see the DVD Setup Menu of this
ous disc. manual.)
11. MUTE Press to mute the headphone audio output 16. BACK When navigating in menu mode, press to
for the selected channel. return to the previous screen. When navigating a DVDs
disc menu, the operation depends on the discs contents.
12. SLOW Press to slow playback of a DVD disc. Press
play () to resume normal play. 17. In radio modes, press to seek to the previous
tunable station. In disc modes, press and hold to fast
13. STATUS Press to display the current status.
rewind through the current audio track or video chapter.
14. MODE Press to change the mode of the selected In menu modes use to navigate in the menu.
channel. See the Mode Selection section of this manual
18. ENTER Press to select the highlighted option in a
for details on changing modes.
menu.
15. SETUP When in a video mode, press the SETUP
19. / NEXT In radio modes, press to select to the
button to access the display settings (see the display
next station. In disc modes, press to advance to the next
settings section) to access the DVD setup menu, select the
audio track or video chapter. In menu modes, use to
menu button on the radio. When a disc is loaded in the
navigate in the menu.
DVD player (if equipped) and the VES mode is selected
Remote Control Storage
The video screen(s) come with a built in storage compart-
ment for the remote control which is accessible when the
screen is opened. To remove the remote, use your index
finger to pull and rotate the remote towards you. Do not
try to pull the remote straight down as it will be very
difficult to remove. To return the remote back into its
storage area, insert one long edge of the remote into the 4
two retaining clips first, and then rotate the remote back
up into the other two retaining clips until it snaps back
into position.
The Remote Control Storage

Locking The Remote Control
All remote control functionality can be disabled as a
parental control feature.
To disable the Remote Control from making any
changes, follow the radios instructions (select menu,
rear VES, lock). If the vehicle is not equipped with a
DVD player, follow the radios instructions to turn Headphones Operation
Video Lock on. The radio and the video screen(s) The headphones receive two separate channels of audio
indicate when Video Lock is active. using an infrared transmitter from the video screen.
Pressing the Video Lock again or turning the ignition Front seat occupants receive some headphone audio
OFF turns Video Lock OFF and allows remote control coverage to allow them to adjust the headphone volume
operation of the VES. for the young rear seat occupants that may not be able to
do so for themselves.
Replacing The Remote Control Batteries
The remote control requires two AAA batteries for op- If no audio is heard after increasing the volume control,
eration. To replace the batteries: verify that the screen is turned on and in the down
position and that the channel is not muted and the
Locate the battery compartment on the back of the
headphone channel selector switch is on the desired
remote, then slide the battery cover downward.
channel. If audio is still not heard, check that fully
Replace the batteries, making sure to orient them charged batteries are installed in the headphones.
according to the polarity diagram shown.
Replace the battery compartment cover.
Controls
The headphone power indicator and controls are located
on the right ear cup.
NOTE: The rear video system must be turned on before
sound can be heard from the headphones. To conserve
battery life, the headphones will automatically turn off
approximately three minutes after the rear video system
is turned off. 4
Changing the Audio Mode for Headphones
1. Ensure the Remote Control channel/screen selector
switch is in the same position as the headphone selector
1. Volume Control
2. Power Button switch..
3. Channel Selection Switch
4. Power Indicator NOTE:
When both switches are on Channel 1, the Remote is
controlling Channel 1 and the headphones are tuned
to the audio of the VES Channel 1.
When both switches are on Channel 2, the Remote is Replacing The Headphone Batteries
controlling Channel 2 and the headphones are tuned Each set of headphones requires two AAA batteries for
to the audio of the VES Channel 2. operation. To replace the batteries:
2. Press the MODE button on the remote control. Locate the battery compartment on the left ear cup of
the headphones, and then slide the battery cover
3. If the video screen is displaying a video source (such
downward.
as a DVD Video), pressing STATUS shows the status on a
popup banner at the bottom of the screen. Pressing the Replace the batteries, making sure to orient them
MODE button will advance to the next mode. When the according to the polarity diagram shown.
mode is in an audio only source (such as FM), the Mode
Replace the battery compartment cover.
Selection menu appears on screen.
Unwired Stereo Headphone Lifetime Limited
4. When the Mode Selection menu appears on screen,
Warranty
use the cursor buttons on the remote control to navigate
Who Does This Warranty Cover? This warranty covers
to the available modes and press the ENTER button to
the initial user or purchaser (you or your) of this
select the new mode.
particular Unwired Technology LLC (Unwired) wire-
5. To cancel out of the Mode Selection menu, press the less headphone (Product). The warranty is not transfer-
BACK button on the remote control. able.
How Long Does The Coverage Last? This warranty lasts NATURE WHATSOEVER. Some states and jurisdictions
as long as you own the Product. may not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not
What Does This Warranty Cover? Except as specified
apply to you. This warranty gives you specific legal
below, this warranty covers any Product that in normal
rights. You may also have other rights, which vary from
use is defective in workmanship or materials.
jurisdiction to jurisdiction.
What Does This Warranty Not Cover? This warranty What Will Unwired Do? Unwired, at its option, will
does not cover any damage or defect that results from repair or replace any defective Product. Unwired re- 4
misuse, abuse or modification of the Product other than serves the right to replace any discontinued Product with
by Unwired. Foam earpieces, which will wear over time a comparable model. THIS WARRANTY IS THE SOLE
through normal use, are specifically not covered (replace- WARRANTY FOR THIS PRODUCT, SETS FORTH YOUR
ment foam is available for a nominal charge). UNWIRED EXCLUSIVE REMEDY REGARDING DEFECTIVE
TECHNOLOGY IS NOT LIABLE FOR ANY INJURIES PRODUCTS, AND IS IN LIEU OF ALL OTHER WAR-
OR DAMAGES TO PERSONS OR PROPERTY RESULT- RANTIES (EXPRESS OR IMPLIED), INCLUDING ANY
ING FROM THE USE OF, OR ANY FAILURE OR DE- WARRANTY OR MERCHANTABILITY OR FITNESS
FECT IN, THE PRODUCT, NOR IS UNWIRED LIABLE FOR A PARTICULAR PURPOSE.
FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT,
INCIDENTAL, CONSEQUENTIAL, EXEMPLARY, PU- If you have any questions or comments regarding your
NITIVE OR OTHER DAMAGES OF ANY KIND OR Unwired wireless headphones, please phone 1-888-293-
3332 or email [email protected].
You may register your Unwired wireless headphones selected radio mode. When shared, the radio has priority
online at www.unwiredtechnology.com or by phone at over the VES or all radio modes (FM, AM, and SAT).
1-888-293-3332. The VES has the ability to switch tuner (AM/FM),
SEEK, SCAN, TUNE, and recall presets in radio modes as
System Information
long as it is not in shared mode.
Shared Modes
When in shared disc mode both the radio and the VES
This allows the VES to output radio sources to the
have control of the video functions. The VES has the
headphones and the radio to output VES sources to the
ability to control the following video modes:
vehicle speakers. When the radio and VES channel 1 or
2 are in the same (shared) mode, a VES icon will be 1. CD: Ability to Fast Forward, Rewind, Scan, and Track
visible on the radios display for that channel, and the Up/Down.
shared icon will be visible on the VES screen. When in
2. CD Changer (in radio): Ability to Disk Up/Down and
shared mode, the same audio source is heard in the
program all listed CD controls (Fast Forward, Rewind,
shared headphone channel 1 or channel 2.
Scan, and Track Up/Down).
If the radio functions (FM, AM, or SAT) are in the shared
The VES can even control radio modes or video modes
mode with the VES, only the radio is able to control the
while the radio is turned off. The VES can access the
radio functions. In this case, VES can share the radio
radio modes or disc modes by navigating to those modes
mode, but not change stations until the radio mode is
on the VES and activating a radio mode or disc mode.
changed to a mode that is different from the VES
Information Mode Display 3. Channel 1 Audio Only/Mute
4. Channel 2 Mode
5. Channel 2 Shared Status
6. Channel 2 Audio Only/Mute
7. Channel 1 ENTER Button Action
8. Channel 2 ENTER Button Action 4
9. Clock
10. Video Lock
11. Not Available / Error
Information Mode Video Screen Display 12. Disc Changer Status
1. Channel 1 Mode
2. Channel 1 Shared Status
Numeric Keypad Menu screen makes it easy to enter a specific tuner frequency,
satellite channel, or track number. To enter the desired
digit:
1. Press the remote controls navigation buttons (, ,
, ) to navigate to the desired digit.
2. When the digit is highlighted, press the remote con-
trols ENTER button to select the digit. Repeat these steps
until all digits are entered.
3. To delete the last digit, navigate to the Del button and
press the remote controls ENTER button.
4. After all of the digits are entered, navigate to the Go
Numeric Keypad Menu button and press the remote controls ENTER button.
When the display for either Channel 1 or Channel 2 Station List Menu
shows DIRECT TUNE, pressing the remote controls When listening to Satellite audio, pressing the remote
ENTER button activates a numeric keypad menu. This controls MENU button displays a list of all available
channels. Navigate this list using the remote controls
navigation buttons (, ) to find the desired station,
press the remote controls ENTER button to tune to that When listening to a CD Audio or CD Data disc, pressing
station. To jump through the list more quickly, navigate the remote controls MENU button displays a list of all
to the Page Up and Page Down icons on the screen. commands which control playback of the disc. Using the
options you can activate or cancel Scan play and Random
Disc Menu
play.
Display Settings
Disc Menu For CDs
Video Screen Display Settings

When watching a video source (DVD Video with the disc Listening To Audio With The Screen Closed
in Play mode, Aux Video, etc.), pressing the remote To listen to only audio portion of the channel with the
controls SETUP button activates the Display Settings screen closed:
menu. These settings control the appearance of the video
Set the audio to the desired source and channel.
on the screen. The factory default settings are already set
for optimum viewing, so there is no need to change these Close the video screen.
settings under normal circumstances.
To change the current audio mode, press the remote
To change the settings, press the remote controls navi- controls MODE button. This will automatically select
gation buttons (, ) to select an item, then press the the next available audio mode without using the Mode
remote controls navigation buttons (, ) to change the Select menu.
value for the currently selected item. To reset all values
When the screen is reopened, the video screen will
back to the original settings, select the Default Settings
automatically turn back on and show the appropriate
menu option and press the remote controls ENTER
display menu or media.
button.
If the screen is closed and there is no audio heard, verify
Disc Features control the remote DVD players (if
that the headphones are turned on (the ON indicator is
equipped) settings of DVD being watched in the remote
illuminated) and the headphone selector switch is on the
player.
desired channel. If the headphones are turned on, press
the remote controls power button to turn audio on. If DVD Region Codes
audio is still not heard, check that fully charged batteries
The VES DVD player and many DVD discs are coded
are installed in the headphones.
by geographic region. These region codes must match in
Disc Formats order for the disc to play. If the region code for the DVD
The VES DVD player is capable of playing the follow- disc does not match the region code for the player, the
ing types of discs (12 mm or 8 mm diameter): disc will not play and will be ejected.
DVD-Video discs (MPEG-2 video compression) (see DVD Audio Support 4
notes about DVD Region Codes)
When a DVD-Audio disc is inserted in the VES DVD
DVD-Audio discs (2 channel audio output only) player, the DVD-Audio title on the disc is played by
default (most DVD-Audio discs also have a Video title,
Audio Compact Discs (CDs)
but the Video title is ignored). All multi-channel program
CD Data discs with MP3 and WMA compressed audio material is automatically mixed down to two channels,
format files which may result in a lowered apparent volume level. If
you increase the volume level to account for this change
Video CDs (MPEG-1 video compression)
in level, remember to lower the volume before changing
the disc or to another mode.
Recorded Discs For CD Data (or CD-ROM) discs, always use the
ISO-9660 (Level 1 or Level 2), Joliet, or Romeo format.
The VES DVD player will play CD-R and CD-RW discs
Other formats (such as UDF, HFS, or others) are not
recorded in CD-Audio or Video-CD format, or as a
supported.
CD-ROM containing MP3 or WMA files. The player will
also play DVD-Video content recorded to a DVD-R or The player recognizes a maximum of 512 files and 99
DVD-RW disc. DVD-ROM discs (either pressed or re- folders per CD-R and CD-RW disc.
corded) are not supported.
Mixed media recordable DVD formats will only play
If you record a disc using a personal computer, there may the Video_TS portion of the disc.
be cases where the VES DVD player may not be able to
If you are still having trouble writing a disc that is
play some or the entire disc, even if it is recorded in a
playable in the VES DVD player, check with the disc
compatible format and is playable on other players. To
recording software publisher for more information about
help avoid playback problems, use the following guide-
burning playable discs.
lines when recording discs.
Open sessions are ignored. Only sessions that are The recommended method for labeling recordable discs
closed are playable. (CD-R, CD-RW, and DVD-R) is with a permanent marker.
Do not use adhesive labels as they may separate from the
For multi-session CDs that contain only multiple CD- disc, become stuck, and cause permanent damage to the
Audio sessions, the player will renumber the tracks so DVD player.
each track number is unique.
Compressed Audio Files (MP3 and WMA) Other compression formats such as AAC, MP3 Pro,
Ogg Vorbis, and ATRAC3 will not play. The DVD
The DVD player is capable of playing MP3 (MPEG-1
player will automatically skip the file and begin play-
Audio Layer 3) and WMA (Windows Media Audio) files
ing the next available file.
from a CD Data disc (usually a CD-R or CD-RW).
If you are creating your own files, the recommended
The DVD player always uses the file extension to
fixed bit rate for MP3 files is between 96 and 192Kbps
determine the audio format, so MP3 files must always
and the recommended fixed bit rate for WMA files is
end with the extension .mp3 or .MP3 and WMA 4
between 64 and 192Kbps. Variable bit rates are also
files must always end with the extension .wma or
supported. For both formats, the recommended
.WMA. To prevent incorrect playback, do not use
sample rate is either 44.1kHz or 48kHz.
these extensions for any other types of files.
To change the current file, use the remote controls or
For MP3 files, only version 1 ID3 tag data (such as
DVD players button to advance to the next file, or
artist name, track title, album, etc.) are supported.
the button to return to the start of the current or
Any file that is copy protected (such as those down- previous file.
loaded from many online music stores) will not play.
To change the current directory, use the remote con-
The DVD player will automatically skip the file and
trols PROG Up and Down buttons.
begin playing the next available file.
Disc Errors Display
If the DVD player is unable to read the disc, a Disc Error Other Language Setup
message is displayed on the VES and Radio displays
and the disc is automatically ejected. A dirty, damaged, or
incompatible disc format are all potential causes for a
Disc Error message.
If a disc has a damaged track which results in audible or
visible errors that persists for 2.0 seconds, the DVD
player will attempt to continue playing the disc by
skipping forward 1.0 to 3.0 seconds at a time. If the end
of the disc is reached, the DVD player will return to the
beginning of the disc and attempt to play the start of the
first track.
The DVD player may shut down during extremely hot
conditions, such as when the vehicles interior tempera-
ture is above 120F. When this occurs, the DVD player will
display VES High Temp and will shut off the VES
displays until a safe temperature is reached. This shut- DVD Player Language Menu
down is necessary to protect the optics of the DVD player.
All of the Language settings have a special Other setting Using the remote control Up and Down cursor but-
to accommodate languages other than Japanese or Eng- tons, select a digit for the current position. After
lish. These languages are selected using a special four- selecting the digit, press the remote controls Right
digit code. cursor button to select the next digit. Repeat this digit
selection sequence for all four digits.
To enter a new language code, activate the DVD Setup
Menu. To enter DVD Setup Menu stop the DVD, enter When the entire four-digit code is entered, press the
radio disc mode, then DVD setup and follow these remote controls ENTER button. If the language code
additional instructions: is not valid, the numbers all change back to *. If the 4
digits are visible after this step, then the language code
Using the remote control Up and Down cursor but-
is valid.
tons, highlight the Language item you want to edit,
and then press the remote control ENTER button. Here is an abbreviated list of language codes. For more
language codes, please contact the dealer where the
Using the remote control Down cursor button, select
vehicle was purchased.
the Other setting, then press the remote controls
Right cursor button to begin editing the setting. Language Code Language Code
Dutch 2311 French 1517
German 1304 Italian 1819
Portuguese 2519 Spanish 1418
Rating and Password Setup The default rating is Level 8 (play all discs without a
password) and the default password is 0000.
The Rating and Password settings work together to control
the types of DVDs that your family watches. Most DVD-
Video discs have a rating (from 1 to 8) assigned to them
where lower numbers are designated for all audiences and
higher numbers are designated for more adult audiences.
When a DVD-Video disc is loaded, its rating is compared
to the setting in the DVD player. If the rating of the disc
is higher than the setting in the player, a Password screen
is displayed. In order to watch the disc, the rear passen-
ger must enter the correct password using the password
entry method described below.
To play all discs without requiring a password, set the
DVD players rating to Level 8. Setting the rating to Level
1 always requires the password to play any DVD disc.
Not all DVD discs encode a Rating, so it is still possible
that discs designed for adult audiences can still play
without requiring a password. DVD Password Entry
To set the password, activate the DVD Setup Menu and After the four-digit password is entered, press the
follow these additional instructions: remote controls ENTER button to accept the change.
Using the remote control Left and Right cursor but-
tons, select the Rating tab.
Highlight Change Password, and then press the
remote controls ENTER button.
Enter the current password. Select a digit, use the 4
remote control Up and Down cursor buttons to set the
value for the current digit, and then press the remote
controls Right cursor button to select the next digit.
Repeat this digit selection sequence for all four digits.
After the four-digit password is entered, press the
remote controls ENTER button. If the password is
correct, the set password screen is displayed.
Using the remote controls Up and Down cursor
buttons to set the value for the current digit and the
remote controls Right cursor button to select digits, DVD Player Level Menu
enter the new password.
To set the rating, activate the DVD Setup Menu and Using the remote controls Up and Down cursor
follow these additional instructions: buttons, select the new rating level, and then press the
remote controls ENTER button to accept the change.
Using the remote controls Left and Right cursor
buttons, select the Rating tab. Product Agreement
This product incorporates copyright protection technol-
Highlight Change Rating, and then press the remote
ogy that is protected by U.S. patents and other intellec-
controls ENTER button.
tual property rights. Use of this copyright protection
Enter the current password. Select a digit, use the technology must be authorized by Macrovision, and is
remote controls Up and Down cursor buttons to set intended for home or other limited viewing uses other-
the value for the current digit, and then press the wise authorized by Macrovision. Reverse engineering or
remote controls Right cursor button to select the next disassembly is prohibited.
digit. Repeat this digit selection sequence for all four
Dolby Digital and MLP Lossless Manufactured
digits.
under license from Dolby Laboratories. Dolby,
After the four-digit password is entered, press the MLP Lossless, and the double-D symbol are trademarks
remote controls ENTER button. If the password is of Dolby Laboratories. Confidential unpublished works.
correct, the Rating Level menu is displayed. Copyright 1992-1997 Dolby Laboratories. All right re-
served.
General Information STEERING WHEEL AUDIO CONTROLS IF
EQUIPPED
This system complies with Part 15 of the FCC Operation
is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation. 4
Remote Sound System Controls

(Back View Of Steering Wheel)
The remote sound system controls are located on the rear
surface of the steering wheel, at the three and nine
oclock positions.
The right-hand rocker switch has a pushbutton in the The button located in the center of the left-hand switch
center, and controls the volume and mode of the sound will tune to the next preset station that you have pro-
system. Pressing the top of the rocker switch will increase grammed in the radio preset pushbutton.
the volume. Pressing the bottom of the rocker switch will
CD Player
decrease the volume. Pressing the center button changes
Pressing the top of the switch once will go to the next
the operation of the radio from AM to FM, or to CD
track on the CD. Pressing the bottom of the switch once
mode, depending on which radio is in the vehicle.
will go to the beginning of the current track, or to the
The left-hand rocker switch has a pushbutton in the beginning of the previous track if it is within one second
center. The function of the left-hand switch is different, after the current track begins to play.
depending on which mode you are in.
If you press the switch up or down twice it plays the
The following describes the left-hand rocker switch op- second track; three times, it will play the third, etc.
eration in each mode.
The button in the center of the left-hand switch has no
Radio Operation function in this mode.
Pressing the top of the switch will SEEK up for the next
listenable station, and pressing the bottom of the switch
will SEEK down for the next listenable station.
CD/DVD DISC MAINTENANCE NOTE: If you experience difficulty in playing a particu-
To keep a CD/DVD in good condition, take the following lar disc, it may be damaged (i.e., scratched, reflective
precautions: coating removed, a hair, moisture or dew on the disc)
oversized, or have protection encoding. Try a known
1. Handle the disc by its edge; avoid touching the
good disc before considering disc player service.
surface.
2. If the disc is stained, clean the surface with a soft cloth, RADIO OPERATION AND MOBILE PHONES
Under certain conditions, the mobile phone being on in
wiping from center to edge.
your vehicle can cause erratic or noisy performance from
4
3. Do not apply paper or tape to the disc; avoid scratch- your radio. This condition may be lessened or eliminated
ing the disc. by relocating the mobile phone antenna. This condition is
4. Do not use solvents such as benzene, thinner, cleaners, not harmful to the radio. If your radio performance does
or anti-static sprays. not satisfactorily clear by the repositioning of the
antenna, it is recommended that the radio volume be
5. Store the disc in its case after playing. turned down or off during mobile phone operation when
6. Do not expose the disc to direct sunlight. not using Uconnect (if equipped).
7. Do not store the disc where temperatures may become

too high.
CLIMATE CONTROLS The primary control for the rear blower is on the front
The Climate Control system allows you to regulate the climate control unit located on the instrument panel.
temperature, amount, and direction of air circulating When the front control is in any position other than rear,
throughout the vehicle. The controls are located on the the front control operates all the rear functions.
instrument panel, below the radio.
The rear airflow modes will mirror the front unit opera-
Manual Heating And Air Conditioning System tion. Rear Panel mode is automatically selected when the
If Equipped front control is in the Panel mode. When the front unit is
The controls for the manual system in this vehicle contain in Bi-Level mode, airflow will be emitted from both the
a series of outer rotary dials and inner push knobs. These upper and lower rear outlets. When the front control is in
comfort controls can be set to obtain desired interior Floor, Defrost, or Mix modes, airflow will be directed out
conditions. of the rear floor outlets.
With the Three-Zone Temperature Control system, each
front seat occupant can independently control the Heat-
ing, Ventilation, and Air Conditioning operations coming
from the outlets on their side of the vehicle.
2. Rear Blower Control If Equipped
Use this control to regulate the amount of air forced
through the rear system in any mode you select. The rear
blower speed increases as you move the control to the
right from the O (Off) position. There are seven blower
speeds. To allow the rear overhead control, turn blower
knob fully to the left, past The O off position.
3. Front Blower Control 4
Use this control to regulate the amount of air forced
through the system in any mode you select. The blower
speed increases as you move the control to the right from
Manual Temperature Control the O (Off) position. There are seven blower speeds.
1. Left Front Temperature Control NOTE: For vehicles equipped with Remote Start, the
Provides left front seat occupant with independent tem- climate controls will not function during Remote Start
perature control. Turn left for cooler or right for warmer operation if the blower control is left in the O (Off)
temperature settings. position. Blower control should be left in the ON
position to allow the climate control to either warm or
cool the vehicle.
4. Rear Temperature Control If Equipped 7. Front Defrost Mode
Provides temperature control for the rear cabin. Turn left Air is directed through the windshield and side
for cooler or right for warmer temperature settings in the window demist outlets. Use Defrost mode with
rear cabin. maximum blower and temperature settings for best
windshield and side window defrosting.
5. Right Front Temperature Control
Provides right front seat occupant with independent NOTE: The air conditioning compressor may operate in
temperature control. Turn left for cooler or right for Mix and Defrost, or a blend of these modes even if the
warmer temperature settings. A/C button is not pressed. This dehumidifies the air to
help dry the windshield. To improve fuel economy, use
6. Mix Mode
these modes only when necessary.
Air is directed through the floor, defrost and side
window demist outlets. This setting works best in 8. Electronic Rear Window Defrost
cold or snowy conditions that require extra heat at Press this button to turn on the rear window
the windshield. This setting is good for maintaining defroster and the heated outside mirrors (if
comfort, while reducing moisture on the windshield. equipped). An indicator in the button will illuminate
when the rear window defroster is on. The rear window
defroster automatically turns off after approximately
10 minutes. For an additional five minutes of operation,
press the button a second time.
NOTE:
CAUTION! (Continued)
You can turn off the heated mirror feature at anytime
by pressing the rear window defroster switch a second Do not use scrapers, sharp instruments, or abra-
time. sive window cleaners on the interior surface of the
window.
To prevent excessive battery drain, use the rear win- Keep all objects a safe distance from the window.
dow defroster only when the engine is operating.
9. Recirculation Control Button
CAUTION! Press this button to choose between outside air
4
Failure to follow these cautions can cause damage to intake or recirculation of the air inside the
the heating elements: vehicle. A lamp will illuminate when you are in
Use care when washing the inside of the rear Recirculation mode. Only use the Recirculation
window. Do not use abrasive window cleaners on mode to temporarily block out any outside odors, smoke,
the interior surface of the window. Use a soft cloth or dust, and to cool the interior rapidly upon initial
and a mild washing solution, wiping parallel to start-up in very hot or humid weather.
the heating elements. Labels can be peeled off
after soaking with warm water.
(Continued)
NOTE: In order to prevent fogging, when the Recirculation
If the Recirculation button is pressed when the system button is pressed and the mode control is set to Panel,
is in Defrost mode the Recirculation LED indicator will the A/C will engage automatically.
flash 3 times to indicate Recirculation mode is not
The A/C can be deselected manually without disturb-
allowed.
ing the mode control selection.
In Floor and Mix mode the system will turn off
10. Air Conditioning (A/C) Button
Recirculation mode after five minutes of operation.
Press and release to change the current setting.
You can select Recirculation mode again if desired.
The indicator illuminates when ON.
Continuous use of the Recirculation mode may make
the inside air stuffy and window fogging may occur.
Extended use of this mode is not recommended. NOTE: If your air conditioning performance seems
lower than expected, check the front of the A/C con-
In cold or damp weather, the use of the Recirculation
denser (located in front of the radiator), for an accumu-
mode will cause windows to fog on the inside because
lation of dirt or insects. Clean with a gentle water spray
of moisture buildup inside the vehicle. For maximum
from behind the radiator and through the condenser.
defogging, select the outside air position.
Fabric front fascia protectors may reduce airflow to the
condenser, reducing air conditioning performance.
11. Floor Mode Button NOTE: For maximum airflow to the rear, the center
Air is directed through the floor outlets with a instrument panel outlets can be directed toward the rear
small amount through the defrost and side window seat passengers.
demist outlets.
Economy Mode
12. Bi-Level Mode Button If ECONOMY mode is desired, press the A/C button to
Air is directed through the panel and floor outlets. turn off the indicator light and the A/C compressor.
Rotate the temperature control knob to the desired
4
NOTE: There is a difference in temperature (in any temperature.
conditions other than full cold or full hot), between the Max A/C
upper and lower outlets for added comfort. The warmer For maximum cooling use the A/C and Recirculation
air goes to the floor outlets. This feature gives improved mode buttons at the same time.
comfort during sunny but cool conditions.
Rear Manual Climate Control If Equipped
13. Panel Mode Button The Rear Manual Climate Control system has floor air
Air is directed through the outlets in the instrument outlets at the rear of the right side sliding door, and
panel. These outlets can be adjusted for direction, overhead outlets at each outboard rear seating position.
and turned on or off to control airflow. The unit provides warm or cool air through the floor and
upper outlets.
The rear blower and temperature controls for the rear Rear Blower Control
seat passengers are located in the headliner, near the The primary control for the rear blower is on the front
center of the vehicle. climate control unit, located on the instrument panel.
Only when the front control for the rear blower is in the
REAR position do the second row seat occupants have
control of the rear blower speed.
The rear blower control, located in the rear overhead
console, has an off position and a range of blower speeds.
This allows the second row seat occupants to control the
volume of air circulated in the rear of the vehicle.
Rear Manual Climate Controls

1 Rear Blower 3 Rear Mode
2 Rear Temperature 4 Rear Climate Control Lock
When rear controls are locked by the front system, the
CAUTION!
lock symbol on the temperature knob is illuminated, and
Interior air enters the Rear Manual Climate Control the rear overhead adjustments are inoperable.
system through an intake grille, located in the right
Rear Mode Control
side trim panel behind the third row seats. The
heater outlets are located in the right side trim panel, Headliner Mode
just behind the sliding door. Do not block or place Air comes from the outlets in the headliner. Each of
objects directly in front of the inlet grille or heater these outlets can be individually adjusted to direct 4
outlets. The electrical system could overload, causing the flow of air. Moving the air vanes of the outlets to one
damage to the blower motor. side will shut off the airflow.
Bi-Level Mode
Rear Temperature Control
Air comes from both the headliner outlets and the
The rear mode selection REAR, allows the settings to be
floor outlets.
controlled by the rear mode control knob.
NOTE: In many temperature positions, the Bi-Level
To change the temperature in the rear of the vehicle,
mode is designed to provide cooler air out of the head-
rotate the temperature control knob counterclockwise for
liner outlets and warmer air from the floor outlets.
cold air, and clockwise for heated air.
Floor Mode The Three-Zone ATC system automatically maintains the
Air comes from the floor outlets. interior comfort level desired by the driver and all passen-
gers. The system automatically adjusts the air temperature,
the airflow volume, amount of outside air recirculation and
Automatic Temperature Control (ATC) If
the airflow direction. This maintains a comfortable tem-
Equipped
perature, even under changing conditions.
Front Three-Zone ATC allows both driver and front
passenger seat occupant, and rear seat occupants to
select individual comfort settings.
When occupants in the vehicle select the AUTO mode
operation, a comfort temperature can be set by using
the temperature up and down buttons, and the auto
blower operation will be set automatically.
The system can be controlled manually, if desired.
SYNC feature links the controls for all three zones,
allowing one comfort setting (driver setting) for the
cabin, if desired.
Front ATC Panel
1. Air Conditioning (A/C) Button 7. Right Front Seat Occupant Temperature Display
Press and release to change the current Air Conditioning This display shows the temperature setting for the right
(A/C) setting, the indicator illuminates when A/C is ON. front seat occupant.
Performing this function will cause the ATC to switch
8. Front Defrost Button
into manual mode.
Press and release to change the current setting, the
2. Left Front Seat Occupant Temperature Display indicator illuminates when ON. Performing this function
This display shows the temperature setting for the left will cause the ATC to switch into manual mode. The
front seat occupant. blower will engage immediately if the Defrost mode is 4
selected.
3. Mode Display
This display shows the current Mode selection (Panel, 9. Passenger Temperature Control Up/Down Button
Bi-Level, Floor, Mix). Provides the passenger with independent temperature
control. Push the top button for warmer temperatures or
4. Blower Control Display
the lower button for cooler temperature settings.
This display shows the current Blower speed selection.
10. Rear Control Button
5. Front Auto Indicator
Provides toggle operation between front control screen
This indicates when the system is in Front Auto mode.
and rear control screen. Push the button to activate the
6. Auto Indicator rear climate control screen and allow the front seat
This indicates when the system is in Auto mode. occupants control over the rear climate settings.
11. Rear Lock 15. Mode Control Button
Press and release the Rear Lock button on the front ATC Press and release to select between Modes (Panel, Bi-
panel to lock and unlock the rear climate controls Level, Floor, Mix). Performing this function will cause the
ATC to switch into manual mode.
12. Auto Temperature Control Button
Controls airflow temperature, distribution, volume, and 16. Recirculation Control Button
the amount of air recirculation automatically. Press and Press and release to change the current setting, the
release to select. Refer to Automatic Operation for indicator illuminates when ON.
more information. Performing this function will cause
17. SYNC Button
the ATC to switch between manual mode and automatic
Press and release to control the temperature setting for all
modes.
three zones from the driver temperature control.
13. Climate Control OFF Button
18. Driver Temperature Control Up/Down Button
Press and release to turn the Climate Control OFF.
Provides the driver with independent temperature con-
14. Blower Control trol. Push the top button for warmer temperatures or the
There are seven blower speeds, the blower speed in- lower button for cooler temperature settings.
creases as you move the control to the right from the
lowest blower setting. Performing this function will
cause the ATC to switch into manual mode.
Controlling The Rear Climate Controls From The
Front ATC Panel
The Three-Zone ATC system allows for adjustment of the
rear climate controls from the front ATC panel.
To change the rear system settings:
1. Press REAR button to change control to rear control
mode, Rear display (below) will appear. Control func- 4
tions now operate rear system.
2. To return to Front screen, press REAR button again, or
it will revert to the Front screen after six seconds.
Front ATC Panel Rear Control Display
1. Mode Display
This display shows the current Mode selection.
2. Rear Temperature Display
This display shows the temperature setting for the rear
seat occupants.
3. Blower Control Display 3. When the system is set up for your comfort level, it is
This display shows the current Blower speed selection. not necessary to change the settings. You will experience
the greatest efficiency by simply allowing the system to
4. Rear Auto Indicator
function automatically.
This indicates when the system is in Rear Auto mode.
NOTE:
Automatic Operation
It is not necessary to move the temperature settings for
1. Press the AUTO button on the front ATC Panel and the cold or hot vehicles. The system automatically adjusts
words Front Auto will illuminate in the front ATC the temperature, mode and fan speed to provide
display, along with two temperatures for the driver and comfort as quickly as possible.
front passenger. The system will then automatically
The temperature can be displayed in English or Metric
regulate the amount of airflow.
units by selecting the Display Units of Measure in
2. Next, adjust the temperature you would like the customer-programmable feature. Refer to the Elec-
system to maintain, by adjusting the driver, front passen- tronic Vehicle Information Center (EVIC) Customer-
ger, and rear seat rotary temperature knobs. Once the Programmable Features in this Section.
desired temperature is displayed, the system will achieve
and automatically maintain that comfort level.
To provide you with maximum comfort in the automatic There are seven fixed blower speeds.
mode, during cold start-ups, the blower fan will remain Use the outer dial control to regulate
on low until the engine warms up. The fan will engage the amount of air forced through the
immediately if the Defrost mode is selected, or by chang- system in any mode you select. The
ing the front blower knob setting blower speed increases as you move
the control clockwise and decreases
Manual Operation
when you move the control counter-
This system offers a full complement of manual override Blower Control
features. The AUTO symbol in the front ATC display will
clockwise. 4
be turned off when the system is being used in the The blower fan speed can be set to any fixed speed by
manual mode. adjusting the blower control outer dial. The fan will now
operate at a fixed speed until additional speeds are
NOTE: Each of these features operate independently
selected. This allows the front occupants to control the
from each other. If any one feature is controlled manually,
volume of air circulated in the vehicle and cancel the
the temperature doors will continue to operate automati-
Auto mode.
cally.
The operator can also select the direction of the airflow
by selecting one of the following positions.
Panel Mode Floor Mode
Air is directed through the outlets in the instrument Air comes from the floor outlets. A slight amount of
panel. These outlets can be adjusted for direction, air is directed through the defrost and side window
and turned on or off to control airflow. demister outlets.
NOTE: For maximum airflow to the rear, the center Mix Mode
instrument panel outlets can be directed toward the rear Air comes from the floor, defrost and side window
seat passengers. demist outlets. This mode works best in cold or
snowy conditions. It allows you to stay comfort-
Bi-Level Mode
able, while keeping the windshield clear.
Air comes from the instrument panel outlets, floor
outlets and defrost outlets. A slight amount of air is Defrost Mode
also directed through the side window demister outlets. Air comes from the windshield and side window
demist outlets. Use Defrost mode with maximum
blower and temperature settings for best windshield and
mode is designed to provide cooler air out of the panel
side window defrosting.
outlets and warmer air from the floor outlets.
NOTE: While operating in the other modes, the system
will not automatically sense the presence of fog, mist or
ice on the windshield. Defrost mode must be manually
selected to clear the windshield and side glass.
Air Conditioning (A/C) Recirculation Control
The Air Conditioning (A/C) button allows the operator When outside air contains smoke, odors, or
to manually activate or deactivate the air conditioning high humidity, or if rapid cooling is desired,
system. When in A/C mode and the ATC is set to a cool you may wish to recirculate interior air by
temperature, dehumidified air flows through the air pressing the Recirculation control button. Re-
outlets. If Economy mode is desired, press the A/C circulation mode should only be used temporarily. A LED
button to turn off the A/C mode in the ATC display and will illuminate on the Recirculation control button when
deactivate the A/C system. Recirculation mode is selected. Push the button a second 4
time to turn off the Recirculation mode LED and allow
NOTE:
outside air into the vehicle.
If the system is in Mix, Floor or Defrost Mode, the A/C
can be turned off, but the A/C system shall remain NOTE: In cold weather, use of the Recirculation mode
active to prevent fogging of the windows. may lead to excessive window fogging. The Recirculation
mode is not allowed in Defrost mode to improve window
If fog or mist appears on the windshield or side glass,
clearing operation. Recirculation will be disabled auto-
select Defrost mode and increase blower speed.
matically if this mode is selected.
Rear Automatic Temperature Control (ATC) If The rear ATC system is located in the headliner, near the
Equipped center of the vehicle.
The rear ATC system has floor air outlets at the rear of the
right side sliding door, and overhead outlets at each
outboard rear seating position. The system provides
heated air through the floor outlets or cool, dehumidified
air through the headliner outlets.
The rear system temperature control is on the front ATC
panel located on the instrument panel.
Pressing the Rear Temperature Lock button on the front
ATC panel, illuminates a lock symbol in the rear display.
The rear temperature and air source are controlled from
the front ATC panel.
Rear ATC Control Features
Rear second row occupants can only adjust the rear ATC
1 - Blower Speed 3 - Rear Mode
control when the Rear Temperature Lock button is turned 2 - Rear Temperature 4 - Rear Temperature Lock
off.
1. Press the Rear Temperature Lock button on the front NOTE:
ATC panel. This turns off the Rear Temperature Lock icon It is not necessary to move the temperature settings for
in the rear temperature knob. cold or hot vehicles. The system automatically adjusts
the temperature, mode and fan speed to provide
2. Rotate the Rear Blower, Rear Temperature and the
comfort as quickly as possible.
Rear Mode Control knobs to suit your comfort needs.
The temperature can be displayed in English or Metric
3. ATC is selected by adjusting the rear blower knob
units by selecting the Display Units of Measure in
counterclockwise to AUTO.
customer-programmable feature. Refer to the Elec- 4
Once the desired temperature is displayed, the ATC tronic Vehicle Information Center (EVIC) Customer-
System will automatically achieve and maintain that Programmable Features in this Section.
comfort level. When the system is set up for your comfort
Rear Blower Control
level, it is not necessary to change the settings. You will
The rear blower control knob can be manually set to off,
experience the greatest efficiency by simply allowing the
or any fixed blower speed, by rotating the knob from low
system to function automatically.
to high. This allows the rear seat occupants to control the
volume of air circulated in the rear of the vehicle.
When rear controls are locked by the front system, the
CAUTION!
Rear Temperature Lock symbol on the temperature knob
Interior air enters the Rear Automatic Temperature is illuminated and any rear overhead adjustments are
Control System through an intake grille, located in ignored.
the right side trim panel behind the third row seats.
Rear Mode Control
The heater outlets are located in the right side trim
panel, just behind the sliding door. Do not block or Auto Mode
place objects directly in front of the inlet grille or The rear system automatically maintains the correct
heater outlets. The electrical system could overload mode and comfort level desired by the rear seat occu-
causing damage to the blower motor. pants.
Rear Temperature Control

