Skip to content

Latest commit

 

History

History

syn

README.md

This synthesis flow is experimental and under development, it does not produce tape-out quality netlists and area/timing numbers it generates are not representative of what would be achievable with a tape-out quality flow

Yosys/OpenSTA Ibex Synthesis Flow

This is a synthesis-only implementation flow using Yosys for Synthesis and OpenSTA to produce timing reports. Its outputs are:

  • A pre-mapping netlist - Gate-level verilog using generic gates that hasn't been mapped to a standard-cell library yet
  • A post synthesis netlist - Gate-level verilog after optimisation mapped to a standard-cell library
  • An STA netlist - Logically equivilent to the netlist above but with changes to allow processing by OpenSTA
  • Area/Cell Usage report - Total area consumed by utilised cells and counts of each cell instance used
  • Timing reports - Overal timing report and reports broken down into various path groups (register to register paths and per IO reports)

Yosys doesn't yet support the full subset of SystemVerilog used by Ibex so the sv2v tool is used to first convert the Ibex RTL into the SystemVerilog subset Yosys can process.

Synthesis flow requirements

The following must be installed:

The flow was tested with yosys 0.9 and OpenSTA 2.2 but may work with other versions. A standard cell library is also required in the liberty (.lib) format. The following Open Libraries can be used:

Synthesis flow setup

The synthesis flow is configured via environment variables. The syn_setup.sh file is used to set the environment variables for the flow and any changes made should be placed there. An example syn_setup.example.sh is included. A copy of this named syn_setup.sh must be made and the values in it set appropriately for the flow to work.

The environment variables that must be set in syn_setup.sh are

  • LR_SYNTH_CELL_LIBRARY_PATH - The path to the standard cell library, this should point to the absolute path of the Nangate45 library (NangateOpenCellLibrary_typical.lib).
  • LR_SYNTH_CELL_LIBRARY_NAME - The name of the standard cell library, this is used to alter the flow configuration for the library, currently 'nangate' is the only supported value

Running the synthesis flow

Once syn_setup.sh has been created, call syn_yosys.sh to run the entire flow. All outputs are placed under the syn/syn_out directory with the prefix ibex_ with the current date/time forming the rest of the name, e.g. syn/syn_out/ibex_06_01_2020_11_19_15

  • syn/syn_out/ibex_date
    • reports - All of the generated reports
      • area.rpt - Total area used and per cell instance counts
      • timing
        • *.rpt - Raw reports from OpenSTA, gives full paths
        • *.csv.rpt - CSV reports gives start and end point and slack
      • log
        • syn.log - Log of the Yosys run
        • sta.log - Log of the OpenSTA run
      • generated
        • *.v - Ibex RTL after sv2v processing
        • ibex_top.pre_map.v - Pre-mapping synthesis netlists
        • ibex_top_netlist.v - Post-synthesis netlist
        • ibex_top_netlist.sta.v - Post-synthesis netlist usable by OpenSTA
        • ibex_top.[library-name].out.sdc - Generated .sdc timing constraints file

If you wish to change the results directory naming or location edit syn_setup.sh appropriately.

Timing constraints

Two files specify the timing constraints and timing related settings for the flow. These are used to generate a single .sdc file

  • ibex_top_lr_synth_core.tcl - This specifies the constraints on all inputs and outputs as a fraction of a clock cycle, the names of the clock and reset inputs and the desired clock period in ps
  • ibex.[library-name].sdc - Header to include in generated .sdc file. Settings can be library dependent so the LR_SYNTH_CELL_LIBRARY_NAME environment varible is used to supply the [library-name] part of the name

Timing reports

Timing reports are produced for the following path groups

  • Overall - Every path in the design, WNS (worst negative slack) from this report is the design WNS that limits the frequency
  • reg2reg - Paths from register to register
  • in2reg - Paths from any input to any register
  • reg2out - Paths from any register to any output
  • in2out - Paths from any input to any output

They are available in two formats .rpt and .csv.rpt. The .rpt is the full output from OpenSTA and gives the full path between the start and end points. The CSV version contains the start-point, end-point and WNS (one path per line). CSV reports have had their start and end points translated to human readable names (though this isn't 100% reliable). The raw OpenSTA reports generally contain only generated cell names so will require further netlist inspection (via Yosys or simply looking at the netlist .v) to make sense of.

Post-synthesis inspection

Both Yosys and OpenSTA can be run to perform further inspection on the generated synthesis. TCL is provided to setup the tools appropriately.

First the environment variables must be setup for the flow and the directory containing the synthesis output set. This can be done with syn_setup.sh

$ source syn_setup.sh syn_out_06_01_2020_11_19_15/

Where syn_out_06_01_2020_11_19_15/ is directory containing the synthesis outputs. Then start Yosys or OpenSTA and run one of the provided TCL files

  • ./tcl/yosys_pre_map.tcl - Loads the pre-mapping netlist
  • ./tcl/yosys_post_synth.tcl - Load the post-synthesis netlist

So to load the post-synthesis netlist in Yosys:

$ yosys
yosys> tcl ./tcl/yosys_post_synth.tcl

To open the design in OpenSTA

$ sta
% source ./tcl/sta_open_design.tcl