|
HTML rendering created 2023-12-22 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|
NFS(5) File Formats Manual NFS(5)
nfs - fstab format and options for the nfs file systems
/etc/fstab
NFS is an Internet Standard protocol created by Sun Microsystems
in 1984. NFS was developed to allow file sharing between systems
residing on a local area network. Depending on kernel
configuration, the Linux NFS client may support NFS versions 3,
4.0, 4.1, or 4.2.
The mount(8) command attaches a file system to the system's name
space hierarchy at a given mount point. The /etc/fstab file
describes how mount(8) should assemble a system's file name
hierarchy from various independent file systems (including file
systems exported by NFS servers). Each line in the /etc/fstab
file describes a single file system, its mount point, and a set
of default mount options for that mount point.
For NFS file system mounts, a line in the /etc/fstab file
specifies the server name, the path name of the exported server
directory to mount, the local directory that is the mount point,
the type of file system that is being mounted, and a list of
mount options that control the way the filesystem is mounted and
how the NFS client behaves when accessing files on this mount
point. The fifth and sixth fields on each line are not used by
NFS, thus conventionally each contain the digit zero. For
example:
server:path /mountpoint fstype option,option,... 0 0
The server's hostname and export pathname are separated by a
colon, while the mount options are separated by commas. The
remaining fields are separated by blanks or tabs.
The server's hostname can be an unqualified hostname, a fully
qualified domain name, a dotted quad IPv4 address, or an IPv6
address enclosed in square brackets. Link-local and site-local
IPv6 addresses must be accompanied by an interface identifier.
See ipv6(7) for details on specifying raw IPv6 addresses.
The fstype field contains "nfs". Use of the "nfs4" fstype in
/etc/fstab is deprecated.
Refer to mount(8) for a description of generic mount options
available for all file systems. If you do not need to specify any
mount options, use the generic option defaults in /etc/fstab.
Options supported by all versions
These options are valid to use with any NFS version.
nfsvers=n
The NFS protocol version number used to contact the
server's NFS service. If the server does not support the
requested version, the mount request fails. If this
option is not specified, the client tries version 4.2
first, then negotiates down until it finds a version
supported by the server.
vers=n This option is an alternative to the nfsvers option. It
is included for compatibility with other operating systems
soft / softerr / hard
Determines the recovery behavior of the NFS client after
an NFS request times out. If no option is specified (or
if the hard option is specified), NFS requests are retried
indefinitely. If either the soft or softerr option is
specified, then the NFS client fails an NFS request after
retrans retransmissions have been sent, causing the NFS
client to return either the error EIO (for the soft
option) or ETIMEDOUT (for the softerr option) to the
calling application.
NB: A so-called "soft" timeout can cause silent data
corruption in certain cases. As such, use the soft or
softerr option only when client responsiveness is more
important than data integrity. Using NFS over TCP or
increasing the value of the retrans option may mitigate
some of the risks of using the soft or softerr option.
softreval / nosoftreval
In cases where the NFS server is down, it may be useful to
allow the NFS client to continue to serve up paths and
attributes from cache after retrans attempts to revalidate
that cache have timed out. This may, for instance, be
helpful when trying to unmount a filesystem tree from a
server that is permanently down.
It is possible to combine softreval with the soft mount
option, in which case operations that cannot be served up
from cache will time out and return an error after retrans
attempts. The combination with the default hard mount
option implies those uncached operations will continue to
retry until a response is received from the server.
Note: the default mount option is nosoftreval which
disallows fallback to cache when revalidation fails, and
instead follows the behavior dictated by the hard or soft
mount option.
intr / nointr
This option is provided for backward compatibility. It is
ignored after kernel 2.6.25.
timeo=n
The time in deciseconds (tenths of a second) the NFS
client waits for a response before it retries an NFS
request.
For NFS over TCP the default timeo value is 600 (60
seconds). The NFS client performs linear backoff: After
each retransmission the timeout is increased by timeo up
to the maximum of 600 seconds.
However, for NFS over UDP, the client uses an adaptive
algorithm to estimate an appropriate timeout value for
frequently used request types (such as READ and WRITE
requests), but uses the timeo setting for infrequently
used request types (such as FSINFO requests). If the
timeo option is not specified, infrequently used request
types are retried after 1.1 seconds. After each
retransmission, the NFS client doubles the timeout for
that request, up to a maximum timeout length of 60
seconds.
retrans=n
The number of times the NFS client retries a request
before it attempts further recovery action. If the retrans
option is not specified, the NFS client tries each UDP
request three times and each TCP request twice.
The NFS client generates a "server not responding" message
after retrans retries, then attempts further recovery
(depending on whether the hard mount option is in effect).
rsize=n
The maximum number of bytes in each network READ request
that the NFS client can receive when reading data from a
file on an NFS server. The actual data payload size of
each NFS READ request is equal to or smaller than the
rsize setting. The largest read payload supported by the
Linux NFS client is 1,048,576 bytes (one megabyte).
The rsize value is a positive integral multiple of 1024.
Specified rsize values lower than 1024 are replaced with
4096; values larger than 1048576 are replaced with
1048576. If a specified value is within the supported
range but not a multiple of 1024, it is rounded down to
the nearest multiple of 1024.
If an rsize value is not specified, or if the specified
rsize value is larger than the maximum that either client
or server can support, the client and server negotiate the
largest rsize value that they can both support.
The rsize mount option as specified on the mount(8)
command line appears in the /etc/mtab file. However, the
effective rsize value negotiated by the client and server
is reported in the /proc/mounts file.
wsize=n
The maximum number of bytes per network WRITE request that
the NFS client can send when writing data to a file on an
NFS server. The actual data payload size of each NFS WRITE
request is equal to or smaller than the wsize setting. The
largest write payload supported by the Linux NFS client is
1,048,576 bytes (one megabyte).
Similar to rsize , the wsize value is a positive integral
multiple of 1024. Specified wsize values lower than 1024
are replaced with 4096; values larger than 1048576 are
replaced with 1048576. If a specified value is within the
supported range but not a multiple of 1024, it is rounded
down to the nearest multiple of 1024.
If a wsize value is not specified, or if the specified
wsize value is larger than the maximum that either client
or server can support, the client and server negotiate the
largest wsize value that they can both support.
The wsize mount option as specified on the mount(8)
command line appears in the /etc/mtab file. However, the
effective wsize value negotiated by the client and server
is reported in the /proc/mounts file.
ac / noac
Selects whether the client may cache file attributes. If
neither option is specified (or if ac is specified), the
client caches file attributes.
To improve performance, NFS clients cache file attributes.