To change the temperature in the rear of the vehicle,
rotate the temperature knob counterclockwise to lower
the temperature, and clockwise to increase the tempera-
ture. The rear temperature settings are displayed in the
front ATC panel.
Headliner Mode Floor Mode
Air comes from the outlets in the headliner. Each of Air comes from the floor outlets.
these outlets can be individually adjusted to direct
the flow of air. Moving the air vanes of the outlets to one
Summer Operation
side will shut off the airflow.
The engine cooling system in air conditioned vehicles
Bi-Level Mode must be protected with a high-quality antifreeze coolant
Air comes from both the headliner outlets and the to provide proper corrosion protection and to protect
floor outlets. against engine overheating. A solution of 50% ethylene 4
glycol antifreeze coolant and 50% water is recommended.
Refer to Maintenance Procedures in Maintaining Your
mode is designed to provide cooler air out of the head-
Vehicle for proper coolant selection.
liner outlets and warmer air from the floor outlets.
Winter Operation Window Fogging
To ensure the best possible heater and defroster perfor- Vehicle windows tend to fog on the inside in mild, rainy
mance, make sure the engine cooling system is function- and/or humid weather. To clear the windows, select
ing properly and the proper amount, type, and concen- Defrost or Mix mode and increase the front blower speed.
tration of coolant is used. Refer to Maintenance Do not use the Recirculation mode without A/C for long
Procedures in Maintaining Your Vehicle for proper periods, as fogging may occur.
coolant selection. Use of the air Recirculation mode
Outside Air Intake
during Winter months is not recommended, because it
Make sure the air intake, located directly in front of the
may cause window fogging.
windshield, is free of obstructions such as leaves. Leaves
Vacation/Storage collected in the air intake may reduce airflow, and if they
Before you store your vehicle, or keep it out of service enter the plenum they could plug the water drains. In
(i.e., vacation) for two weeks or more, run the air Winter months make sure the air intake is clear of ice,
conditioning system at idle for about five minutes, in slush and snow.
fresh air with the blower setting on high. This will ensure
adequate system lubrication to minimize the possibility
of compressor damage when the system is started again.
Operating Tips A/C Air Filter
On vehicles equipped with Automatic Temperature Con-
trol (ATC), the climate control system filters out dust and
pollen from the air. Refer to Air Conditioning in
Maintaining Your Vehicle for filter replacement
instructions.
4
STARTING AND OPERATING
CONTENTS
Starting Procedures . . . . . . . . . . . . . . . . . . . . 419 Automatic Transmission . . . . . . . . . . . . . . . . . 422
Automatic Transmission . . . . . . . . . . . . . . . 419 Key Ignition Park Interlock . . . . . . . . . . . . . 423
Normal Starting . . . . . . . . . . . . . . . . . . . . . 419 Brake/Transmission Shift Interlock System . . 424 5
Extreme Cold Weather Fuel Economy (Econ) Mode . . . . . . . . . . . . . 424
(Below 20F Or 29C) . . . . . . . . . . . . . . . . 420
Six-Speed Automatic Transmission . . . . . . . . 425
If The Engine Fails To Start . . . . . . . . . . . . . 420
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 426
After Starting . . . . . . . . . . . . . . . . . . . . . . . 421
Driving On Slippery Surfaces . . . . . . . . . . . . . 434
Engine Block Heater If Equipped . . . . . . . . 422
Acceleration . . . . . . . . . . . . . . . . . . . . . . . . 434
Traction . . . . . . . . . . . . . . . . . . . . . . . . . . . 435
416 STARTING AND OPERATING
Driving Through Water . . . . . . . . . . . . . . . . . 435 Tire Safety Information . . . . . . . . . . . . . . . . . 452
Flowing/Rising Water . . . . . . . . . . . . . . . . . 435 Tire Markings . . . . . . . . . . . . . . . . . . . . . . . 452
Shallow Standing Water . . . . . . . . . . . . . . . 436 Tire Identification Number (TIN) . . . . . . . . . 455
Power Steering . . . . . . . . . . . . . . . . . . . . . . . 437 Tire Terminology And Definitions . . . . . . . . . 456
Power Steering Fluid Check . . . . . . . . . . . . . 438 Tire Loading And Tire Pressure . . . . . . . . . . 457
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . 439 Tires General Information . . . . . . . . . . . . . 461
Anti-Lock Brake System (ABS) . . . . . . . . . . . . 441 Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . 461
Anti-Lock Brake Warning Light . . . . . . . . . . 443 Tire Inflation Pressures . . . . . . . . . . . . . . . . 462
Electronic Brake Control System . . . . . . . . . . . 443 Tire Pressures For High-Speed Operation . . . 463
Traction Control System (TCS) . . . . . . . . . . . 443 Radial-Ply Tires . . . . . . . . . . . . . . . . . . . . . 464
Brake Assist System (BAS) . . . . . . . . . . . . . . 444 Spare Tire Matching Original Equipped Tire
And Wheel If Equipped . . . . . . . . . . . . . . 464
Electronic Stability Control (ESC) . . . . . . . . . 445
Compact Spare Tire If Equipped . . . . . . . . 465
Hill Start Assist (HSA) . . . . . . . . . . . . . . . . 449
STARTING AND OPERATING 417
Full Size Spare If Equipped . . . . . . . . . . . . 466 Fuel Requirements . . . . . . . . . . . . . . . . . . . . . 482
Limited-Use Spare If Equipped . . . . . . . . . 466 3.6L Engine . . . . . . . . . . . . . . . . . . . . . . . . 482
Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . 467 Reformulated Gasoline . . . . . . . . . . . . . . . . 483
Tread Wear Indicators . . . . . . . . . . . . . . . . . 468 Gasoline/Oxygenate Blends . . . . . . . . . . . . . 483
Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . 468 E-85 Usage In Non-Flex Fuel Vehicles . . . . . . 484
Replacement Tires . . . . . . . . . . . . . . . . . . . . 469 MMT In Gasoline . . . . . . . . . . . . . . . . . . . . 485
Tire Chains . . . . . . . . . . . . . . . . . . . . . . . . . . 470 Materials Added To Fuel . . . . . . . . . . . . . . . 485 5
Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 472 Fuel System Cautions . . . . . . . . . . . . . . . . . 485
Tire Rotation Recommendations . . . . . . . . . . . 472 Carbon Monoxide Warnings . . . . . . . . . . . . 486
Tire Pressure Monitor System (TPMS) . . . . . . . 473 Flexible Fuel If Equipped . . . . . . . . . . . . . . 487
Base System . . . . . . . . . . . . . . . . . . . . . . . . 476 E-85 General Information . . . . . . . . . . . . . . . 487
Premium System If Equipped . . . . . . . . . . 478 Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . . . 488
Fuel Requirements . . . . . . . . . . . . . . . . . . . 488
Selection Of Engine Oil For Flexible Fuel Vehicle Loading . . . . . . . . . . . . . . . . . . . . . . 493
Vehicles (E-85) And Gasoline Vehicles . . . . . . 489
Vehicle Certification Label . . . . . . . . . . . . . . 493
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 490
Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . 495
Cruising Range . . . . . . . . . . . . . . . . . . . . . . 490
Common Towing Definitions . . . . . . . . . . . . 496
Replacement Parts . . . . . . . . . . . . . . . . . . . 490
Towing Tips . . . . . . . . . . . . . . . . . . . . . . . . 508
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 490
Recreational Towing
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 491 (Behind Motorhome, Etc.) . . . . . . . . . . . . . . . . 509
Fuel Filler Cap (Gas Cap) . . . . . . . . . . . . . . 491 Towing This Vehicle
Behind Another Vehicle . . . . . . . . . . . . . . . . 509
Loose Fuel Filler Cap Message . . . . . . . . . . . 492
STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust the
inside and outside mirrors, fasten your seat belt, and if Do not leave the key fob in or near the vehicle. A
present, instruct all other occupants to buckle their seat child could operate power windows, other con-
belts. trols, or move the vehicle.
WARNING! Automatic Transmission

The shift lever must be in the NEUTRAL or PARK
When leaving the vehicle, always remove the key position before you can start the engine. Press the brake
fob from the ignition and lock your vehicle. pedal before shifting into any driving gear.
5
Normal Starting
Allowing children to be in a vehicle unattended is 1. Do not press the accelerator.
dangerous for a number of reasons. A child or
2. Use the Fob with Integrated Key to briefly turn the
ignition switch to the START position and release it as
soon as the starter engages. The starter motor will
brake, brake pedal or the shift lever.
continue to run, and it will disengage automatically
(Continued) when the engine is running.
3. If the engine fails to start, the starter will disengage If The Engine Fails To Start
automatically in 10 seconds. If this occurs, turn the
ignition switch to the OFF position, wait 10 to 15 seconds, WARNING!
then repeat the Normal Starting procedure (Steps 13
Never pour fuel or other flammable liquids into
above).
the throttle body air inlet opening in an attempt to
NOTE: This vehicle is equipped with a transmission start the vehicle. This could result in a flash fire
shift interlocking system. The brake pedal must be causing serious personal injury.
pressed to shift out of PARK. Do not attempt to push or tow your vehicle to get
Extreme Cold Weather (Below 20F or 29C) it started. Vehicles equipped with an automatic
Follow the same instructions in the Normal Starting transmission cannot be started this way. Unburned
procedure. fuel could enter the catalytic converter and once
the engine has started, ignite and damage the
To ensure reliable starting at these temperatures, use of converter and vehicle.
an externally powered electric engine block heater (avail-
(Continued)
able from your authorized dealer) is recommended.
If the engine has been flooded, it may start to run, but not
have enough power to continue running when the key
If the vehicle has a discharged battery, booster fob is released. If this occurs, continue cranking with the
cables may be used to obtain a start from a booster accelerator pedal pushed all the way to the floor. Release
battery or the battery in another vehicle. This type the accelerator pedal and the key fob once the engine is
of start can be dangerous if done improperly. Refer running smoothly.
to Jump Starting in What To Do In Emergen-
cies for further information. If the engine shows no sign of starting after two 15
second intervals of cranking with the accelerator pedal
If the engine fails to start after you have followed the held to the floor, the Normal Starting procedure should
Normal Starting procedure, it may be flooded. Push be repeated.
5
the accelerator pedal all the way to the floor and hold it After Starting
there while cranking the engine. This should clear any The idle speed will automatically decrease as the engine
excess fuel in case the engine is flooded. warms up.
CAUTION!
To prevent damage to the starter, DO NOT crank the
engine for more than 15second intervals at one time.
Wait 10 to 15 seconds before trying again.
ENGINE BLOCK HEATER IF EQUIPPED AUTOMATIC TRANSMISSION
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a CAUTION!
standard 110-115 Volt AC electrical outlet with a
Damage to the transmission may occur if the follow-
grounded, three-wire extension cord.
ing precautions are not observed:
The engine block heater cord is routed under the hood on Move the shift lever into PARK only after the
the drivers side of the vehicle. It has a removable cap vehicle has come to a complete stop.
that is located on the driver side of the Integrated Power Shift into or out of REVERSE only after the
Module. vehicle has come to a complete stop and the engine
The engine block heater must be plugged in at least one is at idle speed.
hour to have an adequate warming effect on the engine. Do not move the shift lever between PARK, RE-
VERSE, NEUTRAL, or DRIVE when the engine is
WARNING! above idle speed.
Before moving the shift lever into any gear, make
Remember to disconnect the engine block heater sure your foot is firmly pressing the brake pedal.
cord before driving. Damage to the 110-115 Volt
electrical cord could cause electrocution. NOTE: You must press and hold the brake pedal down
while shifting out of PARK.

It is dangerous to move the shift lever out of PARK Unintended movement of a vehicle could injure
or NEUTRAL if the engine speed is higher than those in or near the vehicle. As with all vehicles,
idle speed. If your foot is not firmly pressing the you should never exit a vehicle while the engine is
brake pedal, the vehicle could accelerate quickly running. Before exiting a vehicle, always apply the
forward or in reverse. You could lose control of the parking brake, shift the transmission into PARK,
vehicle and hit someone or something. Only shift and remove the key fob. Once the key fob is
into gear when the engine is idling normally and removed, the shift lever is locked in the PARK
when your foot is firmly pressing the brake pedal. position, securing the vehicle against unwanted 5
movement. Furthermore, you should never leave
(Continued) unattended children inside a vehicle.
Key Ignition Park Interlock

This vehicle is equipped with a Key Ignition Park Inter-
lock which requires the shift lever to be placed in PARK
before the ignition switch can be turned to the LOCK/
OFF position. The key fob can only be removed from the
ignition when the ignition is in the LOCK/OFF position,
and once removed, the shift lever is locked in PARK.
This system prevents the key fob from being removed Fuel Economy (ECON) Mode
unless the shift lever is in PARK. The Fuel Economy (ECON) mode can improve the vehi-
cles overall fuel economy during normal driving condi-
NOTE: If a malfunction occurs, the system will trap the
tions. Press the econ switch in the center stack of the
key fob in the ignition cylinder to warn you that this
instrument panel and a green light will indicate the
safety feature is inoperable. The engine can be started
ECON mode is engaged.
and stopped but the key fob cannot be removed until you
obtain service.
Brake/Transmission Shift Interlock System
This vehicle is equipped with a Brake Transmission Shift
Interlock System (BTSI) that holds the shift lever in the
PARK position unless the brakes are applied. To move
the shift lever out of the PARK position, the ignition
switch must be turned to the ON/RUN position (engine
running or not) and the brake pedal must be pressed.
Fuel Economy Mode Switch

When the Fuel Economy (ECON) Mode is engaged, the Some ECON mode functions may be temporarily
vehicle control systems will change the following: inhibited based on temperature and other factors.
The transmission will upshift sooner and downshift Six-Speed Automatic Transmission
later. The shift lever position display (located in the instrument
panel cluster) indicates the transmission gear range. You
The transmission will skip select gears during shifts to
must press the brake pedal to move the shift lever out of
allow the engine to operate at lower speeds.
the PARK position (Refer to Brake/Transmission Shift
The torque converter clutch will engage at lower Interlock System in this section). To drive, move the shift
engine speeds and remain on longer. lever from PARK or NEUTRAL to the DRIVE position.
5
The engine idle speed will be lower.
The overall driving performance will be more conser-
vative.
The electronically-controlled transmission provides a Shifting from DRIVE to PARK or REVERSE should be
precise shift schedule. The transmission electronics are done only after the accelerator pedal is released and the
self-calibrating; therefore, the first few shifts on a new vehicle is stopped. Be sure to keep your foot on the brake
vehicle may be somewhat abrupt. This is a normal pedal when moving the shift lever between these gears.
condition, and precision shifts will develop within a few
The transmission shift lever has only PARK, REVERSE,
hundred miles (kilometers).
NEUTRAL, and DRIVE shift positions. Manual shifts can
be made using the Electronic Range Select (ERS) shift
control (described later in this section). Moving the shift
lever to the left or right (/ +) while in the DRIVE
position will select the highest available transmission
gear, and will display that gear in the instrument cluster
as 6, 5, 4, 3, 2, 1.
Gear Ranges
DO NOT race the engine when shifting from PARK or
NEUTRAL into another gear range.
Shift Lever
PARK
WARNING!
This range supplements the parking brake by locking the
transmission. The engine can be started in this range. Never use the PARK position as a substitute for
Never attempt to use PARK while the vehicle is in the parking brake. Always apply the parking
motion. Apply the parking brake when leaving the brake fully when parked to guard against vehicle
vehicle in this range. movement and possible injury or damage.
When parking on a level surface, you may place the shift Your vehicle could move and injure you and others
lever in the PARK position first, and then apply the if it is not completely in PARK. Check by trying to
parking brake. move the shift lever rearward (with the brake
pedal released) after you have placed it in PARK. 5
When parking on a hill, apply the parking brake before Make sure the transmission is in PARK before
placing the shift lever in PARK, otherwise the load on the leaving the vehicle.
transmission locking mechanism may make it difficult to
(Continued)
move the shift lever out of PARK. As an added precau-
tion, turn the front wheels toward the curb on a downhill
grade, and away from the curb on an uphill grade.
WARNING! (Continued) WARNING! (Continued)

It is dangerous to move the shift lever out of PARK Unintended movement of a vehicle could injure
or NEUTRAL if the engine speed is higher than those in or near the vehicle. As with all vehicles,
idle speed. If your foot is not firmly pressing the you should never exit a vehicle while the engine is
brake pedal, the vehicle could accelerate quickly running. Before exiting a vehicle, always apply the
forward or in reverse. You could lose control of the parking brake, shift the transmission into PARK,
vehicle and hit someone or something. Only shift and remove the key fob. Once the key fob is
into gear when the engine is idling normally and removed, the shift lever is locked in the PARK
your foot is firmly pressing the brake pedal. position, securing the vehicle against unwanted
(Continued) movement. Furthermore, you should never leave
unattended children inside a vehicle.
When leaving the vehicle, always remove the key
fob from the ignition and lock your vehicle.
(Continued)
WARNING! (Continued) CAUTION! (Continued)

