Skip to content
New issue

Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.

By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.

Already on GitHub? Sign in to your account

DietPi | WiFi connection with static IP address fail #515

Closed
k-plan opened this issue Sep 17, 2016 · 28 comments
Closed

DietPi | WiFi connection with static IP address fail #515

k-plan opened this issue Sep 17, 2016 · 28 comments
Assignees
Milestone

Comments

@k-plan
Copy link
Contributor

k-plan commented Sep 17, 2016

https://dietpi.com/phpbb/viewtopic.php?p=2929#p2929

@k-plan k-plan added the Jessie label Sep 17, 2016
@Fourdee Fourdee added this to the v131 milestone Sep 17, 2016
@Fourdee
Copy link
Collaborator

Fourdee commented Sep 17, 2016

https://github.com/Fourdee/DietPi/issues/474#issuecomment-244546570
Fourdee@007b8ca

New image should solve this. But i'll test.

@k-plan
Copy link
Contributor Author

k-plan commented Sep 17, 2016

Ready to go with my RPi B+, RPi Zero or RPi 3 for your new image. 😄

Please tell which device to use. 👍

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 17, 2016

@k-plan

Just did a test on RPi3 (haven't created the image yet, just a test), DHCP automation is fine, but static still fails to connect, same as reported 0.0.0.0 etc.
Weird.

I'll need to look into it, hoping it might be a kernel/firmware issue lol. 4.4.19

@k-plan
If you get a chance, would you be able to test RPi 1/2 with USB wifi dongle on v130. Not the automation side, just static IP on a completed installation?

@k-plan
Copy link
Contributor Author

k-plan commented Sep 17, 2016

If you get a chance, would you be able to test RPi 1/2 with USB wifi dongle on v130. Not the automation side, just static IP on a completed installation?

Static IP on Wifi dongle by RPI B+ did not work. (switching from DHCP)
Staitic IP on wire connection as well as DHCP wired work. (Both active WiFi=DHCP / Wired=static or DHCP)

But I will start from the scratch .... with v130 without any mod and first only with a wired connection.

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 17, 2016

@k-plan
Thanks 👍 , but no rush, will be tomorrow for me.
Just tried 4.4.21 on RPi 3. Same issue.

NETLINK: Error: Invalid argument

PS, i hate these new emotes. Bring back my yellow thumbs up! lol
image

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 17, 2016

@k-plan

Think i got it.

apt-get purge ifmetric

Remove metric 0 and metric 1 from /etc/network/interfaces

Now static IP works, on my RPi 3. Connection working ping google.com

@k-plan
Copy link
Contributor Author

k-plan commented Sep 17, 2016

v.130 on RPi B+ wired connection (DHCP) not touch dietpi.txt:

Welcome to DietPi-Software

 [Info] Testing connection to https://mirrordirector.raspbian.org/raspbian/
 [Info] Max duration of 20 seconds, please wait...
 [Ok] Connection test | Completed


 DietPi-Update
─────────────────────────────────────────────────────
 Mode: Checking for DietPi updates
 Please wait...

  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current
                                 Dload  Upload   Total   Spent    Left  Speed
100     5  100     5    0     0     26      0 --:--:-- --:--:-- --:--:--    26

 [Ok] No updates required, your DietPi installation is up to date.

 [Info] Current Version : 130
 [Info] Server Version  : 130

 DietPi-Set_Hardware
─────────────────────────────────────────────────────
 Mode: preferipversion (auto)
 Please wait...

 [Ok] preferipversion auto | Completed
 [Info] Testing connection to https://mirrordirector.raspbian.org/raspbian/
 [Info] Max duration of 20 seconds, please wait...
 [Ok] Connection test | Completed


 DietPi
─────────────────────────────────────────────────────
 Mode: Updating user data location
 Please wait...

 [Info] /mnt/dietpi_userdata is already symlinked to target directory.

 [Ok] Completed


 DietPi-Software
─────────────────────────────────────────────────────
 Mode: Update & upgrade APT
 Please wait...