Every few seconds, an NFS client checks the server's
version of each file's attributes for updates. Changes
that occur on the server in those small intervals remain
undetected until the client checks the server again. The
noac option prevents clients from caching file attributes
so that applications can more quickly detect file changes
on the server.
In addition to preventing the client from caching file
attributes, the noac option forces application writes to
become synchronous so that local changes to a file become
visible on the server immediately. That way, other
clients can quickly detect recent writes when they check
the file's attributes.
Using the noac option provides greater cache coherence
among NFS clients accessing the same files, but it
extracts a significant performance penalty. As such,
judicious use of file locking is encouraged instead. The
DATA AND METADATA COHERENCE section contains a detailed
discussion of these trade-offs.
acregmin=n
The minimum time (in seconds) that the NFS client caches
attributes of a regular file before it requests fresh
attribute information from a server. If this option is
not specified, the NFS client uses a 3-second minimum.
See the DATA AND METADATA COHERENCE section for a full
discussion of attribute caching.
acregmax=n
The maximum time (in seconds) that the NFS client caches
attributes of a regular file before it requests fresh
attribute information from a server. If this option is
not specified, the NFS client uses a 60-second maximum.
See the DATA AND METADATA COHERENCE section for a full
discussion of attribute caching.
acdirmin=n
The minimum time (in seconds) that the NFS client caches
attributes of a directory before it requests fresh
attribute information from a server. If this option is
not specified, the NFS client uses a 30-second minimum.
See the DATA AND METADATA COHERENCE section for a full
discussion of attribute caching.
acdirmax=n
The maximum time (in seconds) that the NFS client caches
attributes of a directory before it requests fresh
attribute information from a server. If this option is
not specified, the NFS client uses a 60-second maximum.
See the DATA AND METADATA COHERENCE section for a full
discussion of attribute caching.
actimeo=n
Using actimeo sets all of acregmin, acregmax, acdirmin,
and acdirmax to the same value. If this option is not
specified, the NFS client uses the defaults for each of
these options listed above.
bg / fg
Determines how the mount(8) command behaves if an attempt
to mount an export fails. The fg option causes mount(8)
to exit with an error status if any part of the mount
request times out or fails outright. This is called a
"foreground" mount, and is the default behavior if neither
the fg nor bg mount option is specified.
If the bg option is specified, a timeout or failure causes
the mount(8) command to fork a child which continues to
attempt to mount the export. The parent immediately
returns with a zero exit code. This is known as a
"background" mount.
If the local mount point directory is missing, the
mount(8) command acts as if the mount request timed out.
This permits nested NFS mounts specified in /etc/fstab to
proceed in any order during system initialization, even if
some NFS servers are not yet available. Alternatively
these issues can be addressed using an automounter (refer
to automount(8) for details).
nconnect=n
When using a connection oriented protocol such as TCP, it
may sometimes be advantageous to set up multiple
connections between the client and server. For instance,
if your clients and/or servers are equipped with multiple
network interface cards (NICs), using multiple connections
to spread the load may improve overall performance. In
such cases, the nconnect option allows the user to specify
the number of connections that should be established
between the client and server up to a limit of 16.
Note that the nconnect option may also be used by some
pNFS drivers to decide how many connections to set up to
the data servers.
rdirplus / nordirplus
Selects whether to use NFS v3 or v4 READDIRPLUS requests.
If this option is not specified, the NFS client uses
READDIRPLUS requests on NFS v3 or v4 mounts to read small
directories. Some applications perform better if the
client uses only READDIR requests for all directories.
retry=n
The number of minutes that the mount(8) command retries an
NFS mount operation in the foreground or background before
giving up. If this option is not specified, the default
value for foreground mounts is 2 minutes, and the default
value for background mounts is 10000 minutes (80 minutes
shy of one week). If a value of zero is specified, the
mount(8) command exits immediately after the first
failure.
Note that this only affects how many retries are made and
doesn't affect the delay caused by each retry. For UDP
each retry takes the time determined by the timeo and
retrans options, which by default will be about 7 seconds.
For TCP the default is 3 minutes, but system TCP
connection timeouts will sometimes limit the timeout of
each retransmission to around 2 minutes.
sec=flavors
A colon-separated list of one or more security flavors to
use for accessing files on the mounted export. If the
server does not support any of these flavors, the mount
operation fails. If sec= is not specified, the client
attempts to find a security flavor that both the client
and the server supports. Valid flavors are none, sys,
krb5, krb5i, and krb5p. Refer to the SECURITY
CONSIDERATIONS section for details.
sharecache / nosharecache
Determines how the client's data cache and attribute cache
are shared when mounting the same export more than once
concurrently. Using the same cache reduces memory
requirements on the client and presents identical file
contents to applications when the same remote file is
accessed via different mount points.
If neither option is specified, or if the sharecache
option is specified, then a single cache is used for all
mount points that access the same export. If the
nosharecache option is specified, then that mount point
gets a unique cache. Note that when data and attribute
caches are shared, the mount options from the first mount
point take effect for subsequent concurrent mounts of the
same export.
As of kernel 2.6.18, the behavior specified by
nosharecache is legacy caching behavior. This is
considered a data risk since multiple cached copies of the
same file on the same client can become out of sync
following a local update of one of the copies.
resvport / noresvport
Specifies whether the NFS client should use a privileged
source port when communicating with an NFS server for this
mount point. If this option is not specified, or the
resvport option is specified, the NFS client uses a
privileged source port. If the noresvport option is
specified, the NFS client uses a non-privileged source
port. This option is supported in kernels 2.6.28 and
later.
Using non-privileged source ports helps increase the
maximum number of NFS mount points allowed on a client,
but NFS servers must be configured to allow clients to
connect via non-privileged source ports.
Refer to the SECURITY CONSIDERATIONS section for important
details.
lookupcache=mode
Specifies how the kernel manages its cache of directory
entries for a given mount point. mode can be one of all,
none, pos, or positive. This option is supported in
kernels 2.6.28 and later.
The Linux NFS client caches the result of all NFS LOOKUP
requests. If the requested directory entry exists on the
server, the result is referred to as positive. If the
requested directory entry does not exist on the server,
the result is referred to as negative.
If this option is not specified, or if all is specified,
the client assumes both types of directory cache entries
are valid until their parent directory's cached attributes
expire.
If pos or positive is specified, the client assumes
positive entries are valid until their parent directory's
cached attributes expire, but always revalidates negative
entires before an application can use them.
If none is specified, the client revalidates both types of
directory cache entries before an application can use
them. This permits quick detection of files that were
created or removed by other clients, but can impact
application and server performance.