Allowing children to be in a vehicle unattended is DO NOT race the engine when shifting from
dangerous for a number of reasons. A child or PARK or NEUTRAL into another gear range, as
others could be seriously or fatally injured. Chil- this can damage the drivetrain.
brake, brake pedal or the shift lever. The following indicators should be used to ensure that
Do not leave the key fob in or near the vehicle. A you have engaged the shift lever into the PARK position:
child could operate power windows, other con- When shifting into PARK, firmly move the shift lever
trols, or move the vehicle. all the way forward and to the left until it stops and is 5
fully seated.
CAUTION! Look at the shift lever position display and verify that
Before moving the shift lever out of PARK, you it indicates the PARK position.
must turn the ignition switch from the LOCK/OFF With brake pedal released, verify that the shift lever
position to the ON/RUN position, and also press will not move out of PARK.
the brake pedal. Otherwise, damage to the shift
lever could result.
(Continued)
REVERSE
CAUTION!
This range is for moving the vehicle backward. Shift into
REVERSE only after the vehicle has come to a complete Towing the vehicle, coasting, or driving for any other
stop. reason with the transmission in NEUTRAL can result
in severe transmission damage. Refer to Recre-
NEUTRAL
ational Towing in Starting And Operating and
Use this range when the vehicle is standing for prolonged
Towing A Disabled Vehicle in What To Do In
periods with engine running. The engine may be started
Emergencies for further information.
in this range. Set the parking brake and shift the trans-
mission into PARK if you must leave the vehicle.
DRIVE
This range should be used for most city and highway
WARNING!
driving. It provides the smoothest upshifts and down-
Do not coast in NEUTRAL and never turn off the shifts, and the best fuel economy. The transmission
ignition to coast down a hill. These are unsafe automatically upshifts through underdrive first, second,
practices that limit your response to changing traffic third, and fourth gears, direct fifth gear and overdrive
or road conditions. You might lose control of the sixth gear. The DRIVE position provides optimum driv-
vehicle and have a collision. ing characteristics under all normal operating conditions.
When frequent transmission shifting occurs (such as limited to third gear only. Normal operation will resume
when operating the vehicle under heavy loading condi- once the transmission temperature has risen to a suitable
tions, in hilly terrain, traveling into strong head winds, or level.
while towing heavy trailers), use the Electronic Range
Transmission Limp Home Mode
Select (ERS) shift control (described below) to select a
Transmission function is monitored electronically for
lower gear range. Under these conditions, using a lower
abnormal conditions. If a condition is detected that could
gear range will improve performance and extend trans-
result in transmission damage, Transmission Limp Home
mission life by reducing excessive shifting and heat
Mode is activated. In this mode, the transmission remains
buildup.
in third gear regardless of which forward gear is selected.
During cold temperatures, transmission operation may PARK, REVERSE, and NEUTRAL will continue to oper- 5
be modified depending on engine and transmission ate. The Malfunction Indicator Light (MIL) may be illu-
temperature as well as vehicle speed. This feature im- minated. Limp Home Mode allows the vehicle to be
proves warm up time of the engine and transmission to driven to an authorized dealer for service without dam-
achieve maximum efficiency. Engagement of the torque aging the transmission.
converter clutch is inhibited until the transmission fluid
In the event of a momentary problem, the transmission
is warm (refer to the Note under Torque Converter
can be reset to regain all forward gears by performing the
Clutch in this section). During extremely cold tempera-
following steps:
tures (-16F [-27C] or below), operation may briefly be
1. Stop the vehicle.
2. Shift the transmission into PARK. Electronic Range Select (ERS) Operation
The Electronic Range Select (ERS) shift control allows the
3. Turn the engine OFF.
driver to limit the highest available gear when the shift
4. Wait approximately 10 seconds. lever is in the DRIVE position. For example, if you shift
the transmission into 3 (third gear), the transmission will
5. Restart the engine.
never shift above third gear, but will shift down into
6. Shift into the desired gear range. If the problem is no second and first gear normally.
longer detected, the transmission will return to normal
You can switch between DRIVE and ERS mode at any
operation.
vehicle speed. When the shift lever is in the DRIVE
NOTE: Even if the transmission can be reset, we recom- position, the transmission will operate automatically,
mend that you visit your authorized dealer at your shifting between all available gears. Tapping the shift
earliest possible convenience. Your authorized dealer has lever to the left (-) will activate ERS mode, display the
diagnostic equipment to determine if the problem could current gear in the instrument cluster, and maintain that
recur. gear as the top available gear. Once in ERS mode, tapping
the shift lever to the left (-) or right (+) will change the top
If the transmission cannot be reset, authorized dealer
available gear.
service is required.
To exit ERS mode, simply press and hold the shift lever to Overdrive Operation
the right (+) until D is once again displayed in the shift The automatic transmission includes an electronically
lever position indicator in the instrument cluster. controlled Overdrive (sixth gear). The transmission will
automatically shift into the Overdrive gear if the follow-
WARNING! ing conditions are present:
Do not downshift for additional engine braking on a the shift lever is in the DRIVE position,
slippery surface. The drive wheels could lose their
the transmission fluid has reached an adequate tem-
grip and the vehicle could skid, causing an accident
perature,
or personal injury.
the engine coolant has reached an adequate tempera- 5
Odometer 1 2 3 4 5 6 D ture,
Screen Display
Actual Gear(s) 1 1-2 1-3 1-4 1-5 1-6 1-6 vehicle speed is sufficiently high, and
Allowed the driver is not heavily pressing the accelerator
NOTE: To select the proper gear position for maximum
deceleration (engine braking), tap the shift lever to the
left (-) repeatedly as the vehicle slows. The transmission
will shift to the range from which the vehicle can best be
slowed down.
Torque Converter Clutch DRIVING ON SLIPPERY SURFACES
A feature designed to improve fuel economy has been
Acceleration
included in the automatic transmission on your vehicle.
Rapid acceleration on snow covered, wet, or other slip-
A clutch within the torque converter engages automati-
pery surfaces may cause the driving wheels to pull
cally at calibrated speeds. This may result in a slightly
erratically to the right or left. This phenomenon occurs
different feeling or response during normal operation in
when there is a difference in the surface traction under
the upper gears. When the vehicle speed drops or during
the front (driving) wheels.
some accelerations, the clutch automatically disengages.
NOTE: The torque converter clutch will not engage WARNING!
until the transmission fluid and engine coolant are warm
Rapid acceleration on slippery surfaces is dangerous.
[usually after 1 to 3 miles (1.6 to 4.8 km) of driving].
Unequal traction can cause sudden pulling of the
Because the engine speed is higher when the torque
front wheels. You could lose control of the vehicle
converter clutch is not engaged, it may seem as if the
and possibly have a collision. Accelerate slowly and
transmission is not shifting into Overdrive when cold.
carefully whenever there is likely to be poor traction
This is normal. Using the Electronic Range Select (ERS)
(ice, snow, wet mud, loose sand, etc.).
feature, when the transmission is sufficiently warm, will
demonstrate that the transmission is able to shift into and
out of Overdrive.
Traction DRIVING THROUGH WATER
When driving on wet or slushy roads, it is possible for a Driving through water more than a few inches/
layer of water to build up between the tire and road centimeters deep will require extra caution to ensure
surface. This is known as hydroplaning and may cause safety and prevent damage to your vehicle.
partial or complete loss of vehicle control and stopping
Flowing/Rising Water
ability. To reduce this possibility, the following precau-
tions should be observed:
WARNING!
1. Slow down during rainstorms or when roads are
Do not drive on or across a road or path where water
slushy.
is flowing and/or rising (as in storm run-off). Flow- 5
2. Slow down if the road has standing water or puddles. ing water can wear away the road or paths surface
and cause your vehicle to sink into deeper water.
3. Replace the tires when tread wear indicators first
Furthermore, flowing and/or rising water can carry
become visible.
your vehicle away swiftly. Failure to follow this
4. Keep the tires properly inflated. warning may result in injuries that are serious or
fatal to you, your passengers, and others around you.
5. Maintain sufficient distance between your vehicle and
the vehicle in front of you to avoid a collision in a sudden
stop.
Shallow Standing Water
Although your vehicle is capable of driving through
shallow standing water, consider the following Caution Driving through standing water may cause dam-
and Warning before doing so. age to your vehicles drivetrain components. Al-
ways inspect your vehicles fluids (i.e., engine oil,
CAUTION! transmission, axle, etc.) for signs of contamination
(i.e., fluid that is milky or foamy in appearance)
Always check the depth of the standing water after driving through standing water. Do not con-
before driving through it. Never drive through tinue to operate the vehicle if any fluid appears
standing water that is deeper than the bottom of contaminated, as this may result in further dam-
the tire rims mounted on the vehicle. age. Such damage is not covered by the New
Determine the condition of the road or the path Vehicle Limited Warranty.
that is under water and if there are any obstacles in Getting water inside your vehicles engine can
the way before driving through the standing wa- cause it to lock up and stall out, and cause serious
ter. internal damage to the engine. Such damage is not
Do not exceed 5 mph (8 km/h) when driving covered by the New Vehicle Limited Warranty.
through standing water. This will minimize wave
effects.
(Continued)
POWER STEERING
WARNING!
The standard power steering system will give you good
Driving through standing water limits your vehi- vehicle response and increased ease of maneuverability
cles traction capabilities. Do not exceed 5 mph in tight spaces. The system will provide mechanical
(8 km/h) when driving through standing water. steering capability if power assist is lost.
Driving through standing water limits your vehi- If for some reason the power assist is interrupted, it will
cles braking capabilities, which increases stop- still be possible to steer your vehicle. Under these condi-
ping distances. Therefore, after driving through tions, you will observe a substantial increase in steering
standing water, drive slowly and lightly press on effort, especially at very low vehicle speeds and during
the brake pedal several times to dry the brakes. parking maneuvers. 5
Getting water inside your vehicles engine can
cause it to lock up and stall out, and leave you NOTE:
stranded. Increased noise levels at the end of the steering wheel
Failure to follow these warnings may result in travel are considered normal and do not indicate that
injuries that are serious or fatal to you, your there is a problem with the power steering system.
passengers, and others around you. Upon initial start-up in cold weather, the power steer-
ing pump may make noise for a short amount of time.
This is due to the cold, thick fluid in the steering
system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are
does not in any way damage the steering system. apparent, and/or the system is not functioning as antici-
pated. Coordinate inspection efforts through an autho-
WARNING! rized dealer.
Continued operation with reduced power steering CAUTION!
assist could pose a safety risk to yourself and others.
Service should be obtained as soon as possible. Do not use chemical flushes in your power steering
system as the chemicals can damage your power
steering components. Such damage is not covered by
CAUTION!
the New Vehicle Limited Warranty.
Prolonged operation of the steering system at the end
of the steering wheel travel will increase the steering WARNING!
fluid temperature and it should be avoided when
possible. Damage to the power steering pump may Fluid level should be checked on a level surface and
occur. with the engine off to prevent injury from moving
parts and to ensure accurate fluid level reading. Do
Power Steering Fluid Check not overfill. Use only manufacturers recommended
Checking the power steering fluid level at a defined power steering fluid.
service interval is not required. The fluid should only be
If necessary, add fluid to restore to the proper indicated
level. With a clean cloth, wipe any spilled fluid from all
surfaces. Refer to Fluids, Lubricants, and Genuine
Parts in Maintaining Your Vehicle for further
information.
PARKING BRAKE
Before leaving the vehicle, make sure that the parking
brake is fully applied and place the shift lever in the
PARK position. 5
The foot operated parking brake is positioned below the
lower left corner of the instrument panel. To apply the
Parking Brake
park brake, firmly push the park brake pedal fully. To
release the parking brake, press the park brake pedal a When the parking brake is applied with the ignition
second time and let your foot up as you feel the brake switch in the ON position, the Brake Warning Light in
disengage. the instrument cluster will illuminate.
NOTE:
WARNING!
When the parking brake is applied and the automatic
transmission is placed in gear, the Brake Warning When leaving the vehicle, always remove the key
Light will flash. If vehicle speed is detected, a chime fob from the ignition and lock your vehicle.
will sound to alert the driver. Fully release the parking Never leave children alone in a vehicle, or with
brake before attempting to move the vehicle. access to an unlocked vehicle.
This light only shows that the parking brake is ap- Allowing children to be in a vehicle unattended is
plied. It does not show the degree of brake application. dangerous for a number of reasons. A child or
When parking on a hill, it is important to turn the front dren should be warned not to touch the parking
wheels toward the curb on a downhill grade and away brake, brake pedal or the shift lever.
from the curb on an uphill grade. For vehicles equipped Do not leave the key fob in or near the vehicle, and
with an automatic transmission, apply the parking brake do not leave Keyless Enter-N-Go in the ACC or
before placing the shift lever in PARK, otherwise the load ON/RUN mode. A child could operate power win-
on the transmission locking mechanism may make it dows, other controls, or move the vehicle.
difficult to move the shift lever out of PARK. The parking
brake should always be applied whenever the driver is (Continued)
not in the vehicle.
ANTI-LOCK BRAKE SYSTEM (ABS)
The Anti-Lock Brake System (ABS) provides increased
Be sure the parking brake is fully disengaged vehicle stability and brake performance under most
before driving; failure to do so can lead to brake braking conditions. The system operates with a separate
failure and a collision. computer to modulate hydraulic pressure to prevent
Always fully apply the parking brake when leav- wheel lock-up and help avoid skidding on slippery
ing your vehicle, or it may roll and cause damage surfaces.
or injury. Also be certain to leave the transmission
in PARK. Failure to do so may allow the vehicle to ABS is activated during braking under certain road or
roll and cause damage or injury. stopping conditions. ABS-inducing conditions can in-
clude ice, snow, gravel, bumps, railroad tracks, loose 5
debris, or panic stops.
CAUTION!
You may experience the following when the brake system
If the Brake System Warning Light remains on with goes into anti-lock:
the parking brake released, a brake system malfunc-
tion is indicated. Have the brake system serviced by The ABS motor running (it may continue to run for a
an authorized dealer immediately. short time after the stop)
A clicking sound of solenoid valves
Brake pedal pulsations
A slight drop or fall away of the brake pedal at the end
of the stop
The Anti-Lock Brake System cannot prevent colli-
WARNING! sions, including those resulting from excessive
speed in turns, following another vehicle too
The Anti-Lock Brake System contains sophisti- closely, or hydroplaning.
cated electronic equipment that may be suscep- The capabilities of an ABS-equipped vehicle must
tible to interference caused by improperly in- never be exploited in a reckless or dangerous
stalled, or high output radio transmitting manner, which could jeopardize the users safety
equipment. This interference can cause possible or the safety of others.
loss of anti-lock braking capability. Installation of
such equipment should be performed by qualified All vehicle wheels and tires must be the same size and
professionals. type, and tires must be properly inflated to produce
Pumping of the Anti-Lock Brakes will diminish accurate signals for the computer.
their effectiveness and may lead to a collision.
Pumping makes the stopping distance longer. Just
press firmly on your brake pedal when you need
to slow down or stop.
(Continued)
Anti-Lock Brake Warning Light If both the Brake Warning Light and the Anti-Lock
The Anti-Lock Brake Warning Light moni- Brake Warning Light remain on, the ABS and Electronic
tors the anti-lock brake system. The light will Brake Force Distribution (EBD) systems are not function-
come on when the ignition switch is turned to ing. Immediate repair to the ABS system is required.
the ON position and may stay on for as long as Consult with your authorized dealer service center as
four seconds. soon as possible.
If the Anti-Lock Brake Warning Light remains on or ELECTRONIC BRAKE CONTROL SYSTEM
comes on while driving, it indicates that the anti-lock Your vehicle is equipped with an advanced electronic
portion of the brake system is not functioning and that brake control system that includes the Traction Control
service is required. However, the conventional brake 5
System (TCS), Brake Assist System (BAS) and Electronic
system will continue to operate normally if the Brake Stability Control (ESC), and Hill Start Assist (HSA).
Warning Light is not on. These systems complement the Anti-Lock Brake System
If the Anti-Lock Brake Warning Light is on, the brake (ABS) by optimizing the vehicle braking capability dur-
system should be serviced as soon as possible to restore ing emergency braking maneuvers.
the benefits of anti-lock brakes. If the Anti-Lock Brake Traction Control System (TCS)
Warning Light does not come on when the ignition The Traction Control System (TCS) monitors the amount
switch is turned to the ON position, have the bulb of wheel spin of each of the driven wheels. If wheel spin
repaired as soon as possible. is detected, brake pressure is applied to the slipping
wheel(s) and engine power is reduced, to provide en-
WARNING!
hanced acceleration and stability. A feature of the TCS
functions similarly to a limited-slip differential, and The TCS cannot prevent the natural laws of phys-
controls the wheel spin across a driven axle. If one wheel ics from acting on the vehicle, nor can it increase
on a driven axle is spinning faster than the other, the the traction afforded.
system will apply the brake of the spinning wheel. This The TCS cannot prevent collisions, including
will allow more engine torque to be applied to the wheel those resulting from excessive speed in turns, or
that is not spinning. This feature remains active even if hydroplaning.
the ESC is in the Partial Off mode. The capabilities of a TCS-equipped vehicle must
The ESC Activation/Malfunction Indicator Light (in never be exploited in a reckless or dangerous
the instrument cluster) will start to flash as soon as the manner, which could jeopardize the users safety
tires lose traction and the wheels begin to spin. This or the safety of others.
indicates that the TCS is active. If the indicator light
flashes during acceleration, ease up on the accelerator Brake Assist System (BAS)
and apply as little throttle as possible. Be sure to adapt The Brake Assist System (BAS) is designed to optimize
your speed and driving to the prevailing road conditions, the vehicles braking capability during emergency brak-
and do not switch off the ESC or TCS. ing maneuvers. The system detects an emergency brak-
ing situation by sensing the rate and amount of brake
application, and then applies optimum pressure to the
brakes. This can help reduce braking distances. The BAS
complements the ABS. Applying the brakes very quickly
results in the best BAS assistance. To receive the benefit of The capabilities of a BAS-equipped vehicle must
the system, you must apply continuous braking pressure never be exploited in a reckless or dangerous
during the stopping sequence. Do not reduce brake pedal manner which could jeopardize the users safety
pressure unless braking is no longer desired. Once the or the safety of others.
brake pedal is released, the BAS is deactivated.
Electronic Stability Control (ESC)
WARNING! The Electronic Stability Control (ESC) enhances direc-
tional control and stability of the vehicle under various
The BAS cannot prevent the natural laws of phys- driving conditions. ESC corrects for over/under steering
5
ics from acting on the vehicle, nor can it increase of the vehicle by applying the brake of the appropriate
the traction afforded by prevailing road condi- wheel to assist in counteracting the over/under steer
tions. condition. Engine power may also be reduced to help the
The BAS cannot prevent collisions, including vehicle maintain the desired path.
those resulting from excessive speed in turns,
driving on very slippery surfaces, or hydroplan-
ing.
(Continued)
ESC uses sensors in the vehicle to determine the vehicle
path intended by the driver and compares it to the actual
path of the vehicle. When the actual path does not match ESC cannot prevent accidents, including those
the intended path, ESC applies the brake of the appro- resulting from excessive speed in turns, driving on
priate wheel to assist in counteracting the oversteer or very slippery surfaces, or hydroplaning. ESC also
understeer condition. cannot prevent accidents resulting from loss of
vehicle control due to inappropriate driver input
Oversteer - when the vehicle is turning more than for the conditions. Only a safe, attentive, and
appropriate for the steering wheel position. skillful driver can prevent accidents.
Understeer - when the vehicle is turning less than The capabilities of an ESC equipped vehicle must
appropriate for the steering wheel position. never be exploited in a reckless or dangerous
manner which could jeopardize the users safety
WARNING! or the safety of others.
The Electronic Stability Control (ESC) cannot pre- ESC Operating Modes
vent the natural laws of physics from acting on the The ESC Off switch is located in the center
vehicle, nor can it increase the traction afforded by switch bank, next to the hazard flasher switch.
prevailing road conditions.
(Continued)
ESC On again, momentarily press the ESC Off switch. This will
This mode is the normal operating mode for ESC on restore the normal ESC On mode of operation.
two-wheel drive vehicles. Whenever the vehicle is
NOTE: To improve the vehicles traction when driving
started, the ESC system will be in this mode. This mode
with snow chains, or starting off in deep snow, sand or
should be used for most driving situations. ESC should
gravel, it may be desirable to switch to the Partial Off
only be turned off for specific reasons as noted below.
mode by pressing the ESC Off switch. Once the situa-
ESC Partial Off tion requiring ESC to be switched to the Partial Off
This mode is entered by momentarily pressing the ESC mode is overcome, turn ESC back on by momentarily
Off switch. pressing the ESC Off switch. This may be done while
the vehicle is in motion. 5
When in the Partial Off mode, the TCS portion of ESC,
except for the limited slip feature described in the TCS
WARNING!
section, has been disabled and the ESC Activation/
Malfunction Indicator Light will be illuminated. When In partial ESC mode, the engine power reduction
in the Partial Off mode, ESC will operate without feature of ESC is disabled. Therefore, enhanced
engine torque management. This mode is intended to be vehicle stability offered by the ESC system is re-
used if the vehicle is in deep snow, sand or gravel duced.
conditions and more wheel spin than ESC would nor-
mally allow is required to gain traction. To turn ESC on
ESC Activation/Malfunction Indicator Light And Malfunction Indicator Light begins to flash during ac-
ESC OFF Indicator Light celeration, ease up on the accelerator and apply as little
The ESC Activation/Malfunction Indicator throttle as possible. Be sure to adapt your speed and
Light in the instrument cluster will come on driving to the prevailing road conditions.
when the ignition switch is turned to the ON
NOTE:
position. It should turn off with the engine
The ESC Activation/Malfunction Indicator Light
running. If the ESC Activation/Malfunction Indicator
and the ESC OFF Indicator Light come on momen-
Light comes on continuously with the engine running, a
tarily each time the ignition switch is turned ON.
malfunction has been detected in the ESC system. If this
light remains on after several ignition cycles, and the Each time the ignition is turned ON, the ESC system
vehicle has been driven several miles (kilometers) at will be ON even if it was turned off previously.
speeds greater than 30 mph (48 km/h), see your autho-
The ESC system will make buzzing or clicking sounds
rized dealer as soon as possible to have the problem
when it is active. This is normal; the sounds will stop
diagnosed and corrected.
when ESC becomes inactive following the maneuver
The ESC Activation/Malfunction Indicator Light (lo- that caused the ESC activation.
cated in the instrument cluster) starts to flash as soon as
The ESC OFF Indicator Light indicates the
the tires lose traction and the ESC system becomes active.
Electronic Stability Control (ESC) is off.
The ESC Activation/Malfunction Indicator Light also
flashes when TCS is active. If the ESC Activation/
Hill Start Assist (HSA) Gear selection matches vehicle uphill direction (i.e.,
The HSA system is designed to assist the driver when vehicle facing uphill is in forward gear; vehicle back-
starting a vehicle from a stop on a hill. HSA will maintain ing uphill is in REVERSE gear).
the level of brake pressure the driver applied for a short
HSA will work in REVERSE and all forward gears when
period of time after the driver takes their foot off of the
the activation criteria have been met. The system will not
brake pedal. If the driver does not apply the throttle
activate if the vehicle is placed in NEUTRAL or PARK.
during this short period of time, the system will release
brake pressure and the vehicle will roll down the hill. The
WARNING!
system will release brake pressure in proportion to the
amount of throttle applied as the vehicle starts to move in There may be situations on minor hills (i.e., less than 5
the intended direction of travel. 8%), with a loaded vehicle, or while pulling a trailer,
when the system will not activate and slight rolling
HSA Activation Criteria
may occur. This could cause a collision with another
The following criteria must be met in order for HSA to
vehicle or object. Always remember the driver is
activate:
responsible for braking the vehicle.
Vehicle must be stopped.
Vehicle must be on a 6% (approximate) grade or
greater hill.
Disabling/Enabling HSA 5. Release the clutch pedal.
If you wish to turn on or off the HSA system, it can be
6. Rotate the steering wheel one-half turn to the left.
done using the Customer Programmable Features in the
Electronic Vehicle Information Center (EVIC). Refer to 7. Press the ESC Off switch (located in the lower
Electronic Vehicle Information Center (EVIC) in Un- switch bank below the climate controls) four times within
derstanding Your Instrument Panel for further informa- 20 seconds. The ESC Activation/Malfunction Indicator
tion. Light should turn on and turn off two times.
For vehicles not equipped with the EVIC, perform the 8. Rotate the steering wheel back to center and then an
following steps: additional half-turn to the right.
NOTE: You must complete Steps 1 through 8 within 9. Turn the ignition switch to the OFF position and then
90 seconds. back to the ON position. If the sequence was completed
properly, the ESC Activation/Malfunction Indicator
1. Center the steering wheel (front wheels pointing
Light will blink several times to confirm HSA is dis-
straight forward).
abled.
2. Shift the transmission into NEUTRAL.
10. Repeat these steps if you want to return this feature
3. Apply the parking brake. to its previous setting.
4. Start the engine.
Towing With HSA
HSA will provide assistance when starting on a grade
when pulling a trailer. HSA is not a parking brake. Always apply the
parking brake fully when leaving your vehicle.
WARNING! Also, be certain to leave the transmission in PARK.
Failure to follow these warnings may cause the
If you use a trailer brake controller with your vehicle to roll down the incline and could collide
trailer, your trailer brakes may be activated and with another vehicle, object or person, and cause
deactivated with the brake switch. If so, when the serious or fatal injury. Always remember to use the
brake pedal is released, there may not be enough parking brake while parking on a hill and that the
brake pressure to hold the vehicle and trailer on a
5
driver is responsible for braking the vehicle.
hill and this could cause a collision with another
vehicle or object behind you. In order to avoid HSA Off
rolling down the hill while resuming acceleration, If you wish to turn off the HSA system, it can be done
manually activate the trailer brake prior to releas- using the Customer Programmable Features in the Elec-
ing the brake pedal. Always remember the driver tronic Vehicle Information Center (EVIC). Refer to Elec-
is responsible for braking the vehicle. tronic Vehicle Information Center (EVIC) in Under-
(Continued) standing Your Instrument Panel for further information.
TIRE SAFETY INFORMATION NOTE:
P (Passenger) - Metric tire sizing is based on U.S.
Tire Markings
design standards. P-Metric tires have the letter P
molded into the sidewall preceding the size designa-
tion. Example: P215/65R15 95H.
European-Metric tire sizing is based on European
design standards. Tires designed to this standard have
the tire size molded into the sidewall beginning with
the section width. The letter P is absent from this tire
size designation. Example: 215/65R15 96H.
LT (Light Truck) - Metric tire sizing is based on U.S.
design standards. The size designation for LT-Metric
tires is the same as for P-Metric tires except for the
letters LT that are molded into the sidewall preced-
1 U.S. DOT Safety 4 Maximum Load
Standards Code (TIN) ing the size designation. Example: LT235/85R16.
2 Size Designation 5 Maximum Pressure
3 Service Description 6 Treadwear, Traction and Temporary spare tires are spares designed for tempo-
Temperature Grades rary emergency use only. Temporary high pressure
compact spare tires have the letter T or S molded High flotation tire sizing is based on U.S. design
into the sidewall preceding the size designation. Ex- standards and it begins with the tire diameter molded
ample: T145/80D18 103M. into the sidewall. Example: 31x10.5 R15 LT.
Tire Sizing Chart
EXAMPLE:
Size Designation:
P = Passenger car tire size based on U.S. design standards
....blank.... = Passenger car tire based on European design standards
LT = Light truck tire based on U.S. design standards
T or S = Temporary spare tire
5
31 = Overall diameter in inches (in)
215 = Section width in millimeters (mm)
65 = Aspect ratio in percent (%)
Ratio of section height to section width of tire
10.5 = Section width in inches (in)
R = Construction code
R means radial construction
D means diagonal or bias construction
15 = Rim diameter in inches (in)
EXAMPLE:
Service Description:
95 = Load Index
A numerical code associated with the maximum load a tire can carry
H = Speed Symbol
A symbol indicating the range of speeds at which a tire can carry a load corresponding
to its load index under certain operating conditions
The maximum speed corresponding to the speed symbol should only be achieved under
specified operating conditions (i.e., tire pressure, vehicle loading, road conditions, and
posted speed limits)
Load Identification:
....blank.... = Absence of any text on the sidewall of the tire indicates a Standard Load (SL) tire
Extra Load (XL) = Extra load (or reinforced) tire
Light Load (LL) = Light load tire
C, D, E, F, G = Load range associated with the maximum load a tire can carry at a specified pressure
Maximum Load Maximum load indicates the maximum load this tire is designed to carry
Maximum Pressure Maximum pressure indicates the maximum permissible cold tire inflation pressure for
this tire
Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall
The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on
however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard
with white sidewalls will have the full TIN, including the side of the tire.
date code, located on the white sidewall side of the tire.
EXAMPLE:
DOT MA L9 ABCD 0301
DOT = Department of Transportation
This symbol certifies that the tire is in compliance with the U.S. Department of Transportation tire
safety standards and is approved for highway use 5
MA = Code representing the tire manufacturing location (two digits)
L9 = Code representing the tire size (two digits)
ABCD = Code used by the tire manufacturer (one to four digits)
03 = Number representing the week in which the tire was manufactured (two digits)
03 means the 3rd week.
01 = Number representing the year in which the tire was manufactured (two digits)
01 means the year 2001
Prior to July 2000, tire manufacturers were only required to have one number to represent the
year in which the tire was manufactured. Example: 031 could represent the 3rd week of 1981 or 1991
Tire Terminology And Definitions
Term Definition
B-Pillar The vehicle B-Pillar is the structural member of the body located
behind the front door.
Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the
vehicle has not been driven for at least 3 hours, or driven less
than 1 mile (1.6 km) after sitting for a three hour period. Inflation
pressure is measured in units of PSI (pounds per square inch) or
kPa (kilopascals).
Maximum Inflation Pressure The maximum inflation pressure is the maximum permissible cold
tire inflation pressure for this tire. The maximum inflation pres-
sure is molded into the sidewall.
Recommended Cold Tire Inflation Vehicle manufacturers recommended cold tire inflation pressure
Pressure as shown on the tire placard.
Tire Placard A paper label permanently attached to the vehicle describing the
vehicles loading capacity, the original equipment tire sizes and
the recommended cold tire inflation pressures.
Tire Loading And Tire Pressure Tire And Loading Information Placard
Tire And Loading Information Placard Location
NOTE: The proper cold tire inflation pressure is listed
on the drivers side B-Pillar or the rear edge of the
drivers side door.
Tire and Loading Information Placard
Tire Placard Location

This placard tells you important information about axles must not be exceeded. For further information on
the: GAWRs, vehicle loading, and trailer towing, refer to
1) number of people that can be carried in the vehicle Vehicle Loading in this section.
2) total weight your vehicle can carry To determine the maximum loading conditions of your
3) tire size designed for your vehicle vehicle, locate the statement The combined weight of
4) cold tire inflation pressures for the front, rear, and occupants and cargo should never exceed XXX lbs or
spare tires. XXX kg on the Tire and Loading Information placard.
The combined weight of occupants, cargo/luggage and
Loading
trailer tongue weight (if applicable) should never exceed
The vehicle maximum load on the tire must not exceed
the weight referenced here.
the load carrying capacity of the tire on your vehicle. You
will not exceed the tires load carrying capacity if you Steps For Determining Correct Load Limit
adhere to the loading conditions, tire size, and cold tire
1. Locate the statement The combined weight of occu-
inflation pressures specified on the Tire and Loading
pants and cargo should never exceed XXX lbs or XXX kg
Information placard and in the Vehicle Loading section
on your vehicles placard.
of this manual.
2. Determine the combined weight of the driver and
NOTE: Under a maximum loaded vehicle condition,
passengers that will be riding in your vehicle.
gross axle weight ratings (GAWRs) for the front and rear
3. Subtract the combined weight of the driver and pas- NOTE:
sengers from XXX lbs or XXX kg. The following table shows examples on how to calcu-
late total load, cargo/luggage, and towing capacities
4. The resulting figure equals the available amount of
of your vehicle with varying seating configurations
cargo and luggage load capacity. For example, if XXX
and number and size of occupants. This table is for
amount equals 1,400 lbs (635 kg) and there will be five
illustration purposes only and may not be accurate for
150 lb (68 kg) passengers in your vehicle, the amount of
the seating and load carry capacity of your vehicle.
available cargo and luggage load capacity is 650 lbs
(295 kg) (since 5 x 150 = 750, and 1400 750 = 650 lbs For the following example, the combined weight of
[295 kg]). occupants and cargo should never exceed 865 lbs
(392 kg). 5
5. Determine the combined weight of luggage and cargo
being loaded on the vehicle. That weight may not safely
exceed the available cargo and luggage load capacity
calculated in Step 4.
6. If your vehicle will be towing a trailer, load from your
trailer will be transferred to your vehicle. Consult this
manual to determine how this reduces the available
cargo and luggage load capacity of your vehicle.
Safety
WARNING!
Overloading of your tires is dangerous. Overloading WARNING!
can cause tire failure, affect vehicle handling, and
Improperly inflated tires are dangerous and can
increase your stopping distance. Use tires of the
cause collisions.
recommended load capacity for your vehicle. Never
Under-inflation increases tire flexing and can re-
overload them.
sult in over-heating and tire failure.
Over-inflation reduces a tires ability to cushion
TIRES GENERAL INFORMATION
shock. Objects on the road and chuckholes can 5
Tire Pressure cause damage that result in tire failure.
Proper tire inflation pressure is essential to the safe and Over-inflated or under-inflated tires can affect
satisfactory operation of your vehicle. Three primary vehicle handling and can fail suddenly, resulting
areas are affected by improper tire pressure. in loss of vehicle control.
Unequal tire pressures can cause steering prob-
lems. You could lose control of your vehicle.
(Continued)
Tire Inflation Pressures
The proper cold tire inflation pressure is listed on the
Unequal tire pressures from one side of the ve- drivers side B Pillar or rear edge of the drivers side
hicle to the other can cause the vehicle to drift to door.
the right or left.
Always drive with each tire inflated to the recom- The tire pressure should be checked and adjusted, and
mended cold tire inflation pressure. the tires inspected for signs of wear or visible damage, at
least once a month. Use a good quality pocket-type gauge
Economy to check tire pressure. Do not make a visual judgement
Improper inflation pressures can cause uneven wear when determining proper inflation. Radial tires may look
patterns to develop across the tire tread. These abnormal properly inflated, even when they are under-inflated.
wear patterns will reduce tread life resulting in a need for
earlier tire replacement. Under-inflation, also increases CAUTION!
tire rolling resistance resulting in higher fuel After inspecting or adjusting the tire pressure, al-
consumption. ways reinstall the valve stem cap. This will prevent
Ride Comfort And Vehicle Stability moisture and dirt from entering the valve stem,
which could damage the valve stem.
Proper tire inflation contributes to a comfortable ride.
Over-inflation produces a jarring and uncomfortable
ride.
Inflation pressures specified on the placard are always inflation pressure should be increased by 3 psi (21 kPa),
cold tire inflation pressure. Cold tire inflation pressure which equals 1 psi (7 kPa) for every 12F (7C) for this
is defined as the tire pressure after the vehicle has not outside temperature condition.
been driven for at least three hours, or driven less than
Tire pressure may increase from 2 to 6 psi (13 to 40 kPa)
1 mile (1.6 km) after a three-hour period. The cold tire
during operation. Do not reduce this normal pressure
inflation pressure must not exceed the maximum infla-
buildup or your tire pressure will be too low.
tion pressure molded into the tire sidewall.
Tire Pressures For High-Speed Operation
Check tire pressures more often if subject to a wide range
The manufacturer advocates driving at safe speeds
of outdoor temperatures, as tire pressures vary with
temperature changes.
within posted speed limits. Where speed limits or condi- 5
tions are such that the vehicle can be driven at high
Tire pressures change by approximately 1 psi (7 kPa) per speeds, maintaining correct tire inflation pressure is very
12 F (7 C) of air temperature change. Keep this in mind important. Increased tire pressure and reduced vehicle
when checking tire pressure inside a garage, especially in loading may be required for high-speed vehicle opera-
the Winter. tion. Refer to original-equipment information, or an
authorized tire dealer, for recommended safe operating
Example: If garage temperature is 68F (20C) and the
speeds, loading and cold tire inflation pressures.
outside temperature is 32F (0C), then the cold tire
Cuts and punctures in radial tires are repairable only in
WARNING!
the tread area because of sidewall flexing. Consult your
High-speed driving, with your vehicle at or above authorized tire dealer for radial tire repairs.
maximum load, is dangerous. The added strain on
Spare Tire Matching Original Equipped Tire And
your tires could cause them to fail. You could have a
Wheel If Equipped
serious collision. Do not drive a vehicle loaded to the
Your vehicle may be equivalent with a spare tire and
maximum capacity at continuous speeds above
wheel in look and function as the original equipment tire
75 mph (120 km/h).
and wheel found on the front or rear axle of your vehicle.
This spare tire may be used in the tire rotation for your
Radial-Ply Tires
vehicle. If your vehicle has this option refer to an
authorized tire dealer for the recommended tire rotation
WARNING!
pattern.
Combining radial ply tires with other types of tires If your vehicle is not equipped with an original equip-
on your vehicle will cause your vehicle to handle ment tire and wheel as a spare, a non-matching tempo-
poorly. The instability could cause a collision. Al- rary emergency use spare may be equipped with your
ways use radial ply tires in sets of four. Never vehicle. Temporary use spares are engineered to be used
combine them with other types of tires. only with your vehicle. Your vehicle may be equipped
with one of the following types of non-matching tempo- Compact spare tire descriptions begin with the letter T
rary use spares; compact, full size, or limited-use. Do not or S preceding the size designation. Example: T145/
install more than one non-matching temporary use spare 80D18 103M.
tire/wheel on the vehicle at any given time.
T, S = Temporary Spare Tire
CAUTION! Since this tire has limited tread life the original equip-
ment tire should be repaired (or replaced) and reinstalled
Because of the reduced ground clearance, do not take
on your vehicle at the first opportunity.
your vehicle through an automatic car wash with a
compact, full size or limited-use temporary spare Do not install a wheel cover or attempt to mount a
installed. Damage to the vehicle may result. conventional tire on the compact spare wheel, since the 5
wheel is designed specifically for the compact spare tire.
Compact Spare Tire If Equipped Do not install more than one compact spare tire and
The compact spare is for temporary emergency use only. wheel on the vehicle at any given time
You can identify if your vehicle is equipped with a
compact spare by looking at the spare tire description on
the Tire and Loading Information Placard located on the
drivers side door opening or on the sidewall of the tire.
your original equipment tire, replace (or repair) the
WARNING!
original equipment tire and reinstall on the vehicle at the
Compact spares are for temporary emergency use first opportunity.
only. With these spares, do not drive more than
Limited-Use Spare If Equipped
50 mph (80 km/h). Temporary use spares have limited
The limited-use spare tire is for temporary emergency
tread life. When the tread is worn to the tread wear
use only. This tire is identified by a label located on the
indicators, the temporary use spare tire needs to be
limited-use spare wheel. This label contains the driving
replaced. Be sure to follow the warnings, which
limitations for this spare. This tire may look like the
apply to your spare. Failure to do so could result in
original equipped tire on the front or rear axle of your
spare tire failure and loss of vehicle control.
vehicle, but it is not. Installation of this limited-use spare
tire affects vehicle handling. Since it is not the same as
Full Size Spare If Equipped
your original equipment tire, replace (or repair) the
The full size spare is for temporary emergency use only.
original equipment tire and reinstall on the vehicle at the
This tire may look like the original equipped tire on the
first opportunity.
front or rear axle of your vehicle, but it is not. This spare
tire may have limited tread life. When the tread is worn
to the tread wear indicators, the temporary use full size
spare tire needs to be replaced. Since it is not the same as
Refer to Freeing A Stuck Vehicle in What To Do In
WARNING!
Emergencies for further information.
Limited-use spares are for emergency use only. In-
stallation of this limited-use spare tire affects vehicle WARNING!
handling. With this tire, do not drive more than the
Fast spinning tires can be dangerous. Forces gen-
speed listed on the limit-use spare wheel. Keep
erated by excessive wheel speeds may cause tire
inflated to the cold tire inflation pressure listed on
damage or failure. A tire could explode and injure
your Tire and Loading Information Placard located
someone.
on the drivers side door opening. Replace (or repair)
Do not spin your vehicles wheels faster than
the original equipment tire at the first opportunity
30 mph (48 km/h), or for more than 30 seconds
5
and reinstall it on your vehicle. Failure to do so could
continuously, when you are stuck; and do not let
result in loss of vehicle control.
anyone near a spinning wheel, no matter what the
Tire Spinning speed.
When stuck in mud, sand, snow, or ice conditions, do not
spin your vehicles wheels faster than 30 mph (48 km/h),
or for more than 30 seconds continuously, without stop-
ping.
Tread Wear Indicators These indicators are molded into the bottom of the tread
Tread wear indicators are in the original-equipment tires grooves. They will appear as bands when the tread depth
to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the
replaced. tread wear indicators, the tire should be replaced.
Life Of Tire
The service life of a tire is dependent upon varying
factors, including, but not limited to:
Driving style
Tire pressure
Distance driven
WARNING!
The tires and the spare tire should be replaced after
six years, regardless of the remaining tread. Failure to
1 Worn Tire follow this warning can result in sudden tire failure.
2 New Tire You could lose control and have a collision resulting
in serious injury or death.
Keep dismounted tires in a cool, dry place with as little It is recommended to replace the two front tires or two
exposure to light as possible. Protect tires from contact rear tires as a pair. Replacing just one tire can seriously
with oil, grease and gasoline. affect your vehicles handling. If you ever replace a
wheel, make sure that the wheels specifications match
Replacement Tires
those of the original wheels.
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for It is recommended you contact your original equipment
wear and correct cold tire inflation pressure. The manu- or an authorized tire dealer with any questions you may
facturer strongly recommends that you use tires equiva- have on tire specifications or capability. Failure to use
lent to the originals in size, quality and performance equivalent replacement tires may adversely affect the
when replacement is needed. Please see Tread Wear safety, handling, and ride of your vehicle. 5
Indicators and Tire and Loading Information placard
for the size designation of your tire. The Load Index and
Speed Symbol for your tire will be found on the original
equipment tire sidewall. See the Tire Sizing Chart ex-
ample found in the Tire Safety Information section of this
manual for more information relating to the Load Index
and Speed Symbol of a tire.

