Skip to content

Latest commit

 

History

History
199 lines (140 loc) · 6.08 KB

README-router.md

File metadata and controls

199 lines (140 loc) · 6.08 KB
Raw

zerotier router

Description

This is a variation built on top of the zyclonite/zerotier container which implements a local network router. It is based upon the ZeroTier Knowledge Base article:

Technically, this could be described as a half-router:

  • You can initiate connections from a remote client to devices on the LAN; but
  • You can't initiate connections to the remote client from devices on the LAN.

Command line example

$ docker run --name zerotier-one --device=/dev/net/tun \
  --cap-add=NET_ADMIN --cap-add=NET_RAW --cap-add=SYS_ADMIN \
  --env TZ=Etc/UTC --env PUID=999 --env PGID=994 \
  --env ZEROTIER_ONE_LOCAL_PHYS=eth0 \
  --env ZEROTIER_ONE_USE_IPTABLES_NFT=false \
  --env ZEROTIER_ONE_GATEWAY_MODE=inbound \
  --env ZEROTIER_ONE_NETWORK_IDS=«yourDefaultNetworkID(s)» \
  -v /var/lib/zerotier-one:/var/lib/zerotier-one zyclonite/zerotier:router

Note:

  • Environment variables that can contain multiple values should be enclosed in quotes with the components separated by spaces. Example:

     --env ZEROTIER_ONE_LOCAL_PHYS="eth0 wlan0"

Compose file example

version: '3'
services:
  zerotier:
    image: "zyclonite/zerotier:router"
    container_name: zerotier-one
    devices:
      - /dev/net/tun
    network_mode: host
    volumes:
      - '/var/lib/zerotier-one:/var/lib/zerotier-one'
    cap_add:
      - NET_ADMIN
      - SYS_ADMIN
      - NET_RAW
    restart: unless-stopped
    environment:
      - TZ=Etc/UTC
      - PUID=999
      - PGID=994
      - ZEROTIER_ONE_LOCAL_PHYS=eth0
      - ZEROTIER_ONE_USE_IPTABLES_NFT=false
      - ZEROTIER_ONE_GATEWAY_MODE=inbound
    # - ZEROTIER_ONE_NETWORK_IDS=«yourDefaultNetworkID(s)»

Note:

  • The right hand sides of environment variables should never be enclosed in quotes. If you need to pass multiple values, separate them with spaces. Example:

     environment:
 - ZEROTIER_ONE_LOCAL_PHYS=eth0 wlan0

Environment variables

  • TZ – timezone support. Example:

     environment:
 - TZ=Australia/Sydney

    Defaults to Etc/UTC if omitted.

  • PUID + PGID – user and group IDs for ownership of persistent store. Example:

     environment:
 - PUID=1000
 - PGID=1000

    If omitted, PUID defaults to user ID 999, while PGID defaults to group ID 994.

    These variables are only used to ensure consistent ownership of persistent storage on each launch. They do not affect how the container runs. Absent a user: directive, the container runs as root and does not downgrade its privileges.

  • ZEROTIER_ONE_LOCAL_PHYS - a space-separated list of physical interfaces that should be configured to participate in NAT-based routing. Examples:

    • Use only the physical Ethernet interface (this is also the default of the variable is omitted):

       environment:
 - ZEROTIER_ONE_LOCAL_PHYS=eth0

    • If your computer only has WiFi active (eg Raspberry Pi Zero W2):

       environment:
 - ZEROTIER_ONE_LOCAL_PHYS=wlan0

    • If your computer has both Ethernet and WiFi interfaces active and you wish to be able to route through each interface:

       environment:
 - ZEROTIER_ONE_LOCAL_PHYS=eth0 wlan0

      This scheme could be appropriate where the physical interfaces were:

      1. In the same broadcast domain (subnet). Disconnecting Ethernet would fail-over to WiFi.
      2. In different broadcast domains, such as if you allocated different subnets for Ethernet and WiFi.

  • ZEROTIER_ONE_USE_IPTABLES_NFT - controls the command the container uses to set up NAT forwarding. Example:

     environment:
 - ZEROTIER_ONE_USE_IPTABLES_NFT=true
    • false means the container uses iptables. This is the default.
    • true means the container uses iptables-nft.

    Try true if NAT does not seem to be working. This is needed on Raspberry Pi Bullseye.

  • ZEROTIER_ONE_GATEWAY_MODE - controls the traffic direction. Examples:

    • Only permit traffic from the ZeroTier cloud to the local physical interfaces:

       environment:
 - ZEROTIER_ONE_GATEWAY_MODE=inbound

    • Only permit traffic from the local physical interfaces to the ZeroTier cloud:

       environment:
 - ZEROTIER_ONE_GATEWAY_MODE=outbound

    • Permit bi-directional traffic between the local physical interfaces and the ZeroTier cloud:

       environment:
 - ZEROTIER_ONE_GATEWAY_MODE=both

    Defaults to inbound if omitted. Note that you will probably need one or more static routes configured in your local LAN router so that traffic originating in a local host which is not running the ZeroTier client can be directed to the gateway host.

  • ZEROTIER_ONE_NETWORK_IDS – a space-separated list of ZeroTier network IDs.

    This variable is only effective on first launch. There is no default if it is omitted. Examples:

    • to join a single network:

       environment:
 - ZEROTIER_ONE_NETWORK_IDS=aaaaaaaaaaaaaaaa

      Equivalent of running the following command after the container first starts:

       $ docker exec zerotier zerotier-cli join aaaaaaaaaaaaaaaa

    • to join a multiple networks:

       environment:
 - ZEROTIER_ONE_NETWORK_IDS=aaaaaaaaaaaaaaaa bbbbbbbbbbbbbbbb

      Equivalent of running the following commands after the container first starts:

       $ docker exec zerotier zerotier-cli join aaaaaaaaaaaaaaaa
 $ docker exec zerotier zerotier-cli join bbbbbbbbbbbbbbbb

    It does not matter whether you use this environment variable or the join command, you still need to use ZeroTier Central to approve the computer for each network it joins.

Managed route(s)

For each ZeroTier container that is configured as a router, ZeroTier needs at least one Managed Route.

The ZeroTier Wiki explains how to design managed routes.

You configure Managed Routes in ZeroTier Central.