The DATA AND METADATA COHERENCE section contains a
detailed discussion of these trade-offs.
fsc / nofsc
Enable/Disables the cache of (read-only) data pages to the
local disk using the FS-Cache facility. See cachefilesd(8)
and <kernel_source>/Documentation/filesystems/caching for
detail on how to configure the FS-Cache facility. Default
value is nofsc.
sloppy The sloppy option is an alternative to specifying
mount.nfs -s option.
xprtsec=policy
Specifies the use of transport layer security to protect
NFS network traffic on behalf of this mount point. policy
can be one of none, tls, or mtls.
If none is specified, transport layer security is forced
off, even if the NFS server supports transport layer
security.
If tls is specified, the client uses RPC-with-TLS to
provide in-transit confidentiality.
If mtls is specified, the client uses RPC-with-TLS to
authenticate itself and to provide in-transit
confidentiality.
If either tls or mtls is specified and the server does not
support RPC-with-TLS or peer authentication fails, the
mount attempt fails.
If the xprtsec= option is not specified, the default
behavior depends on the kernel version, but is usually
equivalent to xprtsec=none.
Options for NFS versions 2 and 3 only
Use these options, along with the options in the above
subsection, for NFS versions 2 and 3 only.
proto=netid
The netid determines the transport that is used to
communicate with the NFS server. Available options are
udp, udp6, tcp, tcp6, rdma, and rdma6. Those which end in
6 use IPv6 addresses and are only available if support for
TI-RPC is built in. Others use IPv4 addresses.
Each transport protocol uses different default retrans and
timeo settings. Refer to the description of these two
mount options for details.
In addition to controlling how the NFS client transmits
requests to the server, this mount option also controls
how the mount(8) command communicates with the server's
rpcbind and mountd services. Specifying a netid that uses
TCP forces all traffic from the mount(8) command and the
NFS client to use TCP. Specifying a netid that uses UDP
forces all traffic types to use UDP.
Before using NFS over UDP, refer to the TRANSPORT METHODS
section.
If the proto mount option is not specified, the mount(8)
command discovers which protocols the server supports and
chooses an appropriate transport for each service. Refer
to the TRANSPORT METHODS section for more details.
udp The udp option is an alternative to specifying proto=udp.
It is included for compatibility with other operating
systems.
Before using NFS over UDP, refer to the TRANSPORT METHODS
section.
tcp The tcp option is an alternative to specifying proto=tcp.
It is included for compatibility with other operating
systems.
rdma The rdma option is an alternative to specifying
proto=rdma.
port=n The numeric value of the server's NFS service port. If
the server's NFS service is not available on the specified
port, the mount request fails.
If this option is not specified, or if the specified port
value is 0, then the NFS client uses the NFS service port
number advertised by the server's rpcbind service. The
mount request fails if the server's rpcbind service is not
available, the server's NFS service is not registered with
its rpcbind service, or the server's NFS service is not
available on the advertised port.
mountport=n
The numeric value of the server's mountd port. If the
server's mountd service is not available on the specified
port, the mount request fails.
If this option is not specified, or if the specified port
value is 0, then the mount(8) command uses the mountd
service port number advertised by the server's rpcbind
service. The mount request fails if the server's rpcbind
service is not available, the server's mountd service is
not registered with its rpcbind service, or the server's
mountd service is not available on the advertised port.
This option can be used when mounting an NFS server
through a firewall that blocks the rpcbind protocol.
mountproto=netid
The transport the NFS client uses to transmit requests to
the NFS server's mountd service when performing this mount
request, and when later unmounting this mount point.
netid may be one of udp, and tcp which use IPv4 address
or, if TI-RPC is built into the mount.nfs command, udp6,
and tcp6 which use IPv6 addresses.
This option can be used when mounting an NFS server
through a firewall that blocks a particular transport.
When used in combination with the proto option, different
transports for mountd requests and NFS requests can be
specified. If the server's mountd service is not
available via the specified transport, the mount request
fails.
Refer to the TRANSPORT METHODS section for more on how the
mountproto mount option interacts with the proto mount
option.
mounthost=name
The hostname of the host running mountd. If this option
is not specified, the mount(8) command assumes that the
mountd service runs on the same host as the NFS service.
mountvers=n
The RPC version number used to contact the server's
mountd. If this option is not specified, the client uses
a version number appropriate to the requested NFS version.
This option is useful when multiple NFS services are
running on the same remote server host.
namlen=n
The maximum length of a pathname component on this mount.
If this option is not specified, the maximum length is
negotiated with the server. In most cases, this maximum
length is 255 characters.
Some early versions of NFS did not support this
negotiation. Using this option ensures that pathconf(3)
reports the proper maximum component length to
applications in such cases.
lock / nolock
Selects whether to use the NLM sideband protocol to lock
files on the server. If neither option is specified (or
if lock is specified), NLM locking is used for this mount
point. When using the nolock option, applications can
lock files, but such locks provide exclusion only against
other applications running on the same client. Remote
applications are not affected by these locks.
NLM locking must be disabled with the nolock option when
using NFS to mount /var because /var contains files used
by the NLM implementation on Linux. Using the nolock
option is also required when mounting exports on NFS
servers that do not support the NLM protocol.
cto / nocto
Selects whether to use close-to-open cache coherence
semantics. If neither option is specified (or if cto is
specified), the client uses close-to-open cache coherence
semantics. If the nocto option is specified, the client
uses a non-standard heuristic to determine when files on
the server have changed.
Using the nocto option may improve performance for read-
only mounts, but should be used only if the data on the
server changes only occasionally. The DATA AND METADATA
COHERENCE section discusses the behavior of this option in
more detail.
acl / noacl
Selects whether to use the NFSACL sideband protocol on
this mount point. The NFSACL sideband protocol is a
proprietary protocol implemented in Solaris that manages
Access Control Lists. NFSACL was never made a standard
part of the NFS protocol specification.
If neither acl nor noacl option is specified, the NFS
client negotiates with the server to see if the NFSACL
protocol is supported, and uses it if the server supports
it. Disabling the NFSACL sideband protocol may be
necessary if the negotiation causes problems on the client
or server. Refer to the SECURITY CONSIDERATIONS section
for more details.
local_lock=mechanism
Specifies whether to use local locking for any or both of
the flock and the POSIX locking mechanisms. mechanism can
be one of all, flock, posix, or none. This option is
supported in kernels 2.6.37 and later.
The Linux NFS client provides a way to make locks local.
This means, the applications can lock files, but such
locks provide exclusion only against other applications
running on the same client. Remote applications are not
affected by these locks.
If this option is not specified, or if none is specified,
the client assumes that the locks are not local.
