forked from gsliepen/tinc
-
Notifications
You must be signed in to change notification settings - Fork 0
/
tinc.8.in
345 lines (344 loc) · 10.5 KB
/
tinc.8.in
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
.Dd 2014-01-16
.Dt TINCCTL 8
.\" Manual page created by:
.\" Scott Lamb
.Sh NAME
.Nm tinc
.Nd tinc VPN control
.Sh SYNOPSIS
.Nm
.Op Fl bcn
.Op Fl -config Ns = Ns Ar DIR
.Op Fl -net Ns = Ns Ar NETNAME
.Op Fl -pidfile Ns = Ns Ar FILENAME
.Op Fl -batch
.Op Fl -force
.Op Fl -help
.Op Fl -version
.Op Ar COMMAND
.Sh DESCRIPTION
This is the control program of tinc, a secure virtual private network (VPN)
project.
.Nm
can start and stop
.Xr tincd 8 ,
and can to alter and inspect the state of a running VPN.
It can also be used to change the configuration,
or to import or export host configuration files from other nodes.
If
.Nm
is started with a
.Ar COMMAND ,
this command is immediately executed, after which
.Nm
exits.
If no
.Ar COMMAND
is given,
.Nm
will act as a shell;
it will display a prompt, and commands can be entered on the prompt.
If
.Nm
is compiled with libreadline, history and command completion are available on the prompt.
One can also pipe a script containing commands through
.Nm .
In that case, lines starting with a # symbol will be ignored.
.Sh OPTIONS
.Bl -tag -width indent
.It Fl n, -net Ns = Ns Ar NETNAME
Communicate with tincd(8) connected with
.Ar NETNAME .
.It Fl -pidfile Ns = Ns Ar FILENAME
Use the cookie from
.Ar FILENAME
to authenticate with a running tinc daemon.
If unspecified, the default is
.Pa @runstatedir@/tinc. Ns Ar NETNAME Ns Pa .pid.
.It Fl b, -batch
Don't ask for anything (non-interactive mode).
.It Fl -force
Force some commands to work despite warnings.
.It Fl -help
Display short list of options.
.It Fl -version
Output version information and exit.
.El
.Sh ENVIRONMENT VARIABLES
.Bl -tag -width indent
.It Ev NETNAME
If no netname is specified on the command line with the
.Fl n
option, the value of this environment variable is used.
.El
.Sh COMMANDS
.Bl -tag -width indent
.It init Op Ar name
Create initial configuration files and RSA and Ed25519 key pairs with default length.
If no
.Ar name
for this node is given, it will be asked for.
.It get Ar variable
Print the current value of configuration variable
.Ar variable .
If more than one variable with the same name exists,
the value of each of them will be printed on a separate line.
.It set Ar variable Ar value
Set configuration variable
.Ar variable
to the given
.Ar value .
All previously existing configuration variables with the same name are removed.
To set a variable for a specific host, use the notation
.Ar host Ns Li . Ns Ar variable .
.It add Ar variable Ar value
As above, but without removing any previously existing configuration variables.
If the variable already exists with the given value, nothing happens.
.It del Ar variable Op Ar value
Remove configuration variables with the same name and
.Ar value .
If no
.Ar value
is given, all configuration variables with the same name will be removed.
.It edit Ar filename
Start an editor for the given configuration file.
You do not need to specify the full path to the file.
.It export
Export the host configuration file of the local node to standard output.
.It export-all
Export all host configuration files to standard output.
.It import
Import host configuration data generated by the
.Nm
export command from standard input.
Already existing host configuration files are not overwritten unless the option
.Fl -force
is used.
.It exchange
The same as export followed by import.
.It exchange-all
The same as export-all followed by import.
.It invite Ar name
Prepares an invitation for a new node with the given
.Ar name ,
and prints a short invitation URL that can be used with the join command.
.It join Op Ar URL
Join an existing VPN using an invitation URL created using the invite command.
If no
.Ar URL
is given, it will be read from standard input.
.It start Op tincd options
Start
.Xr tincd 8 ,
optionally with the given extra options.
.It stop
Stop
.Xr tincd 8 .
.It restart Op tincd options
Restart
.Xr tincd 8 ,
optionally with the given extra options.
.It reload
Partially rereads configuration files. Connections to hosts whose host
config files are removed are closed. New outgoing connections specified
in
.Xr tinc.conf 5
will be made.
.It pid
Shows the PID of the currently running
.Xr tincd 8 .
.It generate-keys Op bits
Generate both RSA and Ed25519 key pairs (see below) and exit.
.It generate-ed25519-keys
Generate public/private Ed25519 key pair and exit.
.It generate-rsa-keys Op bits
Generate public/private RSA key pair and exit.
If
.Ar bits
is omitted, the default length will be 2048 bits.
When saving keys to existing files, tinc will not delete the old keys;
you have to remove them manually.
.It dump [reachable] nodes
Dump a list of all known nodes in the VPN.
If the keyword reachable is used, only lists reachable nodes.
.It dump edges
Dump a list of all known connections in the VPN.
.It dump subnets
Dump a list of all known subnets in the VPN.
.It dump connections
Dump a list of all meta connections with ourself.
.It dump graph | digraph
Dump a graph of the VPN in
.Xr dotty 1
format.
Nodes are colored according to their reachability:
red nodes are unreachable, orange nodes are indirectly reachable, green nodes are directly reachable.
Black nodes are either directly or indirectly reachable, but direct reachability has not been tried yet.
