Built by Jacob Bruce and Nathan Shelly

This project aims to walk through the steps of designing and building a webcam from scratch. We'll walk through PCB (printed circuit board) design, soldering of components, 3D printing of the outer enclosure, MCU code and website code to enable you to make your own webcam, or modify our design however you'd like! This repository acts as the landng page to various parts of the project. Here we'll have various files such as our PCB designs, our CAD files and a bill of materials. We'll link to two different code repositories, one for our MCU code and one for our website code.

Here are some potential places to order from: Mouser, Digikey, Robotshop.

You'll also need to order the PCB to solder the components onto. We've included our raw EAGLE files, as well as a set of Gerber files that can be sent directly to the manufacturer.

If you have experience with surface mount soldering, this should be fairly straightforward. If you do not, we recommend practicing some before working with any expensive components. This playlist has many useful videos for this project, including several specifically on soldering.

We recommend the following soldering order to unit test each component before moving forward.

1. Power circuit: barrel jack, voltage regulator, power indicator LED, associated resistors and capacitors. Confirm that ground and power are not connected via continuity test. Plug in power cord and confirm that the power indicator lights up.

2. Microcontroller, PLL circuit, crystal oscillator, buttons, associated bypass capacitors, and header pins. After soldering the MCU, confirm each connection via continuity test to another via or pad, and confirm that no pins are connected to power or ground that shouldn't be. Connect the Atmel debugger, power the circuit, and confirm that the device signature can be read from Atmel Studio.

3. Wifi Chip, indicator LEDs, header pins, and associated bypass capacitors. Again, confirm each connection individually before proceeding. To confirm proper operation, perform step 4 to configure the chip.

4. Microphone and associated passive components.

5. Camera module and associated passive components. Be sure to solder the connector without the module inserted, and again confirm connections individually before proceeding.

The wifi chip requires a fair degree of configuration to work correctly. Zentri helpfully includes an OS to which commands are issued, and it's quite easy to work with their command API. We recommend issuing these commands via a terminal emulator (TeraTerm for windows or CoolTerm for Mac) connected to the header pins for the UART communication via an FTDI cable. If you use the FTDI cable, make sure that the microcontroller will not be attempting to use the UART bus (either because no code has been loaded onto it or because it does not configure or use its UART module), or bus contention will result. These operations can also be performed by editing the MCU code and running commands, but that's much more difficult and harder to read/interpret feedback.

1. Connect to the chip. Confirm your connection by hitting Enter; the chip should respond with Ready.
2. If you're using a network which requires registration, obtain its mac address via the get wl m query, and register it to the network.
3. Connect the device to your network with the setup command. Once the command has been run, find the device's network on your computer. Connect to it, visit setup.com, and follow the prompts to connect to the desired network. Thereafter, the web console can be accessed from https://zentrios-XYZ.local/, where XYZ are the last 3 digits of your wifi chip's serial number.
4. Register with Zentri, and claim your device via the dms claim command.
5. Update the device's firmware with the OTA command.
6. Set the indicator GPIOs to indicate on the correct LEDs by running the following commands:

set sy i g wlan 20
set sy i g network 21
set sy i g softap 22

7. Load TLS certificate onto the chip using its file uploader. Change its default tls certificate to this file via the ne t a command.

8. Change the baud rate by setting the ua b variable for UART1. The default speed for UART1 is 115200, and our system is designed to run at 2.5Mbauds. You may want to turn the baud rate down in the MCU code to test operation before turning both up to this high speed - we haven't found a terminal emulator that can successfully interpret messages at this speed, and any issues can be difficult to debug.

To load our code onto the microcontroller, first connect your Atmel debugger to the corresponding header pins and to your computer. Open our Atmel project, and connect to the debugger. Compile and load the code - it should run correctly now that the wifi chip is properly configured.

For designing the enclosure we used an online program called Onshape. This provides a convenient way to edit CAD files with low overhead though it lacks some functionality from a fuller editor like Solidworks. View our Onshape project here.

We've also provided the raw files in two different formats. If you'd like to modify our design here are .sldprt files. If you'd like to print our design as is here are .stl files.