If all is specified, the client assumes that both flock
and POSIX locks are local.
If flock is specified, the client assumes that only flock
locks are local and uses NLM sideband protocol to lock
files when POSIX locks are used.
If posix is specified, the client assumes that POSIX locks
are local and uses NLM sideband protocol to lock files
when flock locks are used.
To support legacy flock behavior similar to that of NFS
clients < 2.6.12, use 'local_lock=flock'. This option is
required when exporting NFS mounts via Samba as Samba maps
Windows share mode locks as flock. Since NFS clients >
2.6.12 implement flock by emulating POSIX locks, this will
result in conflicting locks.
NOTE: When used together, the 'local_lock' mount option
will be overridden by 'nolock'/'lock' mount option.
Options for NFS version 4 only
Use these options, along with the options in the first subsection
above, for NFS version 4.0 and newer.
proto=netid
The netid determines the transport that is used to
communicate with the NFS server. Supported options are
tcp, tcp6, rdma, and rdma6. tcp6 use IPv6 addresses and
is only available if support for TI-RPC is built in. Both
others use IPv4 addresses.
All NFS version 4 servers are required to support TCP, so
if this mount option is not specified, the NFS version 4
client uses the TCP protocol. Refer to the TRANSPORT
METHODS section for more details.
minorversion=n
Specifies the protocol minor version number. NFSv4
introduces "minor versioning," where NFS protocol
enhancements can be introduced without bumping the NFS
protocol version number. Before kernel 2.6.38, the minor
version is always zero, and this option is not recognized.
After this kernel, specifying "minorversion=1" enables a
number of advanced features, such as NFSv4 sessions.
Recent kernels allow the minor version to be specified
using the vers= option. For example, specifying vers=4.1
is the same as specifying vers=4,minorversion=1.
port=n The numeric value of the server's NFS service port. If
the server's NFS service is not available on the specified
port, the mount request fails.
If this mount option is not specified, the NFS client uses
the standard NFS port number of 2049 without first
checking the server's rpcbind service. This allows an NFS
version 4 client to contact an NFS version 4 server
through a firewall that may block rpcbind requests.
If the specified port value is 0, then the NFS client uses
the NFS service port number advertised by the server's
rpcbind service. The mount request fails if the server's
rpcbind service is not available, the server's NFS service
is not registered with its rpcbind service, or the
server's NFS service is not available on the advertised
port.
cto / nocto
Selects whether to use close-to-open cache coherence
semantics for NFS directories on this mount point. If
neither cto nor nocto is specified, the default is to use
close-to-open cache coherence semantics for directories.
File data caching behavior is not affected by this option.
The DATA AND METADATA COHERENCE section discusses the
behavior of this option in more detail.
clientaddr=n.n.n.n
clientaddr=n:n:...:n
Specifies a single IPv4 address (in dotted-quad form), or
a non-link-local IPv6 address, that the NFS client
advertises to allow servers to perform NFS version 4.0
callback requests against files on this mount point. If
the server is unable to establish callback connections to
clients, performance may degrade, or accesses to files may
temporarily hang. Can specify a value of IPv4_ANY
(0.0.0.0) or equivalent IPv6 any address which will signal
to the NFS server that this NFS client does not want
delegations.
If this option is not specified, the mount(8) command
attempts to discover an appropriate callback address
automatically. The automatic discovery process is not
perfect, however. In the presence of multiple client
network interfaces, special routing policies, or atypical
network topologies, the exact address to use for callbacks
may be nontrivial to determine.
NFS protocol versions 4.1 and 4.2 use the client-
established TCP connection for callback requests, so do
not require the server to connect to the client. This
option is therefore only affect NFS version 4.0 mounts.
migration / nomigration
Selects whether the client uses an identification string
that is compatible with NFSv4 Transparent State Migration
(TSM). If the mounted server supports NFSv4 migration
with TSM, specify the migration option.
Some server features misbehave in the face of a migration-
compatible identification string. The nomigration option
retains the use of a traditional client indentification
string which is compatible with legacy NFS servers. This
is also the behavior if neither option is specified. A
client's open and lock state cannot be migrated
transparently when it identifies itself via a traditional
identification string.
This mount option has no effect with NFSv4 minor versions
newer than zero, which always use TSM-compatible client
identification strings.
max_connect=n
While nconnect option sets a limit on the number of
connections that can be established to a given server IP,
max_connect option allows the user to specify maximum
number of connections to different server IPs that belong
to the same NFSv4.1+ server (session trunkable
connections) up to a limit of 16. When client discovers
that it established a client ID to an already existing
server, instead of dropping the newly created network
transport, the client will add this new connection to the
list of available transports for that RPC client.
trunkdiscovery / notrunkdiscovery
When the client discovers a new filesystem on a NFSv4.1+
server, the trunkdiscovery mount option will cause it to
send a GETATTR for the fs_locations attribute. If is
receives a non-zero length reply, it will iterate through
the response, and for each server location it will
establish a connection, send an EXCHANGE_ID, and test for
session trunking. If the trunking test succeeds, the
connection will be added to the existing set of transports
for the server, subject to the limit specified by the
max_connect option. The default is notrunkdiscovery.
The nfs4 file system type is an old syntax for specifying NFSv4
usage. It can still be used with all NFSv4-specific and common
options, excepted the nfsvers mount option.
If the mount command is configured to do so, all of the mount
options described in the previous section can also be configured
in the /etc/nfsmount.conf file. See nfsmount.conf(5) for details.
To mount using NFS version 3, use the nfs file system type and
specify the nfsvers=3 mount option. To mount using NFS version
4, use either the nfs file system type, with the nfsvers=4 mount
option, or the nfs4 file system type.
The following example from an /etc/fstab file causes the mount
command to negotiate reasonable defaults for NFS behavior.
server:/export /mnt nfs defaults 0 0
This example shows how to mount using NFS version 4 over TCP with
Kerberos 5 mutual authentication.
server:/export /mnt nfs4 sec=krb5 0 0
This example shows how to mount using NFS version 4 over TCP with
Kerberos 5 privacy or data integrity mode.
server:/export /mnt nfs4 sec=krb5p:krb5i 0 0
This example can be used to mount /usr over NFS.
server:/export /usr nfs ro,nolock,nocto,actimeo=3600 0 0
This example shows how to mount an NFS server using a raw IPv6
link-local address.
[fe80::215:c5ff:fb3e:e2b1%eth0]:/export /mnt nfs defaults 0 0
NFS clients send requests to NFS servers via Remote Procedure
Calls, or RPCs. The RPC client discovers remote service
endpoints automatically, handles per-request authentication,
adjusts request parameters for different byte endianness on
client and server, and retransmits requests that may have been
lost by the network or server. RPC requests and replies flow
over a network transport.
