pcp-mpstat(1) — Linux manual page

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | EXAMPLES | NOTES | ENVIRONMENT | PCP ENVIRONMENT | SEE ALSO | COLOPHON

PCP-MPSTAT(1)            General Commands Manual           PCP-MPSTAT(1)

NAME         top

       pcp-mpstat - Report CPU and interrupt related statistics.

SYNOPSIS         top

       pcp [pcp options] mpstat [ -A ] [ -u ] [ -V ] [ -I { SUM | CPU |
       SCPU | ALL } ] [ -P { cpu1,cpu2 [,...] | ON | ALL } ] [ -t
       interval ] [ -s count ] [ -a archive ] [ -? ]

DESCRIPTION         top

       pcp-mpstat command writes to standard output activities for each
       available processor, processor 0 being the first one.  If no
       activity/option has been selected, then the default report is the
       CPU utilization (-u) report.

       The interval parameter specifies the amount of time in seconds
       between each report.  The default is one second.  The value of
       count parameter determines the number of samples to be displayed.
       The default is continous.

OPTIONS         top

       When invoked via the pcp(1) command, the -h/--host, -a/--archive,
       -O/--origin, -s/--samples, -t/--interval, -Z/--timezone and
       several other pcp options become indirectly available; refer to
       PCPIntro(1) for a complete description of these options.

       The additional command line options available for pcp-mpstat are:

       -A     This option is equivalent to specifying -u -I ALL -P ALL

       -I { SUM | CPU | SCPU | ALL }
              Report interrupts statistics.
              With the SUM keyword, the pcp-mpstat command reports the
              total number of interrupts per processor.  The following
              values are displayed:

       CPU
                     Processor number.  The keyword all indicates that
                     statistics are calculated as averages among all
                     processors.

              intr/s
                     Show the total number of interrupts received per
                     second by the CPU or CPUs.

              With the CPU keyword, the number of each individual
              interrupt received per second by the CPU or CPUs is
              displayed.  Interrupts are those under the
              kernel.percpu.interrupts metric tree.

              With the SCPU keyword, the number of each individual
              software interrupt received per second by the CPU or CPUs
              is displayed.  Software interrupts are those under the
              kernel.percpu.softirqs tree

              The ALL keyword is equivalent to specifying all the
              keywords above and therefore all the interrupts statistics
              are displayed.

       -P { cpu1,cpu2[,...] | ON | ALL }
              Indicate the processor number for which statistics are to
              be reported.  cpu1 and cpu2 are the processor numbers.  A
              list of required processor numbers can be provided.  Note
              that processor 0 is the first processor.

              The ON keyword indicates that statistics are to be
              reported for every online processor, whereas the ALL
              keyword indicates that statistics are to be reported for
              all processors.

       -u     Report CPU utilization.  The following values are
              displayed:

              CPU
                     Processor number.  The keyword ALL indicates that
                     statistics are calculated as averages among all
                     processors.

              %usr
                     Show the percentage of CPU utilization that
                     occurred while executing at the user level
                     (application).

              %nice
                     Show the percentage of CPU utilization that
                     occurred while executing at the user level with
                     nice priority.

              %sys
                     Show the percentage of CPU utilization that
                     occurred while executing at the system level
                     (kernel).  Note that this does not include time
                     spent servicing hardware and software interrupts.

              %iowait
                     Show the percentage of time that the CPU or CPUs
                     were idle during which the system had an
                     outstanding disk I/O request.

              %irq
                     Show the percentage of time spent by the CPU or
                     CPUs to service hardware interrupts.

              %soft
                     Show the percentage of time spent by the CPU or
                     CPUs to service software interrupts.

              %steal
                     Show the percentage of time spent in involuntary
                     wait by the virtual CPU or CPUs while the
                     hypervisor was servicing another virtual processor.

              %guest
                     Show the percentage of time spent by the CPU or
                     CPUs to run a virtual processor.

              %gnice
                     Show the percentage of time spent by the CPU or
                     CPUs to run a niced guest.

              %idle
                     Show the percentage of time that the CPU or CPUs
                     were idle and the system did not have an
                     outstanding disk I/O request.

              Note: On SMP machines a processor that does not have any
              activity at all is a disabled (offline) processor.

       -s  N , --samples = N
              Set the number of samples to be displayed.  Since the
              first sample is used for the rate conversion of some of
              the metrics, the total number of samples reported are one
              less that N.  Default is continous.

       -t DELTA , --interval = DELTA
              Set the interval between two samples.  The default is one
              second.

       -a  FILE , --archive = FILE
              Causes pcp-mpstat to use the specified archive than
              connecting to PMCD.  The argument to -a is a comma-
              separated list of names, each of which may be the base
              name of an archive or the name of a directory containing
              one or more archives.

       -V , --version
              Print version number then exit.

       -? , --help
              Print usage message then exit.

EXAMPLES         top

       pcp-mpstat -t 2 -s 5
              Display four reports of global statistics among all
              processors at two second intervals.

       pcp mpstat -P ALL -t 2 -s 5
              Display four reports of statistics for all processors at
              two second intervals.

NOTES         top

       pcp-mpstat is inspired by the mpstat(1) command and aims to be
       command line and output compatible with it.

ENVIRONMENT         top

       TZ and LC_TIME environment variables can be used to override the
       default date display format for pcp-mpstat.

PCP ENVIRONMENT         top

       Environment variables with the prefix PCP_ are used to
       parameterize the file and directory names used by PCP.  On each
       installation, the file /etc/pcp.conf contains the local values
       for these variables.  The $PCP_CONF variable may be used to
       specify an alternative configuration file, as described in
       pcp.conf(5).

       For environment variables affecting PCP tools, see
       pmGetOptions(3).

SEE ALSO         top

       PCPIntro(1), pcp(1), mpstat(1), pmParseInterval(3),
       pmTraversePMNS(3) and environ(7).

COLOPHON         top

       This page is part of the PCP (Performance Co-Pilot) project.
       Information about the project can be found at 
       ⟨http:https://www.pcp.io/⟩.  If you have a bug report for this manual
       page, send it to [email protected].  This page was obtained from the
       project's upstream Git repository
       ⟨https://github.com/performancecopilot/pcp.git⟩ on 2023-12-22.
       (At that time, the date of the most recent commit that was found
       in the repository was 2023-12-16.)  If you discover any rendering
       problems in this HTML version of the page, or you believe there
       is a better or more up-to-date source for the page, or you have
       corrections or improvements to the information in this COLOPHON
       (which is not part of the original manual page), send a mail to
       [email protected]

Performance Co-Pilot               PCP                     PCP-MPSTAT(1)