forked from viesturz/tapchanger
-
Notifications
You must be signed in to change notification settings - Fork 0
/
T0-burner-dragon.cfg
88 lines (77 loc) · 1.84 KB
/
T0-burner-dragon.cfg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
# This file contains common pin mappings for the BIGTREETECH EBBCan
# Canbus board. To use this config, the firmware should be compiled for the
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
# See docs/Config_Reference.md for a description of parameters.
[mcu et0]
canbus_uuid:bafd9b10a1b4
[extruder]
step_pin: et0:PD0
dir_pin: !et0:PD1
enable_pin: !et0:PD2
microsteps: 16
rotation_distance: 22.92 # #22.23
gear_ratio: 50:10
nozzle_diameter: 0.400
filament_diameter: 1.750
heater_pin: et0:PB13
sensor_type: MAX31865
sensor_pin: et0:PA4
spi_bus: spi1
rtd_nominal_r: 100
rtd_reference_r: 430
rtd_num_of_wires: 2
control: pid
pid_Kp=28.698
pid_Ki=1.952
pid_Kd=105.465
min_temp: -10
max_temp: 300
min_extrude_temp: 180
pressure_advance: 0.035 # See tuning pressure advance doc
pressure_advance_smooth_time: 0.040
[tmc2209 extruder]
uart_pin: et0:PA15
run_current: 0.45
hold_current: 0.1
driver_TPOWERDOWN: 20
stealthchop_threshold: 999999
[multi_fan T0_partfan]
pin: et0:PA0
[heater_fan T0_hotend_fan]
pin: et0:PA1
heater: extruder
heater_temp: 50.0
[adxl345]
cs_pin: et0:PB12
spi_software_sclk_pin: et0:PB10
spi_software_mosi_pin: et0:PB11
spi_software_miso_pin: et0:PB2
axes_map: x,z,y
[gcode_macro T0]
variable_color: ""
gcode:
SELECT_TOOL T=0
[tool T0]
tool_number: 0
extruder: extruder
params_type: 'rods_mini_hookon'
fan: multi_fan T0_partfan
gcode_x_offset: 0
gcode_y_offset: 0
gcode_z_offset: 0
params_park_x: 0.0
params_park_y: -7.7
params_park_z: 349.5
[tool_probe T0]
pin: et0:PB6
tool: 0
z_offset: -0.948
speed: 5.0
samples: 3
samples_result: median
sample_retract_dist: 2.0
samples_tolerance: 0.02
samples_tolerance_retries: 3
activate_gcode:
_TAP_PROBE_ACTIVATE HEATER=extruder