In most cases, the mount(8) command, NFS client, and NFS server
can automatically negotiate proper transport and data transfer
size settings for a mount point. In some cases, however, it pays
to specify these settings explicitly using mount options.
Traditionally, NFS clients used the UDP transport exclusively for
transmitting requests to servers. Though its implementation is
simple, NFS over UDP has many limitations that prevent smooth
operation and good performance in some common deployment
environments. Even an insignificant packet loss rate results in
the loss of whole NFS requests; as such, retransmit timeouts are
usually in the subsecond range to allow clients to recover
quickly from dropped requests, but this can result in extraneous
network traffic and server load.
However, UDP can be quite effective in specialized settings where
the networks MTU is large relative to NFSs data transfer size
(such as network environments that enable jumbo Ethernet frames).
In such environments, trimming the rsize and wsize settings so
that each NFS read or write request fits in just a few network
frames (or even in a single frame) is advised. This reduces
the probability that the loss of a single MTU-sized network frame
results in the loss of an entire large read or write request.
TCP is the default transport protocol used for all modern NFS
implementations. It performs well in almost every conceivable
network environment and provides excellent guarantees against
data corruption caused by network unreliability. TCP is often a
requirement for mounting a server through a network firewall.
Under normal circumstances, networks drop packets much more
frequently than NFS servers drop requests. As such, an
aggressive retransmit timeout setting for NFS over TCP is
unnecessary. Typical timeout settings for NFS over TCP are
between one and ten minutes. After the client exhausts its
retransmits (the value of the retrans mount option), it assumes a
network partition has occurred, and attempts to reconnect to the
server on a fresh socket. Since TCP itself makes network data
transfer reliable, rsize and wsize can safely be allowed to
default to the largest values supported by both client and
server, independent of the network's MTU size.
Using the mountproto mount option
This section applies only to NFS version 3 mounts since NFS
version 4 does not use a separate protocol for mount requests.
The Linux NFS client can use a different transport for contacting
an NFS server's rpcbind service, its mountd service, its Network
Lock Manager (NLM) service, and its NFS service. The exact
transports employed by the Linux NFS client for each mount point
depends on the settings of the transport mount options, which
include proto, mountproto, udp, and tcp.
The client sends Network Status Manager (NSM) notifications via
UDP no matter what transport options are specified, but listens
for server NSM notifications on both UDP and TCP. The NFS Access
Control List (NFSACL) protocol shares the same transport as the
main NFS service.
If no transport options are specified, the Linux NFS client uses
UDP to contact the server's mountd service, and TCP to contact
its NLM and NFS services by default.
If the server does not support these transports for these
services, the mount(8) command attempts to discover what the
server supports, and then retries the mount request once using
the discovered transports. If the server does not advertise any
transport supported by the client or is misconfigured, the mount
request fails. If the bg option is in effect, the mount command
backgrounds itself and continues to attempt the specified mount
request.
When the proto option, the udp option, or the tcp option is
specified but the mountproto option is not, the specified
transport is used to contact both the server's mountd service and
for the NLM and NFS services.
If the mountproto option is specified but none of the proto, udp
or tcp options are specified, then the specified transport is
used for the initial mountd request, but the mount command
attempts to discover what the server supports for the NFS
protocol, preferring TCP if both transports are supported.
If both the mountproto and proto (or udp or tcp) options are
specified, then the transport specified by the mountproto option
is used for the initial mountd request, and the transport
specified by the proto option (or the udp or tcp options) is used
for NFS, no matter what order these options appear. No automatic
service discovery is performed if these options are specified.
If any of the proto, udp, tcp, or mountproto options are
specified more than once on the same mount command line, then the
value of the rightmost instance of each of these options takes
effect.
Using NFS over UDP on high-speed links
Using NFS over UDP on high-speed links such as Gigabit can cause
silent data corruption.
The problem can be triggered at high loads, and is caused by
problems in IP fragment reassembly. NFS read and writes typically
transmit UDP packets of 4 Kilobytes or more, which have to be
broken up into several fragments in order to be sent over the
Ethernet link, which limits packets to 1500 bytes by default.
This process happens at the IP network layer and is called
fragmentation.
In order to identify fragments that belong together, IP assigns a
16bit IP ID value to each packet; fragments generated from the
same UDP packet will have the same IP ID. The receiving system
will collect these fragments and combine them to form the
original UDP packet. This process is called reassembly. The
default timeout for packet reassembly is 30 seconds; if the
network stack does not receive all fragments of a given packet
within this interval, it assumes the missing fragment(s) got lost
and discards those it already received.
The problem this creates over high-speed links is that it is
possible to send more than 65536 packets within 30 seconds. In
fact, with heavy NFS traffic one can observe that the IP IDs
repeat after about 5 seconds.
This has serious effects on reassembly: if one fragment gets
lost, another fragment from a different packet but with the same
IP ID will arrive within the 30 second timeout, and the network
stack will combine these fragments to form a new packet. Most of
the time, network layers above IP will detect this mismatched
reassembly - in the case of UDP, the UDP checksum, which is a 16
bit checksum over the entire packet payload, will usually not
match, and UDP will discard the bad packet.
However, the UDP checksum is 16 bit only, so there is a chance of
1 in 65536 that it will match even if the packet payload is
completely random (which very often isn't the case). If that is
the case, silent data corruption will occur.
This potential should be taken seriously, at least on Gigabit
Ethernet. Network speeds of 100Mbit/s should be considered less
problematic, because with most traffic patterns IP ID wrap around
will take much longer than 30 seconds.
It is therefore strongly recommended to use NFS over TCP where
possible, since TCP does not perform fragmentation.
If you absolutely have to use NFS over UDP over Gigabit Ethernet,
some steps can be taken to mitigate the problem and reduce the
probability of corruption:
Jumbo frames: Many Gigabit network cards are capable of
transmitting frames bigger than the 1500 byte
limit of traditional Ethernet, typically 9000
bytes. Using jumbo frames of 9000 bytes will allow
you to run NFS over UDP at a page size of 8K
without fragmentation. Of course, this is only
feasible if all involved stations support jumbo
frames.
To enable a machine to send jumbo frames on cards
that support it, it is sufficient to configure the
interface for a MTU value of 9000.
Lower reassembly timeout:
By lowering this timeout below the time it takes
the IP ID counter to wrap around, incorrect
reassembly of fragments can be prevented as well.
To do so, simply write the new timeout value (in
seconds) to the file
/proc/sys/net/ipv4/ipfrag_time.