Do not use a tire, wheel size or rating other than Failure to equip your vehicle with tires having
that specified for your vehicle. Some combinations adequate speed capability can result in sudden tire
of unapproved tires and wheels may change sus- failure and loss of vehicle control.
pension dimensions and performance characteris-
tics, resulting in changes to steering, handling, and CAUTION!
braking of your vehicle. This can cause unpredict-
able handling and stress to steering and suspen- Replacing original tires with tires of a different size
sion components. You could lose control and have may result in false speedometer and odometer read-
a collision resulting in serious injury or death. Use ings.
only the tire and wheel sizes with load ratings
approved for your vehicle. TIRE CHAINS
Never use a tire with a smaller load index or Use only compact chains, or other traction aids that meet
capacity, than what was originally equipped on SAE type Class S specifications. Chains must be the
your vehicle. Using a tire with a smaller load index proper size for the vehicle, as recommended by the chain
could result in tire overloading and failure. You manufacturer.
could lose control and have a collision. NOTE: Do not use tire chains on a compact spare tire.
(Continued)
CAUTION! CAUTION! (Continued)

To avoid damage to your vehicle or tires, observe the Install chains on the front wheels as tightly as
following precautions: possible and then retighten after driving about
Use chains on P225/65R16 and P235/60R16 tires 0.5 mile (0.8 km).
only. P225/65R17 tires do not provide adequate Do not drive for prolonged periods of time on dry
clearance. pavement.
Because of restricted chain clearance between tires Observe the tire chain manufacturers instructions
and other suspension components, it is important on the method of installation, operating speed,
that only chains in good condition are used. Bro- and conditions for use. Always use the lower 5
ken chains can cause serious damage. Stop the suggested operating speed of the chain manufac-
vehicle immediately if noise occurs that could turer, if different from the speed recommended by
indicate chain breakage. Remove the damaged the vehicle manufacturer.
parts of the chain before further use.
Always use the lower suggested operating speed if the
Do not exceed 45 mph (70 km/h).
chain manufacturer and vehicle manufacturer suggest
Drive cautiously and avoid severe turns and large
different maximum speeds. This notice applies to all
bumps, especially with a loaded vehicle.
chain traction devices, including link and cable (radial)
(Continued) chains.
SNOW TIRES poorer than that of non-studded tires. Some states pro-
Some areas of the country require the use of snow tires hibit studded tires; therefore, local laws should be
during the winter. All season tires can be identified by the checked before using these tire types.
M+S designation on the tire sidewall.
TIRE ROTATION RECOMMENDATIONS
If you need snow tires, select tires equivalent in size and The tires on the front and rear of your vehicle operate at
type to the original equipment tires. Use snow tires only different loads and perform different steering, driving,
in sets of four; failure to do so may adversely affect the and braking functions. For these reasons, they wear at
safety and handling of your vehicle. unequal rates.
Snow tires generally have lower speed ratings than what These effects can be reduced by timely rotation of tires.
was originally equipped with your vehicle and should The benefits of rotation are especially worthwhile with
not be operated at sustained speeds over 75 mph aggressive tread designs such as those on all season type
(120 km/h). For speeds above 75 mph (120 km/h) refer to tires. Rotation will increase tread life, help to maintain
original equipment or an authorized tire dealer for mud, snow and wet traction levels, and contribute to a
recommended safe operating speeds, loading and cold smooth, quiet ride.
tire inflation pressures.
Refer to the Maintenance Schedule for the proper
While studded tires improve performance on ice, skid maintenance intervals. The reasons for any rapid or
and traction capability on wet or dry surfaces may be unusual wear should be corrected prior to rotation being
performed.
The suggested rotation method is the rearward cross TIRE PRESSURE MONITOR SYSTEM (TPMS)
shown in the following diagram. This rotation pattern The TPMS will warn the driver of a low tire pressure
does not apply to some directional tires that must not be based on the cold inflation tire placard pressure require-
reversed. ments found on the tire placard label located on the
drivers-side B-pillar.
The tire pressure will vary with temperature by about
1 psi (6.9 kPa) for every 12F (6.5C). This means that
when the outside temperature decreases, the tire pressure
will decrease. Tire pressure should always be set based
on cold inflation tire pressure. This is defined as the tire 5
pressure after a vehicle has not been driven for more than
three hours - and in outside ambient temperature. Refer
to Tires General Information in Starting and
Operating for information on how to properly inflate
the vehicles tires. The tire pressure will also increase as
the vehicle is driven - this is normal and there should be
Tire Rotation
no adjustment for this increased pressure.
The TPMS will warn the driver of a low tire pressure if For example, your vehicle may have a recommended
the tire pressure falls below the low pressure warning cold (parked for more than three hours) tire placard
threshold for any reason, including low temperature pressure of 35 psi (241 kPa). If the ambient temperature is
effects, or natural air pressure loss through the tire. 68F (20C) and the measured tire pressure is 30 psi
(207 kPa), a temperature drop to 20F (-7C) will decrease
The TPMS will continue to warn the driver of low tire
the tire pressure to approximately 26 psi (179 kPa). This
pressure as long as the condition exists, and will not turn
tire pressure is sufficiently low enough to turn on the
off until the tire pressure is at or above recommended
Tire Pressure Monitoring Telltale Light. Driving the
cold tire placard pressure. Once the low tire pressure
vehicle may cause the tire pressure to rise to approxi-
warning has been illuminated, the tire pressure must be
mately 30 psi (207 kPa), but the Tire Pressure Monitor-
increased to the recommended cold tire placard pressure
ing Telltale Light will still be on. In this situation, the
in order for the Tire Pressure Monitoring Telltale Light
Tire Pressure Monitoring Telltale Light will turn off
to be turned off. The system will automatically update
only after the tires have been inflated to the vehicles
and the Tire Pressure Monitoring Telltale Light will
recommended cold tire placard pressure value.
extinguish once the updated tire pressures have been
received.
NOTE: The vehicle may need to be driven for up to
20 minutes above 15 mph (24 km/h) to receive this
information.
NOTE:
CAUTION!
The TPMS is not intended to replace normal tire care
The TPMS has been optimized for the original and maintenance, or to provide warning of a tire
equipment tires and wheels. TPMS pressures have failure or condition.
been established for the tire size equipped on your
The TPMS should not be used as a tire pressure gauge
vehicle. Undesirable system operation or sensor
while adjusting your tire pressure.
damage may result when using replacement
equipment that is not of the same size, type, and/or Driving on a significantly under-inflated tire causes
style. Aftermarket wheels can cause sensor dam- the tire to overheat and can lead to tire failure.
age. Do not use aftermarket sealants or balance Under-inflation also reduces fuel efficiency and tire 5
beads if your vehicle is equipped with a TPMS, as tread life, and may affect the vehicles handling and
damage to the sensors may result. stopping ability.
After inspecting or adjusting the tire pressure The TPMS is not a substitute for proper tire mainte-
always reinstall the valve stem cap. This will nance, and it is the drivers responsibility to maintain
prevent moisture and dirt from entering the valve correct tire pressure, using an accurate tire pressure
stem, which could damage the TPMS sensor. gage, even if under-inflation has not reached the level
to trigger illumination of the Tire Pressure Monitor-
ing Telltale Light.
Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Tire Pressure
and the TPMS will monitor the actual tire pressure in Warnings
the tire. The Tire Pressure Monitoring Telltale Light
will illuminate in the instrument cluster, a
Base System
LOW TIRE PRESSURE message will display
The TPMS uses wireless technology with wheel rim
in the instrument cluster, and an audible chime
mounted electronic sensors to monitor tire pressure lev-
will be activated when one or more of the four active
els. Sensors, mounted to each wheel as part of the valve
road tire pressures are low. Should this occur, you should
stem, transmit tire pressure readings to the Receiver
stop as soon as possible, check the inflation pressure of
Module.
each tire on your vehicle, and inflate each tire to the
NOTE: It is particularly important for you to check the vehicles recommended cold tire placard pressure value
tire pressure in all of your tires regularly and to maintain (located on the placard label on the drivers-side B-Pillar).
the proper pressure. The system will automatically update and the Tire
Pressure Monitoring Telltale Light will extinguish once
The Basic TPMS consists of the following components:
the updated tire pressures have been received.
Receiver Module
NOTE: The vehicle may need to be driven for up to
Four Tire Pressure Monitoring Sensors 20 minutes above 15 mph (24 km/h) to receive this
information.
TPMS Telltale Warning Light
The Tire Pressure Monitoring Telltale Light will flash Vehicles With Compact Spare
on and off for 75 seconds, and remain on solid when a
1. The compact spare tire (if equipped) does not have a
system fault is detected. The system fault will also sound
TPMS sensor. Therefore the TPMS will not monitor the
a chime. If the ignition switch is cycled, this sequence will
pressure in the compact spare tire.
repeat, providing the system fault still exists. The Tire
Pressure Monitoring Telltale Light will turn off when 2. If you install the compact spare tire in place of a road
the fault condition no longer exists. A system fault can tire that has a pressure below the low-pressure warning
occur with any of the following scenarios: limit, upon the next ignition switch cycle, a chime will
sound, a LOW TIRE PRESSURE message will be
1. Jamming due to electronic devices or driving next to
facilities emitting the same radio frequencies as the TPMS
displayed and the Tire Pressure Monitoring Telltale 5
Light will turn on.
sensors.
3. After driving for up to 20 minutes above 15 mph
2. Installing some form of aftermarket window tinting
(24 km/h), the Tire Pressure Monitoring Telltale Light
that affects radio wave signals.
will flash on and off for 75 seconds and then remain on
3. Accumulation of excessive snow and/or ice around solid.
the wheels or wheel housings.
4. For each subsequent ignition switch cycle, a chime will
4. Using tire chains on the vehicle. sound, the Tire Pressure Monitoring Telltale Light will
flash on and off for 75 seconds and then remain on solid.
5. Using wheels/tires not equipped with TPMS sensors.
5. Once you repair or replace the original road tire and NOTE: It is particularly important to regularly check
reinstall it on the vehicle in place of the compact spare and maintain proper tire pressure in all the tires.
tire, the TPMS will automatically update, and the Tire
The Premium TPMS consists of the following compo-
Pressure Monitoring Telltale Light will turn off as long
nents:
as no tire pressure is below the low-pressure warning
limit in any of the four active road tires. Receiver Module
NOTE: The vehicle may need to be driven for up to Four TPMS Sensors
20 minutes above 15 mph (24 km/h) for the TPMS to
Various TPMS messages, which display in the Elec-
receive this information.
tronic Vehicle Information Center (EVIC), and graph-
Premium System If Equipped ics displaying tire pressures
The TPMS uses wireless technology with wheel rim-
TPMS Telltale Warning Light
mounted electronic sensors to monitor tire pressure lev-
els. Sensors mounted to each wheel as part of the valve TPMS Low Pressure Warnings
stem transmit tire pressure readings to the Receiver The Tire Pressure Monitoring Telltale Light will illumi-
Module. nate in the instrument cluster, and an audible chime will
be activated when one or more of the four active road tire
pressures are low. In addition, the EVIC will display a
LOW TIRE PRESSURE message for a minimum of five Should a low tire condition occur on any of the four
seconds and a graphic display of the pressure value(s) active road tire(s), you should stop as soon as possible,
with the low tire(s) flashing. and inflate the low tire(s) that is flashing on the graphic
display to the vehicles recommended cold tire pressure
value. The system will automatically update, the graphic
display of the pressure value(s) will stop flashing, and
the Tire Pressure Monitoring Telltale Light will extin-
guish once the updated tire pressure(s) have been re-
ceived.
NOTE: The vehicle may need to be driven for up to 5
20 minutes above 15 mph (24 km/h) to receive this
information.
SERVICE TPM SYSTEM Message
The Tire Pressure Monitoring Telltale Light will flash
Low Tire Pressure Display on and off for 75 seconds, and remain on solid when a
system fault is detected. The system fault will also sound
a chime. The EVIC will display a SERVICE TPM SYS-
TEM message for a minimum of five seconds. This text
message is then followed by a graphic display, with - - in Light will no longer flash, the SERVICE TPM SYSTEM
place of the pressure value(s) indicating which TPMS message will not be present, and a pressure value will be
Sensor(s) is not being received. displayed instead of dashes. A system fault can occur by
any of the following scenarios:
1. Jamming due to electronic devices or driving next to
facilities emitting the same radio frequencies as the TPMS
sensors.
2. Installing some form of aftermarket window tinting
that affects radio wave signals.
3. Accumulation of excessive snow and/or ice around
the wheels or wheel housings.
4. Using tire chains on the vehicle.
5. Using wheels/tires not equipped with TPMS sensors.
SERVICE TPM SYSTEM Display
If the ignition switch is cycled, this sequence will repeat, The EVIC will also display a SERVICE TPM SYSTEM
providing the system fault still exists. If the system fault message for a minimum of five seconds when a system
no longer exists, the Tire Pressure Monitoring Telltale fault possibly related to an incorrect sensor location fault
is present. In this case, the SERVICE TPM SYSTEM 3. After driving the vehicle for up to 20 minutes above
message is then followed by a graphic display with 15 mph (24 km/h), the Tire Pressure Monitoring Telltale
pressure values still shown. This indicates that the pres- Light will flash on and off for 75 seconds and then
sure values are still being received from the TPM sensors remain on solid. In addition, the EVIC will display a
but they may not be in the correct vehicle position. The SERVICE TPM SYSTEM message for a minimum of
system still needs to be serviced as long as the SERVICE five seconds and then display dashes (- -) in place of the
TPM SYSTEM message exists. pressure value.
Vehicles With Compact Spare 4. For each subsequent ignition switch cycle, a chime will
sound, the Tire Pressure Monitoring Telltale Light will
1. The compact spare tire (if equipped) does not have a
flash on and off for 75 seconds and then remain on solid, 5
TPMS. Therefore, the TPMS will not monitor the pressure
and the EVIC will display a SERVICE TPM SYSTEM
in the compact spare tire.
message for a minimum of five seconds and then display
2. If you install the compact spare tire in place of a road dashes (- -) in place of the pressure value.
tire that has a pressure below the low-pressure warning
5. Once you repair or replace the original road tire, and
limit, upon the next ignition switch cycle, the Tire
reinstall it on the vehicle in place of the compact spare,
Pressure Monitoring Telltale Light will remain on, the
the TPMS will update automatically. In addition, the
LOW TIRE PRESSURE message will be displayed, a
Tire Pressure Monitoring Telltale Light will turn off
chime will sound, and the EVIC will still display a
and the graphic in the EVIC will display a new pressure
flashing pressure value in the graphic display.
value instead of dashes (- -), as long no tire pressure is The tire pressure sensors are regulated under one of the
below the low pressure warning limit in any of the four following licenses:
active road tires.
NOTE: The vehicle may need to be driven for up to United States . . . . . . . . . . . . . . . . . . . MRXC4W4MA4
20 minutes above 15 mph (24 km/h) in order for the Canada . . . . . . . . . . . . . . . . . . . . . 2546A-C4W4MA4
TPMS to receive this information. FUEL REQUIREMENTS
General Information 3.6L Engine
This device complies with Part 15 of the FCC rules and This engine is designed to meet all emis-
RSS 210 of Industry Canada. Operation is subject to the sions regulations and provide excellent
following conditions: fuel economy and performance when us-
This device may not cause harmful interference. ing high-quality unleaded regular gaso-
line having an octane rating of 87. The use
This device must accept any interference received, of premium gasoline is not recommended,
including interference that may cause undesired as it will not provide any benefit over regular gasoline in
operation. these engines.
Light spark knock at low engine speeds is not harmful to Reformulated Gasoline
your engine. However, continued heavy spark knock at Many areas of the country require the use of cleaner
high speeds can cause damage and immediate service is burning gasoline referred to as Reformulated Gasoline.
required. Poor quality gasoline can cause problems such Reformulated gasoline contains oxygenates and are spe-
as hard starting, stalling, and hesitations. If you experi- cifically blended to reduce vehicle emissions and im-
ence these symptoms, try another brand of gasoline prove air quality.
before considering service for the vehicle.
The manufacturer supports the use of reformulated gaso-
Over 40 auto manufacturers worldwide have issued and line. Properly blended reformulated gasoline will pro-
endorsed consistent gasoline specifications (the World- vide excellent performance and durability of engine and
wide Fuel Charter, WWFC) which define fuel properties fuel system components. 5
necessary to deliver enhanced emissions, performance,
Gasoline/Oxygenate Blends
and durability for your vehicle. The manufacturer recom-
Some fuel suppliers blend unleaded gasoline with oxy-
mends the use of gasolines that meet the WWFC speci-
genates such as Ethanol. Fuels blended with oxygenates
fications if they are available.
may be used in your vehicle.
If a Non-FFV vehicle is inadvertently fueled with E-85
CAUTION!
fuel, the engine will have some or all of these symptoms:
DO NOT use gasoline containing Methanol or gaso-
operate in a lean mode
line containing more than 10% Ethanol. Use of these
blends may result in starting and driveability prob- OBD II Malfunction Indicator Light on
lems, damage critical fuel system components, cause
poor engine performance
emissions to exceed the applicable standard, and/or
cause the Malfunction Indicator Light to illumi- poor cold start and cold driveability
nate. Pump labels should clearly communicate if a
increased risk for fuel system component corrosion
fuel contains greater than 10% Ethanol.
To fix a Non-FFV vehicle inadvertently fueled once with
Problems that result from using gasoline containing E-85 perform the following:
Methanol or gasoline containing more than 10% Ethanol
change the engine oil and oil filter
are not the responsibility of the manufacturer and may
not be covered under warranty. disconnect and reconnect the battery
E-85 Usage In Non-Flex Fuel Vehicles drain the fuel tank (see your authorized dealer)
Non-FFV vehicles are compatible with gasoline contain-
More extensive repairs will be required for prolonged
ing 10% ethanol (E10). Gasoline with higher ethanol
exposure to E-85 fuel.
content may void the vehicles warranty.
MMT In Gasoline Materials Added To Fuel
MMT is a manganese-containing metallic additive that is All gasoline sold in the United States is required to
blended into some gasoline to increase octane. Gasoline contain effective detergent additives. Use of additional
blended with MMT provides no performance advantage detergents or other additives is not needed under normal
beyond gasoline of the same octane number without conditions and they would result in additional cost.
MMT. Gasoline blended with MMT reduces spark plug Therefore, you should not have to add anything to the
life and reduces emissions system performance in some fuel.
vehicles. The manufacturer recommends that gasoline
Fuel System Cautions
without MMT be used in your vehicle. The MMT content
of gasoline may not be indicated on the gasoline pump,
CAUTION! 5
therefore, you should ask your gasoline retailer whether
the gasoline contains MMT. It is even more important to Follow these guidelines to maintain your vehicles
look for gasoline without MMT in Canada, because MMT performance:
can be used at levels higher than those allowed in the The use of leaded gas is prohibited by Federal law.
United States. MMT is prohibited in Federal and Califor- Using leaded gasoline can impair engine perfor-
nia reformulated gasoline. mance and damage the emissions control system.
(Continued)
Carbon Monoxide Warnings
An out-of-tune engine or certain fuel or ignition WARNING!
malfunctions can cause the catalytic converter to
overheat. If you notice a pungent burning odor or Carbon monoxide (CO) in exhaust gases is deadly.
some light smoke, your engine may be out of tune Follow the precautions below to prevent carbon
or malfunctioning and may require immediate monoxide poisoning:
service. Contact your authorized dealer for service Do not inhale exhaust gases. They contain carbon
assistance. monoxide, a colorless and odorless gas, which can
The use of fuel additives, which are now being kill. Never run the engine in a closed area, such as
sold as octane enhancers, is not recommended. a garage, and never sit in a parked vehicle with the
Most of these products contain high concentra- engine running for an extended period. If the
tions of methanol. Fuel system damage or vehicle vehicle is stopped in an open area with the engine
performance problems resulting from the use of running for more than a short period, adjust the
such fuels or additives is not the responsibility of ventilation system to force fresh, outside air into
the manufacturer. the vehicle.
(Continued)
NOTE: Intentional tampering with the emissions con-
trol system can result in civil penalties being assessed
against you.
the other sections of this manual for information on
features that are common between Flexible Fuel and
Guard against carbon monoxide with proper gasoline-only powered vehicles.
maintenance. Have the exhaust system inspected
every time the vehicle is raised. Have any abnor-
mal conditions repaired promptly. Until repaired,
drive with all side windows fully open.
Keep the liftgate closed when driving your vehicle
to prevent carbon monoxide and other poisonous
exhaust gases from entering the vehicle. 5
FLEXIBLE FUEL IF EQUIPPED
E-85 General Information
The information in this section is for Flexible Fuel ve-
hicles only. These vehicles can be identified by a unique
E-85 Fuel Cap
fuel filler door label that states Ethanol (E-85) or Un-
leaded Gasoline Only. This section only covers those
subjects that are unique to these vehicles. Please refer to
Ethanol Fuel (E-85)
CAUTION!
E-85 is a mixture of approximately 85% fuel ethanol and
Only vehicles with the E-85 fuel filler door label can 15% unleaded gasoline.
operate on E-85.
WARNING!
Ethanol vapors are extremely flammable and could
cause serious personal injury. Never have any smok-
ing materials lit in or near the vehicle when remov-
ing the fuel filler tube cap (gas cap) or filling the
tank. Do not use E-85 as a cleaning agent and never
use it near an open flame.
Fuel Requirements
Your vehicle will operate on both unleaded gasoline with
an octane rating of 87, or E-85 fuel, or any mixture of
these two. For best results, a refueling pattern that
E-85 Badge alternates between E-85 and unleaded gasoline should be
avoided.
When you do switch fuel types it is recommended that: Some additives used in regular gasoline are not fully
compatible with E-85 and may form deposits in your
you do not switch when the fuel gauge indicates less
engine. To eliminate driveability issues that may be
than 1/4 full
caused by these deposits, a supplemental gasoline
you do not add less than 5 gallons (19 Liters) when additive, such as MOPAR Injector Cleanup or
refueling Techron may be used.
you operate the vehicle immediately after refueling for Selection Of Engine Oil For Flexible Fuel Vehicles
a period of at least 5 minutes (E-85) And Gasoline Vehicles
FFV vehicles operated on E-85 require specially formu-
Observing these precautions will avoid possible hard
lated engine oils. These special requirements are included 5
starting and/or significant deterioration in driveability
in MOPAR engine oils, and in equivalent oils meeting
during warm up.
Chrysler Specification MS-6395. The manufacturer re-
NOTE: quires engine oils that are API Certified and meet the
When the ambient temperature is above 90 F (32 C), requirements of Material Standard MS-6395. MS-6395
you may experience hard starting and rough idle contains additional requirements, developed during ex-
following start up even if the above recommendations tensive fleet testing, to provide additional protection to
are followed. Chrysler Group LLC engines. Use MOPAR or an
equivalent oil meeting the specification MS-6395.
Starting Replacement Parts
The characteristics of E-85 fuel make it unsuitable for use Many components in your Flexible Fuel Vehicle (FFV) are
when ambient temperatures fall below 0F (-18C). In the designed to be compatible with ethanol. Always be sure
range of 0F (-18C) to 32F (0C), you may experience an that your vehicle is serviced with correct ethanol com-
increase in the time it takes for your engine to start, and patible parts.
a deterioration in driveability (sags and/or hesitations)
until the engine is fully warmed up. CAUTION!
NOTE: Use of the engine block heater (if equipped) is Replacing fuel system components with non-ethanol
beneficial for E-85 startability when the ambient tempera- compatible components can damage your vehicle.
ture is less than 32F (0C).
Maintenance
Cruising Range
Because E-85 fuel contains less energy per gallon/liter
CAUTION!
than gasoline, you will experience an increase in fuel
consumption. You can expect your miles per gallon Do not use ethanol mixture greater than 85% in your
(mpg)/miles per liter and your driving range to decrease vehicle. It will cause difficulty in cold starting and
by about 30%, compared to gasoline operation. may affect driveability.
ADDING FUEL NOTE: The drivers side sliding door cannot be opened
while the fuel door is open. This feature operates only
Fuel Filler Cap (Gas Cap)
when the sliding door is fully closed prior to opening the
The gas cap is located behind the fuel filler door on the
fuel door.
left side of the vehicle. If the gas cap is lost or damaged,
be sure the replacement cap is for use with this vehicle.
CAUTION!
Damage to the fuel system or emissions control
system could result from using an improper fuel
tank filler tube cap (gas cap). A poorly fitting cap
could let impurities into the fuel system and may
5
cause the Malfunction Indicator Light (MIL) to
turn on, due to fuel vapors escaping from the
system.
To avoid fuel spillage and overfilling, do not top
off the fuel tank after filling.
Fuel Filler Cap

If the gas cap is not tightened properly, the MIL may
WARNING!
come on. Be sure the gas cap is tightened every time
Never have any smoking materials lit in or near the vehicle is refueled.
the vehicle when the gas cap is removed or the
Loose Fuel Filler Cap Message
tank is being filled.
If the vehicle diagnostic system determines that the fuel
Never add fuel when the engine is running. This is filler cap is loose, improperly installed, or damaged, a
in violation of most state and federal fire regula- gASCAP message will display in the odometer or a
tions and may cause the MIL to turn on. CHECK GASCAP message will be displayed in the
A fire may result if gasoline is pumped into a Electronic Vehicle Information Center (EVIC). Refer to
portable container that is inside of a vehicle. You Electronic Vehicle Information Center in Understand-
could be burned. Always place gas containers on ing Your Instrument Panel for further information.
the ground while filling. Tighten the fuel filler cap until a clicking sound is heard.
This is an indication that the fuel filler cap is properly
NOTE: tightened. Refer to Onboard Diagnostic System in
When the fuel nozzle clicks or shuts off, the fuel Maintaining Your Vehicle for further information.
tank is full.
If the problem continues, the message will appear the
Tighten the fuel filler cap until you hear a clicking next time the vehicle is started. See your authorized
sound. This is an indication that the fuel filler cap is dealer as soon as possible.
properly tightened.
VEHICLE LOADING Vehicle Identification Number (VIN)
As required by National Highway Traffic Safety Admin-
Type of Vehicle
istration regulations, your vehicle has a certification label
affixed to the drivers side door or B-Pillar. Month, Day and Hour of Manufacture (MDH)
If seats are removed for carrying cargo, do not exceed the The bar code allows a computer scanner to read the
specified GVWR and GAWR. Vehicle Identification Number (VIN).
Vehicle Certification Label Gross Vehicle Weight Rating (GVWR)
Your vehicle has a Vehicle Certification Label attached to The GVWR is the total allowable weight of your vehicle.
the drivers door B-Pillar. This includes driver, passengers, and cargo. The total 5
load must be limited so that you do not exceed the
The label contains the following information:
GVWR.
Name of manufacturer
Gross Axle Weight Rating (GAWR)
Month and year of manufacture The GAWR is the maximum capacity of the front and rear
axles. Distribute the load over the front and rear axles
Gross Vehicle Weight Rating (GVWR)
evenly. Make sure that you do not exceed either front or
Gross Axle Weight Rating (GAWR) Front rear GAWR.
Gross Axle Weight Rating (GAWR) Rear
Curb Weight
WARNING!
The curb weight of a vehicle is defined as the total weight
Because the front wheels drive and steer the vehicle, of the vehicle with all fluids, including vehicle fuel, at full
it is important that you do not exceed the maximum capacity conditions, and with no occupants or cargo
front or rear GAWR. A dangerous driving condition loaded into the vehicle. The front and rear curb weight
can result if either rating is exceeded. You could lose values are determined by weighing your vehicle on a
control of the vehicle and have a collision. commercial scale before any occupants or cargo are
added.
Tire Size
Overloading
The tire size on the Vehicle Certification Label represents
The load carrying components (axle, springs, tires,
the actual tire size on your vehicle. Replacement tires
wheels, etc.) of your vehicle will provide satisfactory
must be equal to the load capacity of this tire size.
service as long as you do not exceed the GVWR and front
Rim Size and rear GAWR.
This is the rim size that is appropriate for the tire size
The best way to figure out the total weight of your
listed.
vehicle is to weigh it when it is fully loaded and ready for
Inflation Pressure operation. Weigh it on a commercial scale to ensure that
This is the cold tire inflation pressure for your vehicle, for it is not over the GVWR.
all loading conditions up to full GAWR.
Figure out the weight on the front and rear of the vehicle
CAUTION!
separately. It is important that you distribute the load
evenly over the front and rear axles. Do not load your vehicle any heavier than the GVWR
or the maximum front and rear GAWR. If you do,
Overloading can cause potential safety hazards and
parts on your vehicle can break, or it can change the
shorten useful service life. Heavier axles or suspension
way your vehicle handles. This could cause you to
components do not necessarily increase the vehicles
lose control. Also, overloading can shorten the life of
GVWR.
your vehicle.
Loading
To load your vehicle properly, first figure out its empty TRAILER TOWING 5
weight, axle-by-axle and side-by-side. Store heavier items In this section you will find safety tips and information
down low and be sure you distribute their weight as on limits to the type of towing you can reasonably do
evenly as possible. Stow all loose items securely before with your vehicle. Before towing a trailer, carefully
driving. If weighing the loaded vehicle shows that you review this information to tow your load as efficiently
have exceeded either GAWR, but the total load is within and safely as possible.
the specified GVWR, you must redistribute the weight.
Improper weight distribution can have an adverse effect To maintain warranty coverage, follow the requirements
on the way your vehicle steers and handles, and the way and recommendations in this manual concerning ve-
the brakes operate. hicles used for trailer towing.
Common Towing Definitions Gross Combination Weight Rating (GCWR)
The following trailer towing-related definitions will as- The GCWR is the total permissible weight of your vehicle
sist you in understanding the following information: and trailer when weighed in combination.
Gross Vehicle Weight Rating (GVWR) NOTE: The GCWR rating includes a 150 lbs (68 kg)
The GVWR is the total allowable weight of your vehicle. allowance for the presence of a driver.
This includes driver, passengers, cargo/luggage and
Gross Axle Weight Rating (GAWR)
trailer tongue weight. The total load must be limited so
The GAWR is the maximum capacity of the front and rear
that you do not exceed the GVWR. Refer to Vehicle
axles. Distribute the load over the front and rear axles
Loading/Vehicle Certification Label in Starting and
evenly. Make sure that you do not exceed either front or
Operating for further information.
rear GAWR. Refer to Vehicle Loading/Vehicle Certifica-
Gross Trailer Weight (GTW) tion Label in Starting and Operating for further
The GTW is the weight of the trailer plus the weight of all information.
cargo, consumables and equipment (permanent or tem-
porary) loaded in or on the trailer in its loaded and
ready for operation condition.
The recommended way to measure GTW is to put your
fully loaded trailer on a vehicle scale. The entire weight
of the trailer must be supported by the scale.
Trailer Sway Control
WARNING!
The trailer sway control is a telescoping link that can be
It is important that you do not exceed the maximum installed between the hitch receiver and the trailer tongue
front or rear GAWR. A dangerous driving condition that typically provides adjustable friction associated with
can result if either rating is exceeded. You could lose the telescoping motion to dampen any unwanted trailer
control of the vehicle and have a collision. swaying motions while traveling.
Weight-Carrying Hitch
Trailer Tongue Weight (TW)
A weight-carrying hitch supports the trailer tongue
The TW is the downward force exerted on the hitch ball
weight, just as if it were luggage located at a hitch ball or
by the trailer. In most cases it should not be less than 10%
some other connecting point of the vehicle. This type of 5
or more than 15% of the trailer load. You must consider
hitch is the most popular on the market today and they
this as part of the load on your vehicle.
are commonly used to tow small- and medium-sized
Frontal Area trailers.
The frontal area is the maximum height multiplied by the
maximum width of the front of a trailer.
Weight-Distributing Hitch
WARNING!
A weight-distributing system works by applying lever-
age through spring (load) bars. They are typically used An improperly adjusted weight-distributing hitch
for heavier loads to distribute trailer tongue weight to the system may reduce handling, stability, braking
tow vehicles front axle and the trailers axle(s). When performance, and could result in a collision.
used in accordance with the manufacturers directions, it Weight-distributing hitch systems may not be
provides for a more level ride, offering more consistent compatible with surge brake couplers. Consult
steering and brake control thereby enhancing towing with an authorized hitch and trailer manufacturer
safety. The addition of a friction/hydraulic sway control or a reputable authorized Recreational Vehicle
also dampens sway caused by traffic and crosswinds and dealer for additional information.
contributes positively to tow vehicle and trailer stability.
Trailer sway control and a weight distributing (load
equalizing) hitch are recommended for heavier tongue
weights (TW), and may be required depending on vehicle
and trailer configuration/loading to comply with gross
axle weight rating (GAWR) requirements.
Without Weight-Distributing Hitch (Incorrect) With Weight-Distributing Hitch (Correct)

Trailer Hitch Classification
The following chart provides the industry standard for
the maximum trailer weight a given trailer hitch class can
tow, and should be used to assist you in selecting the
correct trailer hitch for your intended towing condition.
TRAILER HITCH CLASSIFICATIONS
Max. GTW
Class
(Gross Trailer Wt.)
Class I - Light Duty 2,000 lbs (907 kg)
Class II - Medium Duty 3,500 lbs (1 587 kg)
Class III - Heavy Duty 5,000 lbs (2 268 kg)
Improper Adjustment of Weight-Distributing Class IV - Extra Heavy 10,000 lbs (4 540 kg)
Hitch (Incorrect) Duty
Refer to the Trailer Towing Weights (Maximum
Trailer Weight Ratings) chart for the Maximum
Gross Trailer Weight (GTW) towable for your given
drivetrain.
Trailer Towing Weights (Maximum Trailer Weight Ratings)
The following chart provides the maximum trailer weight ratings towable for your given drivetrain.
GCWR (Gross Com- Max. GTW
Engine/Transmission Frontal Area Max. Tongue Wt.
bined Wt. Rating) (Gross Trailer Wt.)
Up to 2 persons &
8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,600 lbs 360 lbs (163 kg)
(1 633 kg)*
3 to 5 persons &
3.6L/Automatic 8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,350 lbs 335 lbs (152 kg)
(1 519 kg)* 5
6 to 7 persons &
8,750 lbs (3 969 kg) 40 sq ft (3.72 sq m) Luggage 3,000 lbs 300 lbs (136 kg)
(1 360 kg)*
* For vehicles equipped with Fold-in-Floor seating, the Gross Trailer Weight must be reduced by 100 lbs (45 kg).
Refer to local laws for maximum trailer towing speeds.
NOTE: The trailer tongue weight must be considered as part of the combined weight of occupants and
cargo, and should never exceed the weight referenced on the Tire and Loading Information placard. Refer to
Tire Safety Information in Starting and Operating for further information.
Trailer And Tongue Weight
Always load a trailer with 60% to 65% of the weight in
the front of the trailer. This places 10% to 15% of the
Gross Trailer Weight (GTW) on the tow hitch of your
vehicle. Loads balanced over the wheels or heavier in the
rear can cause the trailer to sway severely side-to-side,
which will cause loss of control of the vehicle and trailer.
Failure to load trailers heavier in front is the cause of
many trailer collisions.
Never exceed the maximum trailer tongue weight
stamped on your bumper or trailer hitch.
Consider the following items when computing the
weight on the rear axle of the vehicle:
The tongue weight of the trailer.
The weight of any other type of cargo/luggage or
equipment put in or on your vehicle.
The weight of the driver and all passengers.
NOTE: Remember that everything put into or on the
trailer adds to the load on your vehicle. Also, additional
factory-installed options, or authorized dealer-installed Then, during the first 500 miles (805 km) that a
options, must be considered as part of the total load on trailer is towed, do not drive over 50 mph
your vehicle. Refer to the Tire Safety Information/Tire (80 km/h) and do not make starts at full throttle.
and Loading Information Placard in Starting and Op- This helps the engine and other parts of the
erating for the maximum combined weight of occupants vehicle wear in at the heavier loads.
and cargo for your vehicle.
Perform the maintenance listed in the Maintenance
Towing Requirements Schedule. Refer to Maintenance Schedule for further
To promote proper break-in of your new vehicle drive- information. When towing a trailer, never exceed the 5
train components, the following guidelines are recom- GAWR or GCWR ratings.
mended:
WARNING!
CAUTION!
Improper towing can lead to a injury collision. Fol-
Do not tow a trailer at all during the first 500 miles low these guidelines to make your trailer towing as
(805 km) the new vehicle is driven. The engine, safe as possible:
axle or other parts could be damaged.
(Continued)
(Continued)

Make certain that the load is secured in the trailer Vehicles with trailers should not be parked on a
and will not shift during travel. When trailering grade. When parking, apply the parking brake on
cargo that is not fully secured, dynamic load shifts the tow vehicle. Put the tow vehicle automatic
can occur that may be difficult for the driver to transmission in PARK. Always, block or chock
control. You could lose control of your vehicle and the trailer wheels.
have a collision. GCWR must not be exceeded.
When hauling cargo or towing a trailer, do not Total weight must be distributed between the tow
overload your vehicle or trailer. Overloading can vehicle and the trailer such that the following four
cause a loss of control, poor performance or dam- ratings are not exceeded:
age to brakes, axle, engine, transmission, steering, 1. GVWR
suspension, chassis structure or tires. 2. GTW
Safety chains must always be used between your 3. GAWR
vehicle and trailer. Always connect the chains to 4. Trailer tongue weight rating for that trailer
the frame or hook retainers of the vehicle hitch. hitch. (This requirement may limit the ability to
Cross the chains under the trailer tongue and always achieve the 10% to 15% range of trailer
allow enough slack for turning corners. tongue weight as a percentage of total trailer
(Continued) weight.)
Towing Requirements Tires replacement procedures. Replacing tires with a higher
load carrying capacity will not increase the vehicles
Do not attempt to tow a trailer while using a compact
GVWR and GAWR limits.
spare tire.
Towing Requirements Trailer Brakes
Proper tire inflation pressures are essential to the safe
and satisfactory operation of your vehicle. Refer to Do not interconnect the hydraulic brake system or
Tires General Information in Starting and Oper- vacuum system of your vehicle with that of the trailer.
ating for proper tire inflation procedures. This could cause inadequate braking and possible
personal injury.
Check the trailer tires for proper tire inflation pres-
sures before trailer usage. An electronically actuated trailer brake controller is 5
required when towing a trailer with electronically
Check for signs of tire wear or visible tire damage
actuated brakes. When towing a trailer equipped with
before towing a trailer. Refer to Tires General
a hydraulic surge actuated brake system, an electronic
Information in Starting and Operating for the
brake controller is not required.
proper inspection procedure.
Trailer brakes are recommended for trailers over
When replacing tires, refer to Tires General Infor-
1,000 lbs (454 kg) and required for trailers in excess of
mation in Starting and Operating for proper tire
2,000 lbs (907 kg).
CAUTION! WARNING! (Continued)

