Skip to content

Latest commit

 

History

History
233 lines (170 loc) · 9.27 KB

TROUBLESHOOTING.md

File metadata and controls

233 lines (170 loc) · 9.27 KB

Troubleshooting

The installation and setup of Shairport Sync is straightforward on recent Linux distributions. Issues can occasionally arise caused by problems elsewhere in the system, typically WiFi reception and/or the WiFi adapter settings, the network, the router, firewall settings or some more esoteric audio interfaces.

In this brief document will be listed some problems and some solutions, some provided by other users.

  1. Before starting, ensure that your software is up-to-date.
  2. Set the interpolation in the general section of the configuration file to basic as the soxr setting can cause lower-powered devices to bog down at critical times, e.g. see this report.

WiFi adapter running in power-saving / low-power mode

Check Throughput

You can check WiFi throughput using, for example, https://thepi.io/how-to-use-your-raspberry-pi-to-monitor-broadband-speed/

Problem

Shairport Sync is installed and running, but sometimes it disappears from the network, and sometimes it suffers from long dropouts.

Possible Cause

This can be caused by lots of things, but one of them is that the WiFi adapter may be set to run in a low-power or power-saving mode. If it's not busy, then after a while it goes into a low-power mode. This is bad as the device needs to be always connected to the network to provide the AirPlay service. You need to turn off power-saving mode. How you do this varies with platform and with WiFi adapter – internet search is your friend. Here, for instance, is the command for the C.H.I.P. from Next Thing Co, which has built in WiFi and Linux and has the iw command installed:

iw dev wlan0 set power_save off

Here is the command sequence for a Raspberry Pi 3, which has built-in WiFi:

sudo iwconfig wlan0 power off

Alternatively, (also for the Raspberry Pi), add the following line:

wireless-power off

to the file /etc/network/interfaces.

Here is another option, suggested by davidhq in #653:

$ sudo nano /etc/network/if-up.d/off-power-manager

Type:

#!/bin/sh
/sbin/iwconfig wlan0 power off

Then:

sudo chmod +x /etc/network/if-up.d/off-power-manager

There are some more details in some the closed issues on this repository.

Faulty WiFi

For an example of what it can take to track down a bad WiFi situation – in this case, a faulty WiFi adapter – please look at this report.

Can't play from iTunes on Windows

Problem

You can play from other devices but not from your Windows PC.

Possible Solution

Allow network discovery. This setting creates a private type network and enables Windows to access the ports and protocols necessary to use Shairport Sync.

UFW firewall blocking connections on Raspbian (Raspberry Pi)

Problem

You have installed Shairport Sync successfully, the daemon is running, you can see it from your remote terminal but you are unable to play a song.

Before you change anything to your configuration

  • Type the following command:

    sudo ufw disable

  • Try to launch a song from your remote device on the Shairport-sync one, if this works, proceed to the next step and follow the ones described below, in the solution section.

  • Enable UFW through the following command:

    sudo ufw enable

Solution

You have to allow connections to your Pi from remote devices. To do so, after re-enabling UFW (see last step of the previous section), enter the following commands in shell:

sudo ufw allow from 192.168.1.1/16 to any port 3689 proto tcp
sudo ufw allow from 192.168.1.1/16 to any port 5353
sudo ufw allow from 192.168.1.1/16 to any port 5000:5005 proto tcp
sudo ufw allow from 192.168.1.1/16 to any port 6000:6005 proto udp
sudo ufw allow from 192.168.1.1/16 to any port 35000:65535 proto udp

You may have to change the IP addresses range depending on your own local network settings.

You can check UFW config by typing sudo ufw status in shell. Please make sure that UFW is active, especially if you have deactivated it previously for testing purpose.

Run your song from your remote device. Enjoy !

Shairport Sync Won't Start Automatically After Reboot

This refers to slower machines, such as the Raspberry Pi Zero or the original (single core) Raspberry Pi, running a recent Linux that uses systemd.

Problem

Having compiled Shairport Sync properly using the README guide, and having completed the make install step, and having enabled startup on reboot using $ sudo systemctl enable shairport-sync, Shairport Sync will start manually upon entering $sudo systemctl enable shairport-sync, but it will not start automatically after a reboot.

