remove_design -all
set power_preserve_rtl_hier_names "true"
set search_path "/home/home2/students/afzalikusha/CGRA/Multiplier_Ref/YUS_V2_2"
define_design_lib work -path "work"
set topname "ERCM8_V2_2"
#***********************************************
#*Preliminary Preparing
#***********************************************
read_verilog {ERCM8_V2_2.v}
#***********************************************
#*Reading Libraries
#***********************************************
read_file "/home/home2/students/afzalikusha/ScaledLibraries/Library_Date_19/nanGate_ccs_15_LS.db"
#read_file "/home/home2/students/afzalikusha/NangateLibrary15nm/15nmFinFET.db "
set link_library "/home/home2/students/afzalikusha/ScaledLibraries/Library_Date_19/nanGate_ccs_15_LS.db"
#set link_library "/home/home2/students/afzalikusha/NangateLibrary15nm/15nmFinFET.db "			 
set target_library "/home/home2/students/afzalikusha/ScaledLibraries/Library_Date_19/nanGate_ccs_15_LS.db"
#set target_library "/home/home2/students/afzalikusha/NangateLibrary15nm/15nmFinFET.db "			
list_libs
#***********************************************
#*
#***********************************************
current_design $topname
analyze -format verilog -lib work "ERCM8_V2_2.v"
elaborate $topname -lib work
set auto_wire_load_selection "true"
##for below command: at first you should simulate the circit with zero delay. After that, DC will give a minimum delay. 
#Then you should put the minimum delay instead of zero till met the constraints.
set_max_delay 2.500 -from [ get_ports -filter {@port_direction == in}] -to [ get_ports -filter {@port_direction == out}]
#***********************************************
#*Setting Conditions
#***********************************************
##################################
#compile
###################################
compile 
###########################################################################################################
## you should create a folder with outputs name in your simulation path. This make the simulation easier. 
###########################################################################################################
#check_design 
write -hier -format verilog -out "~/CGRA/Multiplier_Ref/YUS_V2_2/ModelsimFiles/SynERCM8_V2_2.v"
write_sdf -version 2.1 "~/CGRA/Multiplier_Ref/YUS_V2_2/ModelsimFiles/SynERCM8_V2_2.sdf"
write -hierarchy -output "~/CGRA/Multiplier_Ref/YUS_V2_2/ModelsimFiles/SynERCM8_V2_2.ddc"
###########################################################################################################
##Reports
###########################################################################################################
report_timing -path full -delay max -max_paths 10 -nworst 1  > "~/CGRA/Multiplier_Ref/YUS_V2_2/Reports/ERCM8_V2_2_timing.report"
report_constraint -all_violators > "~/CGRA/Multiplier_Ref/YUS_V2_2/Reports/ERCM8_V2_2_constraint.report"
report_power -hierarchy > "~/CGRA/Multiplier_Ref/YUS_V2_2/Reports/ERCM8_V2_2_power.report"
report_power -cell > "~/CGRA/Multiplier_Ref/YUS_V2_2/Reports/ERCM8_V2_2_power_Cell.report"
report_area  > "../../Multiplier_Ref/YUS_V2_2/Reports/ERCM8_V2_2_area.report"

exit