A value of 2 seconds will greatly reduce the
probability of IPID clashes on a single Gigabit
link, while still allowing for a reasonable
timeout when receiving fragmented traffic from
distant peers.
Some modern cluster file systems provide perfect cache coherence
among their clients. Perfect cache coherence among disparate NFS
clients is expensive to achieve, especially on wide area
networks. As such, NFS settles for weaker cache coherence that
satisfies the requirements of most file sharing types.
Close-to-open cache consistency
Typically file sharing is completely sequential. First client A
opens a file, writes something to it, then closes it. Then
client B opens the same file, and reads the changes.
When an application opens a file stored on an NFS version 3
server, the NFS client checks that the file exists on the server
and is permitted to the opener by sending a GETATTR or ACCESS
request. The NFS client sends these requests regardless of the
freshness of the file's cached attributes.
When the application closes the file, the NFS client writes back
any pending changes to the file so that the next opener can view
the changes. This also gives the NFS client an opportunity to
report write errors to the application via the return code from
close(2).
The behavior of checking at open time and flushing at close time
is referred to as close-to-open cache consistency, or CTO. It
can be disabled for an entire mount point using the nocto mount
option.
Weak cache consistency
There are still opportunities for a client's data cache to
contain stale data. The NFS version 3 protocol introduced "weak
cache consistency" (also known as WCC) which provides a way of
efficiently checking a file's attributes before and after a
single request. This allows a client to help identify changes
that could have been made by other clients.
When a client is using many concurrent operations that update the
same file at the same time (for example, during asynchronous
write behind), it is still difficult to tell whether it was that
client's updates or some other client's updates that altered the
file.
Attribute caching
Use the noac mount option to achieve attribute cache coherence
among multiple clients. Almost every file system operation
checks file attribute information. The client keeps this
information cached for a period of time to reduce network and
server load. When noac is in effect, a client's file attribute
cache is disabled, so each operation that needs to check a file's
attributes is forced to go back to the server. This permits a
client to see changes to a file very quickly, at the cost of many
extra network operations.
Be careful not to confuse the noac option with "no data caching."
The noac mount option prevents the client from caching file
metadata, but there are still races that may result in data cache
incoherence between client and server.
The NFS protocol is not designed to support true cluster file
system cache coherence without some type of application
serialization. If absolute cache coherence among clients is
required, applications should use file locking. Alternatively,
applications can also open their files with the O_DIRECT flag to
disable data caching entirely.
File timestamp maintenance
NFS servers are responsible for managing file and directory
timestamps (atime, ctime, and mtime). When a file is accessed or
updated on an NFS server, the file's timestamps are updated just
like they would be on a filesystem local to an application.
NFS clients cache file attributes, including timestamps. A
file's timestamps are updated on NFS clients when its attributes
are retrieved from the NFS server. Thus there may be some delay
before timestamp updates on an NFS server appear to applications
on NFS clients.
To comply with the POSIX filesystem standard, the Linux NFS
client relies on NFS servers to keep a file's mtime and ctime
timestamps properly up to date. It does this by flushing local
data changes to the server before reporting mtime to applications
via system calls such as stat(2).
The Linux client handles atime updates more loosely, however.
NFS clients maintain good performance by caching data, but that
means that application reads, which normally update atime, are
not reflected to the server where a file's atime is actually
maintained.
Because of this caching behavior, the Linux NFS client does not
support generic atime-related mount options. See mount(8) for
details on these options.
In particular, the atime/noatime, diratime/nodiratime,
relatime/norelatime, and strictatime/nostrictatime mount options
have no effect on NFS mounts.
/proc/mounts may report that the relatime mount option is set on
NFS mounts, but in fact the atime semantics are always as
described here, and are not like relatime semantics.
Directory entry caching
The Linux NFS client caches the result of all NFS LOOKUP
requests. If the requested directory entry exists on the server,
the result is referred to as a positive lookup result. If the
requested directory entry does not exist on the server (that is,
the server returned ENOENT), the result is referred to as
negative lookup result.
To detect when directory entries have been added or removed on
the server, the Linux NFS client watches a directory's mtime. If
the client detects a change in a directory's mtime, the client
drops all cached LOOKUP results for that directory. Since the
directory's mtime is a cached attribute, it may take some time
before a client notices it has changed. See the descriptions of
the acdirmin, acdirmax, and noac mount options for more
information about how long a directory's mtime is cached.
Caching directory entries improves the performance of
applications that do not share files with applications on other
clients. Using cached information about directories can
interfere with applications that run concurrently on multiple
clients and need to detect the creation or removal of files
quickly, however. The lookupcache mount option allows some
tuning of directory entry caching behavior.
Before kernel release 2.6.28, the Linux NFS client tracked only
positive lookup results. This permitted applications to detect
new directory entries created by other clients quickly while
still providing some of the performance benefits of caching. If
an application depends on the previous lookup caching behavior of
the Linux NFS client, you can use lookupcache=positive.
If the client ignores its cache and validates every application
lookup request with the server, that client can immediately
detect when a new directory entry has been either created or
removed by another client. You can specify this behavior using
lookupcache=none. The extra NFS requests needed if the client
does not cache directory entries can exact a performance penalty.
Disabling lookup caching should result in less of a performance
penalty than using noac, and has no effect on how the NFS client
caches the attributes of files.
The sync mount option
The NFS client treats the sync mount option differently than some
other file systems (refer to mount(8) for a description of the
generic sync and async mount options). If neither sync nor async
is specified (or if the async option is specified), the NFS
client delays sending application writes to the server until any
of these events occur:
Memory pressure forces reclamation of system memory
resources.
An application flushes file data explicitly with sync(2),
msync(2), or fsync(3).
An application closes a file with close(2).
The file is locked/unlocked via fcntl(2).
In other words, under normal circumstances, data written by an
application may not immediately appear on the server that hosts
the file.
If the sync option is specified on a mount point, any system call
that writes data to files on that mount point causes that data to
be flushed to the server before the system call returns control
to user space. This provides greater data cache coherence among
clients, but at a significant performance cost.
Applications can use the O_SYNC open flag to force application
writes to individual files to go to the server immediately
without the use of the sync mount option.
Using file locks with NFS
The Network Lock Manager protocol is a separate sideband protocol
used to manage file locks in NFS version 3. To support lock
recovery after a client or server reboot, a second sideband
protocol -- known as the Network Status Manager protocol -- is
also required. In NFS version 4, file locking is supported
directly in the main NFS protocol, and the NLM and NSM sideband
protocols are not used.
In most cases, NLM and NSM services are started automatically,
and no extra configuration is required. Configure all NFS
clients with fully-qualified domain names to ensure that NFS
servers can find clients to notify them of server reboots.