.It dump invitations
Dump a list of outstanding invitations.
The filename of the invitation, as well as the name of the node that is being invited is shown for each invitation.
.It info Ar node | subnet | address
Show information about a particular node, subnet or address.
If an address is given, any matching subnet will be shown.
.It purge
Purges all information remembered about unreachable nodes.
.It debug Ar N
Sets debug level to
.Ar N .
.It log Op Ar N
Capture log messages from a running tinc daemon.
An optional debug level can be given that will be applied only for log messages sent to
.Nm tinc .
.It retry
Forces
.Xr tincd 8
to try to connect to all uplinks immediately.
Usually
.Xr tincd 8
attempts to do this itself,
but increases the time it waits between the attempts each time it failed,
and if
.Xr tincd 8
didn't succeed to connect to an uplink the first time after it started,
it defaults to the maximum time of 15 minutes.
.It disconnect Ar NODE
Closes the meta connection with the given
.Ar NODE .
.It top
If
.Nm
is compiled with libcurses support, this will display live traffic statistics
for all the known nodes, similar to the UNIX
.Xr top 1
command.
See below for more information.
.It pcap
Dump VPN traffic going through the local tinc node in
.Xr pcap-savefile 5
format to standard output,
from where it can be redirected to a file or piped through a program that can parse it directly,
such as
.Xr tcpdump 8 .
.It network Op Ar netname
If
.Ar netname
is given, switch to that network.
Otherwise, display a list of all networks for which configuration files exist.
.It fsck
This will check the configuration files for possible problems,
such as unsafe file permissions, missing executable bit on script,
unknown and obsolete configuration variables, wrong public and/or private keys, and so on.
.Pp
When problems are found, this will be printed on a line with WARNING or ERROR in front of it.
Most problems must be corrected by the user itself, however in some cases (like file permissions and missing public keys),
tinc will ask if it should fix the problem.
.It sign Op Ar filename
Sign a file with the local node's private key.
If no
.Ar filename
is given, the file is read from standard input.
The signed file is written to standard output.
.It verify Ar name Op Ar filename
Check the signature of a file against a node's public key.
The
.Ar name
of the node must be given,
or can be
.Li .
to check against the local node's public key, or
.Li *
to allow a signature from any node whose public key is known.
If no
.Ar filename
is given, the file is read from standard input.
If the verification is successful,
a copy of the input with the signature removed is written to standard output,
and the exit code will be zero.
If the verification failed,
nothing will be written to standard output, and the exit code will be non-zero.
.El
.Sh EXAMPLES
Examples of some commands:
.Bd -literal -offset indent
tinc -n vpn dump graph | circo -Txlib
tinc -n vpn pcap | tcpdump -r -
tinc -n vpn top
.Pp
.Ed
Examples of changing the configuration using
.Nm :
.Bd -literal -offset indent
tinc -n vpn init foo
tinc -n vpn add Subnet 192.168.1.0/24
tinc -n vpn add bar.Address bar.example.com
tinc -n vpn add ConnectTo bar
tinc -n vpn export | gpg --clearsign | mail -s "My config" [email protected]
.Ed
.Sh TOP
The top command connects to a running tinc daemon and repeatedly queries its per-node traffic counters.
It displays a list of all the known nodes in the left-most column,
and the amount of bytes and packets read from and sent to each node in the other columns.
By default, the information is updated every second.
The behaviour of the top command can be changed using the following keys:
.Bl -tag
.It Ic s
Change the interval between updates.
After pressing the
.Ic s
key, enter the desired interval in seconds, followed by enter.
Fractional seconds are honored.
Intervals lower than 0.1 seconds are not allowed.
.It Ic c
Toggle between displaying current traffic rates (in packets and bytes per second)
and cumulative traffic (total packets and bytes since the tinc daemon started).
.It Ic n
Sort the list of nodes by name.
.It Ic i
Sort the list of nodes by incoming amount of bytes.
.It Ic I
Sort the list of nodes by incoming amount of packets.
.It Ic o
Sort the list of nodes by outgoing amount of bytes.
.It Ic O
Sort the list of nodes by outgoing amount of packets.
.It Ic t
Sort the list of nodes by sum of incoming and outgoing amount of bytes.
.It Ic T
Sort the list of nodes by sum of incoming and outgoing amount of packets.
.It Ic b
Show amount of traffic in bytes.
.It Ic k
Show amount of traffic in kilobytes.
.It Ic M
Show amount of traffic in megabytes.
.It Ic G
Show amount of traffic in gigabytes.
.It Ic q
Quit.
.El
.Sh BUGS
If you find any bugs, report them to [email protected].
.Sh SEE ALSO
.Xr tincd 8 ,
.Xr tinc.conf 5 ,
.Xr dotty 1 ,
.Xr pcap-savefile 5 ,
.Xr tcpdump 8 ,
.Xr top 1 ,
.Pa http:https://www.tinc-vpn.org/ ,
.Pa http:https://www.cabal.org/ .
.Pp
The full documentation for tinc is maintained as a Texinfo manual.
If the info and tinc programs are properly installed at your site,
the command
.Ic info tinc
should give you access to the complete manual.
.Pp
tinc comes with ABSOLUTELY NO WARRANTY.
This is free software, and you are welcome to redistribute it under certain conditions;
see the file COPYING for details.
.Sh AUTHORS
.An "Ivo Timmermans"
.An "Guus Sliepen" Aq [email protected]
.Pp
And thanks to many others for their contributions to tinc!