Get:1 https://mirrordirector.raspbian.org jessie InRelease [14.9 kB]
Get:2 https://mirrordirector.raspbian.org jessie/main armhf Packages [8,981 kB]
Get:3 https://archive.raspberrypi.org jessie InRelease [13.2 kB]
Get:4 https://archive.raspberrypi.org jessie/main armhf Packages [146 kB]
Get:5 https://archive.raspberrypi.org jessie/ui armhf Packages [8,966 B]
Ign https://archive.raspberrypi.org jessie/main Translation-en_GB
Ign https://archive.raspberrypi.org jessie/main Translation-en
Ign https://archive.raspberrypi.org jessie/ui Translation-en_GB
Ign https://archive.raspberrypi.org jessie/ui Translation-en
Get:6 https://mirrordirector.raspbian.org jessie/contrib armhf Packages [37.5 kB]
Get:7 https://mirrordirector.raspbian.org jessie/non-free armhf Packages [70.3 kB]
Get:8 https://mirrordirector.raspbian.org jessie/rpi armhf Packages [1,356 B]
Ign https://mirrordirector.raspbian.org jessie/contrib Translation-en_GB
Ign https://mirrordirector.raspbian.org jessie/contrib Translation-en
Ign https://mirrordirector.raspbian.org jessie/main Translation-en_GB
Ign https://mirrordirector.raspbian.org jessie/main Translation-en
Ign https://mirrordirector.raspbian.org jessie/non-free Translation-en_GB
Ign https://mirrordirector.raspbian.org jessie/non-free Translation-en
Ign https://mirrordirector.raspbian.org jessie/rpi Translation-en_GB
Ign https://mirrordirector.raspbian.org jessie/rpi Translation-en
Fetched 9,274 kB in 29s (314 kB/s)
Reading package lists... Done
 [Info] Running apt simulation to check for errors, please wait...
 [Ok] Apt simulation | Completed

 ───────────────────────────────────────
 DietPi     | 19:51 | Sat 17/09/16
 ───────────────────────────────────────
 V130       | RPi B+ (armv6l)
 ───────────────────────────────────────
 IP Address | 192.168.100.89
 ───────────────────────────────────────

 Welcome to DietPi-Software


 DietPi-Software
─────────────────────────────────────────────────────
 Mode: Update & upgrade APT
 Please wait...

Reading package lists... Done
Building dependency tree
Reading state information... Done
Calculating upgrade... Done
The following packages will be upgraded:
  raspberrypi-sys-mods
1 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.
Need to get 6,312 B of archives.
After this operation, 22.5 kB of additional disk space will be used.
Get:1 https://archive.raspberrypi.org/debian/ jessie/main raspberrypi-sys-mods all 20160916 [6,312 B]
Fetched 6,312 B in 0s (15.9 kB/s)
(Reading database ... 19454 files and directories currently installed.)
Preparing to unpack .../raspberrypi-sys-mods_20160916_all.deb ...
Removing old /etc/sysctl.d/98-rpi.conf...
Adjusting vm.swappiness and vm.min_free_kbytes...
Unpacking raspberrypi-sys-mods (20160916) over (20160426) ...
Setting up raspberrypi-sys-mods (20160916) ...
Removing old sysctl tweaks if present...

 DietPi-Software
─────────────────────────────────────────────────────
 Mode: Checking for prerequisite software
 Please wait...


 DietPi-Services
─────────────────────────────────────────────────────
 Mode: stop
 Please wait...

 [Ok] cron


 DietPi-Services
─────────────────────────────────────────────────────
 Mode: stop
 Please wait...

 [Ok] cron


 DietPi-Software
─────────────────────────────────────────────────────
 Mode: Optimize and configure software
 Please wait...

 [Info] Applying DietPi optimizations and configurations for RPi B+ (armv6l)
 [Info] Please wait...

 #               processing | D I E T  P I             #


 DietPi-Services
─────────────────────────────────────────────────────
 Mode: stop
 Please wait...

 [Ok] cron


 DietPi-Services
─────────────────────────────────────────────────────
 Mode: disable
 Please wait...

 [Ok] cron


 DietPi-Software
─────────────────────────────────────────────────────
 Mode: Installation completed
 Please wait...