NLM supports advisory file locks only. To lock NFS files, use
fcntl(2) with the F_GETLK and F_SETLK commands. The NFS client
converts file locks obtained via flock(2) to advisory locks.
When mounting servers that do not support the NLM protocol, or
when mounting an NFS server through a firewall that blocks the
NLM service port, specify the nolock mount option. NLM locking
must be disabled with the nolock option when using NFS to mount
/var because /var contains files used by the NLM implementation
on Linux.
Specifying the nolock option may also be advised to improve the
performance of a proprietary application which runs on a single
client and uses file locks extensively.
NFS version 4 caching features
The data and metadata caching behavior of NFS version 4 clients
is similar to that of earlier versions. However, NFS version 4
adds two features that improve cache behavior: change attributes
and file delegation.
The change attribute is a new part of NFS file and directory
metadata which tracks data changes. It replaces the use of a
file's modification and change time stamps as a way for clients
to validate the content of their caches. Change attributes are
independent of the time stamp resolution on either the server or
client, however.
A file delegation is a contract between an NFS version 4 client
and server that allows the client to treat a file temporarily as
if no other client is accessing it. The server promises to
notify the client (via a callback request) if another client
attempts to access that file. Once a file has been delegated to
a client, the client can cache that file's data and metadata
aggressively without contacting the server.
File delegations come in two flavors: read and write. A read
delegation means that the server notifies the client about any
other clients that want to write to the file. A write delegation
means that the client gets notified about either read or write
accessors.
Servers grant file delegations when a file is opened, and can
recall delegations at any time when another client wants access
to the file that conflicts with any delegations already granted.
Delegations on directories are not supported.
In order to support delegation callback, the server checks the
network return path to the client during the client's initial
contact with the server. If contact with the client cannot be
established, the server simply does not grant any delegations to
that client.
NFS servers control access to file data, but they depend on their
RPC implementation to provide authentication of NFS requests.
Traditional NFS access control mimics the standard mode bit
access control provided in local file systems. Traditional RPC
authentication uses a number to represent each user (usually the
user's own uid), a number to represent the user's group (the
user's gid), and a set of up to 16 auxiliary group numbers to
represent other groups of which the user may be a member.
Typically, file data and user ID values appear unencrypted (i.e.
"in the clear") on the network. Moreover, NFS versions 2 and 3
use separate sideband protocols for mounting, locking and
unlocking files, and reporting system status of clients and
servers. These auxiliary protocols use no authentication.
In addition to combining these sideband protocols with the main
NFS protocol, NFS version 4 introduces more advanced forms of
access control, authentication, and in-transit data protection.
The NFS version 4 specification mandates support for strong
authentication and security flavors that provide per-RPC
integrity checking and encryption. Because NFS version 4
combines the function of the sideband protocols into the main NFS
protocol, the new security features apply to all NFS version 4
operations including mounting, file locking, and so on. RPCGSS
authentication can also be used with NFS versions 2 and 3, but it
does not protect their sideband protocols.
The sec mount option specifies the security flavor used for
operations on behalf of users on that NFS mount point.
Specifying sec=krb5 provides cryptographic proof of a user's
identity in each RPC request. This provides strong verification
of the identity of users accessing data on the server. Note that
additional configuration besides adding this mount option is
required in order to enable Kerberos security. Refer to the
rpc.gssd(8) man page for details.
Two additional flavors of Kerberos security are supported: krb5i
and krb5p. The krb5i security flavor provides a
cryptographically strong guarantee that the data in each RPC
request has not been tampered with. The krb5p security flavor
encrypts every RPC request to prevent data exposure during
network transit; however, expect some performance impact when
using integrity checking or encryption. Similar support for
other forms of cryptographic security is also available.
NFS version 4 filesystem crossing
The NFS version 4 protocol allows a client to renegotiate the
security flavor when the client crosses into a new filesystem on
the server. The newly negotiated flavor effects only accesses of
the new filesystem.
Such negotiation typically occurs when a client crosses from a
server's pseudo-fs into one of the server's exported physical
filesystems, which often have more restrictive security settings
than the pseudo-fs.
NFS version 4 Leases
In NFS version 4, a lease is a period during which a server
irrevocably grants a client file locks. Once the lease expires,
the server may revoke those locks. Clients periodically renew
their leases to prevent lock revocation.
After an NFS version 4 server reboots, each client tells the
server about existing file open and lock state under its lease
before operation can continue. If a client reboots, the server
frees all open and lock state associated with that client's
lease.
When establishing a lease, therefore, a client must identify
itself to a server. Each client presents an arbitrary string to
distinguish itself from other clients. The client administrator
can supplement the default identity string using the
nfs4.nfs4_unique_id module parameter to avoid collisions with
other client identity strings.
A client also uses a unique security flavor and principal when it
establishes its lease. If two clients present the same identity
string, a server can use client principals to distinguish between
them, thus securely preventing one client from interfering with
the other's lease.
The Linux NFS client establishes one lease on each NFS version 4
server. Lease management operations, such as lease renewal, are
not done on behalf of a particular file, lock, user, or mount
point, but on behalf of the client that owns that lease. A
client uses a consistent identity string, security flavor, and
principal across client reboots to ensure that the server can
promptly reap expired lease state.
When Kerberos is configured on a Linux NFS client (i.e., there is
a /etc/krb5.keytab on that client), the client attempts to use a
Kerberos security flavor for its lease management operations.
Kerberos provides secure authentication of each client. By
default, the client uses the host/ or nfs/ service principal in
its /etc/krb5.keytab for this purpose, as described in
rpc.gssd(8).
If the client has Kerberos configured, but the server does not,
or if the client does not have a keytab or the requisite service
principals, the client uses AUTH_SYS and UID 0 for lease
management.
Using non-privileged source ports
NFS clients usually communicate with NFS servers via network
sockets. Each end of a socket is assigned a port value, which is
simply a number between 1 and 65535 that distinguishes socket
endpoints at the same IP address. A socket is uniquely defined
by a tuple that includes the transport protocol (TCP or UDP) and
the port values and IP addresses of both endpoints.
The NFS client can choose any source port value for its sockets,
but usually chooses a privileged port. A privileged port is a
port value less than 1024. Only a process with root privileges
may create a socket with a privileged source port.
The exact range of privileged source ports that can be chosen is
set by a pair of sysctls to avoid choosing a well-known port,
such as the port used by ssh. This means the number of source
ports available for the NFS client, and therefore the number of
socket connections that can be used at the same time, is
practically limited to only a few hundred.