If the trailer weighs more than 1,000 lbs (454 kg) Towing any trailer will increase your stopping
loaded, it should have its own brakes and they distance. When towing you should allow for addi-
should be of adequate capacity. Failure to do this tional space between your vehicle and the vehicle
could lead to accelerated brake lining wear, higher in front of you. Failure to do so could result in an
brake pedal effort, and longer stopping distances. collision.
Towing Requirements Trailer Lights And Wiring

WARNING! Whenever you pull a trailer, regardless of the trailer size,
Do not connect trailer brakes to your vehicles stop lights and turn signals on the trailer are required for
hydraulic brake lines. It can overload your brake motoring safety.
system and cause it to fail. You might not have The Trailer Tow Package may include a four-pin or a
brakes when you need them and could have a seven-pin wiring harness. Use a factory approved trailer
collision. harness and connector.
(Continued) NOTE: Do not cut or splice wiring into the vehicles
wiring harness.
The electrical connections are all complete to the vehicle
but you must mate the harness to a trailer connector.
Refer to the following four-pin connector and seven-pin
connector illustrations.
Seven-Pin Connector
1 Battery 5 Ground
2 Backup Lamps 6 Left Stop/Turn
3 Right Stop/Turn 7 Running Lamps
4 Electric Brakes
Four-Pin Connector
1 Female Pins 4 Park
2 Male Pin 5 Left Stop/Turn
3 Ground 6 Right Stop/Turn
Towing Tips Electronic Speed Control If Equipped
Before setting out on a trip, practice turning, stopping
Do not use in hilly terrain or with heavy loads.
and backing the trailer in an area away from heavy
traffic. When using the speed control, if you experience speed
drops greater than 10 mph (16 km/h), disengage until
Automatic Transmission
you can get back to cruising speed.
The DRIVE gear can be selected when towing. However,
if frequent shifting occurs while in DRIVE, use the Use speed control in flat terrain and with light loads to
Electronic Range Select (ERS) shift control to select a maximize fuel efficiency.
lower gear range.
Cooling System
NOTE: Selecting a lower gear range while operating the To reduce potential for engine and transmission over-
vehicle under heavy operating conditions will improve heating, take the following actions:
performance and extend transmission life by reducing
City Driving
excessive shifting and heat build up. This action will also
When stopped for short periods of time, shift the trans-
provide better engine braking.
mission into NEUTRAL but do not increase engine idle
The automatic transmission fluid and filter should be speed.
changed if you REGULARLY tow a trailer for more than
Highway Driving
45 minutes of continuous operation. Refer to Mainte-
Reduce speed.
nance Schedule for the proper maintenance intervals.
Air Conditioning
CAUTION!
Turn off temporarily.
Towing this vehicle in violation of the above require-
RECREATIONAL TOWING ments can cause severe transmission damage. Dam-
(BEHIND MOTORHOME, ETC.) age from improper towing is not covered under the
Towing This Vehicle Behind Another Vehicle New Vehicle Limited Warranty.
Recreational towing is not allowed.
CAUTION!
5
DO NOT flat tow this vehicle. Damage to the drive-
train will result.
NOTE: This vehicle may be towed on a flatbed or

vehicle trailer provided all four wheels are OFF the
ground.
WHAT TO DO IN EMERGENCIES
CONTENTS
Hazard Warning Flashers . . . . . . . . . . . . . . . . 512 Securing The Spare Tire . . . . . . . . . . . . . . . . 527
If Your Engine Overheats . . . . . . . . . . . . . . . . 512 Road Tire Installation . . . . . . . . . . . . . . . . . 530
Jacking And Tire Changing . . . . . . . . . . . . . . . 513 Jump-Starting Procedure . . . . . . . . . . . . . . . . 532
Jack Location . . . . . . . . . . . . . . . . . . . . . . . 514 Preparations For Jump-Start . . . . . . . . . . . . . 533 6
Spare Tire Removal . . . . . . . . . . . . . . . . . . . 515 Jump-Starting Procedure . . . . . . . . . . . . . . . 534
To Access Spare Tire Winch Drive Nut . . . . . 515 Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . 536
Spare Tire Tools . . . . . . . . . . . . . . . . . . . . . 517
Shift Lever Override . . . . . . . . . . . . . . . . . . . 537
Spare Tire Removal Instructions . . . . . . . . . . 519
Towing A Disabled Vehicle . . . . . . . . . . . . . . . 538
Preparations For Jacking . . . . . . . . . . . . . . . 521
Without The Ignition Key . . . . . . . . . . . . . . 540
Jacking Instructions . . . . . . . . . . . . . . . . . . . 521
512 WHAT TO DO IN EMERGENCIES
HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS
The Hazard Warning flasher switch is located in the In any of the following situations, you can reduce the
lower center area of the instrument panel. potential for overheating by taking the appropriate ac-
tion.
Press the switch to turn on the Hazard Warning
flasher. When the switch is activated, all directional On the highways slow down.
turn signals will flash on and off to warn oncoming
In city traffic while stopped, place the transmission
traffic of an emergency. Press the switch a second time to
in NEUTRAL, but do not increase engine idle speed.
turn off the Hazard Warning flashers.
NOTE: There are steps that you can take to slow down
This is an emergency warning system and it should not
an impending overheat condition:
be used when the vehicle is in motion. Use it when your
vehicle is disabled and it is creating a safety hazard for If your air conditioner (A/C) is on, turn it off. The A/C
other motorists. system adds heat to the engine cooling system and
turning the A/C off can help remove this heat.
When you must leave the vehicle to seek assistance, the
Hazard Warning flashers will continue to operate even You can also turn the temperature control to maximum
though the ignition is placed in the OFF position. heat, the mode control to floor and the blower control
to high. This allows the heater core to act as a
NOTE: With extended use the Hazard Warning flashers
supplement to the radiator and aids in removing heat
may wear down your battery.
from the engine cooling system.
WHAT TO DO IN EMERGENCIES 513
JACKING AND TIRE CHANGING
CAUTION!
Driving with a hot cooling system could damage WARNING!
your vehicle. If temperature gauge reads H, pull
Do not attempt to change a tire on the side of the
over and stop the vehicle. Idle the vehicle with the air
vehicle close to moving traffic. Pull far enough off
conditioner turned off until the pointer drops back
the road to avoid the danger of being hit when
into the normal range. If the pointer remains on the
operating the jack or changing the wheel.
H, turn the engine off immediately, and call for
Being under a jacked-up vehicle is dangerous. The
service.
vehicle could slip off the jack and fall on you. You
could be crushed. Never put any part of your body
WARNING! under a vehicle that is on a jack. If you need to get 6
under a raised vehicle, take it to a service center
You or others can be badly burned by hot engine
where it can be raised on a lift.
coolant (antifreeze) or steam from your radiator. If
you see or hear steam coming from under the hood, Never start or run the engine while the vehicle is
do not open the hood until the radiator has had time on a jack.
to cool. Never try to open a cooling system pressure (Continued)
cap when the radiator or coolant bottle is hot.
The jack is designed to be used as a tool for
changing tires only. The jack should not be used to
lift the vehicle for service purposes. The vehicle
should be jacked on a firm level surface only.
Avoid ice or slippery areas.
Jack Location
The jack, jack handle and winch handle tools are stowed
behind the rear left side trim panel in the rear cargo area.
Turn the two cover latches to release the cover.
Jack And Tool Location
Remove the pouch containing the scissors jack, jack
handle, and tools.
Spare Tire Removal To Access Spare Tire Winch Drive Nut
The spare tire is stowed inside a protective cover located To access the spare tire winch drive nut and lower the
under the center of the vehicle between the front doors by spare tire, you will need to refer to one of the following
means of a cable winch mechanism. The spare tire center console configurations.
drive nut is located on the floor, under a plastic cap at
the front of the floor console or under front super console
forward bin liner.
Spare Tire Location

Super Console 1. Pull the lower drawer out from the rear of the floor
For vehicles equipped with the Super Console, the spare console.
tire winch assembly drive nut is located beneath the
console.
Lower Drawer
Super Console
1 Lower Drawer
2 Front Drawer
3 Front Drawer Liner
2. Open the front drawer to expose the storage compart- Premium/Base/Cargo Center Console
ment. Pull the Winch Cover assembly plug (if equipped) to
access the winch drive nut.
3. Remove the liner from the consoles storage compart-
ment to access the spare tire winch drive nut.
Winch Cover Assembly Plug (If Equipped)

Drive Nut Access
Spare Tire Tools
The tool pouch contains three pieces and can be as-
sembled into a spare tire hook; to remove the compact
spare tire/cover assembly from under the vehicle, or a
Winch T-handle; to raise/lower the compact spare tire/
cover assembly.
Assembling The Spare Tire Hook

A Spare Tire Hook/T-handle
B Extension 1
C Extension 2
Assembled T-handle
A Spare Tire Hook/T-handle
B Extension 1
C Extension 2
Spare Tire Removal Instructions 2. Rotate the nut to the left until the winch mechanism
The spare tire is located under the vehicle beneath the stops turning freely. This will allow enough slack in the
center console area. cable to allow you to pull the spare tire out from
underneath the vehicle.
CAUTION!
The winch mechanism is designed for use with the
winch T-handle only. Use of an air wrench or other
power tools is not recommended and can damage the
winch.
6
Spare Tire And Cover

1. Assemble the spare tire tools into a T-handle and place
the square end over the spare tire winch drive nut.
3. To remove the compact spare tire/cover assembly, 4. Stand the tire/cover assembly upright and remove the
assemble the winch T-handle extensions to form a spare wheel spacer by squeezing the winch retaining tabs
tire hook, and pull the spare tire out from under the together. Push the retainer through the spare tire to
vehicle. release it from the wheel.
Pulling Spare Tire Removing Wheel Spacer

NOTE: If either front tire is flat it may be necessary to
jack up the vehicle to remove the compact spare tire/
cover assembly from under the vehicle.
Preparations For Jacking 6. Block both the front and rear of the
wheel diagonally opposite the jacking
1. Park the vehicle on a firm, level surface. Avoid ice or
position. For example, if changing the
slippery areas.
right front tire, block the left rear
wheel.
WARNING!
Do not attempt to change a tire on the side of the
vehicle close to moving traffic, pull far enough off NOTE: Passengers should not remain in the vehicle
the road to avoid being hit when operating the jack when the vehicle is being jacked.
or changing the wheel.
Jacking Instructions
2. Turn on the Hazard Warning flasher.
WARNING! 6
3. Set the parking brake.
Carefully follow these tire changing warnings to
4. Place the shift lever into PARK. help prevent personal injury or damage to your
vehicle:
5. Turn OFF the ignition.
(Continued)

Always park on a firm, level surface as far from If working on or near a roadway, be extremely
the edge of the roadway as possible before raising careful of motor traffic.
the vehicle. To assure that spare tires, flat or inflated, are
Turn on the Hazard Warning flasher. securely stowed, spares must be stowed with the
Block the wheel diagonally opposite the wheel to valve stem facing the ground.
be raised.
Set the parking brake firmly and set an automatic
transmission in PARK; a manual transmission in
REVERSE.
Never start or run the engine with the vehicle on a
jack.
Do not let anyone sit in the vehicle when it is on a Jack Warning Label
jack.
Do not get under the vehicle when it is on a jack.
Only use the jack in the positions indicated and
for lifting this vehicle during a tire change.
(Continued)
CAUTION!
Do not attempt to raise the vehicle by jacking on
locations other than those indicated in the Jacking
Instructions for this vehicle.
NOTE: Refer to the Compact Spare Tire section of

Tires General Information for information about the
spare tire, its use, and operation.
1. Loosen (but do not remove) the wheel lug nuts by
turning them to the left one turn while the wheel is still Jack Locations
on the ground.
6
CAUTION!
2. There are two jack engagement locations on each side
of the vehicle body. These locations are on the sill flange Do not attempt to raise the vehicle by jacking on
of the vehicle body. locations other than those indicated.
Rear jack locations are between a pair of down-facing
tabs on the sill flange of the vehicle side body.
Front Jack Locations

NOTE: In some situations the jack may need to be
Rear Jacking Locations placed on its side in order to be pushed under the vehicle.
Front jack location is on the sill flange of the vehicle body Return the jack to its correct orientation once it is under
and is located 6 in (150 mm) from door edge. the vehicle.
4. Raise the vehicle by turning the jack screw to the right,
WARNING!
using the swivel wrench. Raise the vehicle only until the
Being under a jacked-up vehicle is dangerous. The tire just clears the surface and enough clearance is
vehicle could slip off the jack and fall on you. You obtained to install the spare tire. Minimum tire lift
could be crushed. Never get any part of your body provides maximum stability.
under a vehicle that is on a jack. If you need to get
under a raised vehicle, take it to a service center WARNING!
where it can be raised on a lift.
Raising the vehicle higher than necessary can make
the vehicle less stable. It could slip off the jack and
3. Place the wrench on the jack screw and turn to the
hurt someone near it. Raise the vehicle only enough
right until the jack head is properly engaged in the
to remove the tire.
described location. Do not raise the vehicle until you are 6
sure the jack is securely engaged.
5. Remove the wheel lug nuts, for vehicles with wheel
covers, remove the cover from the wheel by hand. Do not
pry the wheel cover off. Then pull the wheel off the hub.
6. Install the compact spare tire. Lightly tighten the lug
nuts.
CAUTION! WARNING!
Be sure to mount the spare tire with the valve stem To avoid the risk of forcing the vehicle off the jack,
facing outward. The vehicle could be damaged if the do not tighten the wheel nuts fully until the vehicle
spare tire is mounted incorrectly. has been lowered. Failure to follow this warning may
result in personal injury.
NOTE: Do not install the wheel cover on the compact

spare.
7. Lower the vehicle by turning the jack screw to the left.
8. Finish tightening the lug nuts. Push down on the
wrench while at the end of the handle for increased
leverage. Tighten the lug nuts in a star pattern until each
nut has been tightened twice. The correct wheel nut
tightness is 102 ft lbs (138 Nm). If in doubt about the
correct tightness, have them checked with a torque
wrench by your authorized dealer or at a service station.
Mounting Spare Tire
9. Lower the jack to its fully-closed position.
NOTE: Refer to the Spare Tire Tools section for
WARNING!
instructions on assembling the T-handle.
A loose tire or jack thrown forward in a collision or
12. Stow the jack, jack handle and winch handle tools
hard stop could endanger the occupants of the ve-
back in the stowage compartment.
hicle. Always stow the jack parts and the spare tire in
the places provided. Have the deflated (flat) tire 13. Check the compact spare tire pressure as soon as
repaired or replaced immediately. possible. Correct the tire pressure, as required.
Securing The Spare Tire
10. Place the deflated (flat) tire and compact spare tire
cover assembly in the rear cargo area. Do not stow the 1. Assemble the winch handle extensions to form a
deflated tire in the spare tire location. Have the full- T-handle and fit the winch T-handle over the drive nut.
sized tire repaired or replaced, as soon as possible. Rotate the nut to the left until the winch mechanism stops 6
turning freely. This will allow enough slack in the cable to
11. Stow the cable and wheel spacer before driving the
allow you to pull the wheel spacer out from under the
vehicle. Reassemble the winch handle extensions to form
vehicle.
a T and fit the winch T-handle over the drive nut.
Rotate the nut to the right until the winch mechanism
clicks at least three times.
3. Turn the compact spare tire so that the valve stem is
WARNING!
down, and place the tire into the spare tire/cover assem-
A loose compact spare tire/cover assembly, thrown bly. Slide the wheel spacer through the center of the
forward in a collision or hard stop could endanger wheel and spare tire/cover assembly, so that the two
the occupants of the vehicle. Always stow the com- retainer tabs snap out and engage the spare tire cover on
pact spare tire with the cover assembly in the place the opposite side.
provided.
CAUTION!
CAUTION! The compact spare tire/cover assembly must be used
when the compact spare tire is stored. Failure to use
The winch mechanism is designed for use with the
this cover could drastically reduce the life of the
winch T-handle only. Use of an air wrench or other
compact spare tire.
power tools is not recommended and can damage the
winch.
2. Assemble the winch handle extensions to form the

spare tire hook, and pull the wheel spacer from under the
vehicle.
5. Continue to rotate the nut to the right until you hear
WARNING!
the winch mechanism click three times. It cannot be
Verify that both retainer tabs of the wheel spacer overtightened. Check under the vehicle to ensure the
have been properly extended through the center of compact spare tire/cover assembly is positioned cor-
the wheel and spare tire/cover assembly. Failure to rectly against the underside of the vehicle.
properly engage both retainer tabs could result in
loss of the spare tire and cover assembly, which will CAUTION!
cause vehicle damage and may cause loss of vehicle
The winch mechanism is designed specifically to
control.
stow a compact spare tire only. Do not attempt to use
the winch to stow the full size flat tire, or any other
4. Using the winch T-handle, rotate the drive nut to the
full-size tire. Vehicle damage may result.
right until the compact spare tire/cover assembly is 6
drawn into place against the underside of the vehicle.
Road Tire Installation
Vehicles Equipped With Wheel Covers
1. Mount the road tire on the axle.
2. To ease the installation process for steel wheels with
wheel covers, install two lug nuts on the mounting studs
which are on each side of the valve stem. Install the lug
nuts with the cone shaped end of the nut toward the
wheel. Lightly tighten the lug nuts.
Tire And Wheel Cover Or Center Cap

1 Valve Stem 4 Wheel Cover
2 Valve Notch 5 Mounting Stud
3 Wheel Lug Nut
3. Align the valve notch in the wheel cover with the

valve stem on the wheel. Install the cover by hand,
snapping the cover over the two lug nuts. Do not use a
hammer or excessive force to install the cover.
4. Install the remaining lug nuts with the cone shaped correct tightness, have them checked with a torque
end of the nut toward the wheel. Lightly tighten the lug wrench by your authorized dealer or service station.
nuts.
7. After 25 miles (40 km) check the lug nut torque with a
torque wrench to ensure that all lug nuts are properly
WARNING!
seated against the wheel.
To avoid the risk of forcing the vehicle off the jack,
Vehicles Without Wheel Covers
do not tighten the wheel nuts fully until the vehicle
has been lowered. Failure to follow this warning may 1. Mount the road tire on the axle.
2. Install the remaining lug nuts with the cone shaped
end of the nut toward the wheel. Lightly tighten the lug
5. Lower the vehicle to the ground by turning the jack
handle counterclockwise.
nuts. 6
6. Finish tightening the lug nuts. Push down on the WARNING!
To avoid the risk of forcing the vehicle off the jack,
do not tighten the wheel nuts fully until the vehicle
nut has been tightened twice. The correct tightness of
has been lowered. Failure to follow this warning may
each lug nut is 102 ft/lbs (138 Nm). If in doubt about the
3. Lower the vehicle to the ground by turning the jack NOTE: When using a portable battery booster pack
handle counterclockwise. follow the manufacturers operating instructions and
precautions.
4. Finish tightening the lug nuts. Push down on the
CAUTION!
nut has been tightened twice. The correct tightness of Do not use a portable battery booster pack or any
each lug nut is 102 ft/lbs (138 Nm). If in doubt about the other booster source with a system voltage greater
correct tightness, have them checked with a torque than 12 Volts or damage to the battery, starter motor,
wrench by your authorized dealer or service station. alternator or electrical system may occur.
5. After 25 miles (40 km) check the lug nut torque with a
torque wrench to ensure that all lug nuts are properly WARNING!
seated against the wheel.
Do not attempt jump-starting if the battery is frozen.
JUMP-STARTING PROCEDURE It could rupture or explode and cause personal injury.
If your vehicle has a discharged battery it can be jump-
started using a set of jumper cables and a battery in
another vehicle or by using a portable battery booster
pack. Jump-starting can be dangerous if done improperly
so please follow the procedures in this section carefully.
Preparations For Jump-Start
WARNING!
The battery in your vehicle is located on the left side of
the engine compartment. Take care to avoid the radiator cooling fan when-
ever the hood is raised. It can start anytime the
ignition switch is on. You can be injured by
moving fan blades.
Remove any metal jewelry such as watch bands or
bracelets that might make an inadvertent electrical
contact. You could be seriously injured.
Batteries contain sulfuric acid that can burn your
skin or eyes and generate hydrogen gas which is
flammable and explosive. Keep open flames or 6
sparks away from the battery.
1. Set the parking brake, shift the automatic transmission

Positive Battery Post into PARK and turn the ignition to LOCK.
2. Turn off the heater, radio, and all unnecessary electri-
cal accessories.
3. If using another vehicle to jump-start the battery, park
CAUTION!
the vehicle within the jumper cables reach, set the
parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
WARNING! or the discharged vehicle.
Do not allow vehicles to touch each other as this
1. Connect the positive (+) end of the jumper cable to the
could establish a ground connection and personal
positive (+) post of the discharged vehicle.
injury could result.
2. Connect the opposite end of the positive (+) jumper
Jump-Starting Procedure cable to the positive (+) post of the booster battery.
3. Connect the negative end (-) of the jumper cable to the
WARNING!
negative (-) post of the booster battery.
Failure to follow this procedure could result in per-
4. Connect the opposite end of the negative (-) jumper
sonal injury or property damage due to battery ex-
cable to a good engine ground (exposed metal part of the
plosion.
discharged vehicles engine) away from the battery and
the fuel injection system.
8. Disconnect the opposite end of the positive (+) jumper
WARNING!
cable from the positive (+) post of the booster battery.
Do not connect the cable to the negative post (-) of the
9. Disconnect the positive (+) end of the jumper cable
discharged battery. The resulting electrical spark
from the positive (+) post of the discharged vehicle.
could cause the battery to explode and could result in
personal injury. If frequent jump-starting is required to start your vehicle
you should have the battery and charging system in-
5. Start the engine in the vehicle that has the booster spected at your authorized dealer.
battery, let the engine idle a few minutes, and then start
the engine in the vehicle with the discharged battery. CAUTION!
Once the engine is started, remove the jumper cables in
Accessories that can be plugged into the vehicle
the reverse sequence:
power outlets draw power from the vehicles battery,
6
6. Disconnect the negative (-) jumper cable from the even when not in use (i.e., cellular phones, etc.).
negative (-) post of the vehicle with the discharged Eventually, if plugged in long enough, the vehicles
battery. battery will discharge sufficiently to degrade battery
life and/or prevent the engine from starting.
7. Disconnect the negative end (-) of the jumper cable
from the negative (-) post of the booster battery.
FREEING A STUCK VEHICLE NOTE: To improve the vehicles traction when starting
If your vehicle becomes stuck in mud, sand or snow, it off in deep snow, sand or gravel, it may be desirable to
can often be moved by a rocking motion. Turn your switch the Electronic Stability Program (ESP) to Partial
steering wheel right and left to clear the area around the Off mode. Refer to Electronic Brake Control System in
front wheels. Then move the shift lever back and forth Starting and Operating for further information.
between DRIVE and REVERSE. Using minimal accelera-
tor pedal pressure to maintain the rocking motion, with- CAUTION!
out spinning the wheels, is most effective.
When rocking a stuck vehicle by moving be-
CAUTION! tween DRIVE and REVERSE, do not spin the
wheels faster than 15 mph (24 km/h), or drivetrain
Racing the engine or spinning the wheels may lead to damage may result.
transmission overheating and failure. Allow the en- Revving the engine or spinning the wheels too fast
gine to idle with the shift lever in NEUTRAL for at may lead to transmission overheating and failure.
least one minute after every five rocking-motion It can also damage the tires. Do not spin the
cycles. This will minimize overheating and reduce wheels above 30 mph (48 km/h) while in gear (no
the risk of transmission failure during prolonged transmission shifting occurring).
efforts to free a stuck vehicle.
2. Remove the shift lever override access cover located
WARNING!
near the top right of the shift lever in the instrument
Fast spinning tires can be dangerous. Forces gener- panel.
ated by excessive wheel speeds may cause damage, or
even failure, of the axle and tires. A tire could
explode and injure someone. Do not spin your vehi-
cles wheels faster than 30 mph (48 km/h) or for
longer than 30 seconds continuously without stop-
ping when you are stuck and do not let anyone near
a spinning wheel, no matter what the speed.
SHIFT LEVER OVERRIDE 6

If a malfunction occurs and the shift lever cannot be
moved out of the PARK position, you can use the
following procedure to temporarily move the shift lever:
Shift Lever Override Access Cover
1. Firmly apply the parking brake. 3. Turn the ignition switch to the ON/RUN position
without starting the engine.
4. Press and maintain firm pressure on the brake pedal.
5. Using a small screwdriver or similar small, push and 7. The vehicle may then be started in NEUTRAL.
hold the override release lever forward.
8. Reinstall the shift lever override access cover.
6. Move the shift lever to the NEUTRAL position.
TOWING A DISABLED VEHICLE
Towing Condition Wheels OFF the Ground ALL MODELS
Flat Tow NONE If transmission is operable:
Transmission in NEUTRAL
25 mph (40 km/h)max speed
Rear
Wheel lift 15 miles (24 km) max distance
Front OK
Flatbed ALL BEST METHOD
Proper towing or lifting equipment is required to prevent main structural members of the vehicle, not to bumpers
damage to your vehicle. Use only tow bars and other or associated brackets. State and local laws applying to
equipment designed for the purpose, following equip- vehicles under tow must be observed.
ment manufacturers instructions. Use of safety chains is
mandatory. Attach a tow bar or other towing device to
If you must use the accessories (wipers, defrosters, etc.) The manufacturer recommends towing your vehicle with
while being towed, the ignition must be in the ON/RUN all four wheels OFF the ground using a flatbed. If flatbed
position, not the ACC position. equipment is not available, and the transmission is
operable, the vehicle may be flat towed (with all four
CAUTION! wheels on the ground) under the following conditions:
Do not use sling type equipment when towing. The shift lever must be in NEUTRAL.
Damage to the fascia will occur.
The towing distance to be traveled must not exceed
When securing the vehicle to a flatbed truck, do 15 miles (24 km).
not attach to front or rear suspension components.
Damage to your vehicle may result from improper The towing speed must not exceed 25 mph (40 km/h).
towing. If the transmission is not operable, or the vehicle must 6
Do not push or tow this vehicle with another be towed faster than 25 mph (40 km/h) or farther than
vehicle as damage to the bumper fascia and trans- 15 miles (24 km), it must be towed with the front
mission may result. wheels OFF the ground (using a flatbed truck, or wheel
If the vehicle being towed requires steering, the lift equipment with the front wheels raised).
ignition switch must be in the ON/RUN position,
not the LOCK or ACC positions.
the ground) is not allowed, as transmission damage will
CAUTION!
occur. If rear towing is the only alternative, the front
Towing faster than 25 mph (40 km/h) or farther than wheels must be placed on a towing dolly. Proper towing
15 miles (24 km) with front wheels on the ground can equipment is necessary to prevent damage to the vehicle.
cause severe damage to the transmission. Such dam-
age is not covered by the New Vehicle Limited CAUTION!
Warranty.
Failure to follow these towing methods can cause
severe transmission damage. Such damage is not
Without The Ignition Key
covered by the New Vehicle Limited Warranty.
Special care must be taken when the vehicle is towed
with the ignition in the LOCK position. Flatbed towing is
the preferred towing method. However, if a flatbed
towing vehicle is not available, wheel lift towing equip-
ment may be used. Rear towing (with the front wheels on
MAINTAINING YOUR VEHICLE
CONTENTS
Engine Compartment 3.6L . . . . . . . . . . . . . 543 Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . 550
Onboard Diagnostic System OBD II . . . . . . 544 Engine Air Cleaner Filter . . . . . . . . . . . . . . . 551
Loose Fuel Filler Cap Message . . . . . . . . . . . 544 Exhaust System . . . . . . . . . . . . . . . . . . . . . 551
Emissions Inspection And Maintenance Maintenance-Free Battery . . . . . . . . . . . . . . 553
Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 545
Air Conditioner Maintenance . . . . . . . . . . . . 555
Replacement Parts . . . . . . . . . . . . . . . . . . . . . 547 7
Body Lubrication . . . . . . . . . . . . . . . . . . . . 557
Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . 547
Windshield Wiper Blades . . . . . . . . . . . . . . . 558
Maintenance Procedures . . . . . . . . . . . . . . . . . 547
Cooling System . . . . . . . . . . . . . . . . . . . . . 559
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 548
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
542 MAINTAINING YOUR VEHICLE
Automatic Transmission . . . . . . . . . . . . . . . 567 Fog Lamps . . . . . . . . . . . . . . . . . . . . . . . . . 584
Appearance Care And Protection From Rear Tail, Stop, Turn Signal, Side Marker
Corrosion . . . . . . . . . . . . . . . . . . . . . . . . . . 569 And Backup Lamps . . . . . . . . . . . . . . . . . . . 584
Cleaning The Instrument Panel Cupholders . . 574 Center High-Mounted Stop Lamp
(CHMSL) . . . . . . . . . . . . . . . . . . . . . . . . . . 585
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575
License Lamp . . . . . . . . . . . . . . . . . . . . . . . 586
Totally Integrated Power Module . . . . . . . . . 575
Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . 586
Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 582
Fluids, Lubricants And Genuine Parts . . . . . . . 587
Replacement Bulbs . . . . . . . . . . . . . . . . . . . . 582
Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . 583
Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
Headlamps . . . . . . . . . . . . . . . . . . . . . . . . 583
Front Park/Turn Signal Lamps . . . . . . . . . . . 584
MAINTAINING YOUR VEHICLE 543
ENGINE COMPARTMENT 3.6L
1 Air Filter 6 Engine Coolant Reservoir