 The system will now reboot.
 This completes the DietPi-Software installation.

root@DietPi:~# processing | D I E T  P I #  processing

work! 👍

@k-plan
Copy link
Contributor Author

k-plan commented Sep 17, 2016

@Fourdee

Think i got it.

apt-get purge ifmetric
Remove metric 0 and metric 1 from /etc/network/interfaces

Now it works, on my RPi 3.

oh, oh ... but no metric no https://github.com/Fourdee/DietPi/issues/265

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 17, 2016

@k-plan

oh, oh ... but no metric no #265

Yep 😞. I need to re-run the tests again to confirm. But looks like we might need to find another alternative to ifmetric?

Now off to play Descent 2 (was Tron 2.0 last month) for 30 minutes before son goes bed, woop woop 😃

@k-plan
Copy link
Contributor Author

k-plan commented Sep 17, 2016

@Fourdee

ifmetric - An IPv4 route metrics manipulation tool

https://0pointer.de/lennart/projects/ifmetric/ifmetric.8.xml

https://metadata.ftp-master.debian.org/changelogs//main/i/ifmetric/ifmetric_0.3-3_changelog

But looks like we might need to find another alternative to ifmetric?

Hmm, no. It's time to use the "new" primary network configuration tools 😱

root@DietPi:~# ip -V
ip utility, iproute2-ss140804

iproute2: https://wiki.linuxfoundation.org/networking/iproute2

Most network configuration manuals still refer to ifconfig and route as the primary network configuration tools, but ifconfig is known to behave inadequately in modern network environments. They should be deprecated, but most distros still include them. Most network configuration systems make use of ifconfig and thus provide a limited feature set. The /etc/net project aims to support most modern network technologies, as it doesn't use ifconfig and allows a system administrator to make use of all iproute2 features, including traffic control.

https://www.policyrouting.org/iproute2.doc.html

https://xmodulo.com/linux-tcpip-networking-net-tools-iproute2.html

https://baturin.org/docs/iproute2/

https://www.admin-magazine.com/Archive/2013/16/Network-management-with-the-IPRoute2-toolbox

https://lartc.org/howto/lartc.iproute2.html

https://is.muni.cz/th/207915/fi_b/iproute.pdf

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

@k-plan

For now, we will remove metric and ifmetric during patch. I'll reopen https://github.com/Fourdee/DietPi/issues/265 so we can "start again" lol 👍

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

Nearly forgot.

Fix automation needs new image: 🈯 https://dietpi.com/downloads/testing/DietPi_RPi-armv6-(Jessie).7z

@Fourdee Fourdee reopened this Sep 18, 2016
@k-plan
Copy link
Contributor Author

k-plan commented Sep 18, 2016

@Fourdee

Testing:

  • with two interfaces with static ip addresses (same broadcast domain)
  • ifmetric and netplug installed

/etc/network/interfaces

#/etc/network/interfaces
#Please use DietPi-Config to modify network settings.

# Local
auto lo
iface lo inet loopback

# Ethernet
allow-hotplug eth0
iface eth0 inet static
## metric 0
address 192.168.0.100
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
dns-nameservers 8.8.8.8 8.8.4.4
post-up ip route add default via 192.168.0.1 dev eth0 metric 1
pre-down ip route del default via 192.168.0.1 dev eth0


# Wifi
allow-hotplug wlan0
iface wlan0 inet static
## metric 1
address 192.168.0.200
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
wireless-essid FuzonWifi
wireless-key abcde12345
wireless-mode Managed
wireless-power off
wpa-ssid FuzonWifi
wpa-psk abcde12345
#dns-nameservers 8.8.8.8 8.8.4.4
post-up ip route add default via 192.168.0.1 dev wlan0 metric 2
pre-down ip route del default via 192.168.0.1 dev wlan0
  • have a look at ip route show 👍
  • test with ping dietpi.com and unplug/plug in ethernet cable 👍
  • output of dmesg 👍

now we must have a look in:

  • one interface static / on interface dhcp
  • both interface dhcp

@k-plan
Copy link
Contributor Author

k-plan commented Sep 18, 2016

@Fourdee

Testing:

  • with one interfaces with static ip addresses, second with dhcp (same broadcast domain)
  • ifmetric and netplug installed

/etc/network/interfaces

#/etc/network/interfaces
#Please use DietPi-Config to modify network settings.