As described above, the traditional default NFS authentication
scheme, known as AUTH_SYS, relies on sending local UID and GID
numbers to identify users making NFS requests. An NFS server
assumes that if a connection comes from a privileged port, the
UID and GID numbers in the NFS requests on this connection have
been verified by the client's kernel or some other local
authority. This is an easy system to spoof, but on a trusted
physical network between trusted hosts, it is entirely adequate.
Roughly speaking, one socket is used for each NFS mount point.
If a client could use non-privileged source ports as well, the
number of sockets allowed, and thus the maximum number of
concurrent mount points, would be much larger.
Using non-privileged source ports may compromise server security
somewhat, since any user on AUTH_SYS mount points can now pretend
to be any other when making NFS requests. Thus NFS servers do
not support this by default. They explicitly allow it usually
via an export option.
To retain good security while allowing as many mount points as
possible, it is best to allow non-privileged client connections
only if the server and client both require strong authentication,
such as Kerberos.
Mounting through a firewall
A firewall may reside between an NFS client and server, or the
client or server may block some of its own ports via IP filter
rules. It is still possible to mount an NFS server through a
firewall, though some of the mount(8) command's automatic service
endpoint discovery mechanisms may not work; this requires you to
provide specific endpoint details via NFS mount options.
NFS servers normally run a portmapper or rpcbind daemon to
advertise their service endpoints to clients. Clients use the
rpcbind daemon to determine:
What network port each RPC-based service is using
What transport protocols each RPC-based service supports
The rpcbind daemon uses a well-known port number (111) to help
clients find a service endpoint. Although NFS often uses a
standard port number (2049), auxiliary services such as the NLM
service can choose any unused port number at random.
Common firewall configurations block the well-known rpcbind port.
In the absense of an rpcbind service, the server administrator
fixes the port number of NFS-related services so that the
firewall can allow access to specific NFS service ports. Client
administrators then specify the port number for the mountd
service via the mount(8) command's mountport option. It may also
be necessary to enforce the use of TCP or UDP if the firewall
blocks one of those transports.
NFS Access Control Lists
Solaris allows NFS version 3 clients direct access to POSIX
Access Control Lists stored in its local file systems. This
proprietary sideband protocol, known as NFSACL, provides richer
access control than mode bits. Linux implements this protocol
for compatibility with the Solaris NFS implementation. The
NFSACL protocol never became a standard part of the NFS version 3
specification, however.
The NFS version 4 specification mandates a new version of Access
Control Lists that are semantically richer than POSIX ACLs. NFS
version 4 ACLs are not fully compatible with POSIX ACLs; as such,
some translation between the two is required in an environment
that mixes POSIX ACLs and NFS version 4.
Generic mount options such as rw and sync can be modified on NFS
mount points using the remount option. See mount(8) for more
information on generic mount options.
With few exceptions, NFS-specific options are not able to be
modified during a remount. The underlying transport or NFS
version cannot be changed by a remount, for example.
Performing a remount on an NFS file system mounted with the noac
option may have unintended consequences. The noac option is a
combination of the generic option sync, and the NFS-specific
option actimeo=0.
Unmounting after a remount
For mount points that use NFS versions 2 or 3, the NFS umount
subcommand depends on knowing the original set of mount options
used to perform the MNT operation. These options are stored on
disk by the NFS mount subcommand, and can be erased by a remount.
To ensure that the saved mount options are not erased during a
remount, specify either the local mount directory, or the server
hostname and export pathname, but not both, during a remount.
For example,
mount -o remount,ro /mnt
merges the mount option ro with the mount options already saved
on disk for the NFS server mounted at /mnt.
/etc/fstab
file system table
/etc/nfsmount.conf
Configuration file for NFS mounts
Before 2.4.7, the Linux NFS client did not support NFS over TCP.
Before 2.4.20, the Linux NFS client used a heuristic to determine
whether cached file data was still valid rather than using the
standard close-to-open cache coherency method described above.
Starting with 2.4.22, the Linux NFS client employs a Van
Jacobsen-based RTT estimator to determine retransmit timeout
values when using NFS over UDP.
Before 2.6.0, the Linux NFS client did not support NFS version 4.
Before 2.6.8, the Linux NFS client used only synchronous reads
and writes when the rsize and wsize settings were smaller than
the system's page size.
The Linux client's support for protocol versions depend on
whether the kernel was built with options CONFIG_NFS_V2,
CONFIG_NFS_V3, CONFIG_NFS_V4, CONFIG_NFS_V4_1, and
CONFIG_NFS_V4_2.
fstab(5), mount(8), umount(8), mount.nfs(5), umount.nfs(5),
exports(5), nfsmount.conf(5), netconfig(5), ipv6(7), nfsd(8),
sm-notify(8), rpc.statd(8), rpc.idmapd(8), rpc.gssd(8),
rpc.svcgssd(8), kerberos(1)
RFC 768 for the UDP specification.
RFC 793 for the TCP specification.
RFC 1813 for the NFS version 3 specification.
RFC 1832 for the XDR specification.
RFC 1833 for the RPC bind specification.
RFC 2203 for the RPCSEC GSS API protocol specification.
RFC 7530 for the NFS version 4.0 specification.
RFC 5661 for the NFS version 4.1 specification.
RFC 7862 for the NFS version 4.2 specification.
This page is part of the nfs-utils (NFS utilities) project.
Information about the project can be found at
⟨http:https://linux-nfs.org/wiki/index.php/Main_Page⟩. If you have a
bug report for this manual page, see
⟨http:https://linux-nfs.org/wiki/index.php/Main_Page⟩. This page was
obtained from the project's upstream Git repository
⟨git:https://git.linux-nfs.org/projects/steved/nfs-utils.git⟩ on
2023-12-22. (At that time, the date of the most recent commit
that was found in the repository was 2023-12-05.) If you
discover any rendering problems in this HTML version of the page,
or you believe there is a better or more up-to-date source for
the page, or you have corrections or improvements to the
information in this COLOPHON (which is not part of the original
manual page), send a mail to [email protected]
9 October 2012 NFS(5)
Pages that refer to this page: flock(1), pmdanfsclient(1), flock(2), filesystems(5), nfsmount.conf(5), nfsrahead(5), systemd.mount(5), blkmapd(8), mount(8), mountd(8), mount.nfs(8), nfsstat(8), rpcdebug(8), rpc.rquotad(8), sm-notify(8), statd(8), umount.nfs(8)
|
HTML rendering created 2023-12-22 by Michael Kerrisk, author of The Linux Programming Interface. For details of in-depth Linux/UNIX system programming training courses that I teach, look here. Hosting by jambit GmbH. |
|