2 Power Steering Fluid Reservoir 7 Engine Oil Dipstick
3 Brake Fluid Reservoir 8 Engine Oil Fill
4 Battery 9 Coolant Pressure Cap
5 Totally Integrated Power Module (Fuses) 10 Washer Fluid Reservoir
ONBOARD DIAGNOSTIC SYSTEM OBD II
CAUTION!
Your vehicle is equipped with a sophisticated onboard
diagnostic system called OBD II. This system monitors Prolonged driving with the MIL on could cause
the performance of the emissions, engine, and automatic further damage to the emission control system. It
transmission control systems. When these systems are could also affect fuel economy and driveability.
operating properly, your vehicle will provide excellent The vehicle must be serviced before any emissions
performance and fuel economy, as well as engine emis- tests can be performed.
sions well within current government regulations. If the MIL is flashing while the engine is running,
If any of these systems require service, the OBD II system severe catalytic converter damage and power loss
will turn on the Malfunction Indicator Light (MIL). It will soon occur. Immediate service is required.
will also store diagnostic codes and other information to
assist your service technician in making repairs. Al- Loose Fuel Filler Cap Message
though your vehicle will usually be drivable and not If the vehicle diagnostic system determines that the fuel
need towing, see your authorized dealer for service as filler cap is loose, improperly installed, or damaged, a
soon as possible. gASCAP message will display in the odometer or a
CHECK GASCAP message will be displayed in the
Electronic Vehicle Information Center (EVIC). Refer to
Electronic Vehicle Information Center (EVIC) in Un- For states that require an Inspection and Mainte-
derstanding Your Instrument Panel for further informa- nance (I/M), this check verifies the Malfunction
tion. Tighten the gas cap until a clicking sound is heard. Indicator Light (MIL) is functioning and is not
This is an indication that the gas cap is properly tight- on when the engine is running, and that the OBD II
ened. system is ready for testing.
Press the odometer reset button to turn the message off. Normally, the OBD II system will be ready. The OBD II
If the problem persists, the message will appear the next system may not be ready if your vehicle was recently
time the vehicle is started. This might indicate a damaged serviced, recently had a dead battery or a battery replace-
cap. If the problem is detected twice in a row, the system ment. If the OBD II system should be determined not
will turn on the MIL. Resolving the problem will turn the ready for the I/M test, your vehicle may fail the test.
MIL light off.
Your vehicle has a simple ignition key-actuated test,
EMISSIONS INSPECTION AND MAINTENANCE which you can use prior to going to the test station. To
PROGRAMS check if your vehicles OBD II system is ready, you must 7
In some localities, it may be a legal requirement to pass do the following:
an inspection of your vehicles emissions control system. 1. Turn the ignition switch to the ON position, but do not
Failure to pass could prevent vehicle registration. crank or start the engine.
2. If you crank or start the engine, you will have to start If your OBD II system is not ready, you should see your
this test over. authorized dealer or repair facility. If your vehicle was
recently serviced or had a battery failure or replacement,
3. As soon as you turn the ignition switch to the ON
you may need to do nothing more than drive your
position, you will see the MIL symbol come on as part of
vehicle as you normally would in order for your OBD II
a normal bulb check.
system to update. A recheck with the above test routine
4. Approximately 15 seconds later, one of two things will may then indicate that the system is now ready.
happen:
Regardless of whether your vehicles OBD II system is
a. The MIL will flash for about 10 seconds and then ready or not, if the MIL is illuminated during normal
return to being fully illuminated until you turn OFF vehicle operation you should have your vehicle serviced
the ignition or start the engine. This means that your before going to the I/M station. The I/M station can fail
vehicles OBD II system is not ready and you should your vehicle because the MIL is on with the engine
not proceed to the I/M station. running.
b. The MIL will not flash at all and will remain fully
illuminated until you turn OFF the ignition or start the
engine. This means that your vehicles OBD II system
is ready and you can proceed to the I/M station.
REPLACEMENT PARTS
WARNING!
Use of genuine MOPAR parts for normal/scheduled
maintenance and repairs is highly recommended to en- You can be badly injured working on or around a
sure the designed performance. Damage or failures motor vehicle. Only do service work for which you
caused by the use of non-MOPAR parts for maintenance have the knowledge and the proper equipment. If
and repairs will not be covered by the manufacturers you have any doubt about your ability to perform a
warranty. service job, take your vehicle to a competent me-
chanic.
DEALER SERVICE
Your authorized dealer has the qualified service person-
MAINTENANCE PROCEDURES
nel, special tools, and equipment to perform all service
The pages that follow contain the required maintenance
operations in an expert manner. Service Manuals are
services determined by the engineers who designed your
available which include detailed service information for
vehicle.
your vehicle. Refer to these Service Manuals before 7
attempting any procedure yourself. Besides those maintenance items specified in the fixed
maintenance schedule, there are other components which
NOTE: Intentional tampering with emissions control
may require servicing or replacement in the future.
systems may void your warranty and could result in civil
penalties being assessed against you.
Engine Oil
CAUTION!
Failure to properly maintain your vehicle or per- Checking Oil Level
form repairs and service when necessary could To assure proper engine lubrication, the engine oil must
result in more costly repairs, damage to other be maintained at the correct level. Check the oil level at
components or negatively impact vehicle perfor- regular intervals, such as every fuel stop. The best time to
mance. Immediately have potential malfunctions check the engine oil level is about five minutes after a
examined by an authorized Chrysler Group LLC fully warmed engine is shut OFF or before starting the
dealership or qualified repair center. engine after it has sat overnight.
Your vehicle has been built with improved fluids Checking the oil while the vehicle is on level ground will
that protect the performance and durability of improve the accuracy of the oil level readings. Maintain
your vehicle and also allow extended maintenance the oil level between the MIN and MAX markings on the
intervals. Do not use chemical flushes in these dipstick. Adding one quart of oil when the reading is at
components as the chemicals can damage your the MIN mark will result in a MAX reading on these
engine, transmission, power steering or air condi- engines.
tioning. Such damage is not covered by the New
Vehicle Limited Warranty. If a flush is needed
because of component malfunction, use only the
specified fluid for the flushing procedure.
American Petroleum Institute (API) Engine Oil
CAUTION!
Identification Symbol
Overfilling or underfilling will cause oil aeration, or This symbol means that the oil has
loss of oil pressure. This could damage your engine. been certified by the American
Petroleum Institute (API). The
Change Engine Oil manufacturer only recommends
The oil change indicator system will remind you that it is API Certified engine oils.
time to take your vehicle in for scheduled maintenance.
Refer to the Maintenance Schedule for further informa-
tion.
NOTE: Under no circumstances should oil change
intervals exceed 8,000 miles (13 000 km) or six months,
CAUTION!
whichever occurs first. Do not use chemical flushes in your engine oil as the 7
Engine Oil Selection chemicals can damage your engine. Such damage is
For best performance and maximum protection under all not covered by the New Vehicle Limited Warranty.
types of operating conditions, the manufacturer only
recommends engine oils that are API certified and meet Engine Oil Viscosity (SAE Grade)
the requirements of Chrysler Material Standard MS-6395. SAE 5W-30 engine oil is recommended for all operating
temperatures. This engine oil improves low temperature
starting and vehicle fuel economy. Your engine oil filler the engine oil. Engine oil is an engineered product and its
cap also shows the recommended engine oil viscosity for performance may be impaired by supplemental
your vehicle. additives.
For information on engine oil filler cap location, refer to Disposing Of Used Engine Oil And Oil Filters
Engine Compartment in Maintaining Your Vehicle Care should be taken in disposing of used engine oil and
for further information. oil filters from your vehicle. Used oil and oil filters,
indiscriminately discarded, can present a problem to the
Lubricants that do not have both the engine oil certifica-
environment. Contact your authorized dealer, service
tion mark and the correct SAE viscosity grade number,
station, or governmental agency for advice on how and
should not be used.
where used oil and oil filters can be safely discarded in
Synthetic Engine Oils your area.
You may use synthetic engine oils provided the recom-
Engine Oil Filter
mended oil quality requirements are met, and the recom-
The engine oil filter should be replaced with a new filter
mended maintenance intervals for oil and filter changes
at every engine oil change.
are followed.
Engine Oil Filter Selection
Materials Added To Engine Oil
The manufacturers engines have a full-flow type oil
The manufacturer strongly recommends against the ad-
filter. Use a filter of this type for replacement. The quality
dition of any additives (other than leak detection dyes) to
of replacement filters varies considerably. Only high
quality filters should be used to assure most efficient Engine Air Cleaner Filter Selection
service. MOPAR engine oil filters are a high quality oil The quality of replacement engine air cleaner filters
filter and are recommended. varies considerably. Only high quality filters should be
used to assure most efficient service. MOPAR engine air
Engine Air Cleaner Filter
cleaner filters are a high quality filter and are
recommended.
maintenance intervals.
Exhaust System
WARNING! The best protection against carbon monoxide entry into
the vehicle body is a properly maintained engine exhaust
The air induction system (air cleaner, hoses, etc.) can
system.
provide a measure of protection in the case of engine
backfire. Do not remove the air induction system (air If you notice a change in the sound of the exhaust system;
cleaner, hoses, etc.) unless such removal is necessary or if the exhaust fumes can be detected inside the vehicle;
for repair or maintenance. Make sure that no one is or when the underside or rear of the vehicle is damaged; 7
near the engine compartment before starting the have an authorized technician inspect the complete ex-
vehicle with the air induction system (air cleaner, haust system and adjacent body areas for broken, dam-
hoses, etc.) removed. Failure to do so can result in aged, deteriorated, or mispositioned parts. Open seams
serious personal injury. or loose connections could permit exhaust fumes to seep
into the passenger compartment. In addition, inspect the
CAUTION!
exhaust system each time the vehicle is raised for lubri-
cation or oil change. Replace as required. The catalytic converter requires the use of un-
leaded fuel only. Leaded gasoline will destroy the
WARNING! effectiveness of the catalyst as an emissions con-
trol device and may seriously reduce engine per-
Exhaust gases can injure or kill. They contain
formance and cause serious damage to the engine.
carbon monoxide (CO), which is colorless and
Damage to the catalytic converter can result if your
odorless. Breathing it can make you unconscious
vehicle is not kept in proper operating condition.
and can eventually poison you. To avoid breathing
In the event of engine malfunction, particularly
CO, refer to Safety Tips/Exhaust Gas in Things
involving engine misfire or other apparent loss of
To Know Before Starting Your Vehicle for further
performance, have your vehicle serviced promptly.
information.
Continued operation of your vehicle with a severe
A hot exhaust system can start a fire if you park
malfunction could cause the converter to overheat,
over materials that can burn. Such materials might
resulting in possible damage to the converter and
be grass or leaves coming into contact with your
vehicle.
exhaust system. Do not park or operate your ve-
hicle in areas where your exhaust system can
contact anything that can burn.
Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam-
verter will not require maintenance. However, it is image:
portant to keep the engine properly tuned to assure
Do not shut off the engine or interrupt the ignition,
proper catalyst operation and prevent possible catalyst
when the transmission is in gear and the vehicle is in
damage.
motion.
NOTE: Intentional tampering with emissions control
Do not try to start the engine by pushing or towing the
systems can result in civil penalties being assessed
vehicle.
against you.
Do not idle the engine with any spark plug wires
In unusual situations involving grossly malfunctioning
disconnected or removed, such as when diagnostic
engine operation, a scorching odor may suggest severe
testing, or for prolonged periods during very rough
and abnormal catalyst overheating. If this occurs, stop
idle or malfunctioning operating conditions.
the vehicle, turn off the engine and allow it to cool.
Service, including a tune-up to manufacturers specifica- Maintenance-Free Battery 7
tions, should be obtained immediately. Your vehicle is equipped with a maintenance-free battery.
You will never have to add water, nor is periodic main-
tenance required.
WARNING! CAUTION!
Battery fluid is a corrosive acid solution and can It is essential when replacing the cables on the
burn or even blind you. Do not allow battery fluid battery that the positive cable is attached to the
to contact your eyes, skin, or clothing. Do not lean positive post and the negative cable is attached to
over a battery when attaching clamps. If acid the negative post. Battery posts are marked posi-
splashes in eyes or on skin, flush the area imme- tive (+) and negative (-) and are identified on the
diately with large amounts of water. Refer to battery case. Cable clamps should be tight on the
Jump-Starting Procedures in What To Do In terminal posts and free of corrosion.
Emergencies for further information. If a fast charger is used while the battery is in
Battery gas is flammable and explosive. Keep the vehicle, disconnect both vehicle battery cables
flame or sparks away from the battery. Do not use before connecting the charger to the battery. Do
a booster battery or any other booster source with not use a fast charger to provide starting voltage.
an output greater than 12 Volts. Do not allow cable
clamps to touch each other.
Battery posts, terminals, and related accessories
contain lead and lead compounds. Wash hands
after handling.
Air Conditioner Maintenance
WARNING!
For best possible performance, your air conditioner
should be checked and serviced by an authorized dealer Use only refrigerants and compressor lubricants
at the start of each warm season. This service should approved by the manufacturer for your air condi-
include cleaning of the condenser fins and a system tioning system. Some unapproved refrigerants are
performance check. Drive belt tension should also be flammable and can explode, injuring you. Other
checked at this time. unapproved refrigerants or lubricants can cause
the system to fail, requiring costly repairs. Refer to
CAUTION! Warranty Information Book, located on the DVD,
for further warranty information.
Do not use chemical flushes in your air conditioning
system as the chemicals can damage your air condi- The air conditioning system contains refrigerant
under high pressure. To avoid risk of personal
tioning components. Such damage is not covered by
the New Vehicle Limited Warranty. injury or damage to the system, adding refrigerant
or any repair requiring lines to be disconnected 7
should be done by an experienced repairman.
Refrigerant Recovery And Recycling
WARNING!
R-134a air conditioning refrigerant is a hydrofluoro-
carbon (HFC) that is endorsed by the Environmental Do not remove the A/C air filter while the blower is
Protection Agency and is an ozone-saving product. How- operating or personal injury may result.
ever, the manufacturer recommends that air conditioning
service be performed by an authorized dealer, or other The A/C air filter is located in the fresh air inlet behind
authorized service facility, using recovery and recycling the glove box. Perform the following procedure to re-
equipment. place the filter:
NOTE: Use only manufacturer-approved A/C System 1. Open the glove compartment and remove all contents.
Sealers, Stop Leak Products, Seal Conditioners, Compres-
2. Push in on the sides of the glove compartment and
sor Oil, or Refrigerants.
lower the door.
A/C Air Filter
3. Pivot the glove compartment downward.
maintenance intervals. 4. Disengage the two retaining tabs that secure the filter
cover to the HVAC housing, and remove the cover.
CAUTION!
The A/C air filter is identified with an arrow to
indicate airflow direction through the filter. Failure
to properly install the filter will result in the need to
replace it more often.
7. Rotate the glove compartment door back into position.

Body Lubrication
Locks and all body pivot points, including such items as
seat tracks, door hinge pivot points and rollers, liftgate,
A/C Air Filter Replacement tailgate, sliding doors and hood hinges, should be lubri-
cated periodically with a lithium-based grease, such as
5. Remove the A/C air filter by pulling it straight out of
MOPAR Spray White Lube or equivalent, to assure
7
the housing.
quiet, easy operation and to protect against rust and
6. Install the A/C air filter with the arrow on the filter wear. Prior to the application of any lubricant, the parts
pointing toward the floor. When installing the filter concerned should be wiped clean to remove dust and
cover, make sure the retaining tabs fully engage the grit; after lubricating excess oil and grease should be
cover. removed. Particular attention should also be given to
hood latching components to ensure proper function. Avoid using the wiper blades to remove frost or ice from
When performing other underhood services, the hood the windshield. Keep the blade rubber out of contact with
latch, release mechanism and safety catch should be petroleum products such as engine oil, gasoline, etc.
cleaned and lubricated.
NOTE: Life expectancy of wiper blades varies depend-
The external lock cylinders should be lubricated twice a ing on geographical area and frequency of use. Poor
year, preferably in the Fall and Spring. Apply a small performance of blades may be present with chattering,
amount of a high quality lubricant such as MOPAR marks, water lines or wet spots. If any of these conditions
Lock Cylinder Lubricant or equivalent directly into the are present, clean the wiper blades or replace as neces-
lock cylinder. sary.
Windshield Wiper Blades Adding Washer Fluid
Clean the rubber edges of the wiper blades and the The fluid reservoir for the windshield washers and the
windshield periodically with a sponge or soft cloth and a rear window washer is shared. It is located in the engine
mild nonabrasive cleaner. This will remove accumula- compartment and should be checked at regular intervals.
tions of salt or road film. Fill the reservoir with windshield washer solvent (not
radiator antifreeze) and operate the system for a few
Operation of the wipers on dry glass for long periods
seconds to flush out any residual water.
may cause deterioration of the wiper blades. Always use
washer fluid when using the wipers to remove salt or dirt The washer fluid reservoir will hold a full gallon of fluid
from a dry windshield. when the Low Washer Fluid Light illuminates.
Cooling System
WARNING!
Commercially available windshield washer solvents WARNING!
are flammable. They could ignite and burn you. Care
When working near the radiator cooling fan, dis-
must be exercised when filling or working around
connect the fan motor lead or turn the ignition
the washer solution.
switch to the OFF position. The fan is temperature
controlled and can start at anytime the ignition
After the engine has warmed, operate the defroster for a
switch is in the ON position.
few minutes to reduce the possibility of smearing or
freezing the fluid on the cold windshield. MOPAR All You or others can be badly burned by hot engine
Weather Windshield Washer Solution or equivalent, used coolant (antifreeze) or steam from your radiator. If
with water as directed on the container, aids cleaning you see or hear steam coming from under the
action, reduces the freezing point to avoid line clogging, hood, do not open the hood until the radiator has
and is not harmful to paint or trim. had time to cool. Never try to open a cooling 7
system pressure cap when the radiator is hot.
Coolant Checks
Check the engine coolant (antifreeze) protection every
12 months (before the onset of freezing weather, where
applicable). If the engine coolant (antifreeze) is dirty or
rusty in appearance, the system should be drained, Cooling System Drain, Flush, And Refill
flushed and refilled with fresh coolant. Check the front of If the engine coolant (antifreeze) is dirty or contains a
the A/C condenser for any accumulation of bugs, leaves, considerable amount of sediment, clean and flush with a
etc. If dirty, clean by gently spraying water from a garden reliable cooling system cleaner. Follow with a thorough
hose vertically down the face of the condenser. rinsing to remove all deposits and chemicals. Properly
dispose of the old engine coolant (antifreeze) solution.
Check the coolant recovery bottle tubing for brittle rub-
ber, cracking, tears, cuts and tightness of the connection Refer to the Maintenance Schedule for the proper
at the bottle and radiator. Inspect the entire system for maintenance intervals.
leaks.
Selection Of Coolant
With the engine at normal operating temperature (but Use only the manufacturers recommended engine cool-
not running), check the cooling system pressure cap for ant (antifreeze). Refer Fluids, Lubricants and Genuine
proper vacuum sealing by draining a small amount of Parts in Maintaining Your Vehicle for further informa-
engine coolant (antifreeze) from the radiator drain cock. tion.
If the cap is sealing properly, the engine coolant (anti-
freeze) will begin to drain from the coolant recovery
bottle. DO NOT REMOVE THE COOLANT PRESSURE
CAP WHEN THE COOLING SYSTEM IS HOT.
Adding Coolant
CAUTION!
Your vehicle has been built with an improved engine
Mixing of engine coolant (antifreeze) other than coolant (antifreeze) that allows extended maintenance
specified Hybrid Organic Additive Technology intervals. This engine coolant (antifreeze) can be used up
(HOAT) engine coolant (antifreeze), may result in to five years or 104,000 miles (169 000 km) before
engine damage and may decrease corrosion pro- replacement. To prevent reducing this extended mainte-
tection. If a non-HOAT engine coolant (antifreeze) nance period, it is important that you use the same
is introduced into the cooling system in an emer- engine coolant (antifreeze) throughout the life of your
gency, it should be replaced with the specified vehicle.
engine coolant (antifreeze) as soon as possible.
Do not use water alone or alcohol based engine Please review these recommendations for using Hybrid
coolant (antifreeze) products. Do not use addi- Organic Additive Technology (HOAT) engine coolant
tional rust inhibitors or anti-rust products, as they (antifreeze). When adding engine coolant (antifreeze):
may not be compatible with the radiator engine The manufacturer recommends using MOPAR 7
coolant (antifreeze) and may plug the radiator. Antifreeze/Coolant 5 Year/100,000 Mile Formula
This vehicle has not been designed for use with HOAT (Hybrid Organic Additive Technology) or
Propylene Glycol-based engine coolant (anti- equivalent.
freeze). Use of Propylene Glycol-based engine
coolant (antifreeze) is not recommended.
Mix a minimum solution of 50% HOAT engine coolant Cooling System Pressure Cap
and distilled water. Use higher concentrations (not to The cap must be fully tightened to prevent the loss of
exceed 70%) if temperatures below 34F (37C) are engine coolant (antifreeze), and to ensure that engine
anticipated. coolant (antifreeze) will return to the radiator from the
coolant recovery bottle.
Use only high purity water such as distilled or deion-
ized water when mixing the water/engine coolant The cap should be inspected and cleaned if there is any
(antifreeze) solution. The use of lower quality water accumulation of foreign material on the sealing surfaces.
will reduce the amount of corrosion protection in the
engine cooling system. WARNING!
Please note that it is the owners responsibility to main- The warning words DO NOT OPEN HOT on the
tain the proper level of protection against freezing ac- cooling system pressure cap are a safety precaution.
cording to the temperatures occurring in the area where Never add engine coolant (antifreeze) when the
the vehicle is operated. engine is overheated. Do not loosen or remove the
cap to cool an overheated engine. Heat causes
NOTE: Mixing engine coolant (antifreeze) types will
pressure to build up in the cooling system. To
decrease the life of the engine coolant (antifreeze) and
prevent scalding or injury, do not remove the pres-
will require more frequent coolant changes.
sure cap while the system is hot or under pressure.
(Continued)
engine cold, the level of the engine coolant (antifreeze) in
the coolant recovery bottle should be between the ranges
Do not use a pressure cap other than the one indicated on the bottle.
specified for your vehicle. Personal injury or en-
gine damage may result. The radiator normally remains completely full, so there is
no need to remove the radiator cap unless checking for
Disposal Of Used Coolant engine coolant (antifreeze) freeze point or replacing the
Used ethylene glycol-based engine coolant (antifreeze) is engine coolant (antifreeze). Advise your service atten-
a regulated substance requiring proper disposal. Check dant of this. As long as the engine operating temperature
with your local authorities to determine the disposal is satisfactory, the coolant bottle only needs to be checked
rules for your community. To prevent ingestion by ani- once a month.
mals or children, do not store ethylene glycol-based When additional engine coolant (antifreeze) is needed to
engine coolant (antifreeze) in open containers or allow it maintain the proper level, it should be added to the
to remain in puddles on the ground. If ingested by a child coolant bottle. Do not overfill. 7
or pet, seek emergency assistance immediately. Clean up
any ground spills immediately. Points To Remember
Coolant Level NOTE: When the vehicle is stopped after a few miles (a
The coolant bottle provides a quick visual method for few kilometers) of operation, you may observe vapor
determining that the coolant level is adequate. With the coming from the front of the engine compartment. This is
normally a result of moisture from rain, snow, or high Maintain engine coolant (antifreeze) concentration at
humidity accumulating on the radiator and being vapor- 50% HOAT engine coolant (antifreeze) (minimum)
ized when the thermostat opens, allowing hot engine and distilled water for proper corrosion protection of
coolant (antifreeze) to enter the radiator. your engine, which contains aluminum components.
If an examination of your engine compartment shows no Make sure that the radiator and coolant recovery
evidence of radiator or hose leaks, the vehicle may be bottle overflow hoses are not kinked or obstructed.
safely driven. The vapor will soon dissipate.
Keep the front of the radiator clean. If your vehicle is
Do not overfill the coolant recovery bottle. equipped with air conditioning, also keep the front of
the condenser clean.
Check the engine coolant (antifreeze) freeze point in
the radiator and in the coolant recovery bottle. If Do not change the thermostat for Summer or Winter
engine coolant (antifreeze) needs to be added, contents operation. If replacement is ever necessary, install
of the coolant recovery bottle must also be protected ONLY the correct type thermostat. Other designs may
against freezing. result in unsatisfactory coolant performance, poor gas
mileage, and increased emissions.
If frequent engine coolant (antifreeze) additions are
required, or if the level in the coolant recovery bottle
does not drop when the engine cools, the cooling
system should be pressure tested for leaks.
Brakes Clean the top of the master cylinder area before removing
In order to assure brake system performance, all brake the cap. Add fluid to bring the level up to the top of the
system components should be inspected periodically. FULL mark on the side of the master cylinder reservoir.
Overfilling of fluid is not recommended because it may
cause leaking in the system.
WARNING! Add enough fluid to bring the level up to the require-
ments described on the brake fluid reservoir. With disc
Riding the brakes can lead to brake failure and
brakes, fluid level can be expected to fall as the brake
possibly a collision. Driving with your foot resting or
pads wear. However, low fluid level may be caused by a
riding on the brake pedal can result in abnormally
leak and a checkup may be needed.
high brake temperatures, excessive lining wear, and
possible brake damage. You would not have your full Use only manufacturers recommended brake fluid. Re-
braking capacity in an emergency. fer to Fluids, Lubricants, and Genuine Parts in Main-
taining Your Vehicle for further information.
7
Master Cylinder Brake Fluid Level Check
The fluid level in the master cylinder should be checked
when performing underhood services, or immediately if
the Brake System Warning Light indicates system
failure.

Use only manufacturers recommended brake To avoid contamination from foreign matter or
fluid. Refer to Fluids, Lubricants, and Genuine moisture, use only new brake fluid or fluid that
Parts in Maintaining Your Vehicle for further has been in a tightly closed container. Keep the
information. Using the wrong type of brake fluid master cylinder reservoir cap secured at all times.
can severely damage your brake system and/or Brake fluid in a open container absorbs moisture
impair its performance. The proper type of brake from the air resulting in a lower boiling point.
fluid for your vehicle is also identified on the This may cause it to boil unexpectedly during hard
original factory installed hydraulic master cylin- or prolonged braking, resulting in sudden brake
der reservoir. failure. This could result in a collision.
Overfilling the brake fluid reservoir can result in
(Continued) spilling brake fluid on hot engine parts, causing
the brake fluid to catch fire. Brake fluid can also
damage painted and vinyl surfaces, care should be
taken to avoid its contact with these surfaces.
(Continued)
Selection Of Lubricant
It is important that the proper lubricant is used in the
Do not allow petroleum based fluid to contami- transmission to assure optimum transmission perfor-
nate the brake fluid. Brake seal components could mance. Use only the manufacturers recommended trans-
be damaged, causing partial or complete brake mission fluid. Refer to Fluids, Lubricants, and Genuine
failure. This could result in a collision. Parts in Maintaining Your Vehicle for further informa-
tion. It is important that the transmission fluid be main-
Automatic Transmission tained at the prescribed level using the recommended
The automatic transmission and differential assembly are fluid. No chemical flushes should be used in any trans-
contained within a single housing. mission; only the approved lubricant may be used.
The fluid level in the automatic transmission should be
checked whenever the vehicle is serviced. Operation with
an improper fluid level will greatly reduce the life of the
transmission and the fluid. 7
The sixspeed transmission is equipped with a capped
dipstick tube. It is sealed and should not be tampered
with. Your authorized dealer has the necessary tools to
ensure that the fluid level is set properly.
CAUTION! CAUTION!
Using a transmission fluid other than the manufac- Do not use chemical flushes in your transmission as
turers recommended fluid may cause deterioration the chemicals can damage your transmission compo-
in transmission shift quality and/or torque converter nents. Such damage is not covered by the New
shudder. Using a transmission fluid other than the Vehicle Limited Warranty.
manufacturers recommended fluid will result in
more frequent fluid and filter changes. Refer to Fluid Level Check
Fluids, Lubricants, and Genuine Parts in Main- The six-speed automatic transmission is a sealed unit and
taining Your Vehicle for further information. has no dipstick. See your authorized dealer to have the
transmission fluid checked or serviced.
Special Additives
Fluid And Filter Changes
Automatic Transmission Fluid (ATF) is an engineered
product and its performance may be impaired by supple-
mental additives. Therefore, do not add any fluid addi-
tives to the transmission. The only exception to this If the transmission is disassembled for any reason, the
policy is the use of special dyes to aid in detecting fluid fluid and filter should be changed.
leaks. In addition, avoid using transmission sealers as
they may adversely affect seals.
Appearance Care And Protection From Corrosion The most common causes are:
Protection Of Body And Paint From Corrosion Road salt, dirt and moisture accumulation
Vehicle body care requirements vary according to geo-
Stone and gravel impact
graphic locations and usage. Chemicals that make roads
passable in snow and ice, and those that are sprayed on Insects, tree sap and tar
trees and road surfaces during other seasons, are highly
Salt in the air near seacoast localities
corrosive to the metal in your vehicle. Outside parking,
which exposes your vehicle to airborne contaminants, Atmospheric fallout/industrial pollutants
road surfaces on which the vehicle is operated, extreme
Washing
hot or cold weather and other extreme conditions will
have an adverse effect on paint, metal trim, and under- Wash your vehicle regularly. Always wash your ve-
body protection. hicle in the shade using MOPAR Car Wash or equiva-
lent, or a mild car wash soap, and rinse the panels
The following maintenance recommendations will enable
completely with clear water.
7
you to obtain maximum benefit from the corrosion
resistance built into your vehicle. If insects, tar or other similar deposits have accumu-
lated on your vehicle, use MOPAR Super Kleen Bug
What Causes Corrosion?
and Tar Remover or equivalent to remove.
Corrosion is the result of deterioration or removal of
paint and protective coatings from your vehicle.
Use a high quality cleaner wax, such as MOPAR Special Care
Cleaner Wax or equivalent to remove road film, stains
If you drive on salted or dusty roads or if you drive
and to protect your paint finish. Take care never to
near the ocean, hose off the undercarriage at least once
scratch the paint.
a month.
Avoid using abrasive compounds and power buffing
It is important that the drain holes in the lower edges
that may diminish the gloss or thin out the paint
of the doors and rocker panels be kept clear and open.
finish.
If you detect any stone chips or scratches in the paint,
CAUTION! touch them up immediately. The cost of such repairs is
considered the responsibility of the owner.
Do not use abrasive or strong cleaning materials
such as steel wool or scouring powder, which will If your vehicle is damaged due to a collision or similar
scratch metal and painted surfaces. cause which destroys the paint and protective coating,
Use of power washers exceeding 1,200 psi have your vehicle repaired as soon as possible. The
(8 274 kPa) can result in damage or removal of cost of such repairs is considered the responsibility of
paint and decals. the owner.
If you carry special cargo such as chemicals, fertilizers,
de-icer salt, etc., be sure that such materials are well
packaged and sealed.
If a lot of driving is done on gravel roads, consider
CAUTION!
mud or stone shields behind each wheel.
Do not use scouring pads, steel wool, a bristle brush,
Use MOPAR Touch Up Paint or equivalent on
or metal polishes. Do not use oven cleaner. These
scratches as soon as possible. Your authorized dealer
products may damage the wheels protective finish.
has touch up paint to match the color of your vehicle.
Avoid automatic car washes that use acidic solutions
Wheel And Wheel Trim Care or harsh brushes that may damage the wheels pro-
All wheels and wheel trim, especially aluminum and tective finish. Use only the approved MOPAR
chrome plated wheels, should be cleaned regularly with Wheel Cleaners or equivalent.
a mild soap and water to prevent corrosion.
Stain Repel Fabric Cleaning Procedure If
To remove heavy soil and/or excessive brake dust the
Equipped
following MOPAR wheel cleaners are recommended or
Stain Repel seats may be cleaned in the following man-
select a non-abrasive, non acidic cleaner.
ner: 7
For chrome wheels, use MOPAR Chrome Cleaner
Remove as much of the stain as possible by blotting
(Part# 04318013) or equivalent.
with a clean, dry towel.
For aluminum wheels, use MOPAR Wheel Cleaner
Blot any remaining stain with a clean, damp towel.
(Part# 04796239AB) or equivalent.
For tough stains, apply MOPAR Total Clean or Cleaning Interior Trim
equivalent, or a mild soap solution to a clean, damp Interior trim should be cleaned starting with a damp
cloth and remove the stain. Use a fresh, damp towel to cloth, a damp cloth with MOPAR Total Clean or equiva-
remove soap residue. lent, then MOPAR Spot & Stain Remover or equivalent
if absolutely necessary. Do not use harsh cleaners or
For grease stains, apply MOPAR Multi-Purpose
Armor All. Use MOPAR Total Clean or equivalent to
Cleaner or a equivalent high quality cleaner to a clean,
clean vinyl upholstery
damp cloth and remove the stain. Use a fresh, damp
towel to remove soap residue. Cleaning Leather Upholstery
MOPAR Total Clean or equivalent is specifically recom-
Do not use any harsh solvents or any other form of
mended for leather upholstery.
protectants on Stain Repel products.
Your leather upholstery can be best preserved by regular
Interior Care
cleaning with a damp soft cloth. Small particles of dirt
Instrument Panel Surfaces can act as an abrasive and damage the leather upholstery
The instrument panel cover has a low glare surface, and should be removed promptly with a damp cloth.
which minimizes reflections in the windshield. Do not Stubborn soils can be removed easily with a soft cloth
use protectants or other products which may cause and MOPAR Total Clean or equivalent. Care should be
undesirable reflections. Use soap and warm water to taken to avoid soaking your leather upholstery with any
restore the low glare surface. liquid. Please do not use polishes, oils, cleaning fluids,
solvents, detergents, or ammonia-based cleaners to clean To minimize the possibility of scratching the lenses and
your leather upholstery. Application of a leather condi- reducing light output, avoid wiping with a dry cloth. To
tioner is not required to maintain the original condition. remove road dirt, wash with a mild soap solution fol-
lowed by rinsing.
WARNING!
Do not use abrasive cleaning components, solvents, steel
Do not use volatile solvents for cleaning purposes. wool or other aggressive material to clean the lenses.
Many are potentially flammable, and if used in
Glass Surfaces
closed areas they may cause respiratory harm.
All glass surfaces should be cleaned on a regular basis
with MOPAR Glass Cleaner or equivalent or any com-
Cleaning Headlights
mercial household-type glass cleaner. Never use an abra-
Your vehicle has plastic headlights that are lightweight
sive type cleaner. Use caution when cleaning the inside
and less susceptible to stone breakage than glass head-
rear window equipped with electric defrosters or the
lights.
right rear quarter window equipped with the radio 7
Plastic is not as scratch resistant as glass and therefore antenna. Do not use scrapers or other sharp instruments
different lens cleaning procedures must be followed. that may scratch the elements.
When cleaning the rearview mirror, spray cleaner on the
towel or rag that you are using. Do not spray cleaner
directly on the mirror.
Cleaning Plastic Instrument Cluster Lenses Replace the seat belts if they appear frayed or worn, or if
The lenses in front of the instruments in this vehicle are the buckles do not work properly.
molded in clear plastic. When cleaning the lenses, care
Cleaning The Instrument Panel Cupholders
must be taken to avoid scratching the plastic.
Removal
1. Clean with a wet soft rag. A mild soap solution may be
Pull the flexible liner from the cupholder drawer starting
used, but do not use high alcohol content or abrasive
at one edge to ease removal.
cleaners. If soap is used, wipe clean with a clean damp
rag. Cleaning
The liner is top shelf dishwasher safe, or you may follow
2. Dry with a soft cloth.
the cleaning procedure below.
Seat Belt Maintenance
Soak the liner in a mixture of medium hot tap water and
Do not bleach, dye or clean the seat belts with chemical
one teaspoon of mild liquid dish soap. Let soak for
solvents or abrasive cleaners. This will weaken the fabric.
approximately 30 minutes. After 30 minutes, pull the
Sun damage can also weaken the fabric.
liner from the water and dip it back into the water about
If the seat belts need cleaning, use a mild soap solution or six times. This will loosen any remaining debris. Rinse
lukewarm water. Do not remove the belts from the car to the liner thoroughly under warm running water. Shake
wash them. Dry with a soft cloth. the excess water from the liner and dry the outer surfaces
with a clean soft cloth.
Installation
Place the liner into the cupholder drawer and press the
liner into place so that the retention tabs seat into the
corresponding openings in the drawer.
FUSES
Totally Integrated Power Module
The Totally Integrated Power Module is located in the
engine compartment near the battery. Refer to the appli-
cable Engine Compartment illustration in this section.
This center contains cartridge fuses and mini-fuses. A
label that identifies each component may be printed or
Totally Integrated Power Module
embossed on the inside of the cover.
7
CAUTION! Cartridge Mini-

Cavity Description
Fuse Fuse
When installing the Totally Integrated Power J1 40 Amp Power Folding Seat
Module cover, it is important to ensure the cover is Green
properly positioned and fully latched. Failure to J2 30 Amp Power Liftgate
do so may allow water to get into the Integrated Pink Module
Power Module, and possibly result in a electrical J3 30 Amp Rear Door Module
system failure. Pink
When replacing a blown fuse, it is important to J4 25 Amp Driver Door Node
use only a fuse having the correct amperage rating. Natural
The use of a fuse with a rating other than indicated J5 25 Amp Passenger Door Node
may result in a dangerous electrical system over- Natural
load. If a properly rated fuse continues to blow, it J6 40 Amp Antilock Brakes
indicates a problem in the circuit that must be Green Pump/Stability
corrected. Control System
J7 30 Amp Antilock Brakes
The numbers inside the TIPM cover correspond to the Pink Valve/Stability
following table. Control System
Cartridge Mini- Cartridge Mini-

Cavity Description Cavity Description
Fuse Fuse Fuse Fuse
J8 40 Amp Power Memory J14 40 Amp Rear Window
Green Seat If Equipped Green Defogger
J9 40 Amp Partial Zero Emis- J15 40 Amp Front Blower
Green sions Vehicle Motor/ Green
Flex Fuel If J17 40 Amp Starter Solenoid
Equipped Green
J10 30 Amp Headlamp Wash/ J18 20 Amp Powertrain Control
Pink Manifold Tuning Blue Module Trans Range
Valve If Equipped J19 60 Amp Radiator Fan
J11 30 Amp Power Sliding Door Yellow
Pink Module/AntiTheft J20 30 Amp Front Wiper LO/HI
Module If Equipped Pink
7
J12 30 Amp HVAC Rear Blower, J21 20 Amp Front/Rear Washer
Pink Radiator Fan Motor Blue
J13 60 Amp Ignition Off Draw J22 25 Amp Sunroof Module
Yellow (IOD) Main Natural

Fuse Fuse Fuse Fuse
M1 15 Amp Rear Center Brake M6 20 Amp Power Outlet #1
Blue Lamp/Brake Switch Yellow (ACC), Rain Sensor,
M2 20 Amp Trailer Lighting, Front Cigar Lighter (Instru-
Yellow Fog Lamps, Intelli- ment Panel or with
gent Battery Sensor Console Rear)
(IBS) M7 20 Amp Power Outlet #2
M3 20 Amp Front/Rear Axle Yellow (BATT/ACC SELECT)
Yellow Locker, Vacuum Center Seat or with
Pump Motor Console Rear
M4 10 Amp Trailer Tow M8 20 Amp Front Heated Seat If
Red Yellow Equipped
M5 25 Amp Inverter M9 20 Amp Rear Heated Seat If
Natural Yellow Equipped