# Local
auto lo
iface lo inet loopback

# Ethernet
allow-hotplug eth0
iface eth0 inet static
## metric 0
address 192.168.0.100
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
dns-nameservers 8.8.8.8 8.8.4.4
post-up ip route add default via 192.168.0.1 dev eth0 metric 1
pre-down ip route del default via 192.168.0.1 dev eth0


# Wifi
allow-hotplug wlan0
iface wlan0 inet dhcp
## metric 1
address 192.168.0.200
netmask 255.255.255.0
network 192.168.0.0
broadcast 192.168.0.255
wireless-essid FuzonWifi
wireless-key abcde12345
wireless-mode Managed
wireless-power off
wpa-ssid FuzonWifi
wpa-psk abcde12345
#dns-nameservers 8.8.8.8 8.8.4.4
post-up ip route add default dev wlan0 metric 2
pre-down ip route del default dev wlan0

  • have a look at ip route show 👍
  • test with ping dietpi.com and unplug/plug in ethernet cable 👍
  • output of dmesg 👍

@k-plan
Copy link
Contributor Author

k-plan commented Sep 18, 2016

@Fourdee

Testing:

  • with two interfaces with dhcp (same broadcast domain) 👎
  • testing with iptable2 Policy Routing 👎
    Possible, it's a problem with my skill. 😞

Yes, revert to v115 practice of either wired or wifi 😢

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

@k-plan

v131 image. Static IP WiFi automation should now work correctly:
https://dietpi.com/downloads/testing/DietPi_RPi-armv6-(Jessie).7z

@k-plan
Copy link
Contributor Author

k-plan commented Sep 18, 2016

@Fourdee

v131 image. Static IP WiFi automation should now work correctly:

Tested on RPi B+ with wifi adapter and non wired connection.

  • static wifi ip, Ethernet disable, full manually installation => work 👍
  • static wifi ip, Ethernet disable, automated installation => work 👍

after reboot it is a DietPi v130

160918-0001

Hint: are you living now in USA?

160918-0002

Will you give it to "tohax" for testing? I think it will work.
But i have only tested installation with static ip on wifi, nothing more.

root@RPi-B_plus:~# uname -a
Linux RPi-B_plus 4.4.19+ #907 Tue Sep 6 13:45:45 BST 2016 armv6l GNU/Linux
[  862.302016] ------------[ cut here ]------------
[  862.302953] WARNING: CPU: 0 PID: 6 at net/wireless/sme.c:907 __cfg80211_disconnected+0x280/0x2c8 [cfg80211]()
[  862.302979] Modules linked in: 8192cu cfg80211 evdev rfkill bcm2835_gpiomem bcm2835_wdt uio_pdrv_genirq uio fuse ipv6
[  862.303036] CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.4.19+ #907
[  862.303047] Hardware name: BCM2708
[  862.303731] Workqueue: cfg80211 cfg80211_event_work [cfg80211]
[  862.303806] [<c0016cfc>] (unwind_backtrace) from [<c0013c20>] (show_stack+0x20/0x24)
[  862.303843] [<c0013c20>] (show_stack) from [<c02e38fc>] (dump_stack+0x20/0x28)
[  862.303874] [<c02e38fc>] (dump_stack) from [<c0021eb4>] (warn_slowpath_common+0x8c/0xc4)
[  862.303898] [<c0021eb4>] (warn_slowpath_common) from [<c0021fa8>] (warn_slowpath_null+0x2c/0x34)
[  862.304597] [<c0021fa8>] (warn_slowpath_null) from [<bf0edb84>] (__cfg80211_disconnected+0x280/0x2c8 [cfg80211])
[  862.305845] [<bf0edb84>] (__cfg80211_disconnected [cfg80211]) from [<bf0c90ac>] (cfg80211_process_wdev_events+0x1a0/0x20c [cfg80211])
[  862.307264] [<bf0c90ac>] (cfg80211_process_wdev_events [cfg80211]) from [<bf0c9154>] (cfg80211_process_rdev_events+0x3c/0x74 [cfg80211])
[  862.308635] [<bf0c9154>] (cfg80211_process_rdev_events [cfg80211]) from [<bf0c4208>] (cfg80211_event_work+0x24/0x2c [cfg80211])
[  862.309498] [<bf0c4208>] (cfg80211_event_work [cfg80211]) from [<c0037540>] (process_one_work+0x11c/0x39c)
[  862.309543] [<c0037540>] (process_one_work) from [<c0037800>] (worker_thread+0x40/0x4d0)
[  862.309576] [<c0037800>] (worker_thread) from [<c003d184>] (kthread+0xdc/0xf8)
[  862.309614] [<c003d184>] (kthread) from [<c000f8a8>] (ret_from_fork+0x14/0x2c)
[  862.309629] ---[ end trace 5bdaf355baab1b64 ]---
[  862.848400] usbcore: registered new interface driver brcmfmac

