Hikvision Camera Stream setup

[travismailsa]

Hi,

I am new to Frigate and configuration, but i cannot find clear documentation as how to setup/config a single Hikvision camera to the frigate.yml file. If i remove my camera stream setup, Frigate starts. If i add the setup - what i have managed to find through videos, it crashes. No clue where to start - help would be much appreciated.

"cameras:
...
ffmpeg:
inputs:
- path: rtsp:https://xxx:[email protected]:554/Streaming/Channels/101
roles:
- detect
- record
rtmp:
enabled: True
record:
enabled: True
snapshots:
enabled: True
detect:
enabled: True
width: 1280
height: 720
fps: 5
objects:
track:
- person
- cars
"
RTSP url is correct and working

[schford]

Mine below for one hikvision camera if that helps. Don't think you need that port in url.

go2rtc:
streams:
garage:
- rtsp:https://admin:[email protected]/Streaming/Channels/101
garage_sub:
- rtsp:https://admin:[email protected]/Streaming/channels/102 # 6frames

garage_camera:
ffmpeg:
hwaccel_args: preset-vaapi # Use Intel NUC iGPU (optional)
inputs:
- path: rtsp:https://127.0.0.1:8554/garage_sub
input_args: preset-rtsp-restream
roles:
- detect
- path: rtsp:https://127.0.0.1:8554/garage
input_args: preset-rtsp-restream
roles:
- record
detect:
enabled: true # <---- disable detection until you have a working camera feed
width: 640 # <---- update for your camera's resolution
height: 480 # <---- update for your camera's resolution
fps: 6
objects:
track:
- person
- dog
- cat
- car
- bicycle
motion:
mask:
- 145,37,217,41,217,0,143,0
snapshots:
enabled: true
required_zones:
- drive_steps
record:
enabled: true
events:
required_zones:
- drive_steps
retain:
default: 10
live:
stream_name: garage

zones:
  drive_steps:
    coordinates: 248,165,192,0,0,0,0,480,431,480,410,437,613,303,593,91

[travismailsa]

Can i not at more virtual cores instead of just setting it to cpu0 ? Because as far as i am aware the VM wouldnt recoginse them as threads for the added command?

[travismailsa]

Add more here?

detectors:
cpu0:
type: cpu

[NickM-27]

You can add more cpu detectors

[travismailsa]

@NickM-27 , 100% right, maxing out my cpu shown below on ESZXI -shite

[schford]

https://www.desertcart.co.za/products/125589101-google-coral-usb-edge-tpu-ml-accelerator-coprocessor-for-raspberry-pi-and-other-embedded-single-board-computers

[travismailsa]

https://www.desertcart.co.za/products/125589101-google-coral-usb-edge-tpu-ml-accelerator-coprocessor-for-raspberry-pi-and-other-embedded-single-board-computers

Much aprreciaed and thanked, but desertcart.co.za is a dropshipping site from Aliexpress - never know what you are going to get or if it will ever arrive in the country .

Think ill buy the unit from a European reputable supplier i think and pay the hefty custom fees using DHL and FEDEK etc- ive seen its only around 70$..

I might move my HA over to my gaming PC and run a test with my RTX 3080

[schford]

the coral works super super well if you do get the chance to lay your hands on one.

Cheers

Stuart

[travismailsa]

Thanks a lot mate for taking the time to reply.
If my thread does not get closed i will post the results - whether it solved the issue or now
Cheers
Travis

[Cold-Lemonade]

@travismailsa I am trying to set up a Anpviz camera, but Frigate's ffmpeg keeps dropping it. I believe the Anpviz camera is the same (more or less) to Hikvision. Would you be so kind as to share your config.yml code that you used to configure your Hikvision camera? I'd like to see how you did it. Thanks.