Fuse Fuse Fuse Fuse
M10 15 Amp Ignition Off Draw M14 20 Amp Trailer Tow If
Blue Video System, Satel- Yellow Equipped
lite Radio, DVD, M15 20 Amp Rear View Mirror,
Hands-Free Module, Yellow Instrument Cluster,
Universal Garage Multi-Function
Door Opener, Vanity Control Switch, Tire
Lamp, Streaming Pressure Monitor,
Video Module If Glow Plug Module
Equipped If Equipped
M11 10 Amp Climate Control M16 10 Amp Airbag Module/
Red System Red Occupant Classifica-
M12 30 Amp Amplifier/Radio tion Module 7
Green M17 15 Amp Left Tail/License/
M13 20 Amp Instrument Cluster, Blue Park Lamp, Running
Yellow SIREN, Clock Mod- Lamps
ule, Multi-Function M18 15 Amp Right Tail/Park/Run
Control Switch If Blue Lamp
Equipped

Fuse Fuse Fuse Fuse
M19 25 Amp Powertrain M25 20 Amp Fuel Pump, Diesel
Natural Yellow Lift Pump If
M20 15 Amp Instrument Cluster Equipped
Blue Interior Light, Switch M26 10 Amp Power Mirror Switch,
Bank, Steering Red Driver Window
Column Module, Switch
Switch Steering M27 10 Amp Wireless Control
Wheel Red Module, Keyless
M21 20 Amp Powertrain Entry Module
Yellow M28 10 Amp Powertrain, Transmis-
M22 10 Amp Horn Red sion Control Module
Red M29 10 Amp Occupant Classifica-
M23 10 Amp Horn Red tion Module
Red M30 15 Amp Rear Wiper Module,
M24 25 Amp Rear Wiper Blue Power Folding Mirror
Natural M31 20 Amp Back-Up Lamps
Yellow

Fuse Fuse Fuse Fuse
M32 10 Amp Airbag Module, M36 20 Amp Power Outlet #3
Red THATCHUM If Yellow (Instrument Panel or
Equipped with Console Center)
M33 10 Amp Powertrain M37 10 Amp Antilock Brakes, Sta-
Red Red bility Control, Stop
M34 10 Amp Park Assist, Heater Lamp, Fuel Pump
Red Climate Control M38 25 Amp Door Lock/Unlock
Module, Headlamp Natural Motors, Liftgate
Wash, Compass, Rear Lock/Unlock Motors
Camera, Door Lamps,
The heated mirrors, lower instrument panel power outlet
Flashlight, Relay Die-
and removable floor console, when in the front position
sel Cabin Heater, Rad
are fused with self-resetting fuses that are only service-
7
Fan Diesel If
Equipped able by an authorized dealer. The power seats are fused
M35 10 Amp Heated Mirrors by a 30 Amp circuit breaker located under the drivers
Red seat. The power windows are fused by a 25 Amp circuit
breaker located under the instrument panel near the
steering column. If you experience temporary or perma- REPLACEMENT BULBS
nent loss of these systems, see your authorized dealer for
service. LIGHT BULBS Interior Bulb Number
Center & Rear Dome Lamp . . . . . . . . . . . . . . . . . 578
VEHICLE STORAGE
Center & Rear Reading Lamps . . . . . . . . . . . . . . . 578
If you are leaving your vehicle dormant for more than
Front Door Courtesy Lamp. . . . . . . . . . . . . . . . . . 578
21 days, you may want to take steps to protect your
Front Header Reading Lamps If Equipped . . . . . 578
battery. You may do the following: Instrument Cluster Lamps . . . . . . . . . . . . . . . . . PC74
Remove the 20 Amp mini-fuse in the Totally Inte- Liftgate Lamp(s) . . . . . . . . . . . . . . . . . . . . . . . . . 578
grated Power Module (TIPM) labeled Ignition-Off Overhead Console Reading Lamps . . . . . . . . . . PC579
Draw (IOD). Removable Console Lamp If Equipped . . . . . . . . 194
Visor Vanity Lamps . . . . . . . . . . . . . . . . . . . . 6501966
Or, disconnect the negative cable from the battery.
NOTE: For lighted switches, see your authorized dealer
Anytime you store your vehicle, or keep it out of for replacement instructions.
service for two weeks or more, run the air conditioning
system at idle for about five minutes in the fresh air All of the interior bulbs are glass wedge base or glass
and high blower setting. This will ensure adequate cartridge types. Aluminum base bulbs are not approved
system lubrication to minimize the possibility of com- and should not be used for replacement.
pressor damage when the system is started again.
LIGHT BULBS Exterior Bulb Number 2. Slide the red lock tab rearward on the connector, then
Headlamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . H11 depress the tab and remove the connector from the bulb.
Fog Lamp If Equipped . . . . . . . . . . . . . . . . PSX24W 3. Twist the headlamp bulb and pull the bulb from the
Front Side Marker, Park/Turn Signal . . . . . . . 3757A or headlamp housing.
PY27/7W
Rear Tail, Stop, Turn Signal Lamp . . . . . . . . . . . . LED 4. Install the new headlamp bulb and twist until locked
(Serviced at Authorized Dealer) into the headlamp housing.
Center High-Mounted Stop Lamp . . . . . . . . . . . . LED
(Serviced at Authorized Dealer) CAUTION!
Backup Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 3157
License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168 Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
BULB REPLACEMENT bulb comes in contact with an oily surface, clean the
Headlamps bulb with rubbing alcohol. 7
1. Raise the hood to access the rear of the headlamp 5. Connect the wiring connector to bulb and slide red
housing. lock tab forward.
Front Park/Turn Signal Lamps
CAUTION!
1. Raise the hood to access the rear of the headlamp
Do not touch the new bulb with your fingers. Oil
housing.
contamination will severely shorten bulb life. If the
2. Twist the turn signal socket and remove from the bulb comes in contact with an oily surface, clean the
headlamp housing, then pull the bulb out. bulb with rubbing alcohol.
3. Push the new bulb into the socket and reinstall the
2. Disconnect the wire harness from the bulb.
socket by twisting until locked into the headlamp
housing. 3. Reconnect the wiring harness to the new bulb and
reinstall by inserting the new bulb straight into the fog
Fog Lamps
lamp until it locks into place.
NOTE: Access to the fog lamp bulb is from the rear of
Rear Tail, Stop, Turn Signal, Side Marker and
the fascia. On the left rear side of the fascia, remove the
Backup Lamps
push pin and lower the hinged access door on the air
dam. 1. Raise the liftgate.
1. From behind the bumper fascia, or the access panel on
the air dam, squeeze the two tabs on the side of the bulb
socket and pull straight out from the fog lamp.
2. Remove the tail lamp assembly by removing the two NOTE:
screws from the inboard side. Use a fiber stick or similar If a screwdriver is used, make sure a soft material is
tool to gently pry the light on the outboard side to placed between the vehicle body and tool so not to
disengage the two ball studs. scratch the paint.
The PRY location is best closest to the studs while
dislodging them separately.
3. Twist the socket and remove from the lamp assembly.
4. Pull the bulb to remove it from the socket.
5. Replace the bulb, reinstall the socket, and reattach the
lamp assembly.
Center High-Mounted Stop Lamp (CHMSL)
The CHMSL uses LED lamps that are not serviceable
7
separately. The CHMSL must be replaced as an assembly.
See your authorized dealer.
License Lamp 2. Twist and remove the socket from the lamp assembly
The license plate lamp is located under the tailgate light and pull the bulb out to remove.
bar and above the license plate.
3. Push the bulb into the socket, twist the socket into the
1. Using a small screwdriver, press inward the locking lamp assembly and reinstall the lamp assembly into place
tab on the outboard side of the lamp assembly and pull ensuring the locking tab is secure.
down on the lamp assembly for removal.
FLUID CAPACITIES
U.S. Metric
Fuel (Approximate) 20 Gallons 76 Liters
Engine Oil with Filter
3.6L Engine (SAE 5W-30, API Certified) 6 Quarts 5.6 Liters
Cooling System *
3.6L Engine (MOPAR Engine Coolant/Antifreeze 13.4 Quarts 12.6 Liters
5 Year/100,000 Mile Formula or equivalent)
* Includes heater and coolant recovery bottle filled to MAX level. Add 2.9 Qts (2.8 L) if equipped with a rear
heater.
FLUIDS, LUBRICANTS AND GENUINE PARTS
Engine
Component Fluid, Lubricant, or Genuine Part
MOPAR Antifreeze/Coolant Five Year/100,000 Mile Formula HOAT
Engine Coolant
(Hybrid Organic Additive Technology) or equivalent.
Use API Certified SAE 5W-30 Engine Oil, meeting the requirements of
Engine Oil Chrysler Material Standard MS-6395. Refer to your oil filler cap for cor-
rect SAE grade.
Engine Oil Filter MOPAR Engine Oil Filter or equivalent.
Spark Plugs RER8ZWYCB4 (Gap 0.043 in [1.1 mm])
Fuel Selection 87 Octane
7
Chassis
Component Fluid, Lubricant, or Genuine Part
MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed
Automatic Transmission
ATF+4 product.
MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3
Brake Master Cylinder brake fluid is not available, then DOT 4 is acceptable. Use only recom-
mended brake fluids.
MOPAR Power Steering Fluid +4, MOPAR ATF+4 Automatic Trans-
Power Steering Reservoir
mission Fluid or equivalent licensed ATF+4 product.
M
A
MAINTENANCE SCHEDULES I
N
T
E
N
CONTENTS A
N
C
Maintenance Schedule . . . . . . . . . . . . . . . . . . 590 E
Required Maintenance Intervals . . . . . . . . . . 592 S

C
H
E
D
U
L
E
S
8
M 590 MAINTENANCE SCHEDULES
A
I MAINTENANCE SCHEDULE On Electronic Vehicle Information Center (EVIC)
N The Scheduled Maintenance services listed in this equipped vehicles, Oil Change Required will be dis-
T manual must be done at the times or mileages specified played in the EVIC and a single chime will sound,
E
N to protect your vehicle warranty and ensure the best indicating that an oil change is necessary.
A vehicle performance and reliability. More frequent main-
N Based on engine operation conditions, the oil change
tenance may be needed for vehicles in severe operating
C indicator message will illuminate. This means that ser-
E conditions, such as dusty areas and very short trip
vice is required for your vehicle. Have your vehicle
driving. Inspection and service should also be done
S anytime a malfunction is suspected. serviced as soon as possible, within the next 500 miles
C (805 km).
H The oil change indicator system will remind you that it is
E NOTE:
D time to take your vehicle in for scheduled maintenance.
The oil change indicator message will not monitor the
U
L On Non-EVIC equipped vehicles, CHAngE OIL will time since the last oil change. Change your vehicles
E flash in the instrument cluster odometer and a single oil if it has been six months since your last oil change,
S chime will sound, indicating that an oil change is neces- even if the oil change indicator message is NOT
8 sary. illuminated.
Change your engine oil more often if you drive your
vehicle off-road for an extended period of time.
MAINTENANCE SCHEDULES 591 M
A
Under no circumstances should oil change intervals the accuracy of the oil level reading. Add oil only I
exceed 8,000 miles (13 000 km) or six months, which- when the level is at or below the ADD, SAFE or MIN N
ever comes first. mark. T
E
Your authorized dealer will reset the oil change indicator Check the windshield washer solvent and add if N
A
message after completing the scheduled oil change. If a required. N
scheduled oil change is performed by someone other C
Once A Month E
than your authorized dealer, the message can be reset by
referring to the steps described under Electronic Vehicle Check tire pressure and look for unusual wear or S
Information Center (EVIC)/Oil Change Required in damage. C
Understanding Your Instrument Panel or under In- H
Inspect the battery and clean and tighten the terminals E
strument Cluster Description/Odometer/Trip Odom- D
as required.
eter in Understanding Your Instrument Panel for U
further information. Check the fluid levels of the coolant reservoir, brake L
E
master cylinder, and the power steering and add as S
At Each Stop For Fuel
needed. 8
Check the engine oil level about five minutes after a
Check all lights and other electrical items for correct
fully warmed engine is shut OFF. Checking the oil
operation.
level while the vehicle is on level ground will improve
A
I At Each Oil Change
CAUTION!
N
T Change the engine oil filter.
E
Failure to perform the required maintenance items
N Inspect the brake hoses and lines. may result in damage to the vehicle.
A
N Open the left and right door (slowly) and inspect for
Required Maintenance Intervals
C excessive dirt. If noise exist wipe clean and apply
E Refer to the Maintenance Schedules on the following
krytox lube to the door rollers.
pages for the required maintenance intervals.
S
C
H
E
D
U
L
E
S
8
A
8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service I
N
6 Months Maintenance Service Schedule T
Schedule Change the engine oil and engine oil filter. E
Change the engine oil and engine oil Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before N
filter. 16,000 miles (26 000 km). A
Rotate the tires, rotate at the first sign of If using your vehicle for any of the following: Dusty or off-road conditions. Inspect the N
irregular wear, even if it occurs before engine air cleaner filter; replace if necessary. C
Replace the air conditioning filter. E
8,000 miles (13 000 km).
Inspect the brake linings, replace if necessary.
S
Inspect exhaust system. Perform the first inspection at 16,000 miles (26 000 km) or
C
12 months. H
Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for E
damage, wear, improper looseness or end play; replace if necessary. D
U
L
E
S
Odometer Reading Date Odometer Reading Date
8
Repair Order # Dealer Code Repair Order # Dealer Code
Signature, Authorized Service Center Signature, Authorized Service Center

A
I 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service
N
T 18 Months Maintenance Schedule
E Service Schedule Change the engine oil and engine oil filter.
N Change the engine oil and engine oil Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before
A filter. 32,000 miles (52 000 km).
N Rotate the tires, rotate at the first sign of Replace the engine air cleaner filter.
C irregular wear, even if it occurs before Replace the air conditioning filter.
E Inspect the brake linings, replace if necessary.
24,000 miles (39 000 km).
Inspect the CV joints. Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
S
C Inspect exhaust system. damage, wear, improper looseness or end play; replace if necessary.
H
E
D
U
L
E
S
8 Odometer Reading Date Odometer Reading Date

A
N
30 Months Maintenance Schedule T
Service Schedule Change the engine oil and engine oil filter. E
filter. 48,000 miles (78 000 km). A
40,000 miles (65 000 km).
S
Inspect the CV joints.
C
Inspect exhaust system. H
U
L
E
S
8

A
N
A filter. 64,000 miles (104 000 km).
E Inspect the brake linings; replace if necessary.
56,000 miles (91 000 km).
Change the automatic transmission fluid and filter(s) if using your vehicle for any of the
S
following: police, taxi, fleet, or frequent trailer towing.
C
H Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
E damage, wear, improper looseness or end play; replace if necessary.
D
U
L
E
S

A
N
filter. 80,000 miles (130 000 km). A
72,000 miles (117 000 km).
Inspect the CV joints. Flush and replace the engine coolant at 60 months or 104,000 miles (169,000 km) whichever
S
Inspect exhaust system. comes first.
C
Inspect the brake linings, replace if necessary. H
U
L
E
S
8

A
N
A filter. 96,000 miles (156 000 km).
E Replace the spark plugs (3.6L Engine).
88,000 miles (143 000 km).
Inspect and replace PCV valve if necessary.
S
C
H Inspect the CV joints.
E Inspect exhaust system.
D Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
U damage, wear, improper looseness or end play; replace if necessary.
L
E
S

A
N
filter. 112,000 miles (182 000 km). A
104,000 miles (169 000 km).
Flush and replace the engine coolant at Inspect the brake linings, replace if necessary.
S
104,000 miles (169,000 km) or 60 months Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
C
whichever comes first. damage, wear, improper looseness or end play; replace if necessary. H
E
D
U
L
E
S
8

A
N
A filter. 128,000 miles (208 000 km).
E Inspect the brake linings, replace if necessary.
120,000 miles (195 000 km).
Inspect the CV joints. Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for
S
C Inspect exhaust system. damage, wear, improper looseness or end play; replace if necessary.
H Change the automatic transmission fluid
E and filter(s).
D Replace the accessory drive belt(s).
U
L
E
S

A
N
filter. 144,000 miles (234 000 km). A
136,000 miles (221 000 km).
S
Inspect the CV joints.
C
Inspect exhaust system. H
U
L
E
S
8

A
I 152,000 Miles (247,000 km) or
N
T 114 Months Maintenance
E Service Schedule
N Change the engine oil and engine oil
A filter.
N Rotate the tires, rotate at the first sign of
C irregular wear, even if it occurs before
E
152,000 miles (247 000 km).
S
C
H
E
D
U
L
E
S
8 Odometer Reading Date
Repair Order # Dealer Code
Signature, Authorized Service Center