Possible Cause

On lower-powered machines, such as the Raspberry Pi Zero or the original (single core) Raspberry Pi, particularly with a USB sound card, it may be that the sound system is not ready when Shairport Sync is automatically started. The result is that Shairport Sync cannot see the device it needs and shuts down.

Possible Solution

A good solution is to delay the automatic startup of Shairport Sync by a few seconds using the systemd timer mechanism:

Create a file called shairport-sync.timer and place it alongside shairport-sync.service in /lib/systemd/system. The file should contain the following:

[Unit]
Description=Shairport Sync AirPlay receiver

[Timer]                       
OnBootSec=10s              
Unit=shairport-sync.service

[Install]    
WantedBy=multi-user.target  

You need to disable the shairport-sync service because the timer is calling the service, and you need to enable the shairport-sync timer:

# systemctl disable shairport-sync
# systemctl start shairport-sync.timer
# systemctl enable shairport-sync.timer

See also #179, with thanks to @maumi and others.

Alternative Solution

  • Edit Shairport Sync service file sudo nano /lib/systemd/system/shairport-sync.service
  • Update the service section to include the line ExecStartPre=/bin/sleep 5

Example:

[Service]
ExecStartPre=/bin/sleep 5
ExecStart=/usr/local/bin/shairport-sync
User=pi
Group=pi

Stuttering audio on certain USB DACs (such as the Creative Soundblaster MP3+)

Problem When using a USB DAC on a Raspberry Pi audio plays fine through other methods (such as through mpd, mopidy, mplayer or aplay) but when streamed to Shairport Sync regular dropouts or stutters are heard.

Possible Cause There is a suspicion (although this is not 100% confirmed) that this is a fun latency/timing issue related to a combination of

  • The Raspberry Pi's ethernet itself being a USB device resulting in shared bandwidth/interrupts with USB DACs
  • Shairport Sync continually checking the latency of the USB DAC to maintain synchronisation of audio
  • Quirky USB DACs (already known to be problematic on the Raspberry Pi more info available here For more discussion on this issue see issue 167 or read on for the quick fix!

Possible Solution To get nice smooth audio first check the details of your USB DAC by either using 'aplay -l' which will give you output something like this:

**** List of PLAYBACK Hardware Devices ****
card 0: ALSA [bcm2835 ALSA], device 0: bcm2835 ALSA [bcm2835 ALSA]
  Subdevices: 8/8
  Subdevice #0: subdevice #0
  Subdevice #1: subdevice #1
  Subdevice #2: subdevice #2
  Subdevice #3: subdevice #3
  Subdevice #4: subdevice #4
  Subdevice #5: subdevice #5
  Subdevice #6: subdevice #6
  Subdevice #7: subdevice #7
card 0: ALSA [bcm2835 ALSA], device 1: bcm2835 ALSA [bcm2835 IEC958/HDMI]
  Subdevices: 1/1
  Subdevice #0: subdevice #0
card 1: MP3 [Sound Blaster MP3+], device 0: USB Audio [USB Audio]
  Subdevices: 0/1
  Subdevice #0: subdevice #0

or look at your exisiting '/etc/asound.conf' file, which may look something like this

pcm.!default {
    type hw
    card 1
}
ctl.!default {
    type hw
    card 1
}

The important information you want is the card number which in this case is 1.

Now modify your 'etc/asound.conf' file (or create one if it doesn't exist) using the following template substituting the 'pcm "hw:1"' and 'card 1' sections with the card number of your device

pcm.!default {
    type plug
    slave.pcm {
        type dmix
        ipc_key 1024
        slave {
            pcm "hw:1"
            rate 48000        # this line is only needed for USB DACs which only support 48khz
            period_time 0
            period_size 1920
            buffer_size 19200
        }
    }
}
ctl.!default {
    type hw
    card 1
}

This sets the default alsa audio device to be the USB DAC via a dmixer plugin (which can be used by multiple applications at once) using a modified period and buffer size and optionally mix to 48khz.

This will then be used by default by Shairport-Sync and any other applications using alsa.

Note that some distributions (such as Volumio 2) don't use an asound.conf file by default, they instead specify the hardware details directly in '/etc/mpd.conf' files so some more in-depth modification is needed to override this.

(Note: not tested by Mike B.)