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

@k-plan

Hint: are you living now in USA?

I wish, furthest I'am going is Skegness lol (daytona USA arcades!): https://www.skegness.net/

I'll redo the image with those removed. Not sure how they got there. Good spot 👍

Will you give it to "tohax" for testing? I think it will work.

I tested on RPi3 with onboard WiFi and static, worked for me. Was hoping to get v131 out today, but its most likely Monday/Tuesday now.
Pretty confidant we have resolved the issue. I'll get v131 wrapped up 1st, then we can let him know of the new image?

@k-plan
Copy link
Contributor Author

k-plan commented Sep 18, 2016

@Fourdee

I wonder, because noting set in dietpi.txt

#WiFi country code. 2 character value (eg GB US DE JP): https://en.wikipedia.org/wiki/ISO_3166-1_alpha-2
wifi_country_code=

.. and it is set to GB if it is boot up after installation.

[   12.634275] cfg80211: Regulatory domain changed to country: GB
[   12.634320] cfg80211:  DFS Master region: ETSI
[   12.634334] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[   12.634356] cfg80211:   (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[   12.634375] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[   12.634394] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[   12.634411] cfg80211:   (5490000 KHz - 5710000 KHz @ 160000 KHz), (N/A, 2700 mBm), (0 s)
[   12.634427] cfg80211:   (57000000 KHz - 66000000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

@k-plan

https://github.com/Fourdee/DietPi/blob/master/dietpi/finalise#L110-L111

Should be 00, i'll change that.

Note to self:
Bring up wifi to set this before finalize.

@tohax
Copy link

tohax commented Sep 18, 2016

v131 image did not solve problem for me. Connection test failed again, but now there is a proper ip address in dietpi banner, there was emty field before.

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 18, 2016

@tohax

Connection test failed again

Raspbian mirror director was offline for me. I had to change to a static mirror.

Try:

cat << _EOF_ > /etc/apt/sources.list
deb https://mirror.ox.ac.uk/sites/archive.raspbian.org/archive/raspbian jessie main contrib non-free rpi
_EOF_
dietpi-software

@tohax
Copy link

tohax commented Sep 18, 2016

i'll try and report tomorrow. need to sleep.

@tohax
Copy link

tohax commented Sep 19, 2016

it's alive!!! Everything works fine. Thank you.

@k-plan
Copy link
Contributor Author

k-plan commented Sep 19, 2016

@Fourdee

Should be 00, i'll change that.

Hmm, I would say, locales, keyboard, time zone, country code =>> GB

what's consistent, because Fourdee + DietPi = 🇬🇧

😄

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 19, 2016

@k-plan

Hmm, I would say, locales, keyboard, time zone, country code =>> GB

Would be nice for me lol.
But, I can see people "kicking off" with the legality of a GB wifi region, in a country that its against the law to use. So, must really set 00 for WiFi.

@Fourdee
Copy link
Collaborator

Fourdee commented Sep 19, 2016

@k-plan

But, I can see people "kicking off" with the legality of a GB wifi region, in a country that its against the law to use. So, must really set 00 for WiFi.

Although, I just checked the official Raspbian image, it has this set to GB by default. I'am game. We'll set to GB by default on all DietPi images.