A
WARNING! I
N
You can be badly injured working on or around a T
E
motor vehicle. Do only service work for which you N
have the knowledge and the right equipment. If A
you have any doubt about your ability to perform N
C
a service job, take your vehicle to a competent E
mechanic.
S
Failure to properly inspect and maintain your C
vehicle could result in a component malfunction H
and effect vehicle handling and performance. This E
D
could cause an accident. U
L
E
S
8
IF YOU NEED CONSUMER ASSISTANCE
CONTENTS
Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or
Vehicle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 607 Speech Impaired (TDD/TTY) . . . . . . . . . . . . 609
Prepare For The Appointment . . . . . . . . . . . 607 Service Contract . . . . . . . . . . . . . . . . . . . . . 609
Prepare A List . . . . . . . . . . . . . . . . . . . . . . 607 Warranty Information . . . . . . . . . . . . . . . . . . 610
Be Reasonable With Requests . . . . . . . . . . . . 607 MOPAR Parts . . . . . . . . . . . . . . . . . . . . . . . 610
If You Need Assistance . . . . . . . . . . . . . . . . . 607 Reporting Safety Defects . . . . . . . . . . . . . . . . 610
Chrysler Group LLC Customer Center . . . . . 608 In The 50 United States And Washington,
D.C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610
Chrysler Canada Inc. Customer Center . . . . . 608
In Canada . . . . . . . . . . . . . . . . . . . . . . . . . 611
9
In Mexico Contact . . . . . . . . . . . . . . . . . . . . 608
Publication Order Forms . . . . . . . . . . . . . . . . 611
606 IF YOU NEED CONSUMER ASSISTANCE
Department Of Transportation Uniform Tire Traction Grades . . . . . . . . . . . . . . . . . . . . . 613
Quality Grades . . . . . . . . . . . . . . . . . . . . . . . . 613
Temperature Grades . . . . . . . . . . . . . . . . . . 614
Treadwear . . . . . . . . . . . . . . . . . . . . . . . . . 613
IF YOU NEED CONSUMER ASSISTANCE 607
SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority.
YOUR VEHICLE At many authorized dealers, you may obtain a rental
vehicle at a minimal daily charge. If you need a rental, it
Prepare For The Appointment
is advisable to make these arrangements when you call
If youre having warranty work done, be sure to have the
for an appointment.
right papers with you. Take your warranty folder. All
work to be performed may not be covered by the IF YOU NEED ASSISTANCE
warranty. Discuss additional charges with the service The manufacturer and its authorized dealers are vitally
manager. Keep a maintenance log of your vehicles interested in your satisfaction. We want you to be happy
service history. This can often provide a clue to the with our products and services.
current problem.
Warranty service must be done by an authorized dealer.
Prepare A List We strongly recommend that you take the vehicle to an
Make a written list of your vehicles problems or the authorized dealer. They know your vehicle the best, and
specific work you want done. If youve had an accident are most concerned that you get prompt and high quality
or work done that is not on your maintenance log, let the service. The manufacturers authorized dealers have the
service advisor know. facilities, factory-trained technicians, special tools, and
Be Reasonable With Requests the latest information to ensure the vehicle is fixed
9
If you list a number of items and you must have your correctly and in a timely manner.
vehicle by the end of the day, discuss the situation with
This is why you should always talk to an authorized Chrysler Group LLC Customer Center
dealers service manager first. Most matters can be re- P.O. Box 218004
solved with this process. Auburn Hills, MI 483218004
Phone: (800) 4236343
If for some reason you are still not satisfied, talk to the
general manager or owner of the authorized dealer- Chrysler Canada Inc. Customer Center
ship. They want to know if you need assistance. P.O. Box 1621
Windsor, Ontario N9A 4H6
If an authorized dealership is unable to resolve the
Phone: (800) 4652001 English / (800) 3879983 French
concern, you may contact the manufacturers customer
center. In Mexico contact:
Av. Prolongacion Paseo de la Reforma, 1240
Any communication to the manufacturers customer cen-
Sante Fe C.P. 05109
ter should include the following information:
Mexico, D. F.
Owners name and address In Mexico City: 5081-7568
Outside Mexico City: 1-800-505-1300
Owners telephone number (home and office)
Authorized dealership name
Vehicle Identification Number (VIN)
Vehicle delivery date and mileage
Customer Assistance For The Hearing Or Speech the manufacturers service contracts. If you purchased a
Impaired (TDD/TTY) manufacturers service contract, you will receive Plan
To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail
manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date. If you
cation Devices for the Deaf) equipment at its customer have any questions about the service contract, call the
center. Any hearing or speech impaired customer, who manufacturers Service Contract National Customer
has access to a TDD or a conventional teletypewriter Hotline at 1-800-521-9922 (Canadian residents, call (800)
(TTY) in the United States, can communicate with the 4652001 English / (800) 3879983 French).
manufacturer by dialing 1800380CHRY.
The manufacturer will not stand behind any service
Canadian residents with hearing difficulties that require
contract that is not the manufacturers service contract. It
assistance can use the special needs relay service offered
is not responsible for any service contract other than the
by Bell Canada. For TTY teletypewriter users, dial 711
manufacturers service contract. If you purchased a ser-
and for Voice callers, dial 1 800 855-0511 to connect with
vice contract that is not a manufacturers service contract,
a Bell Relay Service operator.
and you require service after the manufacturers New
Service Contract Vehicle Limited Warranty expires, please refer to the
You may have purchased a service contract for a vehicle contract documents, and contact the person listed in
to help protect you from the high cost of unexpected those documents. 9
repairs after the manufacturers New Vehicle Limited
Warranty expires. The manufacturer stands behind only
We appreciate that you have made a major investment WARRANTY INFORMATION
when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the
has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group
training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
the ownership experience. Youll be pleased with their
sincere efforts to resolve any warranty issues or related MOPAR PARTS
concerns. MOPAR fluids, lubricants, parts, and accessories are
available from an authorized dealer. They are recom-
WARNING! mended for your vehicle in order to help keep the vehicle
operating at its best.
Engine exhaust, some of its constituents, and certain
vehicle components contain, or emit, chemicals REPORTING SAFETY DEFECTS
known to the State of California to cause cancer and
In the 50 United States and Washington, D.C.
birth defects, or other reproductive harm. In addi-
If you believe that your vehicle has a defect that could
tion, certain fluids contained in vehicles and certain
cause a crash or cause injury or death, you should
products of component wear contain, or emit, chemi-
immediately inform the National Highway Traffic Safety
cals known to the State of California to cause cancer
Administration (NHTSA) in addition to notifying the
and birth defects, or other reproductive harm.
manufacturer.
If NHTSA receives similar complaints, it may open an In Canada
If you believe that your vehicle has a safety defect, you
investigation, and if it finds that a safety defect exists in
a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme-
campaign. However, NHTSA cannot become involved in diately. Canadian customers who wish to report a safety
individual problems between you, your authorized defect to the Canadian government should contact Trans-
dealer, and the manufacturer. port Canada, Motor Vehicle Defect Investigations and
Recalls at 1-800-333-0510 or go to
To contact NHTSA, you may either call the Auto Safety
https://www.tc.gc.ca/roadsafety/
Hotline toll free at 18883274236 (TTY: 1800424
9153), or go to https://www.safercar.gov; or write to: PUBLICATION ORDER FORMS
Administrator, NHTSA, 1200 New Jersey Avenue, SE., To order the following manuals, you may use either the
West Building, Washington, D.C. 20590. You can also website or the phone numbers listed below. Visa, Mas-
obtain other information about motor vehicle safety from tercard, American Express, and Discover orders are ac-
https://www.safercar.gov. cepted. If you prefer mailing your payment, please call
for an order form.
NOTE: A street address is required when ordering
manuals (no P.O. Boxes).
9
Service Manuals Owners Manuals
These comprehensive Service Manuals provide the These Owners Manuals have been prepared with the
information that students and professional technicians assistance of service and engineering specialists to
need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve-
maintaining, servicing, and repairing Chrysler Group hicles. Included are starting, operating, emergency
LLC vehicles. A complete working knowledge of the and maintenance procedures as well as specifications,
vehicle, system, and/or components is written in capabilities and safety tips.
straightforward language with illustrations, diagrams,
and charts. Call toll free at:
Diagnostic Procedure Manuals 18008904038 (U.S.)
Diagnostic Procedure Manuals are filled with dia- 18003871143 (Canada)
grams, charts and detailed illustrations. These practi-
cal manuals make it easy for students and technicians Or
to find and fix problems on computer-controlled ve- Visit us on the Worldwide Web at:
hicle systems and features. They show exactly how to
find and correct problems the first time, using step-by- www.techauthority.com
step troubleshooting and drivability procedures,
proven diagnostic tests and a complete list of all tools
and equipment.
DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving
TIRE QUALITY GRADES habits, service practices, and differences in road charac-
The following tire grading categories were established by teristics and climate.
the National Highway Traffic Safety Administration. The
Traction Grades
specific grade rating assigned by the tires manufacturer
The Traction grades, from highest to lowest, are AA, A, B,
in each category is shown on the sidewall of the tires on
and C. These grades represent the tires ability to stop on
your vehicle.
wet pavement, as measured under controlled conditions
All passenger car tires must conform to Federal safety on specified government test surfaces of asphalt and
requirements in addition to these grades. concrete. A tire marked C may have poor traction perfor-
mance.
Treadwear
The Treadwear grade is a comparative rating, based on
WARNING!
the wear rate of the tire when tested under controlled
conditions on a specified government test course. For The traction grade assigned to this tire is based on
example, a tire graded 150 would wear one and one-half straight-ahead braking traction tests, and does not
times as well on the government course as a tire graded include acceleration, cornering, hydroplaning, or
100. The relative performance of tires depends upon the peak traction characteristics.
actual conditions of their use, however, and may depart 9
Temperature Grades
WARNING!
The temperature grades are A (the highest), B, and C,
representing the tires resistance to the generation of heat The temperature grade for this tire is established for
and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
controlled conditions on a specified indoor laboratory Excessive speed, under-inflation, or excessive load-
test wheel. Sustained high temperature can cause the ing, either separately or in combination, can cause
material of the tire to degenerate and reduce tire life, and heat buildup and possible tire failure.
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel, than the minimum required by law.
INDEX
10
616 INDEX
Adding Engine Coolant (Antifreeze) . . . . . . . . . . 561 Airbag Maintenance . . . . . . . . . . . . . . . . . . . . . . . 82
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . 491 Airbag, Side . . . . . . . . . . . . . . . . . . . . . . . . 74,76,79
Adding Washer Fluid . . . . . . . . . . . . . . . . . . . . . 558 Airbag, Window (Side Curtain) . . . . . . . . . . . 74,76,79
Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . 485 Alarm (Security Alarm) . . . . . . . . . . . . . . . . . . . . 17
Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . 211 Alarm Light . . . . . . . . . . . . . . . . . . . . . . . . . . . 294
Air Cleaner, Engine (Engine Air Cleaner Filter) . . . 551 Alterations/Modifications, Vehicle . . . . . . . . . . . . . 7
Air Conditioner Maintenance . . . . . . . . . . . . . . . 555 Antenna, Satellite Radio . . . . . . . . . . . . . . . . . . . 343
Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . 392 Anti-Lock Warning Light . . . . . . . . . . . . . . . . . . 289
Air Conditioning Controls . . . . . . . . . . . . . . . . . 392 Anti-Theft System . . . . . . . . . . . . . . . . . . . . . . . . 17
Air Conditioning Filter . . . . . . . . . . . . . . . . . 413,556 Antifreeze (Engine Coolant) . . . . . . . . . . . . . . 560,586
Air Conditioning Refrigerant . . . . . . . . . . . . . . . 555 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 563
Air Conditioning System . . . . . . . . . . . . . 392,400,555 Appearance Care . . . . . . . . . . . . . . . . . . . . . . . . 569
Air Conditioning System, Zone Control . . . . . . . . 392 Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 253
Air Conditioning, Operating Tips . . . . . . . . . . . . 413 Assist, Hill Start . . . . . . . . . . . . . . . . . . . . . . . . 449
Air Conditioning, Rear Zone . . . . . . . . . . . . . 397,408 Assistance Towing . . . . . . . . . . . . . . . . . . . . . . . 139
Air Pressure, Tires . . . . . . . . . . . . . . . . . . . . . . . 462 Auto Down Power Windows . . . . . . . . . . . . . . . . 39
Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70,79 Auto Up Power Windows . . . . . . . . . . . . . . . . . . 39
Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . 80 Automatic Dimming Mirror . . . . . . . . . . . . . . . . 113
Airbag Light . . . . . . . . . . . . . . . . . . . . 77,83,101,293 Automatic Door Locks . . . . . . . . . . . . . . . . . . . . . 35
INDEX 617
Automatic Headlights . . . . . . . . . . . . . . . . . . . . 199 Blind Spot Monitoring . . . . . . . . . . . . . . . . . . . . 117
Automatic Temperature Control (ATC) . . . . . . . . . 400 Body Mechanism Lubrication . . . . . . . . . . . . . . . 557
Automatic Transaxle Brake Assist System . . . . . . . . . . . . . . . . . . . . . . 444
Selection Of Lubricant . . . . . . . . . . . . . . . . . 588 Brake Control System, Electronic . . . . . . . . . . . . . 443
Automatic Transmission . . . . . . . . . . . . . . . . 422,567 Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 588
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . 568 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
Fluid and Filter Changes . . . . . . . . . . . . . . . 568 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . 565
Fluid Change . . . . . . . . . . . . . . . . . . . . . . . 568 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . 439
Fluid Level Check . . . . . . . . . . . . . . . . . . . . 568 Warning Light . . . . . . . . . . . . . . . . . . . . . . . 294
Fluid Type . . . . . . . . . . . . . . . . . . . . . . 567,588 Brake/Transmission Interlock . . . . . . . . . . . . . . . 424
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . 426 Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565
Special Additives . . . . . . . . . . . . . . . . . . . . . 568 Break-In Recommendations, New Vehicle . . . . . . . . 98
Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . 583
B-Pillar Location . . . . . . . . . . . . . . ..... . . . . . 457 Bulbs, Light . . . . . . . . . . . . . . . . . . . . . . . . . 103,582
Battery . . . . . . . . . . . . . . . . . . . . . ..... . . . . . 553
Jump Starting . . . . . . . . . . . . . ..... . . . . . 532 Calibration, Compass . . . . . . . . . . . . . . . . . . . . . 312
Keyless Transmitter Replacement (RKE) . . . . . 26 Camera, Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . 224
Saving Feature (Protection) . . . . ..... . . . . . 205 Capacities, Fluid . . . . . . . . . . . . . . . . . . . . . . . . 586
Belts, Seat . . . . . . . . . . . . . . . . . . . ..... . . . . . 100
10
618 INDEX
Caps, Filler Checks, Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491 Child Restraint . . . . . . . . . . . . . . . . . . . . . . . . 84,86
Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . 549 Child Restraint Tether Anchors . . . . . . . . . . . . . . . 89
Power Steering . . . . . . . . . . . . . . . . . . . . . . 438 Child Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 46
Radiator (Coolant Pressure) . . . . . . . . . . . . . 562 Child Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 569 Clean Air Gasoline . . . . . . . . . . . . . . . . . . . . . . . 483
Carbon Monoxide Warning . . . . . . . . . . . . . . . 99,486 Cleaning
Cargo (Vehicle Loading) . . . . . . . . . . . . . . . . . . . 260 Wheels . . . . . . . . . . . . . . . . . . . . . . . . . . . . 571
Cargo Compartment Climate Control . . . . . . . . . . . . . . . . . . . . . . . . . 392
Luggage Carrier . . . . . . . . . . . . . . . . . . . . . 270 Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322,332
Caution, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . . 51 Coat Hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . 125,391 Coin Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Center High Mounted Stop Light . . . . . . . . . . . . 585 Cold Weather Operation . . . . . . . . . . . . . . . . . . . 420
Chains, Tire . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 Compact Disc (CD) Maintenance . . . . . . . . . . . . . 391
Changing A Flat Tire . . . . . . . . . . . . . . . . . . . . . 513 Compact Spare Tire . . . . . . . . . . . . . . . . . . . . . . 465
Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . 453 Compass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
Check Engine Light Compass Calibration . . . . . . . . . . . . . . . . . . . . . 312
(Malfunction Indicator Light) . . . . . . . . . . . . . 291,545 Compass Variance . . . . . . . . . . . . . . . . . . . . . . . 313
Checking Your Vehicle For Safety . . . . . . . . . . . . . 99 Computer, Trip/Travel . . . . . . . . . . . . . . . . . . . . 310
INDEX 619
Connector Pressure Cap . . . . . . . . . . . . . . . . . . . . . . . . 562
UCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 346 Radiator Cap . . . . . . . . . . . . . . . . . . . . . . . 562
Universal Consumer Interface (UCI) . . . . . . . 346 Selection of Coolant (Antifreeze) . . . . 560,586,587
Conserving Fuel . . . . . . . . . . . . . . . . . . . . . . . . 308 Cupholders . . . . . . . . . . . . . . . . . . . . . . . . . 250,574
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Customer Assistance . . . . . . . . . . . . . . . . . . . . . 607
Console, Floor . . . . . . . . . . . . . . . . . . . . . . . . . . 261
Console, Overhead . . . . . . . . . . . . . . . . . . . . . . . 227 Data Recorder, Event . . . . . . . . . . . . . . . . . . . . . . 83
Console, Removable . . . . . . . . . . . . . . . . . . . . . . 265 Daytime Running Lights . . . . . . . . . . . . . . . . . . . 200
Contract, Service . . . . . . . . . . . . . . . . . . . . . . . . 609 Dealer Service . . . . . . . . . . . . . . . . . . . . . . . . . . 547
Coolant Pressure Cap (Radiator Cap) . . . . . . . . . . 562 Defroster, Rear Window . . . . . . . . . . . . . . . . . . . 269
Cooling System . . . . . . . . . . . . . . . . . . . . . . . . . 559 Defroster, Windshield . . . . . . . . . . . . . . . . . . 101,406
Adding Coolant (Antifreeze) . . . . . . . . . . . . . 561 Diagnostic System, Onboard . . . . . . . . . . . . . . . . 544
Coolant Capacity . . . . . . . . . . . . . . . . . . . . . 586 Dimmer Control . . . . . . . . . . . . . . . . . . . . . . . . 201
Coolant Level . . . . . . . . . . . . . . . . . . . . 559,563 Dipsticks
Disposal of Used Coolant . . . . . . . . . . . . . . . 563 Automatic Transmission . . . . . . . . . . . . . . . . 568
Drain, Flush, and Refill . . . . . . . . . . . . . . . . 560 Oil (Engine) . . . . . . . . . . . . . . . . . . . . . . . . 548
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 563 Power Steering . . . . . . . . . . . . . . . . . . . . . . 438
Points to Remember . . . . . . . . . . . . . . . . . . 563 Disabled Vehicle Towing . . . . . . . . . . . . . . . . . . . 538
10
620 INDEX
Disposal Electronic Stability Control (ESC) . . . . . . . . . . . . . 445
Antifreeze (Engine Coolant) . . . . . . . . . . . . . 563 Electronic Vehicle Information
Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 550 Center (EVIC) . . . . . . . . . . . . . . . . . . . . . . . 224,300
Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Emergency, In Case of
Door Locks, Automatic . . . . . . . . . . . . . . . . . . . . 35 Hazard Warning Flasher . . . . . . . . . . . . . . . 512
Door Opener, Garage . . . . . . . . . . . . . . . . . . . . . 231 Jacking . . . . . . . . . . . . . . . . . . . . . . . . . 513,521
Driving Jump Starting . . . . . . . . . . . . . . . . . . . . . . . 532
On Slippery Surfaces . . . . . . . . . . . . . . . . . . 434 Overheating . . . . . . . . . . . . . . . . . . . . . . . . 512
Through Flowing, Rising, or Shallow Emission Control System Maintenance . . . . . . . . . 545
Standing Water . . . . . . . . . . . . . . . . . . . . . . 435 Engine
Driving to Achieve Maximum Fuel Economy . . . . 308 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 551
Block Heater . . . . . . . . . . . . . . . . . . . . . . . . 422
E-85 Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 487 Break-In Recommendations . . . . . . . . . . . . . . 98
Economy (Fuel) Mode . . . . . . . . . . . . . . . . . . . . 424 Checking Oil Level . . . . . . . . . . . . . . . . . . . 548
Electric Remote Mirrors . . . . . . . . . . . . . . . . . . . 114 Compartment . . . . . . . . . . . . . . . . . . . . . . . 543
Electrical Power Outlets . . . . . . . . . . . . . . . . . . . 244 Compartment Identification . . . . . . . . . . . . . 543
Electronic Brake Control System . . . . . . . . . . . . . 443 Coolant (Antifreeze) . . . . . . . . . . . . . . . . . . 587
Brake Assist System . . . . . . . . . . . . . . . . . . . 444 Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . 559
Electronic Speed Control (Cruise Control) . . . . . . 212 Exhaust Gas Caution . . . . . . . . . . . . . . 51,99,486
INDEX 621
Flooded, Starting . . . . . . . . . . . . . . . . . . . . . 420 Exterior Folding Mirrors . . . . . . . . . . . . . . . . . . . 114
Fuel Requirements . . . . . . . . . . . . . . . . . 482,586 Exterior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Oil . . . . . . . . . . . . . . . . . . . . . . . . . 548,586,587
Oil Change Interval . . . . . . . . . . . . . . . . . . . 549 Fabric Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 572
Oil Disposal . . . . . . . . . . . . . . . . . . . . . . . . 550 Filler Location Fuel . . . . . . . . . . . . . . . . . . . . . . 293
Oil Filler Cap . . . . . . . . . . . . . . . . . . . . . . . 549 Filters
Oil Filter Disposal . . . . . . . . . . . . . . . . . . . . 550 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . 551
Oil Selection . . . . . . . . . . . . . . . . . . . . . 549,586 Air Conditioning . . . . . . . . . . . . . . . . . . 413,556
Oil Synthetic . . . . . . . . . . . . . . . . . . . . . . . . 550 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . 550,587
Overheating . . . . . . . . . . . . . . . . . . . . . . . . 512 Engine Oil Disposal . . . . . . . . . . . . . . . . . . . 550
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Temperature Gauge . . . . . . . . . . . . . . . . . . . 296 Flashers
Enhanced Accident Response Feature . . . . . . . . . . 80 Hazard Warning . . . . . . . . . . . . . . . . . . . . . 512
Entry System, Illuminated . . . . . . . . . . . . . . . . . . 19 Turn Signal . . . . . . . . . . . . . . . . . . . 103,286,584
Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 Flexible Fuel Vehicles
Event Data Recorder . . . . . . . . . . . . . . . . . . . . . . 83 Cruising Range . . . . . . . . . . . . . . . . . . . . . . 490
Exhaust Gas Caution . . . . . . . . . . . . . . . . . 51,99,486 Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . 489
Exhaust System . . . . . . . . . . . . . . . . . . . . . . . 99,551 Fuel Requirements . . . . . . . . . . . . . . . . . 487,488
Extender, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . . 70 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . 490
10
622 INDEX
Replacement Parts . . . . . . . . . . . . . . . . . . . . 490 Clean Air . . . . . . . . . . . . . . . . . . . . . . . . . . 483
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . 490 Conserving . . . . . . . . . . . . . . . . . . . . . . . . . 308
Flooded Engine Starting . . . . . . . . . . . . . . . . . . . 420 Economy Mode . . . . . . . . . . . . . . . . . . . . . . 424
Floor Console . . . . . . . . . . . . . . . . . . . . . . . . . . 261 Ethanol . . . . . . . . . . . . . . . . . . . . . . . . . . . 483
Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . 586 Filler Cap (Gas Cap) . . . . . . . . . . . . . . . 293,491
Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Filler Door (Gas Cap) . . . . . . . . . . . . . . . . . . 293
Fluid Level Checks Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . . 482
Automatic Transmission . . . . . . . . . . . . . . . . 568 Gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293
Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 565 Light . . . . . . . . . . . . . . . . . . . . . . . . . . 297,304
Power Steering . . . . . . . . . . . . . . . . . . . . . . 438 Materials Added . . . . . . . . . . . . . . . . . . . . . 485
Fluids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 587 Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . 483
Fluids, Lubricants and Genuine Parts . . . . . . . . . . 587 Octane Rating . . . . . . . . . . . . . . . . . . . . . . . 587
Fog Light Service . . . . . . . . . . . . . . . . . . . . . . . . 584 Requirements . . . . . . . . . . . . . . . . . . . . 482,586
Fog Lights . . . . . . . . . . . . . . . . . . . . . . . 201,286,584 Saver Mode . . . . . . . . . . . . . . . . . . . . . . . . 308
Fold in Floor (Stow n Go) Seating . . . . . . . . . . . 172 Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . 586
Freeing A Stuck Vehicle . . . . . . . . . . . . . . . . . . . 536 Fuel Optimizer . . . . . . . . . . . . . . . . . . . . . . . . . 308
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482 Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 308
Adding . . . . . . . . . . . . . . . . . . . . . . . . . . . 491 Fuel, Flexible . . . . . . . . . . . . . . . . . . . . . . . . . . . 487
Additives . . . . . . . . . . . . . . . . . . . . . . . . . . 485 Fueling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 491
INDEX 623
Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 575 Hands-Free Phone (Uconnect) . . . . . . . . . . . . . 125
Hazard
Garage Door Opener (HomeLink) . . . . . . . . . . . 231 Driving Through Flowing, Rising, or Shallow
Gas Cap (Fuel Filler Cap) . . . . . . . . . . . . 491,492,544 Standing Water . . . . . . . . . . . . . . . . . . . . . . 435
Gasoline (Fuel) . . . . . . . . . . . . . . . . . . . . . . . . . 482 Hazard Warning Flasher . . . . . . . . . . . . . . . . . . . 512
Conserving . . . . . . . . . . . . . . . . . . . . . . . . . 308 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . 168
Gasoline, Clean Air . . . . . . . . . . . . . . . . . . . . . . 483 Headlights
Gasoline, Reformulated . . . . . . . . . . . . . . . . . . . 483 Bulb Replacement . . . . . . . . . . . . . . . . . . . . 583
Gauges Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 573
Coolant Temperature . . . . . . . . . . . . . . . . . . 296 Lights On Reminder . . . . . . . . . . . . . . . . . . 200
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . 293 Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 583
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . 286 Time Delay . . . . . . . . . . . . . . . . . . . . . . . . . 199
Gear Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . 426 Washers . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Gear Select Lever Override . . . . . . . . . . . . . . . . . 537 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . 115
General Information . . . . . . . . . . . . . . . 17,28,155,482 Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Glass Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 573 Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Gross Axle Weight Rating . . . . . . . . . . . . . . . 493,496 Heater, Engine Block . . . . . . . . . . . . . . . . . . . . . 422
Gross Vehicle Weight Rating . . . . . . . . . . . . . 493,496 High Beam/Low Beam Select (Dimmer) Switch . . 204
10
624 INDEX
Hill Start Assist . . . . . . . . . . . . . . . . . . . . . . . . . 449 Integrated Power Module (Fuses) . . . . . . . . . . . . 575
Hitches Interior Appearance Care . . . . . . . . . . . . . . . . . . 572
Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . 500 Interior Lights . . . . . . . . . . . . . . . . . . . . . . . . . . 201
HomeLink (Garage Door Opener) Transmitter . . 231 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Hood Release . . . . . . . . . . . . . . . . . . . . . . . . . . 196
Hook, Coat . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260 Jack Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 514
Jack Operation . . . . . . . . . . . . . . . . . . . . . . . . . . 513
Ignition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . 532
Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12,13
Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . 13 Key-In Reminder . . . . . . . . . . . . . . . . . . . . . . . . . 15
Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . 19 Key, Programming . . . . . . . . . . . . . . . . . . . . . . . . 17
Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . 15 Key, Replacement . . . . . . . . . . . . . . . . . . . . . . . . 16
Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Key, Sentry (Immobilizer) . . . . . . . . . . . . . . . . . . . 15
Information Center, Vehicle . . . . . . . . . . . . . . . . . 300 Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . 20
Inside Rearview Mirror . . . . . . . . . . . . . . . . . . . . 112 Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Instrument Cluster . . . . . . . . . . . . . . . . . . . . 284,286
Instrument Panel and Controls . . . . . . . . . . . . . . 283 Lane Change Assist . . . . . . . . . . . . . . . . . . . . . . 204
Instrument Panel Cover . . . . . . . . . . . . . . . . . . . 572 Lap/Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . 56
Instrument Panel Lens Cleaning . . . . . . . . . . . . . 574
INDEX 625
LATCH Center Mounted Stop . . . . . . . . . . . . . . . . . . 585
(Lower Anchors and Tether for CHildren) . . . . . . . 89 Daytime Running . . . . . . . . . . . . . . . . . . . . 200
Latches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Dimmer Switch, Headlight . . . . . . . . . . . . . . 201
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 196 Electronic Stability Program (ESP) Indicator . . 448
Lead Free Gasoline . . . . . . . . . . . . . . . . . . . . . . 482 Engine Temperature Warning . . . . . . . . . . . . 298
Leaks, Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468 Fog . . . . . . . . . . . . . . . . . . . . . . . . . 201,286,584
Liftgate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Hazard Warning Flasher . . . . . . . . . . . . . . . 512
Light Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . 583
Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103,198 Headlights On Reminder . . . . . . . . . . . . . . . 200
Airbag . . . . . . . . . . . . . . . . . . . . . 77,83,101,293 High Beam Indicator . . . . . . . . . . . . . . . . . . 286
Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294 High Beam/Low Beam Select . . . . . . . . . . . . 204
Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 289 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . 19
Automatic Headlights . . . . . . . . . . . . . . . . . 199 Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
Back-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . 584 License . . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
Battery Saver . . . . . . . . . . . . . . . . . . . . . . . 205 Lights On Reminder . . . . . . . . . . . . . . . . . . 200
Brake Assist Warning . . . . . . . . . . . . . . . . . . 448 Low Fuel . . . . . . . . . . . . . . . . . . . . . . . 297,304
Brake Warning . . . . . . . . . . . . . . . . . . . . . . 294 Malfunction Indicator (Check Engine) . . . . . . 291
Bulb Replacement . . . . . . . . . . . . . . . . . 582,583 Oil Pressure . . . . . . . . . . . . . . . . . . . . . . . . 297
10
626 INDEX
Park . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 584 Loading Vehicle . . . . . . . . . . . . . . . . . . . 260,493,495
Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204 Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . 495
Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . 228 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 457
Rear Servicing . . . . . . . . . . . . . . . . . . . . . . . 584 Locks
Rear Tail . . . . . . . . . . . . . . . . . . . . . . . . . . . 584 Automatic Door . . . . . . . . . . . . . . . . . . . . . . 35
Seat Belt Reminder . . . . . . . . . . . . . . . . . . . 296 Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Security Alarm (Theft Alarm) . . . . . . . . . . . . 294 Lower Anchors and Tether for
Service . . . . . . . . . . . . . . . . . . . . . . . . . 582,583 CHildren (LATCH) . . . . . . . . . . . . . . . . . . . . . . . 89
Service Engine Soon Lubrication, Body . . . . . . . . . . . . . . . . . . . . . . . 557
(Malfunction Indicator) . . . . . . . . . . . . . . . . 291 Luggage Rack (Roof Rack) . . . . . . . . . . . . . . . . . 270
Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 584
Theft Alarm (Security Alarm) . . . . . . . . . . . . 294 Maintenance Free Battery . . . . . . . . . . . . . . . . . . 553
Tire Pressure Monitoring (TPMS) . . . . . . . . . 289 Maintenance Procedures . . . . . . . . . . . . . . . . . . . 547
Traction Control . . . . . . . . . . . . . . . . . . . . . 448 Maintenance Schedule . . . . . . . . . . . . . . . . . . . . 590
Turn Signal . . . . . . . . . . . . . . . . . . . . . . 103,584 Maintenance, Sunroof . . . . . . . . . . . . . . . . . . . . . 244
Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297 Malfunction Indicator Light (Check Engine) . . 291,545
Warning (Instrument Cluster Description) . . . 286 Manual, Service . . . . . . . . . . . . . . . . . . . . . . . . . 611
Load Leveling System . . . . . . . . . . . . . . . . . . . . 270 Map/Reading Lights . . . . . . . . . . . . . . . . . . . . . 228
Memory Feature (Memory Seat) . . . . . . . . . . . . . 191
INDEX 627
Memory Seat . . . . . . . . . . . . . . . . . . . . . . . . 115,191 Navigation System (Uconnect gps) . . . . . . . . . . 224
Methanol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 New Vehicle Break-In Period . . . . . . . . . . . . . . . . 98
Mini-Trip Computer . . . . . . . . . . . . . . . . . . . . . . 310
Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Occupant Restraints . . . . . . . . . . . . . . . . . . . 52,76,80
Automatic Dimming . . . . . . . . . . . . . . . . . . 113 Occupant Restraints (Sedan) . . . . . . . . . . . . . 74,76,79
Electric Remote . . . . . . . . . . . . . . . . . . . . . . 114 Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Exterior Folding . . . . . . . . . . . . . . . . . . . . . 114 Oil Change Indicator . . . . . . . . . . . . . . . . 288,289,307
Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Oil Change Indicator, Reset . . . . . . . . . . . 288,289,307
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Oil, Engine . . . . . . . . . . . . . . . . . . . . . . . . . 548,587
Outside . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 586
Rearview . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Change Interval . . . . . . . . . . . . . . . . . . . . . 549
Vanity . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 Checking . . . . . . . . . . . . . . . . . . . . . . . . . . 548
Mode Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 550
Fuel Saver . . . . . . . . . . . . . . . . . . . . . . . . . 308 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . 550,587
Modifications/Alterations, Vehicle . . . . . . . . . . . . . 7 Filter Disposal . . . . . . . . . . . . . . . . . . . . . . . 550
Monitor, Tire Pressure System . . . . . . . . . . . . . . . 473 Identification Logo . . . . . . . . . . . . . . . . . . . 549
Mopar Parts . . . . . . . . . . . . . . . . . . . . . . . . . 547,610 Materials Added to . . . . . . . . . . . . . . . . . . . 550
MTBE/ETBE . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 Recommendation . . . . . . . . . . . . . . . . . . 549,586
Multi-Function Control Lever . . . . . . . . . . . . . . . 203 Synthetic . . . . . . . . . . . . . . . . . . . . . . . . . . 550
10
628 INDEX
Viscosity . . . . . . . . . . . . . . . . . . . . . . . . 549,586 Power
Onboard Diagnostic System . . . . . . . . . . . . . . 544,545 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . 34
Opener, Garage Door (HomeLink) . . . . . . . . . . . 231 Lift Gate . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Operator Manual (Owners Manual) . . . . . . . . . . . . 4 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Outside Rearview Mirrors . . . . . . . . . . . . . . . 112,113 Outlet (Auxiliary Electrical Outlet) . . . . . . . . 244
Overhead Console . . . . . . . . . . . . . . . . . . . . . . . 227 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
Overhead Travel Information Center . . . . . . . . . . 227 Sliding Door . . . . . . . . . . . . . . . . . . . . . . . . . 42
Overheating, Engine . . . . . . . . . . . . . . . . . . . 296,512 Steering . . . . . . . . . . . . . . . . . . . . . . . . 437,438
Owners Manual (Operator Manual) . . . . . . . . . 4,611 Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Panic Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Power Steering Fluid . . . . . . . . . . . . . . . . . . . . . 588
Park Sense System, Rear . . . . . . . . . . . . . . . . . . . 215 Pregnant Women and Seat Belts . . . . . . . . . . . . . . 69
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . 439 Preparation for Jacking . . . . . . . . . . . . . . . . . . . . 521
Pedals, Adjustable . . . . . . . . . . . . . . . . . . . . . . . 211 Pretensioners
Personal Settings . . . . . . . . . . . . . . . . . . . . . . . . 314 Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Pets, Transporting . . . . . . . . . . . . . . . . . . . . . . . . 95 Programmable Electronic Features . . . . . . . . . . . . 314
Phone, Cellular . . . . . . . . . . . . . . . . . . . . . . . . . 125
Phone, Hands-Free (Uconnect) . . . . . . . . . . . . . 125 Radial Ply Tires . . . . . . . . . . . . . . . . . . . . . . . . . 464
Placard, Tire and Loading Information . . . . . . . . . 457 Radiator Cap (Coolant Pressure Cap) . . . . . . . 560,562
INDEX 629
Radio Operation . . . . . . . . . . . . . . . . . . . . . . . . 391 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . 547
Radio Remote Controls . . . . . . . . . . . . . . . . . . . . 389 Replacement Tires . . . . . . . . . . . . . . . . . . . . . . . 469
Rear Air Conditioning . . . . . . . . . . . . . . . . . 397,408 Reporting Safety Defects . . . . . . . . . . . . . . . . . . . 610
Rear Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . 224 Resetting Oil Change Indicator . . . . . . . . . 288,289,307
Rear Cross Path . . . . . . . . . . . . . . . . . . . . . . . . . 123 Restraint, Head . . . . . . . . . . . . . . . . . . . . . . . . . 168
Rear Heater . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397 Restraints, Child . . . . . . . . . . . . . . . . . . . . . . . 84,88
Rear Park Sense System . . . . . . . . . . . . . . . . . . . 215 Rocking Vehicle When Stuck . . . . . . . . . . . . . . . . 536
Rear Window Defroster . . . . . . . . . . . . . . . . . . . 269 Roof Rack (Luggage Rack) . . . . . . . . . . . . . . . . . 270
Rearview Mirrors . . . . . . . . . . . . . . . . . . . . . . . . 112 Rotation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Reclining Front Seats . . . . . . . . . . . . . . . . . . . . . 167
Recorder, Event Data . . . . . . . . . . . . . . . . . . . . . . 83 Safety Checks Inside Vehicle . . . . . . . . . . . . . . . . 100
Recreational Towing . . . . . . . . . . . . . . . . . . . . . . 509 Safety Checks Outside Vehicle . . . . . . . . . . . . . . . 103
Reformulated Gasoline . . . . . . . . . . . . . . . . . . . . 483 Safety Defects, Reporting . . . . . . . . . . . . . . . . . . 610
Reminder, Seat Belt . . . . . . . . . . . . . . . . . . . . . . . 68 Safety Information, Tire . . . . . . . . . . . . . . . . . . . 452
Remote Keyless Entry (RKE) . . . . . . . . . . . . . . . . . 20 Safety Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Remote Sound System (Radio) Controls . . . . . . . . 389 Safety, Exhaust Gas . . . . . . . . . . . . . . . . . . . . . 51,99
Remote Starting System . . . . . . . . . . . . . . . . . . . . 29 Satellite Radio Antenna . . . . . . . . . . . . . . . . . . . 343
Removable Floor Console . . . . . . . . . . . . . . . . . . 265 Schedule, Maintenance . . . . . . . . . . . . . . . . . . . . 590
Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . 16 Seat Belt Maintenance . . . . . . . . . . . . . . . . . . . . 574
10
630 INDEX
Seat Belt Reminder . . . . . . . . . . . . . . . . . . . . . . . 68 Security Alarm (Theft Alarm) . . . . . . . . . . . . . . . . 17
Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 52,100 Selection of Coolant (Antifreeze) . . . . . . . . . . 560,587
Adjustable Shoulder Belt . . . . . . . . . . . . . . . . 61 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . 15
Adjustable Upper Shoulder Anchorage . . . . . . 61 Sentry Key Programming . . . . . . . . . . . . . . . . . . . 17
And Pregnant Women . . . . . . . . . . . . . . . . . . 69 Sentry Key Replacement . . . . . . . . . . . . . . . . . . . 16
Child Restraint . . . . . . . . . . . . . . . . . . . 84,85,86 Service Assistance . . . . . . . . . . . . . . . . . . . . . . . 607
Extender . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 Service Contract . . . . . . . . . . . . . . . . . . . . . . . . . 609
Front Seat . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Service Engine Soon Light
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . 100 (Malfunction Indicator) . . . . . . . . . . . . . . . . . . . . 291
Pretensioners . . . . . . . . . . . . . . . . . . . . . . . . 64 Service Manuals . . . . . . . . . . . . . . . . . . . . . . . . . 611
Rear Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Setting the Clock . . . . . . . . . . . . . . . . . . . . . 322,332
Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Settings, Personal . . . . . . . . . . . . . . . . . . . . . . . . 314
Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . 166 Shift Lever Override . . . . . . . . . . . . . . . . . . . . . . 537
Fold in Floor (Stow n Go) . . . . . . . . . . . . . . 172 Shoulder Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Heated . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Side Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . 191 Signals, Turn . . . . . . . . . . . . . . . . 103,203,204,286,584
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 Sliding Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Reclining . . . . . . . . . . . . . . . . . . . . . . . . . . 167 Slippery Surfaces, Driving On . . . . . . . . . . . . . . . 434
Stow n Go (Fold in Floor) . . . . . . . . . . . . . . 172 Snow Chains (Tire Chains) . . . . . . . . . . . . . . . . . 470
INDEX 631
Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254,582
Spare Tire . . . . . . . . . . . . . . . . . . . . . . . 465,466,515 Storage Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 254
Speed Control (Cruise Control) . . . . . . . . . . . . . . 212 Storage, Vehicle . . . . . . . . . . . . . . . . . . . . . . 412,582
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 293 Storing Your Vehicle . . . . . . . . . . . . . . . . . . . . . . 582
Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419 Stow n Go (Fold in Floor) Seats . . . . . . . . . . . . . 172
Automatic Transmission . . . . . . . . . . . . . . . . 419 Sun Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Cold Weather . . . . . . . . . . . . . . . . . . . . . . . 420 Sunglasses Storage . . . . . . . . . . . . . . . . . . . . . . . 228
Engine Fails to Start . . . . . . . . . . . . . . . . . . 420 Sunroof Maintenance . . . . . . . . . . . . . . . . . . . . . 244
Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Supplemental Restraint System - Airbag . . . . . . . . 70
Starting and Operating . . . . . . . . . . . . . . . . . . . . 419 Synthetic Engine Oil . . . . . . . . . . . . . . . . . . . . . . 550
Starting Procedures . . . . . . . . . . . . . . . . . . . . . . 419 System, Remote Starting . . . . . . . . . . . . . . . . . . . . 29
Steering
Power . . . . . . . . . . . . . . . . . . . . . . . . . . 437,438 Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Tilt Column . . . . . . . . . . . . . . . . . . . . . . . . 209 Telescoping Steering Column . . . . . . . . . . . . . . . 209
Wheel, Heated . . . . . . . . . . . . . . . . . . . . . . 210 Temperature Control, Automatic (ATC) . . . . . . . . 400
Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . 209 Temperature Gauge, Engine Coolant . . . . . . . 296,513
Steering Wheel Audio Controls . . . . . . . . . . . . . . 389 Tether Anchor, Child Restraint . . . . . . . . . . . . . . . 89
Steering Wheel Mounted Sound Tilt Steering Column . . . . . . . . . . . . . . . . . . . . . 209
System Controls . . . . . . . . . . . . . . . . . . . . . . . . . 389 Tire and Loading Information Placard . . . . . . . . . 457
10
632 INDEX
Tire Identification Number (TIN) . . . . . . . . . . . . . 455 Replacement . . . . . . . . . . . . . . . . . . . . . . . . 469
Tire Markings . . . . . . . . . . . . . . . . . . . . . . . . . . 452 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Tire Safety Information . . . . . . . . . . . . . . . . . . . . 452 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . 452,461
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . 103,461,613 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453
Aging (Life of Tires) . . . . . . . . . . . . . . . . . . 468 Snow Tires . . . . . . . . . . . . . . . . . . . . . . . . . 472
Air Pressure . . . . . . . . . . . . . . . . . . . . . . . . 461 Spare Tire . . . . . . . . . . . . . . . . . . . . . . . . . . 515
Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . 470 Spinning . . . . . . . . . . . . . . . . . . . . . . . . . . . 467
Changing . . . . . . . . . . . . . . . . . . . . . . . . . . 513 Tread Wear Indicators . . . . . . . . . . . . . . . . . 468
Compact Spare . . . . . . . . . . . . . . . . . . . . . . 465 Tongue Weight/Trailer Weight . . . . . . . . . . . . . . 502
General Information . . . . . . . . . . . . . . . . . . 461 Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 495
High Speed . . . . . . . . . . . . . . . . . . . . . . . . . 463 24-Hour Towing Assistance . . . . . . . . . . . . . 139
Inflation Pressures . . . . . . . . . . . . . . . . . . . . 462 Disabled Vehicle . . . . . . . . . . . . . . . . . . . . . 538
Jacking . . . . . . . . . . . . . . . . . . . . . . . . . 513,521 Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
Life of Tires . . . . . . . . . . . . . . . . . . . . . . . . 468 Recreational . . . . . . . . . . . . . . . . . . . . . . . . 509
Load Capacity . . . . . . . . . . . . . . . . . . . . 457,458 Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . 501
Pressure Monitor System (TPMS) . . . . . . . . . 473 Towing Assistance . . . . . . . . . . . . . . . . . . . . . . . 139
Pressure Warning Light . . . . . . . . . . . . . . . . 289 Traction Control . . . . . . . . . . . . . . . . . . . . . . . . . 443
Quality Grading . . . . . . . . . . . . . . . . . . . . . 613 Traction Control Switch . . . . . . . . . . . . . . . . . . . 443
Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
INDEX 633
Trailer Towing . . . . . . . . . . . . . . . . . . . . . . . . . . 495 Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . 286
Cooling System Tips . . . . . . . . . . . . . . . . . . 508 Turn Signals . . . . . . . . . . . . . . . . . . . . . . 204,286,584
Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500
Minimum Requirements . . . . . . . . . . . . . . . . 503 UCI Connector . . . . . . . . . . . . . . . . . . . . . . . . . 346
Trailer and Tongue Weight . . . . . . . . . . . . . . 502 Uconnect (Hands-Free Phone) . . . . . . . . . . . . . 125
Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . 506 Umbrella Holder . . . . . . . . . . . . . . . . . . . . . . . . 256
Trailer Towing Guide . . . . . . . . . . . . . . . . . . . . . 501 Uniform Tire Quality Grades . . . . . . . . . . . . . . . . 613
Trailer Weight . . . . . . . . . . . . . . . . . . . . . . . . . . 501 Universal Consumer Interface (UCI) Connector . . . 346
Transaxle Universal Transmitter . . . . . . . . . . . . . . . . . . . . . 231
Selection of Lubricant . . . . . . . . . . . . . . . . . 588 Unleaded Gasoline . . . . . . . . . . . . . . . . . . . . . . . 482
Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . 567 Upholstery Care . . . . . . . . . . . . . . . . . . . . . . . . 572
Automatic . . . . . . . . . . . . . . . . . . . . . . . 422,567
Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . 567,588 Vanity Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Transmitter Battery Service Variance, Compass . . . . . . . . . . . . . . . . . . . . . . . 313
(Remote Keyless Entry) . . . . . . . . . . . . . . . . . . . . 26 Vehicle Certification Label . . . . . . . . . . . . . . . . . 493
Transmitter, Garage Door Opener (HomeLink) . . 231 Vehicle Identification Number (VIN) . . . . . . . . . . . . 6
Transmitter, Remote Keyless Entry (RKE) . . . . . . . . 20 Vehicle Loading . . . . . . . . . . . . . . . . . . . 458,493,495
Transporting Pets . . . . . . . . . . . . . . . . . . . . . . . . 95 Vehicle Modifications/Alterations . . . . . . . . . . . . . . 7
Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . 468 Vehicle Storage . . . . . . . . . . . . . . . . . . . . . . . 412,582
10
634 INDEX
Voice Recognition System (VR) . . . . . . . . . . . . . . 155 Wheel and Wheel Trim Care . . . . . . . . . . . . . . . . 571
Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . . 41,243
Warning Flasher, Hazard . . . . . . . . . . . . . . . . . . 512 Window Fogging . . . . . . . . . . . . . . . . . . . . . . . . 412
Warning Lights Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
(Instrument Cluster Description) . . . . . . . . . . . . . 286 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . 6 Rear Vent . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Warranty Information . . . . . . . . . . . . . . . . . . . . . 610 Windshield Defroster . . . . . . . . . . . . . . . . . . . . . 101
Washer Windshield Washers . . . . . . . . . . . . . . . . . . . 205,558
Adding Fluid . . . . . . . . . . . . . . . . . . . . . . . 558 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . 558
Washing Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 569 Wiper Blade Replacement . . . . . . . . . . . . . . . . . . 558
Water Wipers, Intermittent . . . . . . . . . . . . . . . . . . . . . . 205
Driving Through . . . . . . . . . . . . . . . . . . . . . 435
Wheel and Wheel Trim . . . . . . . . . . . . . . . . . . . . 571 Zone Control (Temperature Control) . . . . . . . . . . 392
INSTALLATION OF RADIO TRANSMITTING
EQUIPMENT
Special design considerations are incorporated into this The antenna cable should be as short as practical and
vehicles electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use
frequency signals. Mobile two-way radios and telephone only fully shielded coaxial cable.
equipment must be installed properly by trained personnel.
Carefully match the antenna and cable to the radio to
The following must be observed during installation.
ensure a low Standing Wave Ratio (SWR).
The positive power connection should be made directly to
Mobile radio equipment with output power greater than
the battery and fused as close to the battery as possible.
normal may require special precautions.
The negative power connection should be made to body
sheet metal adjacent to the negative battery connection. All installations should be checked for possible interfer-
This connection should not be fused. ence between the communications equipment and the
vehicles electronic systems.
Antennas for two-way radios should be mounted on the roof
or the rear area of the vehicle. Care should be used in
mounting antennas with magnet bases. Magnets may affect
the accuracy or operation of the compass on vehicles so
equipped.
Chrysler Group LLC
12Y532-126-AC 3rd Edition Printed in U.S.A.

2012 Grand - Caravan OM 3rd PDF

Uploaded by

Copyright:

Available Formats

2012 Grand - Caravan OM 3rd PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2012 Grand - Caravan OM 3rd PDF

Uploaded by

Copyright:

Available Formats

2012 Grand Caravan

2012 Grand Caravan

903656_Grand Caravan_OM cover.indd 1 3/15/11 10:41 AM

VEHICLE IDENTIFICATION NUMBER

Stamped VIN Location

A Word About Your Keys . . . . . . . . . . . . . . . . . 12 Remote Starting System If Equipped . . . . . . . 29

Key Fob With Seven-Button RKE Transmitter

Emergency Key Removal Inserting Emergency Key Into Slot

Sliding Door Lock

Drivers Power Window Switches

Front Passenger Power Door Switches

SLIDING SIDE DOOR

Power Sliding Door Switch

LIFTGATE Liftgate Handle Location

Overhead Console Master Power Switch

WARNING! WARNING! (Continued)

Lap/Shoulder Belt Operating Instructions

NOTE: For more information on properly adjusting and

1 Downward Movement 3 Final Downward Movement To Engage Locking Mechanism

LATCH Anchorages (Second Row Anchorages Shown)

Installing The Child Restraint Using The Vehicle

COMMERCIAL CARGO VEHICLES (NO FACTORY

Commercial Child Restraint Tether Anchor

ENGINE BREAK-IN RECOMMENDATIONS CAUTION!

WARNING! WARNING! (Continued)

Manual Rearview Mirror

Automatic Dimming Mirror

Drivers Automatic Dimming Mirror If Equipped

Sensor Locations BSM Warning Light

Rear Cross Path

Voice Commands Voice Commands

Voice Commands Voice Commands

Manual Recline Lever

Active Head Restraint (Normal Position)

Head Restraints Second Row Quad Seats

Seatback Recliner Lever, Seat Tumble,

Automatic Folding Seatback Tumbled Second Row Seat

Raising The Head Restraint

Seatback Recliner Lever, Seat Tumble,

Quad Seats If Equipped

Fold-Flat Quad Seat

Pull Strap for Third Row Passengers

B-Pillar Grab Handle

Second Row Bench Seat

Cross Beam for Seat Removal

Third Row Power Seat Switch

Head Restraint Release Strap 1

One Touch Folding Seat Third Row

Stowed Third Row Seat

TO OPEN AND CLOSE THE HOOD

Safety Lever Location Hood Prop Rod

Headlight Switch With Halo Control

Park Assist System ON

Park Assist System OFF Slow Tone

Fast Tone Continuous Tone

WARNING! CAUTION! (Continued)

CAUTION! Turning ParkView On Or Off With

Full Open Position Conversation Mirror Position

GARAGE DOOR OPENER IF EQUIPPED