Plant Watering Sensor Project for Zigbee Network (based on the Source Code of the DIYRUZ Flower Project - https://github.com/diyruz/flower)
Powered by SoC CC2530, the sensor is based on a capacitive measurement method. The sensor is powered by a CR 2450 battery (CR 2477).
Donate to me: https://paypal.me/efektalab or just buy to support this project
Video: https://youtu.be/DzgeWvG4MEI
Telegram ZigDev - https://t.me/zigdev
Telegram DiyDev - https://t.me/diy_devices
More info at https://efektalab.com/eON_PWS_Z
CC2530 E18-MS1-PCB - https://ali.ski/v8RP7i (10pcs)
CC2530 E18-MS1-PCB - https://ali.ski/o_TBGP
Tantalum Capacitor 220uF - https://ali.ski/VApfn
SMD LED 0805 - https://ali.ski/wb6ZP
1% SMD Resistor Kit Assorted Kit 1R-1M 0603 - https://ali.ski/npItF
SMD Chip Multilayer Ceramic Capacitor 0603 10pF 50V - https://ali.ski/p3yr60
SMD Chip Multilayer Ceramic Capacitor 0603 100nF 50V - https://ali.ski/p3yr60
1N4148WS - https://ali.ski/cOCdto
Cell Holder CR2450 - https://ali.ski/VdotsA
Micro Button Tact Switch SMD 4Pin 3X4X2.5 - https://ali.ski/sGwFu
IRLML6402TRPBF - https://ali.ski/_iNbX
Micro Screws M1.4 5mm - https://ali.ski/gaFdO
-
Download the Smart RF Flash Programmer V1 https://www.ti.com/tool/FLASH-PROGRAMMER
-
Open the application select the HEX firmware file
-
Connect the device with wires to CCDebugger, first erase the chip, then flash it.
https://github.com/ZigDevWiki/zigdevwiki.github.io/blob/main/docs/Begin/IAR_install.md
https://github.com/sigma7i/zigbee-wiki/wiki/zigbee-firmware-install (RU)
- https://github.com/smartboxchannel/Plant-Watering-Sensor-Zigbee/blob/main/majordomo-zigbee2mqtt/README.md (MJD https://mjdm.ru/)
- Press and hold button (1) for 2-3 seconds, until device start flashing led
- Wait, in case of successfull join, device will flash led 5 times
- If join failed, device will flash led 3 times
- Hold button (1) for 10 seconds, this will reset device to FN(factory new) status
- Go to step 1 for FN device
If a device does not connect to your coordinator, please try the following:
- Power off all routers in your network.
- Move the device near to your coordinator (about 1 meter).
or if you cannot disable routers (for example, internal switches), you may try the following:
- Disconnect an external antenna from your coordinator.
- Move a device to your coordinator closely (1-3 centimeters).
- Power on, power on the device.
- Restart your coordinator (for example, restart Zigbee2MQTT if you use it).
Please, ensure the following:
- Your power source is OK (a battery has more than 3V). You can temporarily use an external power source for testings (for example, from a debugger).
- The RF part of your E18 board works. You can upload another firmware to it and try to pair it with your coordinator. Or you may use another coordinator and build a separate Zigbee network for testing.
- Your coordinator has free slots for direct connections.
- You permit joining on your coordinator.
- Your device did not join to other opened Zigbee network. When you press and hold the button, it should flash every 3-4 seconds. It means that the device in the joining state.