Fourdee referenced this issue Sep 19, 2016
+ FStrim on finalize. Stable when using sync so far.
+ WiFi country code GB by default, same as Raspbian:
https://github.com/Fourdee/DietPi/issues/515#issuecomment-247980082
@Fourdee
Copy link
Collaborator

Fourdee commented Sep 19, 2016

@tohax

it's alive!!! Everything works fine. Thank you.

Excellent thanks for letting us know 👍

Marking this as closed.

@Fourdee Fourdee closed this as completed Sep 19, 2016
@Fourdee Fourdee mentioned this issue Sep 20, 2016
Fourdee referenced this issue Sep 20, 2016
v131
(20/09/16)

New Image:

OrangePi One | Is now available. Implementation possible, with thanks to K-Plan: https://dietpi.com/download

New Features:

DietPi-Drive_Manager | Lightweight Drive Manager (eg: gparted). Allows you to mount, dismount, format EXT4/NTFS/FAT32/HFS+/BTRFS, toggle UUID mounting and control multiple (max 5) external/USB drives, for use on your DietPi system: https://github.com/Fourdee/DietPi/issues/271

Changes / Improvements / Optimizations:

DietPi-Software | Added installation options for NFS server and client: https://github.com/Fourdee/DietPi/issues/246

DietPi-Software | Added installation options for UrBackup Server: https://github.com/Fourdee/DietPi/issues/494

DietPi-Software | CertBot will now automatically install required packages, rather than prompt user.

DietPi-Software | Emby Media Server is now available for BPi M2+ BPi Pro and OPi PC. Thanks to John for testing with his BPi Pro (M1): https://dietpi.com/phpbb/viewtopic.php?f=11&t=644&p=2860#p2853

DietPi-Config | Added ability to mount NFS shares in Networking: NAS menu.

Raspberry Pi | Image download updated to v131: https://dietpi.com/download

Raspberry Pi | Image v131. We have changed from the unstable, unreliable and slow Raspbian Mirror Director, to Oxford UK Mirror: https://github.com/Fourdee/DietPi/issues/518. Requires v131 image or higher.

General | When inserting one USB drive to system, it will be mounted automaticaly to /mnt/usb_1 when plugged in: https://github.com/Fourdee/DietPi/issues/501

General | Dedicated USB drive setup will now set the UUID in /etc/fstab

General | HFS+ filesystem is now supported on all DietPi images.

General | You can now check bootup time duration, by running 'cat /var/log/boottime'. This is the duration from boot, to when SystemD has finished. TIP: Boot times can vastly be reduced, by using a static IP address.

DietPi-Lets_Encrypt | Now supports Apache2 and Lighttpd webserver stacks: https://github.com/Fourdee/DietPi/issues/479. Many thanks to aar0nism for posting a excellent guide we based this on: https://dietpi.com/phpbb/viewtopic.php?f=9&t=603&p=2625#p2624

Bug fixes:

DietPi-Software | Resolved an issue where FFMPEG did not install libmp3lame0 on RPi 1. Many thanks to Erayan for reporting this: https://github.com/Fourdee/DietPi/issues/511

DietPi-Software | Automatic moving of user data is now limited to 1st run installation only.

DietPi-Config | Resolved an issue where static IP WiFi connections failed to route data: https://github.com/Fourdee/DietPi/issues/515

DietPi-Cloudshell | Resolved an issue where the Storage scene would hang, if a unavailable NFS mount 
was used as custom USB device. Many thanks to John for reporting and testing this: https://github.com/Fourdee/DietPi/issues/395

DietPi-Automation | Resolved an issue where connection tests would not wait 1 second, before trying again. This occured when there was no available network.

Image | We have found a possible image/filesystem corruption on our Odroid C2 image. The image has been reverted back to a previous stable image and updated to v130: https://github.com/Fourdee/DietPi/issues/507

General | Resolved an issue where setting snd-bcm2835 soundcard did not set avoid_pwm_pll=0 (to allow HQ audio).
Sign up for free to join this conversation on GitHub. Already have an account? Sign in to comment
Projects
None yet
Development

No branches or pull requests

3 participants